Home

CYCLOPS FPV ASSISTANT V1.0 User`s Manual (Beta Version

1. 290 Dotted line indicates the H is flashing 3 Position indication in RTH H in the screen refers to the take off position A G refer to destinations when the take off point is in front of the plane then it displays H when the take off point is at the back of the plane H will flash If H is in the middle and does not flash it means that the plane is travelling back to the take off point If H is in the middle and flashes it means that the plane is deviating from the take off point at 180 degree Methods for RTH H is displayed at the left side turn left to travel back If H is displayed at the right side turn right to travel back Description of menu parameters setting Press UP and DOWN to enter main menu setting MENU SYSTEM CONFIG WAYPOINT EXIT SYSTEM CONFIGU SETTING DESCRIPTION Page 1 ATT DATA If the attitude angle parameters If the environment is not suitable for flying the displayed in the flying interface attitude angle parameters in flying interface will flash BAT SCALE Battery scale setting If the power consumption reaches the value set during the flying the battery scale symbol will flash RESET Clear current sensor Clear the first application or after current sensor RESET Clear air speed Re clear the air speed if the environment SERVO Confirm the servo center You need to confirm the servo center after you CENTER change the model aeroplane Please manually fly the pl
2. finished CYCLOPS UPDATING When update progression is 100 the screen will display as follows for system checking CYCLOPS UPDATING 100Z CHECKING After the checking the screen will display as follows CYCLOPS UPDATING 100Z gt UCCEEDED At this point you finishes update After update the system will automatically run the new program If the update fails the screen will display as follows CYCLOPS UPDATING 100Z FAILED The following cases may result in update failure 1 Update program is not available in TF card 2 Update program is corrupted 3 Update program does not match product ID
3. will display to LOCK symbols as follows If the operator controls aileron direction steer or elevator steer the course or the altitude lock will be released At this time the system will automatically control the plane attitude according to the control amount of the operators For example 1f the aileron is in 100 amount the plane will fly left right at 45 degree slope if the elevator steer is in 100 amount the plane will lift lower at 20 degree angle Until the control lever returns to the neutral the system will lock and keep the course and altitude at the moment Additional functions When TF card is inserted into the system and the system detects satellite signal press for seconds UP button and SD symbols will appear on the upper right corner and flash At this point the card starts storing the system data Press Reset and the card will restart storing the system data If you want to end data storage press UP button for 3 seconds and SD card symbol stops flashing and you end data storage Description of software updating CYCLOPS FPV ASSISTANT may be updated with TF mini SD card We will issue the update programs on Internet The clients may download the update program and copy it to the TF card 1 Download Update cyc 2 Copy Update cyc to TF card and insert TF card into CYCLOPS FPV ASSISTANT main board 3 Press OK and start up the system release the button when you see the following picture until the update is
4. CYCLOPS FPV ASSISTANT V1 0 User s Manual Beta Version The product is an auxiliary piloting equipment with OSD auto pilot functions for FPV lovers The product has the advantages of small size light weight well developed functions and simplified operations Hardware configurations T 7 ig ar zo CRE ERR L RAON ENE IN A ee 3 k FRC a ST eee Servo cable gt eee in ce gt eee ae t a i i aniani p os aes ore FN IR sensor Vertical IR iyo ca Description of the pins Jumper number Current sensor interface TF card socket See Table 1 Horizontal IR sensor interface Vertical IR sensor interface CYCLOPS Switch board maa FP Y ASSISTANT Airspeed GPS module interface To battery T connector should be purchased separately Table 1 PCB Functions Equipment connected Signal mode Remarks indications i Main board 12V power or 3S lipo DC Working voltage 6 14V oe battery Jumper If only the power is 12V or 3S Lipo battery the main board can use the power battery 1 and 2 short circuit to power main board by another battery 2 and 3 short circuit to power the main board by power battery Video output Video frequency NTSC PAL Automatic detection of video signal power supply consistent with the main board voltage NTSC PAL Automatic detection of video signal power supply consistent with the main board voltage eL ll output la a aa output ee e o
5. LOPS CYCLOPS FPU ASSISTANT HO SD CARO FOUND About 5 seconds later the system will enter pilot display Distance between Position of the plane GPS signal plane and controller Mi leage A BN Br Pitch angle Roll angle Course difference against the destination Video voltage Airspeed Power voltage Heading Ground speed current g1 A T Altitude B16 O oft ek B BA A MAH on Consumption of motor power Ground projector distance to the destination Flying time At this time GPS starts searching the satellite signal The signal intensity symbol at the upper right corner refers to the number of the satellites detected If the signal intensity symbol flashes it means no satellite signal detected or the satellite signal date received by GPS is not reliable and cannot be used as location parameters The searching lasts one to five minutes in case of adequate satellite signal and the time changes in different environment Cautions 1 Please press RESET to zero before taking off The operation will zero altitude distance time and power consumption 2 The meaning of current azimuthal angle of the plane The location of plane is based on the take off as the base point and the rotates from due north from 0 to 360 degree For example if the plane is at the southeast direction the it will display 135 Heading HDG 20 b o O Eaa Home position Position of the plane
