ATA User`s manual
Contents
1. ano mack J B EEB _ 2 STEP 5 After setting up the parameters please browse to the Service gt IP PBX service menu and press RELOAD of IP PBX configuration reload selection for activating the settings IP PBX SERVICE IP PBX will re load configuration as soon as possible Currently active calls will be disconnected in 3 minutes Do you really want to Continue IP PBX Configuration Backup B PBX Settings Only IP PBX Configuration Restore RESTORE Device configurations on the ATA STEP 6 Please log in ATA via web browser browse to the SIP setting menu and select the Domain Service config menu In the setting page please browse to the Auto config page and enable the Auto Configuration features for IP PBX system 41 Auto Configuration Settings You could enable disable the auto configuration setting in this page Auto Configuration Oof TFP FIP OHTIP IP PBX TFIP Server HTTP Server FIP Server FTF Username FIP Password File Path STEP 7 After enabling the auto config feature the ATA shall be able to obtain IP address and SIP extension information from IP PBX system IPX 2000 information To verify the auto config results you may connect telephone set to ATA press 120 to check if the IP address is obtained from IPX 2000 And 122 can be used to verify the extension number assigned by IPX 2000 STEP 8 Repeat the same configuration steps on ATA B and check2. PLANET VoIP Analog Telephone Adapter VIP 156 VIP156PE VIP 157 VIP 157S Users manual Version 2 0 Copyright Copyright C 2006 PLANET Technology Corp All rights reserved The products and programs described in this User s Manual are licensed products of PLANET Technology This User s Manual contains proprietary information protected by copyright and this Users Manual and all accompanying hardware software and documentation are copyrighted No part of this User s Manual may be copied photocopied reproduced translated or reduced to any electronic medium or machine readable form by any means by electronic or mechanical Including photocopying recording or information storage and retrieval systems for any purpose other than the purchaser s personal use and without the prior express written permission of PLANET Technology Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsi
3. After time out the system will dial directly Dial Plan Settings You could set the dial plan in this page Replace prefix code On Oof Replace rule 001 006 009 E 008 Dial Plan aan xH tx420000000 Auto Prefix 02 i 0000 9999 Prefix Unset Flan 1402000000 Auto Dial Time 5 3 9 sec Symbol Explan Digits Description Solo ame 0 1 2 3 4 5 6 7 8 9 E Replace rule If replace prefix code function is ON and prefix number is matched with rule then 005 will replace prefix Auto Dial Time Stop dialing after seconds then send dial number out Dial Plan When match with pattern then send dial number out but if fisrt digit is O then dial plan will be ignored For Example Digits Description XX lf matched with one of 00 01 99 then will send number out If matched with one of 00 01 99 then will send number out If matched with one of 100 101 109 then will send number out If matched with one of 110 111 119 then will send number out 1 6 LLL LLL If dial with 8 digits then send number out Auto Prefix Number for add before dial number Prefix Unset Plan When first digit or dial numeb match with pattern then ignore auto prefix 24 Description lignore auto prefix if first digit is 0 f gnore auto prefix if first digit i is 1 dial numbers are 4 digits ignore auto prefix dial numbers are 5 digits ignore auto prefix When you fi
4. H T H Hee Ebel Lee Test the scenario 1 Pick up the telephone set on ATA A 2 Press the keypad 192 168 0 2 shall be able to connect to the ATA B 3 Then the phone in 192 168 0 2 should ring Please repeat the same dialing steps on ATA B to establish the first voice communication from ATA A 35 Case 2 Peer to Peer mode VIP 157S Port 1 to Port 2 communications Supposing one VIP 157S connects to two telephones just pick up phone 1 and dial 192 168 0 1 5062 phone 2 will ring Analog telephone sets are connected to the phone RuJ 11 ports of VIP 157S respectively 1001 192 168 0 1 1002 HWE HEE SOI Test the scenario 1 Pick up the telephone set on VIP 157S port 1 and you should be able to hear the dial tone 2 Press the keypad 192 168 0 1 5062 shall be able to connect to the VIP 157S port 2 3 Then the telephone set in VIP 157S port 2 should ring Please repeat the same dialing steps on port 2 to establish the first voice communication from VIP 157S Hint In default machine operation the VIP 157 is VoIP mode If you want to make a PSTN phone call press the 0O key to switch to PSTN mode If the IP address of the remote calling party is known you may directly make calls via its IP address and end with a If the ATAs are installed behind a NAT firewall IP sharing device for Peer to Peer VoIP application please make sure the NAT device support SIP applications and suit
5. Syne Time E Lo 0 dd hh mm Submit This page defines the Handset Volume Ringer Volume and the Handset Gain When you finished the setting please click the Submit button Handset Volume is to set the volume for you can hear from the handset Handset Gain is to set the volume send out to the other side s handset 21 Volume Setting You could set the volume of your phone in this page Handset Volume 10 0 12 Handset Gain 10 0 15 Volume Settings for VIP 156 VIP 156PE VIP 157S Beside the above settings VIP 157 also can set the volume of PSTN PSTN Out Volume is to set the PSTN volume for you can hear PSTN In Gain is to set the volume send out to the other side s handset Volume Setting You could set the volume of your phone in this page Handset Volume 10 0 12 PSTN Out Volume 10 L03 Handset Gain 10 0 15 PSTN In Gain 10 0 15 Submit Volume Settings for VIP 157 Block Setting This page defines the Block Setting to keep the phone slience You can choose Always Block or Block a period Always Block All incoming call will be blocked until disable this feature Block Period Set a time period and the phone will be blocked during the time period If the From time is large than the To time the Block time will from Day 1 to Day 2 When you finished the setting please click the Submit button Block Setting You could set the block period of your phone in t
