G10F Installation Manual
Contents
1. Enter parameters necessary for sending SMS messages to the users in the menu Text SMS reporting x 15 x Gi0config File About Disconnect F2 F 8 Read F7 pen Last Fa Write FE Open F3 Save F5 Name Telephone Alarm Restore Ti 37068644378 Troubles Te Tests Ta T4 Intemational phone number Example 27068012345 Text SMS reporting Settings i Firmware SMS encoding p ENGLISH WwiIN1252 Send SMS All Object ID Account Mame Users O01 User O01 zone 1 O02 User O02 Zone 2 Partitions 0i Areal 02 Area Dey GIOF SH 000014 Ver 1 62 Connected 11 Telephone Name SMS encoding Object ID Send SMS Enter user phone numbers T1 T2 T3 T4 to which SMS messages will be sent Phone numbers are entered with the international country code but without the sign Select which users will be sent messages after some type of an event occurs Select Alarm Restore to send SMS messages about zone violations restorations event codes E R1XX see Annex 1 Select Troubles to send SMS messages about system operation problems event codes E R3XX see Annex 1 Select Tests to send communication test messages Test via SMS messages event codes E6XX See Annex 1 Select the desired SMS encoding from the list Enter the object name which will be included into the SMS message text Select which messages listed in the table Name will be sent to users via SMS messages Select All to2. TRIKDIS ZTRIKDIS SE z Network Trouble Power GSM communicator G10F v 1 62 Setup Manual Draugystes g 17 LT 51229 Kaunas E mail info trikdis It www trikdis It UI amp OJ CO N O Purpose of the document This document introduces the features of GSM communicator G10F describes its operation parameter setting procedure and usage peculiarities Contents GSM communicator G10F 3 1 1 Operation description 3 1 2 Technical parameters 3 1 3 Equipment 3 1 4 Overall view of communicator G10F 4 1 5 Purpose of contacts 4 1 6 Light indication 4 Communicator setup 5 2 1 Setup procedures 5 2 2 Connection diagrams 6 Setting operation parameters 6 Upgrading communicator firmware 11 Setting operation parameters remotely 12 5 1 Remote communicator programming 12 5 2 Actions after sending an SMS message 12 Remote communicator firmware version upgrade 13 Annex 1 Communicator messages 14 Safety requirements 15 Warranty and limitation of liability 15 1 GSM communicator G10F GSM communicator G10F is used to send fire alarm signals from the protected object to the monitoring station using GSM communication channels Main features messages are transmitted to the monitoring station via GPRS DTMF or using SMS messages messages are sent via the main communication channel or if communication fails via the backup channel information may be sent using SMS message
3. enter the six digit message decryption password default 123456 5 2 Actions after sending an SMS message 1 Open Pcom and right click on the identification number Object ID of the communicator whose parameters you wish to modify J Fie Settings About Control Object state summary Refresh control famba ni ier 4 a an of IV Refresh every fio seconds Refresh Options fla Lost 0 Objects control Remove object Object ID IP Phone number Communication state Level GPRS last ping GPRS ping interval GSM last ping mete Waiting for GPRS message 3 2010 03 23 1 13 31 60 N A a 2 Left click on the G10config button appearing next to the identification number 3 Left click on Connect and Read in the G10config taskbar GPRS connection status Connected will be displayed in the program status bar if GPRS communication session with module G10F is on Operation parameters of communicator G10F are set in the same way as connecting it using the USB cable see section Setting operation parameters 13 5 Click Write once desired parameter values are entered so that they are not moved to communicator G10F 6 Click Disconnect to end the GPRS connection session 6 Remote communicator firmware version upgrade 1 Send a SMS message to the GSM number of the SIM card inserted into communicator GIOF For details see section Setting operation parameters remotely Open Pcom and right click on the identification number Object
4. 1 Overall view of communicator G10F 1 GSM antenna a 2 Terminal block s 3 Indicator Network aa 4 Indicator Trouble gt 5 Indicator Power Ke 6 USB connection for programming 7 SIM card slot 1 5 Purpose of contacts Contact Purpose E 24 V power supply terminal COM General terminal INI 1st input terminal type EOL 10 kQ IN2 2nd input terminal type EOL 10 kQ IN3 3rd input terminal type EOL 10 kQ IN4 Ath input terminal to connect to Dialer terminal in the fire alarm control panel OUT1 1st output terminal OC type no connection OUT2 2nd output terminal OC type communicator operation problems OUT3 3rd output terminal OC type no connection operation opposite to OUT1 1 6 Light indication Light indication Status Description Green light Communicator is connected to a GSM network Network denotes the connection status with the GSM network Trouble denotes communicator operation problems Power denotes power supply status microprocessor operation and programming mode Yellow light Green flashing Yellow flashing O zA G x T MT D Q gt ok lt D O g h Q ya 3 gt Ul ga 1 red flash 2 red flashes 3 red flashes 4 red flashes 5 red flashes 6 red flashes 7 red flashes 8 red flashes Green flashing Yellow flashing in turns A message is being sent Connecting to a GSM network The amount of yellow flashes denotes GSM connection strength No operat
