CL25AE - Energy efficient Honeywell portable evaporative air
Contents
1. 2 hae www jmatek com Model CL25AE E mail usinfo jmatek com 1 Control Panel 5 Casters 9 Remote Control 2 Handle 6 Ice Compartment Lid 10 Water Fill Door 3 Horizontal Louvers 7 Vertical Louvers 11 Drain Plug 4 Power Cord amp Plug 8 Water Level Indicator 12 Water Tank WARNING READ AND SAVE THE AIR COOLER SAFETY amp MAINTENANCE GUIDE AND USER MANUAL BEFORE USING THIS PRODUCT FAILURE TO FOLLOW THESE INSTRUCTIONS MAY DAMAGE AND OR IMPAIR ITS OPERATION AND VOID THE WARRANTY CONTROL PANEL Tank Empty FUNCTION BUTTONS POWER Press the POWER button to turn the unit on The cooler will start automatically at medium speed After a few seconds the speed will switch to low To turn the unit off press the button again SPEED Press the SPEED button repeatedly to change the speed between Lo Med Hi Sleep The indicator light will show the selected speed Low Lo lt gt Medium Med lt gt High Hi gt gt Sleep Sleep When the SLEEP mode is selected the fan will run on High for one hour then Medium for the second hour and on Low speed from the third hour onwards until you switch off the unit Applicable for models with Sleep feature only EN 1 FUNCTION BUTTONS CONTINUED TIMER Press the TIMER button until the desired time duration setting is selected When the set time has passed the unit will automatically2. DUST FILTER AND HONEYCOMB COOLING MEDIA Figure 1 e The appliance is supplied with a Carbon Dust Filter amp Honeycomb Cooling Media Rear Frame e The Carbon Dust Filter and Honeycomb Cooling Media are located inside the Rear Grill See Figure 1 for instructions on how to remove them from the unit for cleaning and maintenance Do not run the unit in COOL mode with stale water in the tank You must empty the water tank and refill with fresh water especially if the tank has not been cleaned in a long Push I Carbon Dust Filter Screws time Removing the Carbon Dust Filter Honeycomb Cooling Media e The cleaning frequency for the Honeycomb media depends 1 Remove all the screws from the Rear Grill szi 2 Carefully push the left and right side of the rear grill and on local air and water conditions In areas where the mineral pull out from the cooler content of water is high mineral deposits may build up on the 3 Pull out the Carbon Dust Filter and clean with water as needed Honeycomb Cooling Media and restrict air flow Draining the To release the Honeycomb Media pull out the Rear water tank and refilling with fresh water at least once a week Frame ane ide outor the trame Replace or clean media with water and a damp cloth as will help reduce mineral deposits If mineral deposits remain needed on the Honeycomb Cooli
3. Service Center for more information Check water tank amp other cooler parts If you see mold spots or suspect an algae issue use a damp cloth to wipe away the algae until all spots have disappeared Make sure all parts are clean amp dry before storage Contact the Customer Service Center if problem persists Replace with new batteries Follow the polarity guide inside the battery compartment If replacing new batteries in the correct position does not work contact the Customer Service Center Try to activate the unit with the Remote Control If the unit responds then the Control Panel on the unit may be experiencing problems contact the Customer Service Center If neither the Remote Control or the Control Panel is working contact the Customer Service Center A small amount of rain on the unit is not a problem as long as the electrical plug and outlet are dry If they are wet DO NOT touch the unit or electrical plug outlet Switch off the master power for the outlet before unplugging the unit from the electrical outlet Make sure all outlets and plugs are dry before use The Air Cooler is designed to IPX4 product standards and not recommended to be placed outdoors during heavy rain conditions Do not operate the Air Cooler when wet Wait for the Air Cooler to dry before plugging in and turning on the unit again Honeywell Portable Evaporative Air Cooler User Manual Read and save these instructions before use
4. continuously The unit will automatically pause evaporative cooling Refill the water tank to deactivate the alarm in cooling mode First switch OFF the unit and unplug from the power outlet Fill the water tank with water above the minimum water level mark Plug in and switch ON again To deactivate the alarm and continue using the unit as a fan without evaporative cooling switch the unit OFF and then ON again The Low Water Alarm will not activate in Fan only mode The Low Water Alarm will sound again if the COOL function is activated while the water tank is still empty CLEANING amp DRAINING THE WATER TANK Below are instructions on how to clean and maintain your air cooler If the cooler will not be used for a long period of time please refer to the STORAGE amp MAINTENANCE GUIDELINES located in the separate Safety amp Maintenance Guide WARNING Before cleaning the unit switch the unit OFF and disconnect from the electrical socket e Move the unit to a location where the water can be drained Remove the cap from the Drain plug located at the bottom of the unit Allow the tank to empty e Refill the water tank with clean water up to the maximum level and drain it completely Use damp cloth to remove the dirt and dust from the surface of the unit Never use corrosive elements or chemicals to clean this product e When the product is not in use store the unit in a dry place our of direct sunlight CLEANING THE CARBON