6. no password to continue machine administration 12 Please locate your PC in the same network segment Note 192 168 0 x of ATA If you re not familiar with TCP IP please refer to related chapter on user s manual CD or consult your network administrator for proper network configurations LAN IP address configuration via web configuration interface Execute your web browser and insert the IP address default 192 168 0 1 of VIP in the adddress bar After logging on machine with username password default root no passwrd browse to Network gt Network settings configuration menu Network Settings You could configure your network settings in this page TCP IP Configuration IP Type Fixed IP O DHCF Client O PPPoE IP 192 168 0 1 Mask 255 255 255 0 Gateway 192 168 0 254 DNS Server 1 1168 95 11 DNS Server 2 168 95 192 1 MAC O0204faabboc Parameter Desc niption IP address LAN IP address of ATA Default 192 168 0 1 Subnet Mask LAN mask of ATA Default 255 255 255 0 Default Gateway Gateway of ATA Default 192 168 0 254 13 Network settings via Keypad commands The ATA series phone adapters support telephone keypad configurations please connect analog telephone set and refer to the following table for machine network configurations Machine operation Parameter s Notes ATA will change to DHCP IVR Menu Choice 111 Set DHCP client None Client Use the s
7. 1 FXS 1 FXO SIP Analog Telephone Adapter VIP 157S 2 port FXS SIP Analog Telephone Adapter VoIP Analog Telephone Adapter X X N Y Front Panel of VIP 156 Ce DC Left Right Panel of VIP 156 Front Panel of VIP 156PE iiy IC Left Right Panel of VIP 156PE FHOHE VoIP Analog Telephone Adapter ELD Front Panel of VIP 157 LINE iF C Dr Left Right Panel of VIP 157 VoIP Analog Telephone Adapter ELD Front Panel of VIP 157S E Fuis La Left Right Panel of VIP 157S RJ 45 connector for Internet access connected directly to Switch Hub through straight CAT 5 cable The LAN interface also can be connected with 802 3af PoE switch or converter for power supply VIP 156PE EA D E 12V DC Power input outlet Reset Reset to the factory default setting Machine default IP is http 192 168 0 1 Press RESET L Note button on rear panel over 5 seconds will reset the VoIP Phone Adapter to factory default value Except speed dial and call forward settings 10 LED display of VIP 156 VIP 156PE Power is supplied to the device The Status LED will be flashing when the machine is operational OFF the device is connected to LAN at 10Mb s OFF the phone is idle ON the phone is in use offhook Blinking the phone is ringing LED display of VIP 157 VIP 157S STATUS The Status LED will be flashing when the machine is operational OFF the device is conne
8. auto answer in this page Auto Answer On Cor Auto Answer Counter 03 2 15 FIN Code Enabled O On OOF PIN Code aa o Test the scenario 1 2 3 4 5 6 VIP 156_C pick up the telephone Dial the IP Address 192 168 0 1 VIP 157_A VIP 157_A will ring up but doesn t answer the call After 3 rings the VIP 156_C will hear the prompt sounds then input the password 123 VIP 156_C will hear the dial tone from PSTN line then input Phone Number 11112222 The Phone Number 11112222 will ring up then it pick up the telephone and communication with the VIP 156_C 51 Case 10 Auto Answer Feature_PSTN to IP In this example there are one VIP 157 and two VIP 156 and connect with Peer to Peer mode The VIP 157_Ahad set Auto Answer function for forwarding to arbitrary telephone If there have incoming PSTN calls and VIP 157_A doesn t answer the incoming calls after specific time the caller will hear prompt sounds to input the password and then dial out an arbitrary IP telephone fo witch Intranet ooo ooo 197 168 02 192 168 0 3 l 192 168 0 1 Phone Number LAN 3311 1424 VIP 157_A VIP 156_ B VIP 156 C Enabled Auto Answer Function Z Phone Number 1111 2222 Machine configuration on the VIP 157 STEP 1 Please log in VIP 157_A via web browser browse to the Phone Settings menu and select the Auto Answer config menu In the setting page please enable the Auto Answer and PIN Code Enabled function and then
9. if the ATA B is successfully registered with the IPX 2000 as one of the IP extensions Test the scenario 1 Pick up the telephone on ATA A 2 Press the keypad 1001 shall be able to connect to the ATA B 3 Then the telephone set in ATA B should ring Please repeat the same dialing steps on ATA B to establish the first voice communication from ATA A 42 Case 5 Call Forward Feature_Example 1 In the following samples we ll introduce the Call Forward Feature applications In this example there are three VIP 156 register to SIP 50 and VIP 156_ A had set Call Forward function to VIP 156_B SIP 30 ree LAN LAN s 197 168 0 1 i 197 168 0 2 192 168 0 3 VIP 156_A VIP 156_ B VIP 156_C Line number forward Line number Line number 1001 2002 3003 Machine configuration on the VIP 156 Please log in VIP 156_A via web browser browse to the Phone Settings menu and select the Call Forward config menu In the setting page please enable the All Forward function and fill in the Name and URL of VIP 156_B then the sample configuration screen is shown below Forward Setting You could set the forward number of your phone in this page All Forward Off On Busy Forward Of On No Answer Forward Of n All Fwd Ho VIP 156_B 2002 viP 456 B 2002 o Busy Fwd Mo No Answer Fwd Mo l No Answer Fwd Time Out 3 2 8 Ring 43 Test the scenario 1 VIP 156 C pick up the telephone 2 Dial the
10. number 1001 VIP 156_A 3 Because VIP 156_A had set up All Forward function to the number 2002 VIP 156_B 4 The number 2002 VIP 156_B will ring up then it pick up the telephone and communication with the number 3003 VIP 156_ C 44 Case 6 Call Forward Feature_Example 2 In this example there are one VIP 157 and two VIP 156 register to SIP 50 The VIP 157_A had set Call Forward function to phone number 1111 2222 PSTN SIP 50 J p kR WAN 192 168 0 50 L A YA A ml UHE 192 168 0 1 192 168 0 2 192 168 0 3 LAN LAN YIP 157_A VIP 156_B VIP 156_C l Line number Line number Line number as gO 4001 2002 3003 CS Phone Number 1111 2222 Machine configuration on the VIP 157 Please log in VIP 157_A via web browser browse to the Phone Settings menu and select the Call Forward config menu In the setting page please select the All Forward function to PSTN choice and fill in the Name and URL Number of PSTN Phone Number 11112222 then the sample configuration screen is shown below 45 Forward Setting You could set the forward number of your phone in this page All Forward OOF OIP PSTN Busy Forward Of GIP No Answer Forward LOOP OIP OPSTN All Fwd No Pot 11112222 LE Busy Fwd No No Answer Fwd No m L 1 iy l No Answer Fwd Time Out Ei 3 3 ipe Ring Test the scenario 1 2 3 VIP 156_C pick up the telephone Dial the number 1001 VIP 1
