Digi-View User Manual 9 Aug 10
Contents
1. Important Safety Precautions Damage caused by non compliance with this operating manual will void the warranty We will not assume any liability for damages to items or persons caused by improper handing or non compliance with the safety notices Any warranty claim will be null and void in such cases 1 Do not drop puncture or disassemble the camera or monitor otherwise the warranty will be void 2 Never tug on the power cords 3 Do not expose the monitor to high temperature or leave it positioned in direct sunlight e g permanently fixed to the windscreen Doing so may cause damage or temporary malfunction 4 Use the system with care only gentle pressure is required to operate the monitor buttons 5 For your own safety avoid using the camera or power off when there is a storm or lightning 6 Remove the monitor power adapter during long periods between use 7 Use only the accessories and power adapters supplied by the manufacturer 8 To meet the regulations pertaining to parental responsibility keep the devices out of the reach of infants 9 Ensure that power cables do not get crushed or damaged by sharp edges This device complies with Part 15 of the FCC Directive 2004 108 EC Low Voltage Directive FCC Compliance Statement Products with CE Marking comply with EMC Rules Operation is subjected to the following 73 23 EEC R amp TTE 1999 5 EC issued by the two conditions Commission of the European Community 12. 7 Menu Mode Cursor Right Vol QUAD View Mode Hot key CH4 8 Menu Mode Menu Enter Button 9 View Mode Scan Channels Menu Mode Pair Camera In View mode manually scan the available camera channels In Pair mode assign and pair a camera to a specific channel 10 View Mode Resolution Switch Switch between VGA and QVGA resolution A It is recommended to set the resolution to QVGA See Basic Operation In the View Mode section as a guide 11 Reset Switch Press with a pin small object to reset and restore system hardware status Press the switch ONLY if the system has crashed and there is no response from any of the buttons In View Mode 1 Signal Indicator 2 Channel Indicator 3 Resolution Indicator 1 Status Indicator A Signal Indicator shows signal strength more bars indicate a stronger signal Signal Level VGA Frame Rate QVGA Frame Rate E A C A It is recommended to set the resolution to QVGA To do so simply press the Resolution button to switch to QVGA as shown on the Resolution Indicator B Reversing Camera Operation Steps 1 Press Power button to switch ON 2 Switch to QVGA mode if necessary 3 Select reverse gear if the camera is powered by the reversing light 4 Reverse image will be displayed 5 If the a camera is used to view the interior of a vehicle horsebox trailer or behind a caravan motor home then it should be powered fr
3. Trailer Vision User Manual Model Digi View Digital Wireless Camera System This is a driving aid safe driving good observation and use of the rear view wing mirror are still necessary 9 ai vn PLEASE READ CAREFULLY AND SAVE This manual contains important information about this product s operation If you are installing this product for others you must leave this manual or a copy with the end user 1 Digi View Index system Components Safety Precaution and Hazard Notice FCC Warning Disposal system Parts Getting Started Step1 System Connection Step2 Basic Operation Monitor Function Buttons and Display Indications View Mode Step3 Advanced Operation The Menu setting Auto Manual Scan Sequence setting QUAD Display Pairing a Camera system Setup and Reset Trouble Shooting Trouble Shooting Table Product Specification System Components 1 Digital Wireless IP65 Colour Camera 1 Digital Wireless 3 5 LCD Monitor 1 Antenna for the camera 1 5V Cigarette Lighter Power Adapter for the Monitor 1 Dash board mount for the Monitor 1 Windscreen mount for the Monitor 1 Screw fixings bag 1 User Manual WELCOME Dear Customer Thank you for purchasing this unique product which utilises the latest digital wireless technology ensuring ZERO interference Please read the following information carefully before installing and using this product
4. this device may not cause harmful Compliance with these directives implies conformity interference and to the following European Norms 2 this device must accept any interference EMC EN 301 489 received including interference that may LVD EN 60950 Cause undesired operation Radio EN 300 328 FCC CE WARNING This equipment has been tested and found to comply with limits for a Class B digital device pursuant to Part 15 of the FCC rules and ETSI EN 300328 These limits are designed to provide reasonable protection against harmful interference in residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television equipment reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Move the equipment away from the receiver Plug the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio television technician for additional suggestions You are cautioned that any change or modifications to the equipm
5. Input Socket 2 Pair LED Indicator 7 LCD Screen 12 Cigarette Adaptor 3 Power LED Indicator 8 Monitor Stand 13 Windscreen Mount 4 Control Panel 9 Reset Button 14 Dash board Mount 5 Camera Select Pair 10 Power Button Getting Started Step1 System Connections Camera Installation 1 For reversing choose a location on the rear bumper etc that you wish to install the camera usually in the middle of bumper fora HGV motor home caravan etc high up and looking down backwards usually gives the best view For inside a horsebox trailer mount the camera high up and ideally behind the horse s 2 Screw the camera s mounting bracket to the desired location 3 For reversing connect the power cable to the reversing light of the vehicle and the camera will be automatically powered when the vehicle is in reverse otherwise connect to any available power source e g the side lights ideally use a switched source to prevent inadvertent battery drain Camera Antenna Installation X Camera Camera 4 o r AB 168 Screw the dipole antenna to the antenna connector LCD Monitor Installation 1 Remove the protection film from the LCD monitor 2 Secure the windscreen holder to the back of the monitor with the 4 screws provided 3 Attach the rubber pad to the windshield Make sure the glass is c
