Kramer SL-1 User Manual
Contents
1. is Site CTRL compatible enabling remote control and management of the AV equipment e Production studios rental and staging Each package includes the following items e The SL 1 Master Room Controller e Kramer K Config Configuration software e Power supply and this user manual 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual e Use Kramer high performance high resolution cables No operator serviceable parts inside unit Use only the Kramer Electronics input power wall adapter that is provided with the unit WET Disconnect power and unplug unit from wall before installing or removing the device or servicing unit 1 GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Matrix Switchers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Products 2 Download up to date Kramer user manuals from our Web site at http www kramerelectronics com 1 Getting Started 2 1 Quick Start This quick start chart summarizes the basic setup and operation steps Step 1 Connect the inputs and outputs see section 5 D Connect the relay2. panel of the SL 1 controller as shown in Figure 3 RS 232 Device SL 1 RS 232 lr Ground TAT GRLA O Figure 3 RS 232 Connection 6 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the SL 1 Master Room Controller 5 2 Connecting the Ethernet Port The Ethernet connection of the SL 1 allows you to perform all control functions of the SL 1 over the Internet using a PC running the Kramer Site CTRL control program To connect the SL 1 to a network 1 Connect the Ethernet port of the SL 1 to the Ethernet port on a network hub or network router via a straight cable with RJ 45 connectors 2 At the other end connect the Internet to a PC running Site CTRL After connecting the Ethernet port you have to install and configure it For detailed instructions on how to install and configure your Ethernet port see the K Config Configuration Guide 5 3 Connecting the K NET Port The K NET port is wired as shown in Figure 4 K NET PINOUT K NET B A12V G Red 12V Black GND Figure 4 K NET Pinout Connection 1 Available for download at the Kramer Web site www kramerelectronics com Operating the SL 1 Master Room Controller 6 Operating the SL 1 Master Room Controller You can operate your SL 1 using e A K Net compatible remote controller or auxiliary control panel To operate your device using an external K Net device see the K Config Configuration Guide e The optional RC 4 Infra
3. using STP cable for twisted pair products For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply before opening servicing Caution Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000543 REV 3
4. Jack Connects to a remote infrared sensor 10 NET LED illuminates when the Ethernet link is active 1 First disconnect the power cord and then connect it again while pressing the ETH Factory Reset button The unit powers up and loads its memory with the factory default definitions and erases all stored presets 2 K Net is a proprietary Kramer protocol for interconnecting Kramer units 3 The ground connection is sometimes connected to the shield of the RS 485 cable in most applications it is not connected KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the SL 1 Master Room Controller Feature Function 11 K NET LED llluminates when the K NET is active 12 RS 232 Tx Rx LEDs llluminates while transmitting receiving on an RS 232 port 1 to 2 13 RLEDs llluminates when an IR port is active 14 RELAYS LEDs llluminates when an relay is active 1 to 3 15 SRVC DIP Switch Slides down for service use only slides up for normal operation 16 K NET TERM DIP Switch Slides down for K NET termination slides up for not terminated 17 PROGRAM USB Connector Connect to a computer for unit configuration and firmware upgrading 4 1 Using the RC 4 IR transmitter You can use the optional RC 4 IR transmitter to control the machine via the built in IR receiver on the front panel or instead via an optional external IR receiver The external IR receiver can be located 15 met
5. Kramer Electronics Ltd USER MANUAL Model SL 1 Master Room Controller Contents Contents 1 Introduction 2 Getting Started 2 1 Quick Start 3 Overview 4 Your SL 1 Master Room Controller 4 1 Using the RC 4 IR transmitter 5 Connecting the SL 1 Master Room Controller 5 1 Connecting the RS 232 Interface 5 2 Connecting the Ethernet Port 5 3 Connecting the K NET Port 6 Operating the SL 1 Master Room Controller 7 Technical Specifications Figures Figure 1 SL 1 Master Room Controller Figure 2 Connecting the SL 1 Master Room Controller Figure 3 RS 232 Connection Figure 4 K NET Pinout Connection Tables Table 1 SL 1 Master Room Controller Functions Table 2 SL 1 Master Room Controller Technical Specifications LV Y ANDAA USP WON m eS FA Introduction 1 Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function Thank you for purchasing the Kramer TOOLS SL 1 Master Room Controller which is ideal for e Controlling multimedia rooms such as classrooms auditoriums conference rooms and so on and
6. cs hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOW LONGIS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHOIS PROTECTED Only the first purchase customer may enforce this warranty WHAT IS COVERED AND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty 1 Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the Web site www kramerelectronics com 2 Any product on which the serial number has been defaced modified or removed or on which the WARRANTY VOID IF TAMPERED sticker has been torn reattached removed or otherwise interfered with 3 Damage deterioration or malfunction resulting from i Accident misuse abuse neglect fire water lightning or other acts of nature ii Product modification or failure to follow instructions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removalor installation of the product vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cable