5. Communicator serial number Ver 1 62 Communicator firmware version If Read after connection Restore defaults settings Restore F11 Ver 1 62 Connected Click Read F7 er x Remember Enter the access code default 1234 when prompted and click OK Click Remember if you want the software to remember your access code The prompt window will not appear next time Tick Save access code for software to remember the password and not require for it next time Tick Read after connection for the software to read the data automatically once connected Click Restore F11 to restore to factory settings When prompted click Yes Select Main in the menu and set desired parameters File About Disconnect F2 F8 Read F7 Write F6 Open F3 Save F5 GPRS reporting Text SMS reporting Object ID Jv Hex Settings Firmware SIM Card PIN code MV GPRS ping time 30 3 User code CSD ping time fo a min ees 0 i Admin code SMS ping time zi mn V Test time 24 h Return to primary after 30 Backup reporting after 2 attempts Panel type fi INPUT_ONLY Save access code IV Read after connection Restore defaults settings Restore F11 Dev G10F SN 000014 Yer 1 62 Connected Object ID Field to enter the four digit identification number Hex Tick if hexadecimal numbers will be used while entering the object ID SIM card PIN code Field for SIM card PIN code Leave the f
6. Gl0config 3 Select Connect in the menu 4 Si Fie About Connect Disconnect F2 F8 Read F7 5 x Open F3 Save F5 Open Last Fa Write FB Main GPRS reporting Port Text SMS reporting Settings Firmware Language Allow user to change Object ID SIM Card PIN code Text SMS reporting Settings that may be edited upon connecting with User password COMe v Name Telephone lEngish 3 T01 English T0 T03 T04 Intemational phone number Example 37068012345 Allow user to see and change Settings for connecting Wireless programming phones Enter wireless programming phone numbers using a USB Port COME English Language Click Connect F2 F8 File About Connect Disconnect F2 F a Save access code Dev G1OF SM 000014 Select the USB port to which the communicator is connected in the list Port Note the particular USB port to which the communicator is connected appears only when the two are connected Select the desired working language in the list Language Indicator Power should flash green and yellow in turns when communicator GIOF is connected to a computer Connection status Connected should be displayed in the Gi0config status bar alongside the information about the connected communicator Dev G10F Communicator type SN 000002
7. and upon failure will send messages using the backup communication channel Enter parameters for communication with the monitoring station in GPRS reporting En ao File About Disconnect F2 F8 Read F7 Open Last Fa Write F6 Open F3 Save F5 elie ella Primary reporting GPRS v Backup reporting GPRS x Text SMS reporting Settings Server IP1 address Joprs trikdis t Server IP2 address 62 28 195 126 Firmware or Domain or Domain Port fi 1000 Port 8766 Tel 1 P Tel 2 PO Leave blank if only Text SMS reporting required APN static tele2 I Protocol TRK_TCP v lice Encryption key RAEES Password DNS1 8 8 8 8 DNS2 8 8 4 4 Second backup reporting tel Module events Event Contact ID event code Contact ID restore code a TIME E 700 99 999 R 700 99 999 TEST E 602 99 999 POWER E 302 99 999 R 302 99 999 INI EVENT E 110 99 001 R 110 99 001 IN2_EVENT E 300 99 001 R 300 99 001 IN3 EVENT E 200 99 001 R 200 99 001 vi Dev G10F SN 000014 Ver 1 62 Connected Select the main communication channel via which communicator will send messages to the monitoring station Set GPRS and enter the IP address and the port number of the monitoring station in the fields Server IP1 address or Domain and Port Set DATA and enter the PSTN receiver phone number in the field Tel 1 in order to send Contact ID messages in DTMF tones Phone number is entered with the