6. a and monitor that might reflect absorb the signal Obstacles could include furniture cabinets or walls If the wireless signal strength is low position the monitor antenna at a new angle ideally vertically or readjust camera monitor position until an improvement is achieved Or if possible relocate the camera closer to the monitor Why Image Compression In order to achieve a secure and interference free signal this digital wireless system utilises a narrow 2Mb frequency hopping bandwidth Different from traditional 2 4GHz analogue wireless systems the digital wireless signal is compressed and then transmitted in Motion JPEG MJPEG format By digitising and compressing the raw analogue data the available bandwidth is used more efficiently securely Consequentially you might observe an indent image line if you are using a larger display monitor or a plasma TV How to improve the image quality when using large display screens When QVGA is selected pixel scattering is unavoidable However you can change the image to VGA and by doing so more pixels are scattered on the screen Therefore to achieve the best display performance when outputting the video signal a 32 or smaller monitor TV is recommended 14 Trouble Shooting Table Before requesting service please refer to the checks detailed below If you are in any doubt about the following or if the solutions described in the table do not solve the problem please
7. contact us Problem Possible Remedy Cause System No power Check that the reversing light if the camera is powered Message supply to the from the reversing light is working Check the camera shows NO corresponding wiring ensure the polarities are correctly connected and 12 Signal camera s 24V is available on monitor screen To complete Pairing ensure that the camera is powered select camera to Pair via the monitor menu then press the camera pairing button See Advanced Operation Pairing Camera section as a guide Channel is not paired with the camera Low signal or unstable signal Camera image is missing during manual scan Dim over bright image on monitor screen Image frozen and the monitor Antenna directional limitation Adjust amp secure camera antenna position camera amp monitor antenna vertically Strong radio Relocate source of the radio signal or reposition the signal nearby camera monitor Scan Press OK button go to the menu and enable the channel s channel s See Advance Operation Setting Auto al set Manual Scan Sequence for detail Monitor brightness adjusted incorrectly Press OK button go to menu enter System Setup adjust Brightness See Advance Operation System Setup for detail System crash Use a pin small object to press Reset Switch to restore the system function buttons don t respond For technical support pleas
8. e email support trailervision co uk PRODUCT SPECIFICATION Maximum Channels 1 4 Communication Range 200 metres in open space ow S o Current Consumption Night View Range Dimension O Trailer Vision 15
9. ent not expressly approved by the party responsible for compliance could void your authority to operate such equipment Disposal If the camera system no longer functions or can no longer be repaired it must be disposed of according to the valid statutory regulation for disposal of spent batteries such equipment a we u TS You are required by law Battery Ordinance to return all spent batteries and accumulators Disposing of spent batteries accumulators with common household waste is prohibited Batteries accumulators that contain hazardous substances are marked with the symbols on the side These symbols indicate that it is prohibited to dispose of these batteries accumulators in household waste The abbreviations for the respective heavy metals are Cd cadmium Hg mercury Pb lead You can return spent batteries and accumulators that can no longer be charged to the designated collection points in your community outlets or wherever batteries or accumulators are sold Following these instructions will allow you to fulfill the legal requirements and contribute to the protection of our environment The System Parts Wireless Camera 1 Camera Lens 2 Pairing key under cover 3 Mounting Bracket 4 IR LED Night Vision 3 5 LCD Wireless Receiver Ill ti Gates 5 EDS light sensor 6 Antenna 7 Power Cable 8 Pair LED Indicator 9 Power LED Indicator 1 Antenna 6 Resolution Switch 11 DC
10. is available for multi camera use Before setting QUAD display make sure all cameras are paired to assigned channels See Advance Operation Pair Camera section as a guide A QUAD display will be restored to one camera display every time you press the directional keys for manual scan A Toensure correct display turn all available channels ON prior to selecting QUAD mode Resolution QUAD CAM1 CAM2 CAM3 CAM4 Pair CAM System Factory Resolution QUAD CAM1 CAM2 CAM3 CAM4 Pair CAM Systern Factory A Use Left Right to turn all available channels ON B Use Left Right to change Scan Time to QUAD C QUAD display as shown Unavailable channel will be displayed as a blank screen A Toleave QUAD display simply press Left Right Up Down to go to specific channel Left CAM4 Right CAM3 Up CAM 1 Down CAM2 A In QUAD display ZOOM Pair functions are not available 11 Pairing Camera s A Proceed with this function ONLY when a camera can not be found by the system or when you have additional new camera s to pair A Before pairing the camera make sure that the camera power cable is correctly connected to the reversing light power source A Simply pair the camera by selecting the desired channel in Menu Mode B Only assign one camera to one channel Channel memory will be overwritten if used again C Pairing new camera to channel 3 settings as shown Pai
