to the User Guide for Grey Flow 01
Contents
1. Ah UP auto backflush activated Down auto backflush de activated If air pump for self cleaning mechanism is not used please seal grommet connection To Grey Flow Float switch To Grey Flow air pump To Grey Flow Water pump INSTALLATION STEP THREE Connecting grey water supply pipe to pump discharge Ground level 1 LDPE barb elbow with ratchet clip not supplied to be purchased separately INSTALLATION STEP THREE Running the supply line to the garden amp setting up the drip line Grey Flow Purple drip line Make a whole with punch tool amp insert drip line F fittings 1 LDPE Purple not supplied Dripline layout in garden areas k IRRIGATION AREA BOUNDARY Grey Flow Purple drip line Maximum run length 23 feet Make a whole with punch tool amp insert drip line fittings to be purchased separately Mound mater INSTALLATION STEP THREE Drip irrigation system layout The installation of the irrigation part of the Grey Flow must follow the following sequence and procedure 1 For each zone lay the 1 polypipe as header line on the ground across the wider section of the garden bed and not further than 33 feet away from the end of the bed Close the end of the 1 header line with end plugs 2 Connect the Start Connectors by punching a whole in 1 poly2. 1 Reinforced plastic lockable lid 1 Additional pit extension 12 3 4 high supplied in 4 panels to be assembled and fitted if required C O C O 2 6 screw in PVC caps 1 Extra holding bracket to be used only when additional extension is used a 7 1 Oil cooled thermal protected submersible pump to be connected as a centrifugal LA pump assembles with 2 x 1 brass check valves amp 1 discharge manifold Hl 1 Fully fitted float switch it 1 Control box 2 Spare filters Grey Water Warning Sign 1 Corflute Grey Water warnong sign to be visible at all time MOLINA pater INSTALLATION The Grey Flow 001 model is not suited to conditions where the invert level of the Grey Water pipe is lower than 2 feet below ground If the Grey Water pipe is lower than 2 feet below ground use the Grey Flow PS model instead Do not use more than the one extra extension supplied with the system Mound mater INSTALLATION To avoid Grey Water overflow to sewer use all 330 feet of Grey Flow Drip line 330 ft per station i Do not run drip line more than 23 feet from the start of the feeder pipe Use minimum 1 feeder pipe QQQ Use GF Rotor valve or a flow based indexer not pressure based to split the system into more than one station this ensures that the pump never runs against a close line y Maximum run length 23 feet Do not connect to existing system or substitute drip line the
3. GreyFlow Below Ground Series USER S MANUAL Introduction e Installation e Maintenance Grey Water reuse system O Grey Flow 001 Builder s Kit UP GF 001 BK O Grey Flow 001 Finishing Kit standard pump UP GF 001 FK Ne O Grey Flow 001 Finishing Kit with large pressure pump UP GF 001 FK LP WaterMark IAPMO M MOLINA pater MOVING mater CONTENTS INTRODUCTION Page 4 Requirements Page 5 INSTALLATION Parts List Grey Flow 001 System Page 6 7 Important Do s and Don ts Page 8 10 Step One Plumbing Installation Page 11 14 Step Two Installing the Grey Flow Electrical Components Page 15 18 Step Three Installing the Grey Flow Watering System Page 19 22 TROUBLESHOOTING GUIDE Page 23 24 MAINTENANCE Page 25 TERMS OF WARRANTY Page 27 28 DISCLAIMER Page 29 M MOLINA pater INTRODUCTION Congratulations You have taken an important step towards an environmentally friendly living with your purchase of the Universal GREY FLOW 001 Grey Water diversion and reuse system The GREY FLOW 001 System is an Entire Grey Water diverter that promotes a cleaner and healthier environment with its innovative no holding tank design The GREY FLOW 001 System is especially designed for in ground installation with Grey Water diverted through the system for use in the garden through sub surface irrigation The 001 System is suitable only for installation where the sewer pipe is between 0 to
4. 2 feet from the ground level Please Note The 001 System is NOT suitable for the Grey Water from the kitchen sinks Instant diversion to sewer by 1 Electrical switch remote control devices are also available 2 Rain Switch 3 Soil Moisture sensor switch The soil moisture sensor switch will help to avoid Grey Water run off and trigger an automatic shut down of the system when the soil is saturated Please check with authorised dealer for ideal moisture sensor switch to meet your requirements Manual diversion of the Grey Water can be achieved by using the supplied rubber plugs to seal the diversion holes inside the inter ceptor unit ref diagrams overleaf The GREY FLOW 001 can be used in conjunction with Water Rotor valve indexer to achieve water distribution over a number of stations up to 6 The GREY FLOW 001 system has Watermark and IAPMO UPC certifications is approved for use in all states and could be considered for government s Grey Water rebates wherever available DEFINITION Grey Water is wastewater generated from domestic activities such as laundry shower and bathing which can be recycled on site for uses such as landscape irrigation and constructed wetlands This wastewater contains no fecal matter human feces Grey Water differs from water from toilets which is designated sewage or blackwater to indicate it contains human waste aMMa Mound mater REQUIREMENTS The Grey Flow 001 is