5. Honeywell Portable Evaporative Air Cooler Safety amp Maintenance Guide User tips and safety instructions www jmatek com E mail usinfo jmatek com THANK YOU Congratulations on your purchase of this versatile Honeywell Evaporative Air Cooler The Safety amp Maintenance Guide and the separate User Manual are intended to provide you with important information needed to set up operate maintain and troubleshoot this product USER TIPS What is Evaporative Cooling Honeywell Evaporative Air Coolers are built to maximize energy efficiency and keep energy costs low Warm air is drawn into the cooler and enters the Honeycomb Cooling Media Water pumped from the water tank pours over the Honeycomb Cooling Media As the warm air passes through the Honeycomb Cooling Media the water absorbs the heat naturally cooling and humidifying the air A fan propels the cooled air out into the room This no compressor system cools naturally efficiently and inexpensively Honeycomb Cooling Media Evaporative Air Cooling Mechanism The recommended maximum relative humidity level is 60 or less which allows a noticeable temperature decrease The temperature will be lower in drier climates because higher evaporation occurs when the humidity is low NOTE When the product is used for the first time the Honeycomb Cooling Media will have an odor which will dissipate in a few hours or so of initial use To ma
6. connected to a continuous water supply you must switch off the water supply and remove the drain tube before draining the water tank This function is only available on some Honeywell Air Cooler models Check the User Manual to see if your unit has the Continuous Water Supply Function Clean the water tank with a damp cloth to wipe away any dust or mineral deposits Remove the Honeycomb Cooling Media and Carbon Dust Filter from the Air Cooler and rinse under fresh water to remove dust and dirt Replace the Honeycomb Cooling Media and Carbon Dust Filter after they are clean and dry To protect the unit from dust and scratches cover with a clean cloth or plastic bag before storing Coil the power cord and store it away from the floor to protect it Carbon Dust Filter is available in specific models of Honeywell Air Coolers only Check the User Manual for your model to see if it includes a Carbon Dust Filter Customer Service Center See the last page of the User Manual to find the contact details for the Customer Service Center for your area PROBLEM No discharge of air Not Cooling Unit is making noise Excessive humidity in the room Odors Remote control does not work The unit does not respond The outdoor Air Cooler is wet from rain POSSIBLE CAUSE Cord is not plugged in Power is not ON Pump is not turned ON Low or no water in tank when COOL is selected Damaged Pump or Calcium deposits on bl
7. e Always unplug the Air Cooler before refilling the water tank cleaning servicing or relocating the unit e Never pull the cord Remove it from the electrical outlet socket by grasping and pulling on the plug end of the cord e This appliance has been manufactured for use in domestic environments and must not be used for other purposes e DO NOT use in areas where gasoline paint or other flammable goods and objects are stored e When using the COOL setting make sure the water tank is at Max Indicator Level Operating the unit on the COOL setting with an empty tank may result in damage to the water pump e DO NOT attempt to repair or adjust any electrical or mechanical functions of the Air Cooler as this may void the warranty e DO NOT cover the cooler s air inlet or outlet as this may damage the motor e DO NOT insert or allow objects to enter any ventilation or exhaust opening as this may damage the unit and may cause electrical shock or fire e DO NOT operate with the Honeycomb Cooling Media removed as this will overload and damage the motor EN 2 DO NOT leave the operating appliance unattended for an extended period of time DO NOT allow children to play with this appliance packaging or plastic bags DO NOT continue to operate the unit if it is damaged or if it malfunctions Refer to the TROUBLESHOOTING section and contact the CUSTOMER SUPPORT CENTER Always place the unit on a dry level floor DO NOT use in bathrooms o