11. lean and dry to ensure that the holder fixes securely 4 Pull the lock knob down to fix the holder this mount is not designed to be left permanently in the windscreen please use the dashboard mount for permanent fixture 4 Connect the cigarette lighter power adaptor to the DC power jack of the LCD monitor ONLY use the provided power adaptor a hard wire power adapter is available separately 5 Plug the cigarette lighter power adapter into the vehicles cigarette lighter socket which may operate via the ignition 6 Position the monitor antenna amp camera antenna vertically to achieve the best reception 53 B 5 DC WaS Pa Cigarette Power Source gi 7 Step 2 Basic Operation Monitor Function Buttons and Indicators a O OO Qr 2 1 Power Button Press button to power ON hold it for 2 seconds to power OFF the monitor 2 Pair indicator Illuminated when the system is operating properly blinking when the system is pairing with a new camera 3 Power Indicator LED comes ON when the Monitor is powered ON A LED remains ON while monitor is OFF in Power Save Mode 4 Menu Mode Cursor UP QUAD Mode Hot key CH1 5 Menu Mode Cursor DOWN QUAD View Mode Hot key CH2 6 Menu Mode Cursor Right Vol QUAD View Mode Hot key CH3
12. n setup Problem Diagnosis This innovative digital wireless solution integrates advance Frequency Hopping Spread Spectrum FHSS technology This technology greatly reduces the interference that comes from other devices using the same radio frequency 2 4GHz e g WIFI Bluetooth cordless phones etc You can now enjoy superior wireless picture quality without a flickering or noisy image However weaker signal lag or still image may be observed from time to time depending on the environment where the system is installed The system complies with FCC part 15 247 ETSI EN 300 328 audio video signals transmitted about or over 500 feet 150 metre in the line of sight However line of sight installation is difficult to achieve due to obstacles etc Factors affecting transmission include microwave ovens and or other high frequency electromagnetic waves Reinforced concrete walls large scale metal products and objects should not be located near to the camera or the monitor Water also creates an obstacle to signal transmission as it absorbs the signal and should be avoided People etc passing through the transmission area may also cause unstable signal quality However in normal use as a rear view or interior vehicle camera the system should offer excellent performance and provide a clear and interference free image view How to improve the wireless signal quality If possible remove any obstacles from between the camer
13. om an ignition controlled circuit or a lighting circuit could also be used A STOP REVERSING when NO Signal shows on the monitor A Press Cam button to locate the reversing camera channel if necessary A This is a driving aid safe driving good observation and use of the rearview wing mirror are still necessary Note The Channel indicator shows the current camera viewed by the monitor by pressing the Cam button you can manually switch between different cameras see below 0 Till 00 Camera Camera 2 Camera 3 Camera 4 Step3 Advanced Operation Knowing the Menu By Pressing OK Menu you can enter exit Menu Mode You can Use Left Right Up Down to select and change the settings Resolution QVGA QUAD OFF CAM1 ON CAM2 OFF CAM3 OFF CAM4 OFF Pair CAM 1234 System Setup Factory Reset Setting The Resolution You can use Left Right to change Resolution between VGA and QVGA Resolution Ova QUAD OFF CAM1 ON CAM2 OFF CAM3 OFF CAM4 OFF Pair CAM 1234 System Setup Factory Reset Setting Auto Manual Scan Sequence A This function is available for multi camera use A QUAD will be turned off every time you press be Cam for manual scan Resolution QVGA QUAD OFF a eM A Use Left Right to change QUAD to OFF CAM3 OFF CAM4 OFF Pair CAM 1234 B Press Ce to manual scan Systern Setup Factory Reset 10 Setting QUAD Display A This function
14. r CAM 1 264 D Press Pair button NOT OK E System will begin count down within 60 seconds system message as shown Please Press Pair Key on 60 F Within the 60 second count down press the Pair Key located on the camera cable A To compete Pairing select reverse gear if the camera is powered by the reversing light otherwise ensure that the camera is powered have the hand brake ON then press the camera Pair button with ignition on but engine NOT running G Once pairing completed camera and receiver status indicators as shown CO0DO0Y 12 System Setup Resolution VGA QUAD OFF CAM System Factory Reset Brightness a eS Frequency 50Hz Brightness me a Frequency Resolution VGA QUAD OFF CAM1 ON CAM2 OFF CAM3 OFF CAM4 OFF Pair CAM 1234 System Setup Factory gt Select System Setup press OK to enter B Use Left Right to adjust monitor brightness A Brightness setting effects the LCD monitor only C Use Left Right to change frequency between 50Hz and 60Hz for the UK please set the frequency to 50HZz A Select Factory Reset press System will restore the original factory default settings 13 Trouble Shooting This section offers some helpful information to overcome most of the problems that you may encounter We also hope that this section assists you to achieve a quick and easy installatio
Download Pdf Manuals
Related Search