5. Back flow valve not supplied with kit 4 Grey Water pipe from house INSTALLATION STEP TWO Step Fix Grey Flow controller onto house 1of4 wall close to outdoor GPO House Wall Fix Grey Flow controller to house wall using box legs and screws found inside control box Filter access Filter access Grey water pipe connection INSTALLATION STEP TWO Step Install conduit from pump pit to 2014 wall mounted controller 1 House Wall J 1 electrical conduit Filter access Filter access 4 p q gpm i Grey water pipe connection INSTALLATION STEP TWO Step Pull wires through conduit 3 of 4 g IG Pull through sensor and pump cables House Wall Filter access Filter access F Grey water pipe connection INSTALLATION STEP TWO Grey Flow electrical details Dip switch 2 Mount the controller ala wa Right setting for 001 amp on the wall using the 4 programming codes US models legs which are supplied Left Setting for PS with each controller a models j a Wire connection points for moisture sensor control option LED indicator light 7 a 5 any wire any wire gt no wire 3 pin plug to Outdoor GPO 1 of rf Dip switch 1
6. a period of ONE YEAR from the date of original retail purchase warranty period Warranty work will be done in accordance with the following terms and conditions This warranty only benefits the original purchaser THIS WARRANTY COVERS ONLY DEFECTS IN MATERIAL AND WORKMANSHIP THIS WARRANTY DOES NOT COVER ANY OF THE FOLLOWING 1 Expendable items that can wear out from normal use including but not limited to filters or similar perishable parts 2 Damage to or failure of this System if it is not installed operated or maintained according to all instructions supplied with the System 3 Damage to or failure of this System resulting from accident abuse misuse or use for other than its intended purpose Act of God 4 Damage to or failure of parts or systems resulting incomplete or improper installation or from unauthorized modifications made to this System 5 If you purchased the System from an unauthorized retailer or dealer 6 Damage caused by power surges electrical storm damage incorrect power supply or insect or vermin infestation 7 Damage to or failure of parts if this System is serviced or repaired by anyone other than an Authorized Service Center 8 This warranty extends only to you the original purchaser It is not transferable to anyone who subsequently purchased this product from you 9 Use for more than a single family or use in a commercial establishment or for commercial non household purposes 10 P
7. SOUGHT OR A CLAIM MADE UNDER THIS WARRANTY OR AS A TORT CLAIM INCLUDING NEGLIGENCE AND STRICT PRODUCT LIABILITY A CONTRACT CLAIM OR ANY OTHER CLAIM THIS LIMITATION CANNOT BE WAIVED OR AMENDED BY ANY PERSON THIS LIMITATION OF LIABILITY IS EFFECTIVE EVEN IF AWWS ORANY AUTHORIZED REPRESENTATIVE OF AWWS HAS BEEN ADVISED BY YOU OF THE POSSIBILITY OF SUCH DAMAGES THIS LIMITATION OF LIABILITY HOWEVER SHALL NOT APPLY TO CLAIMS OF PERSONAL INJURY Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages or do not allow a limitation on how long an implied warranty lasts so the above limitations or exclusions may not apply to you You are advised to contact applicable state laws for a full determination of your rights This warranty gives you specific legal rights and you may have other rights which vary from state to state No AWWS dealer agent or employee is authorized to make any modification extension change or amendment to this warranty WG AWW Susa Advanced Waste Water System Head Office USA 9901 San Fernando Rd 33 Los Angeles CA 91331 Phone 310 869 7676 WWW aWWS US UNIVERSAL M GREYFLOW a MOVING mater