11. the sample configuration screen is shown below Auto Answer You could enable disable the auto answer in this page Auto Answer On Oof Auto Answer Counter U2 2 15 PIN Code Enabled On OOF PIN Code 123 STEP 2 Please log in VIP 157_A via web browser browse to the Phone Book menu and select the Speed Dial Settings config menu In the setting page please add a speed dial number for dial to IP address 192 168 0 2 VIP 156_B and then the sample configuration screen is shown below 52 Speed Dial Phone List You could set the speed dial phones in this page Phone Name T URL Select 0 VIP 156 DB 192 168 0 2 L 3 2 3 A 5 6 T a 9 Delete Selected Delete All Test the scenario 1 2 3 The Phone Number 11112222 pick up the telephone Dial the PSTN Phone Number 33334444 VIP 157_A VIP 157_A will ring up but doesn t answer the call After 3 rings the Phone Number 11112222 will hear the prompt sounds then input the password 123 The Phone Number 11112222 will hear the dial tone then input O The IP address 192 168 0 2 VIP 156_B will ring up then it pick up the telephone and communication with the Phone Number 11112222 53 Appendix B VIP 156 VIP 156PE VIP 157 VIP 157S Specifications SIP Analog Telephone Adapter Model VIP 156 VIP 156PE VIP 157 VIP 157S Hardware 1 x 10 100Mbps Ru 45 port 802 3af PoE for VIP 156PE 1 x 10 100Mbps Ru 45 port FXS for telephone set 1 x RJ 11 2 x R
12. 57_A Because VIP 157_ Ahad set up All Forward function to the PSTN Phone Number 11112222 The PSTN Phone Number 11112222 will ring up then it pick up the telephone and communication with the number 3003 VIP 156_C 46 Case 7 Call Forward Feature_Example 3 In this example there are one VIP 157 and two VIP 156 register to SIP 50 The VIP 157_A had set Call Forward function to number 2002 VIP 156_B SIP 50 192 168 0 50 _ Switch Intranet 192 168 0 1 Phone Number LAN 3515 4444 VIP 157_A VIP 156_B VIP 156_C LINE number Forward Line number Line number a 1001 2002 3003 Phone Number 1111 2222 Machine configuration on the VIP 157 Please log in VIP 157_A via web browser browse to the Phone Settings menu and select the Call Forward config menu In the setting page please select the All Forward function to IP choice and fill in the Name and URL Number of of VIP 156_B and then the sample configuration screen is shown below 47 Forward Setting You could set the forward number of your phone in this page All Forward OOP IP OPSTN Busy Forward Of QIP No Answer Forward DOF OIP PSTN es er ee All Fwd No VIP 156 B 2002 Busy Fwd No a 7 No Answer Fwd No i No Answer Fwd Time Out 3 2 8 Ring Test the scenario 1 2 3 PSTN Phone Number 11112222 pick up the telephone Dial the PSTN Phone Number 33334444 VIP 157_A Bec
13. IP_ATAV2 Table of Contents Chapter ceivesss cskca dtc renee eN REEI ETENEE EAE IEEE ARA 6 TSR Ta T T 6 LGG H A EAEE ESA O E 6 Packo R icici cadcecsuestnseesccs des cecesaonscacsaaa suas udaasaseouscucauues sends EEE EEES EEEE a 7 Physical Details eonia cusses cetewcedecteceus sre cewsssveneuseavevcuccececaueuussteuseruacsuuueteweecssteneusserstenn E O E 7 EED Display T TT 10 Chapter 2 Preparations amp Installation sssssssssceeeeccccccccocssssssseseccccccecososossssssssscssscececesssssso 12 Physical Installation Requirement eeeeccceccccsssssseecccceccecocccssssssecccecoccoccccsossssessceccccecccssssssssssseceeeceesssoss 12 LAN IP address configuration via web configuration interface sse eee eee 13 Chapter 3 Network Service Configurations ssssssssceeeccccssssseceoccosssssccecoccossssccecocssssssseeeosso 17 Configuring and monitoring your Phone Adapter from web rowSser ssssssssssssssssssssssssssssssssseees 17 Overview on the webanterlace Of ATA iuro aenea EEE EEEE EE E e 17 Manipulation of ATA via web eS TT 17 Chapter 4 VoIP Telephone Adapter ConauratiOnS ssssssssssssssssssssssssssssssssssssssssssssssssssssssss 19 Speed Dial SCM ae a E a E E E TT 19 Call STR C RTT E T ET 20 DINED S CULTS ienr E a hongowsesuauapsirvandaeeanimamecbansa eimantcanbenmadetbesaugausanes 21 VON ies Oe Ee 1a 1 A E RER EIA EN PERITE E ETEA E ET E E EE TEA EE PEATE E EETA ATT 21 BOCK en TTT 22 AIO Als wer FOr VLE SIS TT
14. J 11 connection FXO PSTN connection KR Standard SIP 2 0 RFC3261 SIP Outbound proxy STUN RFC 3489 G 723 1 6 3k 5 3k G 729A G 729B G 711 Fax support T 38 Voice Standard Voice activity detection VAD Comfort noise generation CNG Acoustic echo canceller AEC G 165 Line echo canceller LEC Jitter Buffer Protocols SIP 2 0 RFC 3261 TCP IP UDP RTP RTCP HTTP ICMP ARP DNS DHCP NTP SNTP PPP PPPoE Network and Configuration Static IP PPPoE DHCP Web keypad 0 40 degree C 10 95 humidity EMC EMI CE FCC Class B 54
15. M and browse to the firmware location c Please find the firmware decompress and find the rom file for upgrade d After firmware loaded the unit will be reboot and loaded with factory default values e Default IP address of the customized firmware http 192 168 0 1 login name password root null no password Reset to Default In Default Setting you can restore the Phone Adapter to factory default in this page You can just click the Restore button then the Phone Adapter will restore to default and automatically restart again Reset to Default You could click the restore button to restore the factory settings Reset to default 33 Reboot without saving Reboot function you can restart the Phone Adapter If you want to restart the Phone Adapter you can just click the Reboot button then the Phone Adapter will automatically Reboot without Saving You could press the reboot button to restart the system Reboot without Saving 34 Appendix A Voice Communication Samples There are several ways to make calls to desired destination in ATA In this section we ll lead you step by step to establish your first voice communication via keypad and web browsers operations Case 1 ATA to ATA connection via IP address Assume there are two ATAS in the network the IP address are 192 168 0 1 192 168 0 2 Analog telephone sets are connected to the phone RJ 11 port of ATAS respectively 192 168 0 1 192 168 0 2 2