8. international country code but without the sign Set SMS and enter the SMS receiver phone number to which SMS messages containing Contact ID event codes will be sent in the field Tel 1 Phone number is entered with the international country code but without the sign Primary reporting Select the backup communication channel via which communicator will send messages if communication via the main one is lost Set GPRS and enter the second IP address and the port number of the monitoring station in the fields Server IP1 address or Domain and Port Set DATA and enter the PSTN receiver phone number in the field Tel 2 in order to send Contact ID messages in DTMF tones Phone number is entered with the international country code but without the sign Set SMS and enter the SMS receiver phone number to which SMS messages containing Contact ID event codes will be sent in the field Te 2 Phone number is entered with the international country code but without the sign Backup reporting Tel 2 Enter the phone number of the monitoring station SMS receiver to which SMS messages will be sent if communication via main and backup channels is lost This option is only allowed when main and backup communication channels are set to GPRS Phone number is entered with the international country code but without the sign Select the message encryption protocol from the list Field to enter the six digit encryption password Password must match t
9. send messages about all events Select Only described to send messages about events that are listed in tables Users Zones Partitions These tables should only be used in exceptional cases Entries in the table Users are linked with the user codes that are used to activate deactivate the alarm system Name of the user will be included in the SMS message if the user activates deactivates the alarm system Entries in the table Zones are linked with the protected zone events Zone name specified in the table will be included in the SMS message when zone is violated restored Entries in the table Partitions are linked with the partitions of the security system into several independently protected areas Area name indicated in the table will be included in the SMS message 6 Click Save F6 to move entered values to the communicator G10F 7 Click Disconnect F8 and unplug the USB cable Save F5 Open F3 Click to save the entered values on the computer A file with an extension gst will be created and may be use in the future as a template to configure other modules Click to open a saved file with gst extension 4 Upgrading communicator firmware Communicator firmware may be upgraded once the manufacturer updates communicator G10F with new operation features 1 Download the newest G10F_vx xx prg file from www trikdis It Note Firmware update files available only for registered users 2 Connect the communicator G10F to th
10. the Product user has not updated their product firmware version on time There may be some technical inaccuracies grammatical and typographical errors in the product manual TRIKDIS reserves the right to edit add and or change the information in the manual 16
11. 01 406 451 R700 Time isn t set E R 100 E R 110 115 E E 110 E R 120 E 121 E R 130 149 E R 144 E R 301 E R 302 309 E R 321 E R 408 E R 409 E 602 E R 700 SMS message text as sent by communicator G10F Event codes are indicated in ECID codes table 15 SMS message text sent to a user MEDICAL PANIC ALARM FIRE PANIC ALARM FIRE PANIC ALARM PANIC ALARM DURESS ALARM ALARM Alarm restore ALARM Alarm Restore AC Power failure on control panel AC Power failure restored on control panel Battery Power failure on control panel Battery Power restored failure on control panel Bell trouble on control panel Bell trouble restore on control panel Phone Line trouble on control panel Phone Line trouble restored on control panel OPEN by CLOSE by Quick DISARM Quick ARM Key switch zone Key switch restored Periodic Test 8 Safety requirements Be sure to familiarise yourself with this manual before using communicator G10F Communicator may only be set up and maintained by trained specialists who possess knowledge about operation of low voltage and signal transmission devices and their safety requirements Communicator G1OF must be set up in limited access areas and in safe distance from sensitive electronic equipment Communicator is not resistant to mechanical effects humidity and aggressive chemical environment 9 Warranty and limitation of liabilities By purchasing the Pro
12. ID of the communicator whose firmware you wish to upgrade Left click on Connect and Read in the G10config taskbar GPRS connection status Connected will be displayed in the program status bar if GPRS communication session with module G10F is on Select program G10config catalogue Firmware Click Browse and select file G1OF_vx xx prg previously downloaded from website www trikdis lt and saved on the computer Click Start to begin the upgrade process whose progress will be displayed in the progress bar Once the progress bar fills up press Disconnect Module will disconnect from receiver and will start firmware upgrade it may take up to 5 minutes Then firmware upgrade is finished the module will reconnect to the receiver and will be available for remote configuration New communicator G10F firmware version bill be displayed in G10config status bar Read section Setting operation parameters if you wish to view or edit operation parameters Click Disconnect to end the GPRS connection session 14 7 Annex 1 Communicator G1OF messages Note Communicator G10F may send messages that are indicated in the operation of communicator G10 Some event codes for example activation deactivation are not available and must not be used Messages sent by communicator G10 Recorded event CID code Event code Text in the Contact ID standard sent to CSP SIA DC 05 1999 09 code table Pp Rio o R100 fF o Ruo Jooo Ao f E R 351 E R 400 4
