MODEL CX812 HAND PUNCH
Contents
1. Bee will repair or replace the item at our discretion and subject to our inspection e Repaired or replaced items will be returned to you pre paid by our choice of carriers e Busy Bee reserves the right to refuse reimbursement or repairs or replacement if a third party without our prior authorization has carried out repairs to the item e Repairs made by Busy Bee are warranted for 30 days on parts and labour e Any unforeseen repair charges will be reported to you for acceptance prior to making the repairs e The Busy Bee Parts amp Service Departments are fully equipped to do repairs on all products purchased from us with the exception of some products that require the return to their authorized repair depots A Busy Bee representative will provide you with the necessary information to have this done e For faster service it is advisable to contact the nearest Busy Bee location for parts availability prior to bringing your product in for repairs OG2. KA CRAFTEX bd C SERIES MODEL CX812 HAND PUNCH USER MANUAL COPYRIGHT 2015 BY CRAFTEX INDUSTRIES INC hum CONSENT oF RATE NOUSTRES ne Version 1 0 CRAFTEX coe CX SERIES SPECIFICATIONS MODEL CX812 HAND PUNCH As part of the new line of Craftex CX Series Metalworking Tools we are proud to offer the CX812 Hand Punch By following the instructions and procedures laid out in this user manual you will receive years of excellent service and satisfaction The CX812 is a professional tool and like all tools proper care and safety procedures should be adhered to Thickness 0 5 1 5mm 1 5 2 5mm 2 5 3 5mm 3 5 5 0mm Aluminum 2 5 20mm 3 0 20mm 5 0 20mm 8 0 20mm is a Copper 3 0 30mm 5 0 20mm 6 0 20mm 8 0 20mm unch AB LLL A3 carbon Gosomm 8 0 18mm 10 17mm steel Country of Origin China MAICII rot oen elie iene 84 Kg NV ATLANT saca aa eva aiva a aia 3 Year gt CRAFTEX 2 Ba CTED UNPACKING The CX812 is properly packaged in a carton for safe transportation When unpacking carefully inspect the carton and ensure that nothing has been damaged during transit INVENTORY The hand punch consists of the following CONTENTS QTY A Hand Punch eee 1 B Handle eneen 1 C Handle Extension 1 D Hex BoltS a nana nean e eee 2 E Flat Washers nn 4 AN mms sans ne 2 While doing the inventory if you can not find any parts ch
3. SSURE PLATE LEFT 6 PRESSURE PLATE RIGHT 7 RAM 8 ROCKER BLOCK 9 TABLE 10 DIE 11 WORK STOP 12 HANDLE BRACKET 13 PIVOT PIN 14 PORTED PIVOT PIN 15 HANDLE PIVOT PIN 16 ZERK FITTING 17 GEAR COVER 18 SPRING PLATE 19 PUNCH 20 PUNCH PIN el FLANGE BOLT M5 8 X 10 22 HEX BOLT M10 1 5 X 20 23 SPRING BRACKET INNER 24 SPRING BRACKET OUTER 25 FLANGE BOLT M8 1 25 X 25 26 TORSION ROD 27 HEX BOLT M16 2 X 70 28 SPECIAL SET SCREW 29 HEX BOLT M6 1 X 8 30 FLANGE BOLT M10 1 5 X 20 31 FLAT WASHER 16MM 32 SPECIAL NUT M16 33 SPECIAL NUT M20 34 FLAT WASHER 20MM 35 FLAT WASHER 20MM 36 HEX BOLT M12 1 75 X 60 37 HANDLE 2PC SET V2 11 02 38 HEX BOLT M12 1 75 x 55 39 FLAT WASHER 12MM 40 HEX NUT M12 1 75 lt gt CRAFTE ay ete 4 lt 2 CRAFTEX WARRANTY CRAFTEX 3 YEARS LIMITED WARRANTY Craftex warrants every product to be free from defects in materials and agrees to correct such defects where applicable This warranty covers three years for parts and 90 days for labour unless specified otherwise to the original purchaser from the date of purchase but does not apply to malfunctions arising directly or indirectly from misuse abuse improper installation or assembly negligence accidents repairs or alterations or lack of maintenance V c Proof of purchase is necessary All warranty claims are subject to in
4. eck if the part is already installed on the hand punch ASSEMBLY Attach the handle to the hand punch and secure it by using the hex bolts and flat washers provided See figure 1 Figure 1 Attaching the handle The CX812 comes with a handle extension used for operations when additional leverage is required To install the extension handle simply slide the handle extension over the handle MOUNTING The hand punch features four pre drilled holes on its base which allow mounting it to the workbench There are two ways to mount the hand punch onto the workbench through mount and direct mount Through Mount is the strongest mounting option where the holes are drilled all the way through the workbench Hex bolts washers and hex nuts are used to secure the hand punch to the workbench See figure 2 Hex Bolt gt Fiat washer gt Lock Washer gt Hex Nut Figure 2 Through mount Direct Mount is to simply secure the hand punch to the workbench using lag screws See figure 3 1 EW Flat Washer Machine Base Figure 3 Direct mount Place the hand punch on the workbench and use the holes on the base as a quide for drilling and attaching the punch to the workbench BASIC CONTROLS Below are some of the basic controls on your CX812 hand punch ry Work Stop Adjustment Bolts a e i a Figure 4 Basic controls Punch Pin Secures the punch and w