16. T 23 Caler SG TTT 23 PTB a Tee er tage ecient el aan ean ot cease tetas set een os As tae on ete estate Caan a bideuteie entre nense lle teiedats 24 Plash TME ET TT 25 Cal Walne erT 25 Too PAA OE LUMO e E i naaaieursenantank aenautabne soaugeviooaueanennes 26 PONS Ml TTT 26 SElVICS Doman Se MNE oee ee A r e a a E rE E EEE 2d Port SEINS ineei E E E E N 28 RSI o UGS Annaa ar a a N E A tan shin tentansaeteeaes 28 Codec ID Se T TTT 28 DTME SCUD aeir a E E E E E EOT 29 RPO SeN sanee a E e ET 29 OEEO S eee a E EE EA 30 SITI L A N N 30 AMO COMM OE AL OF TTT 30 ICMP Se Uh TTT 31 FEES NE cone naseumtinacsa Pade wacsant E E T E E I E A A 31 SYS EMAD err E E E EEE A EEE E E 32 SVEA I A A 32 PETA AS e TTT TTT 32 Res tto DE EMI aonair EE E E enn dedee soreness sueqedeceutyenseeandedesseuentesee 33 G TITI a oee a A al Aal A A A 34 Appendix A Voice Communication Samples cccccccccccccccccccccccccccscsccccccccecsccscccscsccscscsscscscsccsseees 35 Case 1 ATA to ATA connection via IP address asea cniin aiit aT ORO aaa 719 35 Case 2 Peer to Peer mode VIP 157S Port 1 to Port 2 communications sss eee eee eee ee 36 Case 3 Voice communication via SIP proxy server SIP 50 e 37 Case 4 Voice communication via IP PBX system IPX 2000 Auto config cc ceeeseeeeeeeeeeeeeees 39 Case 5 Call Forward Feature Ex ample TT 43 Case 0 Cal Forward Feature Example TT 45 Case 7 Call Forward Feature_Example 3 sssss sese ee
17. able settings should be applied to the NAT device to enable the SIP communications before making calls VIP 157S in PLANET ATA series products to connect to remote ATA press the keypad in the following sequence to connect to the remote VIP 157S port 2 remote ATA IP address 5062 for example 192 168 0 2 5062 36 Case 3 Voice communication via SIP proxy server SIP 50 Registration Registration Authentication SIP 50 Authentication Ss Pot oo SIP 50 IP Address 192 168 0 50 ATA A IP Address 192 168 0 1 m ATA B IP Address 192 168 0 2 Line Number 1001 Line Number 2002 Device configurations on the ATA STEP 1 Log in SIP 50 and create two testing accounts password 1001 123 for ATA A and 1002 123 for ATA B for the voice calls STEP 2 Please log in ATA via web browser browse to the SIP setting menu and select the Domain Service config menu In the setting page please insert the account password information obtained from your service provider in this sample were using PLANET SIP 50 as the SIP Proxy server for SIP account call authentications and then the sample configuration screen is shown below Service Domain Settings You could set information of service domains in this page Realm 1 Default Active LO On OoOf Display Name 1001 Line Number 1001 Register Name planet Register Password eee Domain Server 192 166 0 50 Proxy Server 192 166 0 50 Outbound Prox
18. an be used to display the network settings enabled on ATA via voice prompt IVR Menu Choice Machine operation Check IP Address Check network connection Type Check the Phone Number Check Network Mask Check Gateway IP Address Check Primary DNS Server Setting Check Firmware Version Notes IVR will announce the current IP address of the ATA IVR will announce if DHCP in enabled or disabled IVR will announce current enabled VoIP number IVR will announce the current network mask of the ATA IVR will announce the current gateway IP address of the ATA IVR will announce the current setting in the Primary DNS field IVR will announce the version of the firmware running on the ATA Please contact your Internet service provider to obtain the Hint Internet access type and select the proper network settings in ATA to establish the network connections 15 After confirming the modification you ve done Please click on the Submit button to apply settings and browse to Save amp Reboot menu to reboot the machine to make the settings effective Connection Type Data required In most circumstances it is no need to configure the DHCP Fixed IP settings DHCP clinet The ISP will assign IP Address and related information The ISP will assign PPPoE username password for Internet PPPoE access Please consult your ISP personnel to obtain proper PPPoE IP address related information and input ca
19. ause VIP 157_A had set up All Forward function to the number 2002 VIP 156_B The number 2002 VIP 156_B will ring up then it pick up the telephone and communication with the PSTN Phone Number 11112222 48 Case 8 Call Forward Feature_Example 4 In this example there are three VIP 156 and connect with Peer to Peer mode VIP 156_A had set Call Forward function to VIP 156_B VIP 156 A VIP 156 H VIP 156_C Machine configuration on the VIP 156 Please log in VIP 156_A via web browser browse to the Phone Settings menu and select the Call Forward config menu In the setting page please enable the All Forward function and fill in the Name and URL of VIP 156_B and then the sample configuration screen is shown below Forward Setting You could set the forward number of your phone in this page All Forward Cor dOn Busy Forward Of On No Answer Forward Of Oon All Fwd No VIP456B 192 168 02 Busy Fwd No No Answer Fwd Mo l No Answer Fwd Time Out 3 2 8 Ring Test the scenario 1 VIP 156 C pick up the telephone 2 Dial the IP Address 192 168 0 1 VIP 156_ A 3 Because VIP 156 Ahad set up All Forward function to the IP Address 192 168 0 2 VIP 156_B 4 The IP Address 192 168 0 2 VIP 156_B will ring up then it pick up the telephone and communication with the VIP 156 C 49 Case 9 Auto Answer Feature 1P to PSTN In this example there are one VIP 157 and two VIP 156 and connec
20. bility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions CE mark Warning The is a class B device In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures WEEE Warning ae To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Trademarks The PLANET logo is a trademark of PLANET Technology This documentation may refer to numerous hardware and software products by their trade names In most if not all cases their respective companies claim these designations as trademarks or registered trademarks Revision Users Manual for PLANET VoIP Analog Telephone Adapter Model VIP 156 VIP 156PE VIP 157 VIP 57S Rev 2 0 November 2006 Part No EM V