13. duct the Buyer agrees that the Product is a security system element informing about the status of the system Set up Product does not decrease the possibility of the robbery fire burglary or any other breach of the premises TRIKDIS is not liable in cases of the robbery fire and other breaches of the premises of the Buyer and or the Product user and shall not reimburse the resulting property or non pecuniary damages By purchasing the product the Buyer agrees that TRIKDIS sells a Product that satisfies the requirements of the Buyer TRIKDIS does not guarantee that the Product will operate in the indicated way if the Product is not used in accordance to its purpose and not set up in accordance to the User manual TRIKDIS is not liable for the Product operation malfunctions if they have occurred due to the loss of the GSM GPRS Internet connection or due to a failure in the networks of the connection service provider TRIKDIS does not influence and is not liable for the pricing and costs of the GSM GPRS Internet connection operator services TRIKDIS is not liable for the interruption of GSM GPRS Internet connection services to the Product buyer and or the Product user and the property and non pecuniary damages incurred thereof TRIKDIS is not liable for the interruption in the electricity supply to the Product buyer and or the Product user and the property and non pecuniary damages incurred thereof TRIKDIS is not liable if the Product Buyer and or
14. e computer open G10config and select Firmware in the menu 3 Click Browse and select file G1OF_vx xx prg saved on the computer in the field Open firmware file 4 Click Start F9 Click Disconnect F8 once the progress bar fills up Disconnect the USB cable gt G10config i s Fie About Disconnect F2 F8 Read F7 Write F6 Open F3 Save F5 Main GPRS reporting Text SMS reporting Settings Firmw are Open firmware file O GAMINIAINPROGRAMOS G1 OF G10F_0162 prg Browse Start F9 5 Plug in the USB cable back again Firmware upgrade process lasts between 60 to 90 seconds Wait until indicator Data stops flashing green and click Connect F2 and Read F7 New communicator firmware version will be displayed in the G10config status bar 12 Dev G10F E SN 000014 Ver 1 62 Connected 5 Setting operation parameters remotely Remote setting of communicator G10F operation parameters is possible only when messages are received by the software Pcom Software IPcom may be found on www trikdis It Note Pcom Software is available only for registered users 5 1 Remote communicator programming Send an SMS message to the GSM number of the SIM card inserted into the communicator G1OF in order to set operation parameters of the communicator remotely Upon receiving an SMS message the communicator G10F will initiate a continuous GPRS communication session with software Pcom Wi
15. ete DNS factory values 2 Insert an active SIM card Refer to your mobile network operator with regard to the SIM card It is not recommended to use pre paid SIM cards 3 Attach the communicator into the Position and measures of the holes to be drilled in the casing for control panel casing using M3x6 mounting the communicator and the antenna screws adhesive mounting tape or plastic holder PH 4 Screw the GSM antenna 5 Connect communicator to the fire See section Connection diagrams alarm control panel according to the diagram 6 Turn on the power supply 7 Evaluate whether the strength of the Sufficient level is level 5 5 yellow flashes by light indicator GSM connection is sufficient by Network Use a different type antenna if the GSM connection level looking at the light indicators is insufficient 8 Check whether communicator is A message must be sent and received at the set IP address Check sending messages according to the whether all SMS messages are received if messages are sent to the parameters set during the mobile phone configuration 2 2 Connection diagrams 18 36 VDC 0 wA i Bi GSM 4 Di ye Oi J 2 outputs PGM Fire panel PGM Dialer o Diagram for connecting communicator G10F to the fire alarm control panel Note Input IN4 can only be connected to the fire alarm control panel terminal Dialer Input IN4 power supply voltage will be disconnected if commu
