282D - Xantech.com
Contents
1. 0o0 O S000 Ss 5000 000 Fig 3c amp d Emitter attached to shelf directly belo or above IR sensor window CAUTION Cabinet door locations Fig 3b will usually result in interruption of the IR control signals to the components when the door is open CONNECTING THE EMITTERS e Simply insert the mono mini plug of the 282D emitter into the EMITTERS or OUT jacks on any of the Xantech Connecting Blocks or Controllers e CAUTION DO NOT plug emitters into the IN OUT or HIGH OUT jacks on the 790 00 and 791 44 Connecting Blocks To do so will destroy the emitters 781 ERGPS Satelite Receiver To 120 VAC IR Sensor Unswitched Window 789 44 Lonnecting Glock See Emitter AV Receiver Ea lL Lis Emitter EQUIPMENT CABINET CLOSET ETC 223 7D SERIES IP Aeceiver iandiidu a nd He ie E Pemote Limited Warranty Xantech warrants its products to be free of defects in materials or workmanship This is a Limited Lifetime warranty from the date of purchase by the original consumer Any products returned to Xantech and found to be defective by Xantech within the warranty period will be repaired or replaced at Xantech s option at no charge Xantech will not be responsible for the actual cost of installation or removal of the product nor for any incidental or consequential damages Some states do not allow the exclusion or limitation of incidental or consequential damages so the a2. bove limitation may not apply to you This warranty gives you specific legal rights You may have additional legal rights that vary from state to state Xantech Corporation 13100 Telfair Ave 2F Sylmar CA 91342 Xantech com Installation Instructions 282D 2008 Xantech Corporation Document 08905166A This document is copyright protected No part of this manual may be copied or reproduced in any form without prior written consent from Xantech Corporation Xantech Corporation shall not be liable for operational technical or editorial errors omissions made in this document
3. dhesive layer for the best adhesion e The shell though dark in appearance is transparent to infrared light allowing commands from a handheld remote control to pass through it This permits direct control of the equipment from a handheld remote as well as from the 282D BLACK IR OPAQUE EMITTER SHIELD An optional shield available from Xantech as model 28DES fits over the emitter head and the sensor window of the controlled component It prevents unwanted external IR signals from passing through or leaking past it Adhesive Layer d Controlled Component Emitter Shield and Emitter installed Side View over IR sensor window Use the 28DES when you want the equipment to respond only to the 282D such as in zone controlled systems Top View ATTACHING THE EMITTERS TO OTHER LOCATIONS e The high output from the curved top side of the emitter permits control from as much as 3 feet away when on the axis of the IR sensor window of the component e This allows placement on surfaces just below above or in front of the controlled components for a more pleasing aesthetic appearance Choose a location on a cabinet shelf door etc as shown in Figs 3b c and d Be sure the edge of the component does not block the IR signal Figs 3c and d IR Sensor IR Controlled Components Window PA W Cabinet Door Fig 3a Emitter to IR sensor window Shelves directly opposite IR sensor window O oo
4. xantecn MODEL 282D Designer Emitter INSTALLATION INSTRUCTIONS ONNG2 777 3155 Cela DESCRIPTION The 282D Designer Emitter contains a tiny infrared LED housed ina miniature designer styled black appearing injection molded plastic shell It emits IR infrared control signals sent to it by IR receivers or other Xantech controllers The 282D can be installed directly on the IR sensor window of the controlled device or other suitable locations Side View y as NOTE White striped 44 side is positive 3 5mm mono i mini plug j Top View y io _ a 7 FT fe 3 FTA 5 8 INSTALLATION ATTACHING THE EMITTERS TO IR SENSOR WINDOWS e Each emitter has a clear adhesive layer on the bottom flat surface of the shell e Simply peel off the adhesive cover and affix the emitter to the center of the IR sensor window on the controlled component s front panel Internal IR Emitter High gt Low Output Output Side s A Side Emitter Shell Clear adhesive layer 4 Replace if necessary Mini wire with a short piece of the lead 2 sided tape supplied e In some cases it may be difficult to find the location of the IR sensor on the component Consult the owner s manual of the unit or the manufacturer for the exact IR sensor window location e Double sided adhesive tape is included If you move the emitter to a different component use this tape to replace the current a
Download Pdf Manuals
Related Search