8. nd animals COOLER LOCATION Make sure to position the air cooler correctly before you set up and start using the product Please refer to the COOLER LOCATION section of the separate Safety amp Maintenance Guide FILLING WITH WATER CAUTION Unplug the unit from the electrical power outlet before emptying or refilling the water tank Open the Water Fill Door located on the side of the unit The Water Level Indicator is located at the front of the unit Refill the water tank when water level is low Do not fill water above the Max water level mark to Water Fill Door avoid water droplets collecting on the louvers Check the water level in the tank before running the COOL function Make sure that the water in the tank is above the minimum water level mark Running the unit in COOL mode with inadequate water may cause pump failure Note The water capacity refers to the total volume of water that can be contained within the air cooler water tank and water distribution system The water capacity in the tank at the Max indicator level may be lower than the actual water capacity of the air cooler Ice Compartment Note If ice is available you may add ice in the top ice compartment to enhance the cooling performance LOW WATER ALARM The unit is equipped with a low water sensor In Cooling Mode when water in the tank is below the minimum level you will hear a beeping sound and the TANK EMPTY indicator light will flash
9. ng Media the media should be WARNING DO NOT operate the Air Cooler when the removed and washed under fresh water The media should Rear Grill or Rear Frame is removed from the Air Cooler be cleaned every two months or sooner depending on your or if there is a loose fitting Rear Grill or Rear Frame Doing so can cause serious injury or dangerous needs electrical shock e For best results allow the Honeycomb Cooling Media to dry after each use by turning off the cool function 15 minutes before turning the unit off Applicable for models with Carbon Dust Filter only JMATEK North America LLC Mahwah New Jersey 07495 USA Phone 1 800 474 2147 Email usinfo jmatek com Web www jmatek com Made in China 2015 JMATEK Limited All rights reserved The Honeywell Trademark is used under license from Honeywell International Inc Honeywell International Inc makes no representations or warranties with respect to this product This product is manufactured by JMATEK Limited Honeywell
10. nt outdoor electrical outlet e Set the unit on a solid flat surface IMPORTANT Honeywell Outdoor Air Cooler models are designed to IPX4 product standards and not recommended to be placed outdoors during heavy rain or snow WARNING READ AND SAVE THE AIR COOLER GUIDE AND USER MANUAL The Air Cooler Guide and User Manual are intended to provide important information needed to set up operate maintain and troubleshoot your Air Cooler Failure to follow these instructions may damage and or impair its operation create hazards and void the warranty READ AND SAVE THESE INSTRUCTIONS When using electrical appliances basic safety precautions should always be followed e Check the household voltage to ensure it matches the appliance s rating specifications e Before operating the product remove the packaging and check that product is in good condition e DO NOT operate with a damaged cord or plug If the supply cord is damaged it must be replaced with a supply cord which is as per manufacturers specifications by the authorized service centre or its service agent or a similarly qualified person in order to avoid a hazard e DO NOT use an extension cord with this unit e DO NOT run power cord under carpeting or cover it with rugs or runners Keep the cord away from areas where it may be tripped over e Always ensure the water tank is filled with water above the min level mark when operating the air cooler in evaporative COOLING mode
11. ower In cooling mode the Air Cooler produces moisture as a result of evaporative cooling This is normal When the Cooler is new Algae or mold due to moist parts In very damp conditions algae may form Remote control batteries are old amp used or inserted incorrectly in the battery compartment Damaged remote control Damaged Control Panel on unit The Air Cooler was placed outdoors this is only allowed for outdoor Air Cooler models and soaked by heavy rain SOLUTION Make sure power cord is plugged in and the switch is ON Turn the unit ON by pressing the power button on the control panel or remote control Turn on COOL function from remote or control panel Refill water tank Contact Customer Service Center The Air Cooler cools best in dry climates If the ambient humidity level is high 60 or above refrain from using the Air Cooler until ambient humidity is reduced Make sure the window doors are open and there is adequate cross ventilation in the room so that the moisturized air can circulate better Do not use the evaporative cooling function on days with high ambient humidity When the unit is used for the first time the Honeycomb Cooling Media will have an odor which will dissipate within a few hours of initial use Check the Honeycomb Cooling Media If you see mold spots on the media or suspect an algae issue remove and replace the Honeycomb Cooling Media Contact the Customer