8. arts and Systems not supplied by AWWS USA are not covered by this warranty Any item which has been repaired or replaced under this warranty shall be covered for the remainder of the original warranty as extended by the number of days that the product has been out of your hands for repair YOUR RESPONSIBILITY The above limited warranties are subject to the following conditions You must provide your original bill of sale invoice or other proof of purchase of the System showing that you are the original purchaser that the purchase was made within one year of the date of your claim and that you purchased it from an authorized dealer or retailer No warranty work will be done without this information Keep a copy of your receipt or invoice for your own records These limited warranties are effective only if this System is purchased and used in the United States Labor and service charges for warranty repair installation set up and adjustment of customer controls are not covered by these limited warranties Should you encounter a defect in the System go to WWW AWWS US to find the closest authorized service center Contact the center and it will arrange for an inspection and corrective action if needed and if covered by this warranty Should the center determine that the System is not covered by this warranty any corrective work will be performed at your request and at your expense If the center makes a second and or subsequent visit and
9. determines that there is no problem or that the System is not covered the service call will be charged to you When making a warranty claim please be prepared to provide a description of the System your name address work day telephone number a description of the problem the date you purchased the System and the identify of the seller i Mound mater DISCLAIMER OF IMPLIED WARRANTIES LIMITATION OF REMEDIES 1 ALL IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE YOU PURCHASED THE PRODUCT NEITHER AWWS NOR ITS AFFILIATES ARE RESPONSIBLE OR LIABLE FOR ANY LOSS INCONVENIENCE OR DAMAGE WHETHER SPECIAL EXEMPLARY DIRECT INCIDENTAL CONSEQUENTIAL OR OTHERWISE AND WHETHER KNOWN OR SHOULD HAVE BEEN KNOWN TO AWWS INCLUDING DAMAGE TO OR REPLACEMENT OF OTHER EQUIPMENT AND PROPERTY AND PERSONAL INJURY RESULTING FROM ANY BREACH OF WARRANTY THE INABILITY TO USE THE PRODUCT OR UNDER ANY LEGAL THEORY IN CONTRACT OR TORT THESE WARRANTIES AND REMEDIES ARE THE SOLE AND EXCLUSIVE WARRANTIES AND REMEDIES GIVEN BY AWWS IN CONNECTION WITH THE SALE AND USE OF THE PRODUCT NO OTHER WARRANTIES ORAL OR WRITTEN EXPRESS OR IMPLIED ARE GIVEN IN ANY EVENT AWWS S ENTIRE LIABILITY SHALL BE LIMITED TO THE ACTUAL PURCHASE PRICE YOU PAID TO THE RETAIL SELLER OF THE DEFECTIVE PRODUCT THIS LIMITATION APPLIES WHETHER DAMAGES ARE
10. e filter chamber If water is detected find and fix leaky tap inside the house 2 Potential Cause The check valves on the discharge of the pump are not closing properly Action Remove check valve and thoroughly wash all parts F The controller is operating normally water in the house is off but the pump is on all the time 1 Potential Cause The sensor wires are shorting Action Make sure that the sensor switch wires are not shorting 2 Potential Cause The sensor switch is installed in the wrong position Action Twist the sensor switch so that the white marking on the sensor stem is facing upward 3 Potential Cause The sensor switch is stuck in the close position Action Pull out sensor from holding tee clean sensor and the inside of the tee and reinstall sensor in original position 4 Potential Cause The controller is defective Action Contact your local Grey Flow supplier with proof of purchase _ oM Mound mater MAINTENANCE To retain the original reliability and performance of the Grey Flow 001 System the following maintenance procedure should be followed Please ensure that you wash your hands thoroughly after contact with Grey Water or handling any part of the Grey Flow System The following maintenance steps should be carried out once a month and not less than every 3 months A Open top cover of the interception unit B Remove primary sponge filter and wash thoroughly in a bucket
11. expansion foam Ground Level Glue the 6 Fit the extra holding bracket supplied screw on caps across the top of the main pit to to the top of the strengthen the side panels interceptors 4 Grey Water pipe from house MOLINA pater INSTALLATION STEP ONE All plumbing work must be performed by a licensed plumber The Grey Flow 001 model is not suited to conditions where the invert level of the Grey Water pipe is lower than 2 feet below ground Do not use more than the one extension supplied If the Grey Water pipe is lower than2 feet below ground use the Grey Flow PS model instead 1 Install the main pit in the below ground hole connect and glue to incoming Grey Water pipe and sewer overflow the interceptors in the pit must be kept in vertical position 2 Glue 6 screw in on caps to the top of the interceptors keep filters in the vertical position 3 If ground level is still higher then the top of the main pit 3 1 Fit extra holding bracket across the top of the main pit to strengthen the side panels 3 2 Cut the additional pit extension panels to size 3 3 Assemble the panels and fit over the main pit 3 4 Fasten the additional pit extension to the main pit with at leasr 8 screws 3 5 Seal all joints and gaps with silicon paste or expansion foam so as to keep backfill out of the pit I O Access not supplied with kit Ground Level EF Pipe extension to above ground level not supplied with kit Approved
