User Manual - VIAIR Corporation
Contents
1. IT DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL DAMAGES AS RESULT OF MISUSE OR ABUSE Your Vital Air Source 15 EDELMAN IRVINE CA 92618 TEL 949 585 0011 FAX 949 585 0188 www viaircorp com2. Do not over tighten if your port fittings are made from brass since brass threads can be stripped The fittings need to be only airtight c Always release air from tank before servicing or repairs d Wear safety glasses or goggles when operating this product WARNING DRAIN TANK AFTER EACH USE FAILURE TO DRAIN TANK AND REMOVE CONDENSATION WILL CAUSE TANK TO RUST PREMATURELY a To remove any accumulated condensation inside the tank bleed pressure from tank until pressure is approximately 5 PSI to 20 PSI b Drain water from tank by opening the drain cock valve c If drain cock valve is plugged release all air pressure from the tank Remove and clean the drain cock valve then reinstall d After water has been drained close drain cock IMPORTANT Please observe air tank s Date of Manufacture stamped on tank leg Replace air tank 2 to 5 years from date air tank was first used or use the date of manufacture as reference Your adherence to air tank draining guidelines will determine the replacement date of your air tank RUSTED TANKS CAN CAUSE EXPLOSION OR FATAL INJURY Discard tank immediately if tank is rusted internally NOTE When using safety pressure relief valve point the safety pressure relief valve away from your body Use the pull ring on the safety relief valve to open the relief valve to vent any pressure inside the tank before attempting to service tank USER MANUAL 0 5 GALLON AIR TANK 0 5 GALLON AIR TANK PARTS L
3. IST Washers 2 pcs T MOODD Hex Nuts 2 pcs Vibration Isolators 2 pcs Brass Inserts 2 pcs Mounting Bolts M11 x 35mm 2 pcs Locking Washers 2 pcs See Fig 1 for Mounting Hardware Assembly C q Fig 1 TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE S CORRECTIVE ACTION Tank loses air pressure 1 Air leaks from fittings Locate leak by applying soap amp water solution Tighten fittings as needed Tank leaks 1 Pinhole from internal rusting of tank 1 Replace tank immediately Can t get air from tank to inflate tire 1 Low tank pressure USER MANUAL Tank pressure must exceed tire pressure Increase tank pressure LIMITED WARRANTY VIAIR Corporation warrants this product when properly installed and under normal conditions of use to be free from defects in workmanship and materials for a period of one year from its original date of purchase To receive warranty service or repair please contact VIAIR Corporation Returns should be made within one year of the date of purchase after a Return Goods Authorization RGA number has been assigned by VIAIR Corporation To obtain RGA fax a copy of your receipt to 949 585 0188 For complete warranty details please visit www viaircorp com warranty PLEASE NOTE THIS WARRANTY COVERS PRODUCT DEFECTS ONLY
4. Your Vital Air Source 0 5 GALLON AIR TANKS PART NO 91005 IMPORTANT It is essential that you and any other operator of this product read and understand the contents of this manual before installing and using this product SAVE THIS MANUAL FOR FUTURE REFERENCE USER MANUAL 0 5 GALLON AIR TANK Please read this instruction manual carefully prior to operating this product Pay particular attention to the CAUTION and WARNING statements in this manual Failure to comply with these instructions could result in personal injury or property damage Retain these instructions for future reference NOTE Your air tank comes with two 1 4 NPT ports To ensure safe and trouble free use of your air tank we strongly recommend that you install a drain cock and a safety pressure relief valve IMPORTANT a VIAIR tanks are rated for 150 PSI maximum working pressure Do not over pressurize Overpressuring may result in death or serious injury b Tank is not intended to be used as a breathing device c Always wear ANSI approved safety glasses when operating air tank d Bleed pressure from tank after each use and before servicing or adding attachments e Use only attachments rated for 150 PSI maximum CAUTION DO NOT PRESSURIZE YOUR TANK UNTIL YOU HAVE INSTALLED ALL NECESSARY PORT FITTINGS AND ACCESSORIES a Apply sealant to threads of fittings prior to assembly and hand tighten each part then use a wrench for airtight connection b
Download Pdf Manuals
Related Search