21. cted to LAN at 10Mb s ON the device is connected to LAN at 100Mb s OFF the phone is idle ON the phone is in use offhook LNK ACT Blinking the phone is ringing OFF the phone is idle ON the phone is in use offhook Blinking the phone is ringing 11 Chapter 2 Preparations amp Installation Physical Installation Requirement This chapter illustrates basic installation of ATA analog Phone Adapter ATA in the following term e Network cables Use standard 10 100BaseT network UTP cables with RJ45 connectors e TCP IP protocol must be installed on all PCs For Internet Access an Internet Access account with an ISP and either of a DSL or Cable modem Administration Interface PLANET ATA provides GUI Web based Graphical User Interface for machine management and administration Web configuration access To start ATA web configuration you must have one of these web browsers installed on computer for management 6 Microsoft Internet Explorer 4 01 or higher with Java support Default LAN interface IP address of ATA is 192 168 0 1 You may now open your web browser and insert http 192 168 0 1 in the address bar of web browser to logon ATA web configuration page Enter Network Password Please type your user name and password VoIP Phone Adapter Configuration passwords Save this password in your password list ATA will prompt for logon username password please enter root null
22. d Domain Server you need to input the Register Password get from your ISP you need to input the Domain Server get from your ISP you need to input the Proxy Server get from your ISP you need to input the Outbound Proxy get from your ISP If your ISP you need to input the Register Name get from your ISP Proxy Server Outbound Proxy o does not provide the information then you can skip this item You can see the Register Status in the Status item If the item shows Registered then your Phone Adapter is registered to the ISP you can make a phone call direcly If you have more than one SIP account you can following the steps to register to the other ISP When you finished the setting please click the Submit button Service Domain Settings You could s information of sernice domains im this page Realm 1 Default Lave Number 1001 Register Name Repti Password Domain Sree 27 Port Setting This page defines the SIP and RTP port number in this page Each ISP provider will have different SIP RTPport setting please refer to the ISP to setup the port number correctly When you finished the setting please click the Submit button Port Settings You could set the port number in this page SIP Port 5060 1024 65635 RTP Port 60000 1024 55535 Codec Settings This page defines the Codec priority RTP packet length and VAD function in this page You need to follow the ISP suggestion to setup the
23. e 47 Case S Call Forward Feature Example TT 49 Case 9 Aulo Answer Feature IP10 PS Nenna E E E EEA 50 Case LO Autownswer Feature PSTN to IP arraiaren ea E O E ETARA 52 Appendix B VIP 156 VIP 156PE VIP 157 VIP 157S Specifications ccccccccccsscscssssscsssscsssscsssesssees 54 Chapter 1 Introduction Overview Based on years of VoIP manufacturing experiences PLANET Technology VolP total solutions are known for advanced implementation of standards based telephony with mass deployment capability Cost effective easy to install and simple to use the PLANET VIP 156 VIP 157 VIP 157S VoIP Phone Adapter ATA in the following term converts standard telephones to IP based networks The service providers and enterprises offer users traditional and enhanced the telephony communication services via the existing broadband connection to the Internet or corporation network With the ATA home users and companies are able to save the installation cost and extend their past investments in telephones conference and speakerphones The ATA can be the bridge between traditional analog systems and IP network with an extremely affordable investment The ATA includes two alternatively Ethernet interface for Internet PPPoE DHCP or Fixed IP or office LAN connection With adding the auto provision feature of our IP PBX product IPX 2000 the ATA can be seamlessly integrated into the telephony network and be used in consumer and busine
24. e EDIT button for set up the Auto Config configuration DEVICE PHONE MANAGEMENT Device ID Device Administration URL S Associated Device ID Device Administration URL Auto Cent Conf Extension STEP 3 Please fill out the Vendor Prefix code and MAC Address of ATA E nable Autom ati L C li ent Configu rati on Device auto dew vip156_ Vanop is O eoan T 0 0 Je Je leja Supplementary Configuration Lite SEE awe Ast EA i E 2nd codec mm 2nd packet ime oD Ser 709 w 30 i 3rd packet time E Enable Voice Acti i y Detection VAD DTMF Mode fiand 99 Note The following are the Vendor Prefix of devices 1 VIP 156 pla156 2 VIP 157 VIP 157S pla157 STEP 4 Please browse to the Device gt Extension of IP Phone menu to create the two extension accounts password 1001 123 for ATA A and 1002 123 for ATA B for the voice calls 40 EXTENSION MANAGEMENT Brenson uber o Associated Device anto_dev_vipl56 w Password eee User Pickup Group L ne Type Voi cemail Voicemail PIN
25. e name and the phone number by URL type When you finished a new phone list just click the Add Phone button If you want to delete a phone number you can select the phone number you want to delete then click Delete Selected button If you want to delete all phone numbers you can click Delete All button Speed Dial Phone List You could set the speed dial phones in this page Phone Name URL Select U 2 a 4 z b 7 D z Delete Selected Delete All Add New Phone Position l o 9 Marne URL 19 Call Forward Setting This page defines Call Forward function You can setup the phone number you want to forward in this page There are three type of Forward mode You can choose All Forward Busy Forward and No Answer Forward by click the icon All incoming call will forward to the number you chosen You can input the name and the phone number in URL field If you select this All Forward function then all the incoming call will direct forward to the speed dial number you choose If you are on the phone the new incoming call will forward to the Busy Forward number you choosed You can input the name and the phone number in URL field l If you can not answer the phone the incoming call will forward to the number you chosen You can input the name and the phone number in No Answer Forward URL field Also you have to set the Time Out time for system to start to forward the call to the