5. hen removed allows for changing of the punch Die Adjustment Bolts Adjusts the position of the die to align with the punch SCRAFTEX 4 B CIT Work Stop Aligns the work piece for making repetitive punches Handle When lowered pushes the punch through the work piece and into the die PUNCHING Position the work piece between the punch and die aligning it with the center of the punch WARNING Always wear safety glasses and gloves when operating the hand punch Failure to do so could result in serious personal injury Pull the handle down towards you to force the punch into the work piece until the punch is completely through the work piece Return the handle to its uppermost position and remove the work piece REPETITIVE PUNCHES The CX812 comes with a work stop used to make repetitive punches easily To make repetitive punches Position the work piece between the die and the punch Lower the handle half way and check the proper position of the punch Now lower the handle all the way down to force the punch into the work piece until the punch is complete Loosen the cap screw securing the work stop and adjust the work stop to line up the work piece Re tighten the cap screw securing the work stop Return the handle to the uppermost position and remove the work piece Position the work piece against the work stop and make additional punches WARNING Do not force the machine t
6. o do the job for which it is not designed Failure to do so could result damage to the punch REPLACING PUNCH AND DIE You will want to replace the punch and die when you need to change the size of the punch or when the punch and die has become worn To change the punch and die Loosen the die adjustment bolts and remove the die a gt 3 gt NA Die Adjustment 4 Bolts Pee Figure 5 Die adjustment bolts amp punch pin Tap the punch pin using a mallet until it moves freely but do not fully remove it Hold the punch with a rag or gloves and remove the punch pin to release the punch Slide the new punch into the hole and align the flat side of the punch with the punch pin Insert the punch pin securing the punch into the machine Place the new die in position and lower the handle Adjust the die so that the punch fits into the die Once the die is in the correct position tighten the die adjustment bolts to secure it in position MAINTENANCE Maintaining your hand punch is quite simple and easy Always check the hand punch for any loose mounting bolts loose handle worn or damaged punch or die before operation Apply a light coat of grease to the gear teeth between the handle and the main body of the hand punch S mik umopye ig Sued PARTS LIST PART DESCRIPTION 1 BODY 2 HANDLE BASE 3 JOINTING PLATE LEFT 4 JOINTING PLATE RIGHT 5 PRE
7. spection of such products or part thereof and Craftex reserves the right to inspect any returned item before a refund or replacement may be issued This warranty shall not apply to consumable products such as blades bits belts cutters chisels punches etceteras Craftex shall in no event be liable for injuries accidental or otherwise death to persons or damage to property or for incidental contingent special or consequential damages arising from the use of our products RETURNS REPAIRS AND REPLACEMENTS To return repair or replace a Craftex product you must visit the appropriate Busy Bee Tools showroom or call 1 800 461 BUSY Craftex is a brand of equipment that is exclusive to Busy Bee Tools For replacement parts directly from Busy Bee Tools for this machine please call 1 800 461 BUSY 2879 and have your credit card and part number handy e All returned merchandise will be subject to a minimum charge of 15 for re stocking and handling with the following qualifications Returns must be pre authorized by us in writing We do not accept collect shipments Items returned for warranty purposes must be insured and shipped pre paid to the nearest warehouse Returns must be accompanied with a copy of your original invoice as proof of purchase Returns must be in an un used condition and shipped in their original packaging a letter explaining your reason for the return Incurred shipping and handling charges are not refundable e Busy
Download Pdf Manuals
Related Search