7. ers away from the machine This distance can be extended to up to 60 meters when used with three extension cables Connecting the SL 1 Master Room Controller To connect the SL 1 as the example in Figure 2 illustrates do the following 1 Connect the RELAY terminal block connectors as follows Connect RELAY and 2 to the blinds Connect RELAY 3 to the screen 2 Connect the IR outputs as follows Connect IR OUTPUT 1 to the DVD player 1 Connect IR OUTPUT 2 to the DVD player 2 3 Connect the RS 232 ports as follows Connect RS 232 port to the projector Connect RS 232 port 2 to the plasma display 4 Connect the IR sensor as follows Connect IR INPUT to an IR sensor Connect the Ethernet port to a network Connect the K NET port to any RC device with K NET 1 Model C A35M IRR 50 2 Model C A35M A35F 50 3 Switch OFF the power on each device before connecting it to your SL 1 After connecting your SL 1 switch on its power and then switch on the power on each device Connecting the SL 1 Master Room Controller RC 4 br IR Sensor N FS IO Blinds Relay IR DVD Player Y Projector Y IR Plasma Screen Al DVD Player Display Figure 2 Connecting the SL 1 Master Room Controller 5 1 Connecting the RS 232 Interface To connect an AV device to the SL 1 connect the RS 232 9 pin D sub port on your device to the RS 232 terminal block on the rear
8. f the product loss of time commercial loss or 2 Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and lightindustry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and lightindustry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION B gt Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment Use the supplied DC power supply to feed power to the machine B Please use recommended interconnection cables to connect the machine to other components FCC and CE approved
9. red remote control transmitter To operate your device using the infrared remote controller see the User Manual packed with the remote controller e A PC running Site CTRL control software To operate your device using Site CTRL see the Site CTRL and Web Access Online User Guide 7 Technical Specifications The SL 1 technical specifications are shown in Table 2 Table 2 SL 1 Master Room Controller Technical Specifications INPUTS 2 RS 232 and K NET on terminal block connectors Ethernet on an RJ 45 connector 1 infrared sensor 1 infrared on a 3 5mm mini jack connector 1 USB for programming OUTPUTS 2 infrared and 3 relays 36V AC or DC 2A 60VAC maximum on non inductive load on terminal block connectors DEFAULT IP SETTINGS IP number 192 168 1 39 Mask 255 255 0 0 Gateway 0 0 0 0 INDICATORS LED indicator for each function POWER SOURCE 12V DC 2A from power supply or 12V DC over K NET connection DIMENSIONS 12cm x 7 2cm x 2 4cm 4 7 x 2 8 x 1 0 W D H WEIGHT 0 3kg 0 7Ibs ACCESSORIES Power supply OPTIONS RK 3T 19 rack mount RC 4 remote controller external IR receiver and IR receiver extension cables 1 Available for download at the Kramer Web site www kramerelectronics com 2 Specifications are subject to change without notice 3 Model C A35M IRR 50 4 Model C A35M A35F 50 8 KRAMER SIMPLE CREATIVE TECHNOLOGY LIMITED WARRANTY Kramer Electroni
10. s Connect the IR outputs Plasma DVD Player Display Step 2 Connect the power Step 3 Operate the machine Operate via the RC keypad IR remote control K NET or ETHERNET 2 KRAMER SIMPLE CREATIVE TECHNOLOGY Overview 3 Overview The SL 1 is a highly versatile controller that acts as an all in one extended remote control panel for control of A V equipment especially projectors and associated equipment in any room such as classrooms boardrooms or auditoriums It streamlines operations and simplifies control by integrating audio video and computer video sources into a centralized system The SL 1 Master Room Controller features e 2 bidirectional RS 232 ports to control AV equipment such as projectors LCD and PDP displays power amplifiers switchers and scalers e 3relay contact closure ports to control other room items related to the AV system such as raising and lowering drapes the screen or the projector e IR control 1 input 3 5mm and 2 outputs terminals blocks e IR Learning that learns commands from any IR remote e Compatibility with Kramer Site CTRL software for network remote control and management over the Ethernet port e AK NET control channel for connecting compatible user interfaces and supplying power and control data over a single cable e A USB port for loading device firmware e Flexible control using Ethernet K NET IR sensors and external IR commands To achieve the be
11. s or accessories used in conjunction with the product WHAT WE WILL PAY FORAND WHAT WE WILLNOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removal or installations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 To obtain service on you product you must take or ship it prepaid to any authorized Kramer service center 2 Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OFIMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for 1 Damage to other property caused by defects in this product damages based upon inconvenience loss of use o
12. st performance e Use only good quality connection cables e Position your Kramer SL 1 away from moisture excessive sunlight and dust 1 Available from Kramer Electronics on our Web site at http www kramerelectronics com 3 Your SL 1 Master Room Controller 4 Your SL 1 Master Room Controller Figure 1 and Table 1 define the unit RE IR RS 232 K NET M a 3 11 62 Runi G Rand G B AIN 12V DC OOOO IR INPUTS r STATUS 1 ETHERNET DEFAULT NET K NET pres p e p era Oo 200000000 Master Room Controller Figure 1 SL 1 Master Room Controller Table 1 SL 1 Master Room Controller Functions Feature Function 1 RELAYS Terminal Blocks Connect to low voltage relay driven devices from 1 to 3 2 IR Output Terminal Blocks Connect to IR emitter cables from 1 to 2 3 RS 232 Terminal Blocks Connect to the RS 232 devices from 1 to 2 4 ETHERNET RJ 45 Connector Connects to the PC or other serial controller through computer networking LAN 5 DEFAULT Pushbutton Press to reset to factory default definitions Ms IP number 192 168 1 39 mask 255 255 0 0 gateway 0 0 0 0 6 K NET Terminal Block PIN GND is for the ground connection PIN B and PIN A are for RS 485 and PIN 12V is for powering the unit 7 12V DC Connector For supplying power to the unit 8 IR IN Sensor and LED Accepts IR remote commands 9 R INPUT 3 5mm Mini
Download Pdf Manuals
Related Search