Dear Client, Congratulations to your new turntable TTT
Contents
1. Dear Client Congratulations to your new turntable TTT Compact TTT C This unit allows analogue play back on the highest level because of compact design and careful engineering in every detail Please follow this manual carefully step by step for getting advantage of all possibilities of fered by your new turntable Please take your time to assemble install and adjust the TTT C carefully Your dealer will be ready to assist you The TTT C is a mechanical precision instrument Please beware of using high forces or hits to this unit Seite 1 8 Vit Turntable 1 Unpacking TTT C The packaging of this unit consists of three layers Please open the main packaging and take out the following items carefully Clamp External charger Power adapter for external charger country specific Ground wire screws Hex key wrenches 5 0 2 5 1 3 Adjusting key WM AWNE Please place these items well ordered to the side so they are ready to be used during installa tion of the turntable After taking out the upper layer completely the second layer of the packaging will be visible It contains the platter Please take out the platter carefully and place it on a suitable base After taking out the second layer of the packaging the last layer will be visible This layer contains the main chassis of the TTT C Please take out the cassis and place it horizontally on a suitable base Seite 2 8 Platter 2 Releasing the trans2. current is needed Therefore the battery will be discharged after 200 hours even if the platter is not turning Please remember to switch the unit off 0 while not in use Weare using most modern LiFePo batteries These accumulators do have no memory effect This means you are free to charge them no matter what the ac tual charge state is The battery can be recharged for at least 1 000 cycles The battery is covered by a PCB circuit to prevent complete discharge which de stroys this type of battery and fault current If the unit has been switched off 0 for a long time period this PCB needs to be reset by the external charger There fore the unit needs to be switched into the charging mode II shortly after sev eral weeks of not using it even if the battery is not discharged The battery pack can provide power up to 1 000 Watts This energy is set free by incorrect handling of the accumulator as well Therefore the battery needs to be exchanged by your distributor dealer only Depending on the charge state the external charger can produce emissions electrical field noise Therefore we recommend to unplug it completely from the power plant and turntable while playing music Seite 6 8 Standby The unit is ready to be started by the push buttons at the front 33 45 The external power supply is disconnected elec trically from the circuit Off The unit is disconnected completely from the internal and ex
3. l can be disassembled by losing the 4 screws 2 Depending on the configuration of your turntable and tonearm the electrical connection has been made already Set the level Place the unit on an even and horizontal base The level of the TTT C can be set by turning the spikes in and out of the main chassis Please use a level gauge to level the unit exactly hori zontal Please make sure at least one of the spikes is tightened fully The spikes are guided not only by a fine pitch thread but by a cylindrical fitting as well Therefore no locking of the spike is needed The maximum range of adjustment is 6mm Interconnect Connect the ground wire deliverd with your TTT C with the jack of the terminal 4 and with the fitting connection of your phono stage Configure the external charger with the country specific power adapter and connect it with the fitting jack 5 of the TTT C Plug the external charger into the electrical socket The exter nal charger can handle all usual input voltage Seite 5 8 5 Internal Power Supply TTT C The TTT C is fitted with a high power battery pack The turntable is driven by the internal power supply only The external charger is to be used for charging the battery only Please refer to the table on the right Important notes A fully charged battery pack will keep the turntable running in playback mode for at least 16 hours Ifthe unit is kept in the standby mode I a small control
4. lease plug the clamp carefully on the spindle of the turntable The clamp is not screwed or tightened but operates with its mass only 8 Cleaning For cleaning the TTT C please use a soft and clean towel The high density inlays of the platter and the clamp shall be cleaned with a wet microfiber towel For this process please use water only neither cleaning nor dissolver liquids Seite 7 8 9 Technical specifications Technical specifications Turntable speed 33 U min 45 U min Wow and flutter at 33 rom DIN45 507 0 06 Rumble 58dB unweighted Weight 16 kg Voltage charger 100 240V 50 60Hz Turntable specification 3 phase motor underneath platter Short belt drive system with flywheel High precision bearing hard chrome plated High density mat between platter and record Decoupling ball element feet Integrated power supply unit Black finish with silver edges Clamp with high density inlay Options Additional tonearm base for exchange 9 10 5 12 LEVI Base air decoupling base Seite 8 8
5. port lock The main bearing of the TTT C is locked during transport to prevent damages to the bearing caused by vibration This locking mechanism lifts the sub platter slightly and keeps it in posi tion To release the transport lock please follow the following steps Release 4x hexagon screw 1 Remove 4x hexagon screw 1 completely Move both locking cylinders 3 out of the sub platter 2 1 2 3 4 Turn both locking cylinders 180 around their axle 5 Replace 4x hexagon screw and tighten them 6 Sub platter incl belt and flywheel shall be free turning now Seite 3 8 3 Installing platter The main platter 1 is bearing freely on the sub platter 2 During assembling please make sure to guide the main platter exactly vertically on the sub platter The main platter has an inlay of a specified high density mat 3 Please take care on this mat for not destroying it during installation 1 Guide the main platter 1 carefully from above on the sub platter 2 2 Make sure the main platter is bearing completely on the sub platter 3 If needed dress the inlay mat 3 around the centre 4 carefully so the record will lay on an absolutely even surface Seite 4 8 4 Installing TTT C Tonearm For assembling the tonearm please follow the manual of the tonearm itself carefully The tonearm base of the TTT C is mounted with 8 screws 1 For soldering the internal wiring of the tonearm the outlet termina
6. ternal power supply The battery keeps its charge state for many months Charging If the external charger is con nected the battery will be charged The charge state is shown on the external charger 6 Setting and Adjusting Speed The two push buttons at the front labelled with 33 and 45 are to be used to start and stop the platter on the speed indicated The push buttons do have an integrated light show ing the actual status of the turntable Blinking single light acceleration phase of the platter Steady Platter turns on the speed indicated Blinking both lights Battery needs to be charged As soon blinking of both lamps starts the battery will rest for at least one hour in playback mode The speed of the turntable was set in our factory using most precise equipment This setting is stable for a long time period If re adjusting is needed use the specific adjusting key 1 deliv ered with the TTT C The adjusting key is set thru the hole at the front of the TTT C and connected to the internal potentiometer Turning the key clockwise will decrease turning it anticlockwise will increase the speed of the platter 7 Clamp The TTT C is delivered with a record clamp designed for this turntable specifically This clamp is working harmonically with the high density inlay of the main platter It reduces vibration and deformation of the record itself and ensures steady contact between platter and record P
Download Pdf Manuals
Related Search