16. he decryption password entered in the receiver software Pcom IP addresses port and phone number encryption protocol and key other parameters may only be submitted by the station manager Protocol Encryption key APN GSM network operator access point name User Login for connection to the GSM network Password Password for connection to the GSM network 10 DNS1 DNS2 Server names of the domains APN user name password and DNS values must be submitted by the GSM connection operator the SIM card was purchased from Module events Communicator events after which messages are sent are displayed in the table below Events E event description R event description TIME Internal clock of the communicator not set TEST POWER Power supply restored to 25 V IN1_ EVENT Input N1 circuit after the short circuit restored IN2_ EVENT Input N2 circuit after the short circuit restored IN3_EVENT Input N3 circuit after the short circuit restored IN4_ EVENT Input N4 circuit after the short circuit restored IN1_TAMPER Input N1 circuit restored after being broke IN2_TAMPER Input N2 circuit restored after being broke IN3_ TAMPER Input N3 circuit broken Input N3 circuit restored after being broke Left click twice on Contact ID event code or Contact ID restore code to edit an event code and enter new values in the new window click OK to check if correct ME x Active Classiticator E Event fio Subgroup js Zone jon OF
17. ield empty if PIN code request is disabled User code Field to enter the user code Only those operation parameters that are allowed to be edited by the administrator can be edited when logging in with the user code Admin code Field to enter the admin code All operation parameters can be edited when logging in with the admin code Also possibilities for editing the operation parameters for those logging in with the user code may be limited Panel type Select the desired input operation mode from the list GPRS PING time Communicator will send GPRS to receiver communication test signals PING in a specified time period CSD PING time Communicator will send CSD to receiver communication test signals PING in a time period SMS PING time Communicator will send SMS to receiver communication test signals PING in a time period Test time Communicator will send communication testing messages TEST to the monitoring station in a specified time period Return to primary after Used if both communication channels to the monitoring station are selected main and backup Enter the time interval value after which communicator will try to restore the communication via the main channel when using the backup communication channel Backup reporting after attempts Used if both communication channels to the monitoring station are selected main and backup Enter the number of times communicator will try to send a message via the main communication channel
18. ion problems Low power supply voltage below 23 V SIM card problem no or wrong SIM card SIM card PIN code problem incorrect PIN code Programming problem Registration to GSM network problem Registration to GPRS network problem No communication with the receiver for more than 300 seconds At least one of the input circuits is broken Power supply and microprocessor are in operation Insufficient power supply voltage below 19 V microprocessor is in operation Programming mode 2 Communicator setup 2 1 Setup procedures Action Notes 1 Set communicator operation Use information laid out in section Setting operation parameters parameters For example to receive all the messages via one channel e g via GPRS it is enough to see Gi10config Main window Enter communicator object identification number into the field Object ID amd PING signal and Test message sending periods into fields GPRS PING time and Test time see Gi10config GPRS reporting window Select the GPRS transmission channel in the list Primary reporting enter static IP address of the monitoring station and the port number in the fields Server IP1 address or Domain and Port enter the access point name APN of the GPRS network in which the SIM card that is inserted into the communicator operates in the field APN and a six digit encryption password that must match the IP receiver message decryption password in the field Encryption key Note Do not del
19. nication between the monitoring station and the message receiver does not work for more than 300 seconds For this reason control panel e g Smart Line or identical will indicate a problem connection with the monitoring station is lost Event gt Input type EOL voltage at the end of the line EOL 10kQ An event is formed once external circuit status changes m short circuit in the external input circuit Event m voltage is restored to 10 kQ after short circuit Event restore m external input circuit is broken Sensor Tamper m voltage is restored to 10 kQ after being broken Sensor Tamper Restore 3 Setting operation parameters Operation parameters of communicator G10F are set using software Gi10config Software may be found on www trikdis It 1 Connect the communicator GIOF to a computer using a USB cable Note A USB driver must be installed on the computer A USB driver installation window Found New Hardware Wizard should appear on OS MS Windows during the first cable connection between the communicator and the computer Download OS MS Windows USB driver installation file USB_COM inf from the website www trikdis It Select Yes this time only when prompted and click Next A new window Please choose your search and installation options will open Click Browse and select the location where USB COM nf is saved To finish the USB driver installation follow remaining installation wizard commands 2 Run