12. h valve Vacuum treaker a ae lat high points Grid type layout for gt sub surce lawns 1 supply manifold Manual flush valve A E 4 a Grid type layout for sub mulch garden beds Manual flush valve Flush manifold Mound mater TROUBLESHOOTING GUIDE oN y Normal Operating Sequence Controller LED light is off no power to the controller Controller LED light is on no water is detected Controller LED light is flashing and the pump is on water has been detected and the system is in operating mode The controller is connected to power and the LED light is off Potential Cause No power at power supply point Action Check power supply Potential Cause Fuse has blown Action Replace fuse you need a 3 15 amp slow blow fuse there are available at your local electronic store Potential Cause Controller is defective Action Contact your local Grey Flow supplier with proof of purchase The controller LED light is on water is running but the pump is off Potential Cause The plugs are still attached to the filters and do not allow the water to reach the sensor switch Action Unscrew and remove plugs from filter base and reinstall filters in their original location Potential Cause The filters are clogged Action Clean filters and reinstall filters in their original location 3 Potential Cause The sensor is
13. not connected Action Connect sensor wires 4 Potential Cause The air vent is closed or clogged Action Open up air vent tubing to air 5 Potential Cause The sensor is stuck in the open position debris can affect the operation of the sensor Action Pull out sensor from holding tee clean sensor and the inside of the tee and reinstall sensor in original position Potential Cause The sensor is defective Action Contact your local Grey Flow supplier with proof of purchase TROUBLESHOOTING GUIDE D The controller LED light is flashing but the pump is not running 1 Potential Cause The pump cables are not connected properly Action Connect pump wire properly 2 Potential Cause The impeller of the pump does not rotate large debris and hair can be the cause Action Remove pump from pit open casing and clear all debris and hair that may be stopping the impeller from turning Reinstall pump in its original position 3 Potential Cause The pump is defective Action Contact your local Grey Flow supplier with proof of purchase 4 Potential Cause The controller is defective Action Contact your local Grey Flow supplier with proof of purchase E The controller is operating normally all taps in the house are off but the pump is turning on and off on regular basis 1 Potential Cause There is a tap leaking in the house Action Check if water is flowing into the interceptor trap by looking into th
14. not suited to conditions where the invert level of the Grey Water pipe is lower than 2 feet below ground if lower than 2 feet use PS model instead The drip line must be kept 4 below mulch or soil check for Local State Municipal amp Council laws and regulations 110 volts power supply should be available PVC ABS plumbing parts to be installed by a license plumber Minimum garden area required applies REF TABLE 1 0 The Grey Flow 001 must be turned off during wet conditions and at any sign of accumulation or run off All set back distances for the irrigation system must be in accordance to the local regulations Number of Assumed uanuty af Minimum garden Recommended bedrooms in number of crey matey Soil Type area to irrigate in irrigation area in the house people Inthe ps Square Feet Square Feet house Gallons day Sand 90 2 3 75 Loam 130 230 amp 590 Clay 185 Sand 115 3 4 100 Loam 180 320 8 790 Clay 230 Sand 160 4 5 125 Loam 225 395 amp 1050 Clay 320 Sand 185 5 6 150 Loam 265 460 amp 1180 Clay 370 Sand 220 6 7 175 Loam 320 540 amp 1380 Clay 440 o MOLINA pater INSTALLAION PARTS LIST The Grey Flow 001 builder s Kits UP GF 001 BK are supplied with 1 Fully fitted Grey Flow 001 main pit with PVC interceptors and suction manifold 1 Extra holding bracket to be used only when additional extension is needed 1 Additional pit extensi