6. ane and adjust the servo center servo REV setting Refer to Operation instruction 1 TRIM Trim the infrared ray sensor Refer to Operation instruction 2 Page 2 CRUISE Set cruise airspeed Airspeed value 0 200Km h during auto pilot AIRSPEED when set as 0 the system will not control the airspeed SPEEDMAX Maximal limit of airspeed The air speed of the throttle in PA mode SPEEDLOW _ Lowest limit of airspeed When the air speed of the model plane is lower LIM than the set value the system will not climb to avoid speed loss ELEVON Set elevator aileron Used to control aileron type model plane If choose Y disable the mix control setting on the remote controller ROLL Roll control parameters SEV ANG maximal slope limit at roll PITCH Pitch control parameters SEV ANG maximal angle limit at pitch Description of waypoints Page 1 page 2 DIS Waypoint distance The distance between the Waypoint and the home PIS Mexpointdstnes point setting range 0 5000meters ANGLE Waypoint angle The angle between the line of waypoint and the home ee ua with the due north setting range 0 359 ALT Alinde of waypoint Seting ange 0800 metes Hovering radius The hovering radius with the certain waypoint as the RAD pornn center setting range 0 500 meters DIR Hovering direction L counterclockwise R clockwise Page 3 ON OFF Whether to use the waypoint AUTOWAYPOIN Auto waypoint shift Y Shift to the next wa
7. ations once after the infrared ray sensor 1s properly fitted unless the plane is changed or infrared ray attitude sensor is newly fitted 3 If there is TF card mini SD card and power supply is connected TF card will generate USERID txt file in which 30 digit ID number of the main board will be stored Please keep the number properly for future maintenance and software updating Description of auto pilot 1 Please confirm that infrared ray sensor and airspeed pipe are properly installed and the infrared ray attitude sensor shall not bear large angle deviations from the plane 2 We recommend the clients to use model plane with good stability 3 Flying mode shift shall be connected to any knob ratio channel on the remote controller Under different modes the flying interface will display different information PA auxiliary manual pilot mode AUTOPILOT auto pilot mode RTH Auto return mode At auto pilot mode turn the knob AUTOPILOT to PA and quickly back to AUTOPILOT the system will shift to the next waypoint Auxiliary manual pilot mode Auto pilot mode j Auto return mode Manual pilot mode 4 We recommend to use remote controller with failure protection functions F S function You may set plane pilot mode shift channel fail protection as auto return pilot In this case the plane can automatically return in case of losing control 5 In PA mode the system can keep the course and altitude automatically and the screen
8. utput ial linha ls Supu servo AIL In Aileroninput_ Receiver aileron channel PWM o Z oZ ooo etde hsa tpat fessor sssratoreterns A Ho tn Toone input Reesiver toe hamul ey L O O MOD In Pilot mode Receiver knob channel a between manual control PA shift a RTH SCR In OSD display Receiver knob switch PWM switch channel Cautions 1 Never touch the pressure sensor with anything keep it clean and free from explosion to light 2 Never blow wind by mouth to the air speed indicator in case damage may occur 3 Keep the circuit board away from electromagnetic field such as video projector and remote controller protector 4 Never touch the circuit board with metal in case short circuit may occur 5 Keep the airspeed tube away from propeller movement range at least 1 5 times of the propeller diameter to the fuselage in case deviations may occur to the air speed indicator 6 Please fit the infrared ray sensor to the plain as indicated in the following diagram White arrow gt Two sensors horizontally and directing upward ae vertically installed CYCLOPS FPV ASSISTANT White arrow pp aan the plain head Description of display The main board indicator lamp flashes after power is connected The following picture will appear when you insert TF card Mini SD card If there is not TF card then it will display NO SD CARD FOUND and jump to startup picture automatically after 2 seconds CYC
9. ypoint after the plane reaches T the waypoint N hover as set above the current waypoint The operator needs to turn the knob manually to shift to the next waypoint MAXISCHG Advance distance for Setting range 0 100 meters waypoint shift NOTE The system is in default value at leaving factory The clients need only to set the red bold characters for auto pilot Operations 1 REV reversal setting Cover the upper part Z axis infrared ray of the vertical infrared ray sensor Z axis infrared ray with a hand after proper connections confirmed shift the flying mode to PA mode Then cover the left side and front of the horizontal infrared ray sensor XY axis infrared ray observe whether the aileron is calibrated to the right side and the elevator servo is properly adjusted If not adjust AIL and ELE of REV options If motor is used as the model plane throttle channel the reversal is available for default value The clients only need to set the Nor REV of remote controller throttle channel 2 TRIM infrared ray sensor trim setting After infrared ray sensor is fitted on the model plane put the plane higher than the head in the open space and observe the attitude angle parameters if P parameters is negative number such as 3 you need to adjust P parameters to 3 Repeat the operations and observe P parameters until it becomes 0 Observe R parameters with the methods as mentioned above to trim R parameters You need only conduct the oper

CYCLOPS FPV ASSISTANT V1.0 User`s Manual (Beta Version

Contents

Download Pdf Manuals

Related Search

Related Contents