20. reless programming phones Hame Telephone Intemational phone number Example 37068012345 If the phone number of the authorised person was entered in the field Wireless programming phones previously during the setting of operation parameters the communicator will initiate a GPRS communication session only upon receiving an SMS message from that specific phone number U u SMS message text _ refers to a gap between words in an SMS message CONNECT 9874 SERVER 100 100 100 100_PORT 1000_APN supplier_USR user_PSW psw_ENCR enc where CONNECT 9874 SERVER 100 100 100 100 PORT 1000 APN supplier USR user PSW psw ENCR enc start command Enter the four digit access code default 1234 SERVER enter the IP address of the computer with installed software Pcom PORT enter the serial port number of the program Pcom APN enter the access point name APN of the GPRS network in which the SIM card inserted into the communicator operates Enter APN _ if the network provider does not require an access point name USR enter the login user name of the GPRS network in which the SIM card inserted into the communicator operates Enter USR _ if the network provider does not require an access point name PSW enter the login password of the GPRS network in which the SIM card inserted into the communicator operates Enter PSW _ if the network provider does not require an access point name ENCR
21. s if GPRS connection fails sent messages match protocol Contact ID codes ability to send SMS messages to the mobile phones of up to 4 users operation parameters and firmware version may be upgraded remotely operation parameters are set using G10config VVVVVV V 1 1 Operation description Communicator G10F is connected to relay outputs programmed in the fire alarm control panel Communicator supports a continuous monitoring of their statuses and once they change forms and sends messages Messages are sent to the monitoring station and or to the user mobile phones Communicator sends messages about the events restores in input IN1 IN3 external circuits to the contacts indicated during the programming Input IN4 is used to indicate communication problems by connecting it to the fire alarm control panel INIM Smart Line or identical Input IN4 power supply is discontinued if connection between the communicator and the receiver is lost for longer than 300 seconds Communicator sends connection testing signals TEST periodically and may perform a continuous control of communication with the receiver using PING signals Communicator may send messages via backup channels if the main communication channel fails If two GPRS communication channels are set and communication with the receiver is lost information to the monitoring station may be sent using SMS messages Messages may also be sent to the mobile phones of 4 users Every fire alarm con
22. trol panel message is attributed with a comprehensible SMS message text SMS messages may be divided among different users according to the type of the sent message Status of the communicator output OUT2 changes in case of an operation problem Statuses of outputs OUT1 OUT3 change if a message fails to be sent for longer than 300 seconds Communicator controls the power supply voltage and upon larger than allowed changes sends adequate messages and signals using the light indicators Messages in the monitoring station are received using the receiver with installed software Pcom computer with installed IPcom Win IP receiver RL10 server with installed IPcom_Linux 1 2 Technical parameters DC 20 V 36 VDC or AC 14 V 25 VAC 60 100 mA on standby up to 500 mA while sending data Power supply Used current GSM modem frequencies Memory Input Input for fire alarm control panel indication management Output Parameters setting Workplace Measures 1 3 Equipment Communicator G10F Adhesive mounting tape 10 cm Resistor 10 kQ 850 900 1800 1900 MHz up to 60 messages 3 input type EOL 10 kQ 1 INIM Smart Line or identical to manage communication status indicators 3 OC type commutate DC up to 50 V and current up to 100 mA using a USB port remote connection via IPcom temperature from 10 C to 50 C relative humidity up to 80 when 20 C 65 x 79x 25mm 1 pc 1 pc 3 pc 1 4
Download Pdf Manuals
Related Search