15. on 12 3 4 high supplied in 4 panels 2 6 screw in PVC caps 1 Reinforced plastic lockable lid 2 Filters with bottom screw plugs The Grey Flow 001 Finishing Kits UP GF 001 FK or UP GF 001 FK LP are supplied with 1 Oil cooled thermal protected submersible pump to be connected as a centrifugal pump 2 Assembled 1 check valves 1 Fully fitted float switch 1 Control box 2 Spare filters Grey Water Warning Sign 1 Corflute Grey Water warning sign to be visible at all time The Grey Flow Complete drip line irrigation Kits UP GF DL CK are supplied with 1 330 feet roll of purple drip line with integrated large flow 2 2 Gal Hr drippers 12 spacing 25 Drip line fittings 1 Punch tool 1 82 feet roll of 1 Low Density purple Polypipe with barb fittings to suit The following optional items are also available for purchase on line or through a retail store Approved Back Flow valve Grey Flow Self Cleaning Mechanism UP GF SCM helps reducing frequency of filter cleaning from once a month to once or twice a year depending on usage GF Rotor 6 stations UP GF RT6 allows for sequencial volumetric distribution of the Grey Water into more than one zone Grey Flow Station Drip line Kit UP GF DL SK for use in additional drip line stations Mound mater INSTALLAION PARTS LIST 1 Fully fitted Grey Flow 001 Builders Kit included dual interceptor with one set of capped filters and a PVC suction manifold
16. pipe using the 0 3 punch tool supplied The smallest end of the start connector is then inserted into the hole made in the polypipe 3 Connect to the start connectors the Grey Flow drip line and lay it above ground in one of the three layout models grid spiral or s curve Always keep the drip line as close to the plant as possible Leave the end of the drip line open 4 Stake the Grey Flow drip line to the ground every 3 4 5 Connect the end of the drip lines into a 1 Polypipe flush manifold 6 Insert a barbed flush valve into the flush manifold at its lowest point 7 Flush thoroughly the whole system by running tap water through you shower basin or trough 8 Cover the Grey Flow drip line with a minimum of 4 thickness of soil or mulch M MOLINA pater INSTALLATION STEP THREE Single zone dispersal system 1 2 vacuum breaker air bleed highest point if required g F 1 low density poly supply pipe fittings __1 low density y lil gt P poly flush pipe Drip Line Purple 2 2 Gal Hr i J 12 spacing l 1 P Punch a hole in the y poly using enclosed d L 1 4 punch tool J Maximum length 23 0 l y E 9 1 ratchet clippoly p B 1 end plug Ji 1 barbed manual flush valve Multiple zone dispersal system Grey Flow diverter Spiral type Layout for trees 1 mainline GF Rotor up to 6 stations 1 supply manifold WITTT TITT ye Manual O 9 A flus
17. supplied pump and filters have been sized to suit the full 330 feet supplied drip line flows and dripper sizes If non Grey Flow Drip line is used the warranty may be void o MOLINA pater INSTALLATION HA A Never leave the interceptor trap without filter 2 extra filters have been provided for instant replacement at cleaning time Make sure to insert the filters all the way down to the bottom of the interceptor trap the filter 1 2 riser should be standing vertically INSTALLATION STEP ONE Step Incoming water connections 1of3 Glue all PVC ABS joints Ground Level lt Pit extension Use 4 PVC ABS DWV pipe joiner for connections PVC ABS glue not included M MOLINA pater INSTALLATION STEP ONE Outgoing water connections Install approved Back flow valve I O Access Not supplied with Kit e Ground Level H Pipe extension to above ground level not supplied with kit m Approved Back flow valve not supplied with kit sai E afo eee eog sene ADI f to be purchased separately _ MM MOVING mater INSTALLATION STEP ONE Pit extension to ground level Cut the additional pit extension panels to size Assemble the panels and fit over the main pit Fasten the additional extension to the main pit using at least 8 screws Seal all joints and gaps with silicon or
18. with a garden hose or in any basin not connected to the dedicated grey water line C Open the lid of the secondary filter located in the underground pit remove lint filter and wash thoroughly with fresh water from the same source of water as in b D Flush thoroughly the whole system by running tap water through your shower basis or trough E The Grey Flow 001 System is ready to operate again The following maintenance steps should be carried out once a year A Remove and clean primary and secondary sponge filters B Re insert the filters filters may need replacing on an annual basis C Unscrew the sensor switch from its location on the suction of the pipe and rinse thoroughly ensure the system is turned off D Ensure that the sensor is still off and thoroughly flush the suction lines by pouring water through the filters Make sure to remove all debris and hair E Re insert and screw in sensor switch do not change the original positioning and direction of the sensor switch F Remove amp clean one way valves downstream of the pump G Turn on the pump and run water and a little chlorine through the entire system for at least five minutes H Top up mulch over the Grey Flow drip line to a minimum depth of 4 the Grey Flow Drip line will need to be replaced every 5 to 8 years ONE YEAR LIMITED WARRANTY AWWS USA LLC AWWS warrants this product against material defects in materials and workmanship for
Download Pdf Manuals
Related Search