12. r near water DO NOT keep the product where it may fall into a water container Store in a dry area when not in use This appliance is not intended for use by persons including children or elderly with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instructions concerning the use of the appliance by a person responsible for their safety Always grip the side handles to move the Air Cooler WARNING To reduce the risk of fire or electric shock do not use this appliance with any solid state speed control device Read the detailed CLEANING amp DRAINING THE WATER TANK instructions for your Air Cooler located in the separate User Manual Below is a general guideline for maintenance and storage of your Air Cooler WARNING Always switch OFF the Air Cooler and unplug it from the electrical source before cleaning or maintenance Cleaning At least once a week drain the water tank completely and refill with fresh water Doing this will greatly reduce mineral deposits and help to extend the life of the Honeycomb Cooling Media End of Season Storage If the Air Cooler will be used for a long time Make sure all parts are dry by running the Fan Only mode for about 30 minutes before storing time depends on ambient humidity conditions Switch OFF the Air Cooler and unplug from the power supply Empty drain all the water from the tank Note If the unit is
13. ter pump distributes the maximum amount of water to the Honeycomb Cooling Media This results in maximum water evaporation and the cooling performance improves REMOTE CONTROL POWER ON OFF SPEED Low Medium High Sleep MODE Controls cooling or fan option SWING Controls the motion of the louvers TIMER Controls the Timer function for automatic off Applicable for models with Sleep feature only Note e The remote control requires AAA 2 x 1 5V batteries for replacement Open the battery compartment at the back of the remote control and insert the batteries inside Care must be taken to insert the batteries according to the correct polarity markings shown inside the battery compartment e Always point the remote control signal transmitter towards the unit when operating Make sure that the signal path is not obstructed e Remove the batteries if the unit is not going to be used for an extended period of time e Do not drop the remote control EN 2 REMOTE CONTROL CONTINUED Do not mix different types of batteries such as alkaline carbon zinc or rechargeable batteries Do not mix old and new batteries Do not recharge the battery e Exhausted batteries are to be removed from the product and safely disposed of as per local regulations e Do not dispose of batteries in fire Batteries may explode or leak WARNING Caution for ingestion of the small battery Keep away from children a
14. turn off unit remains in Standby mode until power cord is unplugged from electrical socket The TIMER function allows you to program the unit for up to 7 5 hours of use SWING Press the SWING button until the SWING indicator light is illuminated on the control panel The louvers will begin to move left to right automatically Vertical Air Flow You can manually adjust the louvers to change vertical air flow LOUVER MOVEMENT MODE Press the MODE button to select COOL and FAN modes Pressing the MODE button until COOL is illuminated on the control panel activates evaporative cooling The water pump will operate and you will feel the cooler air after the Honeycomb Cooling Media is completely wet Pressing the MODE button until Fan is illuminated switches the unit to a fan only mode without evaporative cooling ROOM COOLING AND HUMIDIFYING In cooling mode Honeywell Air Coolers provide moisturized air through the Water Regulator evaporation of water There is a manual Water Regulator knob located in the ice compartment of the unit This allows you to adjust the amount of water pumped over the Honeycomb Cooling Media thus helping to control eae MIN cooling and humidification levels When the Water Regulator is set to MIN the water pump distributes a minimal amount of water to the Honeycomb Cooling Media This results in less water evaporation and reduces the cooling effect When the Water Regulator is set to MAX the wa
15. ximize efficiency position the Air Cooler according to the following guidelines Indoors Place the cooler in front of an open door or window Ensure that there is adequate cross ventilation in the room by leaving a door or window open opposite the cooler The Evaporative Air Cooler should not be used in enclosed spaces It must be kept level and there must be water in the water tank Doors and windows should be opened to allow free air flow The Evaporative Air Cooler works best when placed near an open window so that outside air is drawn into the Evaporative Air Cooler circulates in the room then exits via the door The maximum cooling effect is felt when a person is near the flow of air coming out of the Evaporative Air Cooler The Evaporative Air Cooler produces moisture and can be used to humidify dry air To be used for humidification the windows and doors should be closed EN IMPORTANT The evaporative air cooler is not an air conditioner as it does not use a compressor or refrigerant gas It should not be expected to cool as efficiently as a refrigerated air conditioner Outdoors for outdoor models only e Use only on GFCI Protected outlets sockets for USA only e Power cords must be secured to avoid tripping e The wiring and connections must be protected from water The electrical plug and Air Cooler connections must be dry at all times When used outdoors insert the air cooler electrical plug into an IP44 complia
Download Pdf Manuals
Related Search