26. g This page defines the RPort Enable Disable in this page To change this setting please following your ISP information When you finished the setting please click the Submit button RPort Settings You could enable disable the RPort setting in this page RFort DOn On Submit 29 Other Setting This page defines the Hold by RFC Voice SIP QoS and SIP expire time in this page To change these settings please following your ISP information When you finished the setting please click the Submit button The QoS setting is to set the voice packets priority If you set the value higher than 0 then the voice packets will get the higher priority to the Internet But the QoS function still need to cooperate with the others Internet devices Other Settings You could tat bar settings mi this page Hold by BEC On Odi Worth Wis 40 83 Sl Uor An 53 SIP Eupr mp FA AO sec Sumi Riegel C STUN Setting This page defines the STUN Enable Disable and STUN Server IP address in this page This function can help your Phone Adapter working properly behind NAT To change these settings please following your ISP information When you finished the setting please click the Submit button STUN Settings You could set the IF of STUH server in this page STUHE L 71 On oOf STUN 2266 STUN Port 1024645535 l Subm bard Auto Configuration This page defines the Auto Configuration Auto Provision setti
27. his page Always Block Con Of Block Period Oon LS O From HOC hb rnr To I 00 bmi T Ea Auto Answer For VIP 157 This page defines the Auto Answer function You can set the Auto Answer function to answer the incoming call by the phone If the call is come from the IP then the VIP 157 can let user to redial the call to PSTN phone number If the call is coming from PSTN then the VIP 157 can let user to redial to IP Phone number Auto Answer Counter is to set after the ring count met the number you set then the auto answer will enable For security issue you d better to set the PIN Code If you have set the PIN code you will hear a tone to inform you input the PIN Code then you can dial out Auto Answer You could enable disable the auto answer in this page Auto Answer On Of Auto Answer Counter 2 15 PIN Code Enabled On Of PIN Code Caller ID Setting This page defines the device to show Caller ID in your PSTN Phone or IP Phone There are four selection of Caller ID You need to base on your environment to set the Caller ID function for FSK or DTMF Caller ID Setting You could enable disable the caller ID setting in this page Caller ID Dont show caller ID v Single Caller ID Ov es No CID Without Time OYes LONG 23 Dial Plan Setting This page defines the Dial Plan Setting function This function is when you input the phone number by the keypad but you don t need to press
28. n het page Usemame roc Hew password Confined patiwied Save amp Reboot In Save amp Reboot you can save the changes you have done If you want to use new setting in the Phone Adapter You have to click the Save button After you click the Save button the Phone Adapter will automatically restart and the new setting will effect Save amp Reboot You have to save changes to effect them save Changes Firmware Upgrade In Firmware Upgrade function you can update new firmware via HTTP in this page You can ugrade the firmware by the following steps Select the firmware code type AP or DSP code Click the Browse button in the right side of the File Location or you can type the correct path and the 32 filename in File Location blank Select the correct file you want to download to the Phone Adapter then click the Update button Firmware Upgrade You Gould wodate the fies Brent Code Type WAP DSP File Lor tinn Browse Uppdal Rosea Note For technological consideration we ve strongly suggested refering to the following upgrade methods for update your IP Phone Firmware Upgrade methods Please find the firmware of IP Phone and be sure to check the firmware upgrade steps to load the firmware into machine properly for revolutions a Log in IP Phone via Microsoft Internet explorer web browser and insert http ATA s IP address update htm in the address bar b Select update All RO
29. ng ATA supports TFTP FTP HTTP and IP PBX auto configuration function in total In IP PBX Auto Configuration Setting you need to check with your service provider if they have provided this function Usually this function will be boundle with an IP PBX to use in the office 30 Auto Configuration Settings You could enablatdisable the auto configuration Setting in thes page Auto Condiquration Se OTF OFF O RTP OPPeax TFTP Serme ATIP Sarwar FIP Server FTF Utema FTF Password File Path Subm Reset Rese ICMP Setting This function can disable echo when someone ping this device it can avoid haker try to attack the device When you finished the setting please click the Submit button ICMP Setting You could enable disable the ICMP setting in this page ICMP Not Echo O On off PTT Setting In PTT Settings is for you to set the Country different country will have different settings in FXS inter face PTT Setting You could select the PTT setting for diferent country in this page SLIC PTT USA PTT Settings for VIP 156 VIP 157S 31 Beside the above settings VIP 157 also can set country of FXO port PTT Setting You could select the PTT setting for different country in this page PSTN PTT USA SLIC PTT USA v PTT Settings for VIP 157 System Authority In System Authority you can change your login password System Authority You could change the login username passord m
30. nished the setting please click the Submit button Flash Time Setting When you use the PSTN Phone and you need to press the Hook to do the Flash Switch to the other phone line or HOLD this function is for you to set the time you press the Hook to represent the Flash function Flash Time Setting You could set the flash time in this page Max Flash Time 60 Range 4 255 Unit 10ms Flash Time Settings for VIP 156 VIP 156PT VIP 157S Beside the above settings VIP 157 also can set the flash time of FXO port Flash Time Setting You could set the flash time in this page FAO Flash Time Flash Time 5 3 200 1 gt 10ms SLIC Flash Time Max Flash Time 60 4 255 1 gt 10ms Flash Time Settings for VIP 157 Call Waiting Setting When you are talking with other people You can choose If you want to hear the notice when there is a new coming call If the call waiting function is On if there is a new incomeing call you will hear the call waiting notice in your current call If you set the function to Off then you will not hear any notice 25 Call Waiting Settings You could enablefdisable the call waiting setting in this page Call Waiting On Of Reset T 38 FAX Setting This page defines the T 38 FAX setting function You can Enable Disable the T 38 function and can modify the T 38 transmission port of each FXS port T 38 FAX Setting You could enable disable the FAX function in thi
31. number you choosed When you finished the setting please click the Submit button Note When you finished the setting please click the Submit button Forward Settings You could set the forward number of your phone in this page All Forward Oof OoOn Busy Forward Oof On No Answer Forward Qof Oon T nE HR All Fwd No cc llr No Answer Fwd Time Out 2 8 Ring Call Forward function for VIP 156 VIP 156PT VIP 157S Call Forward to PSTN VIP 157 VIP 157 not only supports Call Forward to IP calls but also can forward the calls to PSTN You can choose the Call Forward type with PSTN and then input the name and the PSTN number in URL Number field 20 SNTP Setting Forward Settings You could set the forward number of your phone in this page All Forward Gof OIP OPSTN Busy Forward OOP OIP No Answer Forward Sof OIP OPSTN All Fwd No Busy Fwd Np No Answer Fwd Ho No Answer Fwd Time Out 3 2 8 Ring Call Forward function for VIP 157 This page defines the primary and second SNTP Server IP Address to get the date time information Also you can base on your location to set the Time Zone and how long need to synchronize again When you finished the setting please click the Submit button Volume Setting SNTP Settings You could set the SNTP servers in this page SNTP G Dn Oof Primary server 19242 244 19 secondary Server 208 184 49 9 Time Zone GMT v 08 YL UC Y thhimm
32. on of ATA via web browser Log on ATA via web browser After TCP IP configurations on your PC you may now open your web browser and input http 192 168 0 1 to logon Phone Adapter web configuration page Phone Adapter will prompt for logon username password root null no password Enter Network Password Please type your user name and password VoIP Phone Adapter Configuration password Save this password in your password list ATA log in page 17 When users login the web page users can see the Phone Adapter system information like firmware version company etc in this main page PLANET Naiwaiirg amp Cemenaricati o System Information This page illustrate the system related information Phone Book Company PLANET Techn ology Corp Firmware Version 2 0 Phone Setting Codec Version 10 ee i Contact Ada lei i 96 Min Chuan Road Hsin Tien Taipei Taiwan Tel 886 2 22199518 SIP Settings Fax po0 2 22 199525 S E Mail support_voip planet com tw NAT Trans Web Site www planet com tw Adwanced Settings System Auth Save amp Reboot System Settings Reboot without Saving VoIP Phone Adatper main page 18 Chapter 4 VoIP Telephone Adapter Configurations Speed Dial Setting In Speed Dial setting function you can add delete Speed Dial number You can input maximum 10 entries speed dial list If you need to add a phone number into the Speed Dial list you need to input the position th
33. refully Hint If Internet connection cannot be established please check the physical connection or contact the ISP service staff for support information Save Modification to Hash Memory Most of the VoIP router parameters will take effective after modifications but it is just temporary stored on RAM only it will disappear after your reboot or power off the VolP Phone Adapter to save the parameters into Flash ROM and let it take effective forever please remember to press the Save amp Reboot button after you modify the parameters Save amp Reboot You have to save changes to effect them save Changes 16 Chapter 2 Network Service Configurations Configuring and monitoring your Phone Adapter from web browser The ATA integrates a web based graphical user interface that can cover most configurations and machine status monitoring Via standard web browser you can configure and check machine status from anywhere around the world Overview on the web interface of ATA With web graphical user interface you may have More comprehensive setting feels than traditional command line interface Provides user input data fields check boxes and for changing machine configuration settings Displays machine running configuration To start ATA web configuration you must have one of these web browsers installed on computer for management Microsoft Internet Explorer 4 01 or higher with Java support Manipulati
34. s page T 38 FAX Con ot T 38 Port 61000 1024 65533 T 38 FAX Settings for VIP 156 VIP 156PE VIP 157 T 38 FAX Setting You could enable disable the FAX function in this page T 38 FAX OOO OOP T 38 Port of Phonet 61000 1924 65533 7 36 Part of Phone 61100 1024 65533 T 38 FAX Settings for VIP 157S DDNS Setting This page defines the DDNS setting in this page You need to have the DDNS account and input the informations properly You can have a DDNS account with a public IP address then others can call you via the DDNS account But now most of the VoIP applications are work with a SIP Proxy Server When you finished the setting please click the Submit button 26 DDNS Settings You could gel the comiquraien of COONS in thee page DUNS C3 Dn cH Hasi Maree User Name a Password Emid Addas Type BACKME Dn QB Service Domain Setting In Service Domain Function you need to input the account and the related informations in this page please refer to your ISP provider You can register three SIP account in the ATA You can dial the VoIP phone to your friends via first enable SIP account and receive the phone from these three SIP accounis First you need click Active to enable the Service Domain then you can input the following items Display Name you can input the name you want to display Line number you need to input the User Name get from your ISP Register Name Register Passwor
35. se items When you finished the setting please click the Submit button Codec Settings You could set the codec settings in this page Codec Preanty 1 Gr ka Codec Pronty 2 G 753 Codec Prisnty 3 G711 uae Codec Pronty 4 Fil alse Codet Pronty B Gi 16 Codec Fronty B Gira 44 M Codec Frenty F GT 37 N Codec Pranty 6 Graa 4 Y RIP Packet Length B711 amp Gra A rns Gres Din F G23 5 3K On 2709 Wolica VAD Woite VAD 1 3 Uie 157 Oe Submit Reset Codec ID Setting This page defines the Codec ID Sometimes 2 VoIP devices with different Codec ID will cause the interopability issue If you are talking with others got some problems you may ask the other one what kind of Codec ID he use and then you can change your Codec ID When you finished the setting please click the Submit button 28 Codec ID Setting You could set the value of Codec ID in this page Codec Type JID Default Value G726 16 ID 23 95 255 23 726 24 ID 22 g5 p65 22 G726 32 ID 2 95 255 2 G726 40 ID a EE 21 RFC 2833 ID 101 96 266 407 DTMF Setting This page defines the RFC2833 Out Band DTMF Inband DTMF and Send DTMF SIP Info in this page To change this setting please following your ISP information When you finished the setting please click the Submit button DTMF Settings You could set the DIMPF Settings in this page 2833 O Inband DTMEF O Send DTMF SIP Info RPort Settin
36. ss IP telephony service no expertise required The ATA and our IP PBX system integration are the ideal combination for your office daily communications Product Features e Feature rich telephone service over home or office Internet Intranet connection e Auto config feature for flexible ease of use IP PBX system integration e Cost effective field proven compatibility and stability e Web based and telephone keypad machine configuration e Remote machine administration authentication e Voice prompt for machine configurations VoIP Features e SIP 2 0 RFC3261 compliant e Peer to Peer SIP proxy calls e Voice codec support G 711 G 723 1 G 729A G 729B e 1 38 FAX transmission over IP network e Voice processing Voice Active Detection DIMF detection generation G 168 echo cancellation 16mSec Comfort noise generation CNG e ln band out of band and SIP info DTMF support e Support Call Hold Call Forward Call Transter Call Waiting Call ID display and 3 way conference e Lifeline support for model VIP 157 Package Content The contents of your product should contain the following items VoIP Telephone Adapter Power adapter Quick Installation Guide User s Manual CD RJ 11 cable x 1 Physical Details The following figure illustrates the front rear panel of ATA Respective model descriptions are shown below VIP 156 SIP Analog Telephone Adapter VIP 156PE 802 3af PoE SIP Analog Telephone Adapter VIP 157
37. t with Peer to Peer mode The VIP 157_ Ahad set Auto Answer function for forwarding calls to arbitrary telephone If there have incoming IP calls and VIP 157_A doesn t answer the incoming calls after specific time the caller will hear prompt sounds to input the password then dial out an arbitrary PSTN telephone PB Swit n Intranet if 192 168 0 1 192 168 0 2 192 168 0 3 LAN LAN Phone Number LAN 3311 1424 VIP 157_A VIP 156 B VIP 156 C Enabled Auto Answer Function Set Phone Number 1111 2222 Machine configuration on the VIP 157 STEP 1 Please log in VIP 157_A via web browser browse to the Phone Settings menu and select the Call Forward config menu In the setting page please disable All Forward function and then the sample configuration screen is shown below Forward Setting You could set the forward number of your phone in this page All Forward GO OIP OPSTN Busy Forward Go OIP No Answer Forward or OIP OPSTN es oo o me O URL Number All Fwd No i No Answer Fwd No Busy Fwd Mo ao No Answer Fwd Time Out 3 2 8 Ring 50 STEP 2 Please log in VIP 157_A via web browser browse to the Phone Settings menu and select the Auto Answer config menu In the setting page please enable the Auto Answer and PIN Code Enabled function then the sample configuration screen is shown below Auto Answer You could enable disable the
38. tar key DHCP will be disabled and 112XXX XXX XXX Setup Static IP Address when entering a decimal system will change to the XXX point Static IP type Use the star key 113XXX XXX XXX Set Network Mask when entering a decimal Must set Static IP first XXX point Use the star key 114XXX XXX XXX Set Gateway IP Address when entering a decimal Must set Static IP first XXX point Use the star key 115XXX XXX XXX Set Primary DNS Server when entering a decimal Must set Static IP first XXX point For PLANET IPX 2000 IP PBX System 136 Enable auto config mode None For PLANET IPX 2000 IP PBX System 137 Disable auto config mode None Factory Reset None Must unlock the protect function before set up network settings via keypad The system will be lock and can t set up network settings via keypad The system will reboot automatically The system will be reset to factory default value and reboot automatically To switch PSTN mode None VIP 157 only 14 In initially firmware version V1 0 the VIP 157 default machine operation is at PSTN mode If user want to make a Hint VoIP phone call please press the key to switch to PSTN mode After latest firmware version V2 0 or higher the VIP 157 is at VoIP mode If user want to make a PSTN phone call please press the 0 key to switch to PSTN mode Following keypad commands c
39. y status Registered 37 STEP 3 Repeat the same configuration steps on ATAB and check the machine registration status make sure the registrations are completed Test the scenario 1 Pick up the telephone on ATA A 2 Press the keypad 1001 shall be able to connect to the AIAB 3 Then the telephone set in ATA B should ring Please repeat the same dialing steps on ATA B to establish the first voice communication from ATA A 38 Case 4 Voice communication via IP PBX system IPX 2000 Auto config In the following sample we ll introduce how to integrate the ATA with our IP PBX system IPX 2000 via Auto config feature Registration Registration Authentication Authentication IPX 2000 LAN IP Address 192 168 0 50 B ATABIP Address 192 168 0 2 B ATAAIP Address 192 168 0 1 Line Number 2002 Line Number 1001 Device configurations on the IPX 2000 STEP 1 Log in IPX 2000 and browse to the Srevice gt DHCP Service menu and create new options list for the auto configuration DHCP SERVICE Single host as 190 168 1101 190 168 1 200 150 192 168 1 1 E 151 http 192 168 0 50ARpboot S Ee CEN Code please insert 151 as the DHCP server option Value http LAN IP for IPX 2000 tftpboot An example option 151 would be option 151 value http 192 168 0 50 tftpboot 39 STEP 2 Please browse to the Device gt IP Phone menu and create new device And press th
Download Pdf Manuals
Related Search