User Manual
Contents
1. 28 UP 2007 series Super Speed Universal Programmer user manual Batch Program c This function can Auto run speediness and easy operate can auto judge the chip in or out auto run mass program by pre set Statistic parameters amp Click device Mass production mode to run it Finish the necessary settings on the option window and enter Then jump out Insertion checking window you just insert the device it will auto program by pre set options when program finished it will prompt remove the device massage insert another device go on f the device you selectis ok the greed Good LED will light and the inside buzzer will BI once too Sound alam switch must ON If failed e g erase failed will display error information at the same time red error LED light buzzer will BIBI twice to alarm The batch production will auto stop when the current count overcomes target count or current failure overcomes maxi failure lt gt Batch procedure is for mass verify too You should confim all the insertion check short circuit check device ID check and verify function are set of Option No need other Settings You can run one or at most 8 set UP 2007 by one computer synchronously or asynchronously 8 set UP 2007 can not only program the same device with the same data but also program different device with different data especially for mass production UP 2007 series Super Speed2. This option includes Address Option HEX Start Address The start address for UP 2007 to blank check read program verify compare to the devices End Address The end address for UP 2007 to blank check read program verify compare to the devices Buffer Size Its size is as the same as the device capacity in normal Autoinc Start Autoinc End The automatic serial Number end address It is the end address of the device too amp Autoinc Value 25 UP 2007 series Super Speed Universal Programmer user manual Functions introduction Autoinc Format Binary Format of binary star value is 0 0 FF w ASCII Hex Format of hex s as 0 F ASCII Decimal cw User defined Statistic Option Current Count Set the current count its value is less than the target count Target Count Set the Target count and the batch program will auto stop by this value being counted Its available range is 0 100000 ce Current Failure Set the current allowable Failure it is less than the max Failure value Max Failure Set the max Failure and the batch program will auto stop by this value being counted Program Option VCC V Set the VCC voltage Ssupply to device arrange as 1 25V 6 5V Up or down by 5 VCC only within its allowable windage VPP V Set the VPP voltage express program voltage as 1 25V 17 5V Up or down by 5 VCC only within its allowable windage ce Pulse nS Set the program impulse band withi
3. E data v998ck e Disable File Format Mode From Buffer Address e Clear Buffer with Zeros 0x00 Binary x 0 e Clear Buffer with Ones Oxff default setting Buffer Mode Buffer Size ALL y 410000 File Note Image Dblclick to Open Please make a note of the file in here Pic 14 15 16 UP 2007 senes Super Speed Universal Programmer user manual 17 Functions Introduction File name Show the file name and directory path File format mode The file format for saving and its default format is binary system bin From buffer address Data copied into disk from this address amp buffer mode Save the verified data from the buffer as one file ALL is all file be loaded Buffer size The buffer size for loaded files also is device size 8 Click select button the select Current Device window jump out as Pic 15 f Select Current Device Search Package S20C3B v Manufacto C00d0000 6S9S50660 Devices O00G0060 GE28F 320038 UBGA4B BGAI 20 8999969090 GE28F320C3B UBGA4B BGAI 20ANY OO9S90006 GT28F320C38 UBGA48 BGA120 00009006 GT28F320C3B UBGA48 BGA120ANY RC28F320C3B EBGAG4 EBGAG4 TE28F320C3B TSOP48 TSOP56 Device Information Type FLASH Man code 89H Dev code 88C5H dapter E BGA126 Size 266666X16H Note This device includes 128bit protection register Please configs mi emer Seven columns in the screenshot Search In
4. Address Display the current address You click the HEX it will show the corresponding current address in current address zone Function Button Copy copy the appointed address data of buffer to new address 7 Click the edit button the edit the memory buffer window following as Pic 17 Search search the appointed data as text serial figures or letters Next performs the next search for the search string in search Swap swap the data sequence for example the original sequence is 00 01 02 9860000 C 66 9F E5 99 19 AG E3 68 16 80 E5 74 00 OF ES 03 we exchange their sequence from the second bit into 01 00 03 02 6666616 FC 1D AGB ES 66 16 86 ES C 66 9F ES CO 1C AB ES H i ifi H adla AAE a a e Done finish the buffer data display or modification 66660636 66 66 9F ES 58 16 9F ES 66 16 86 ES 58 66 OF ES k 6666646 MC 16 9F ES 66 16 86 ES 56 66 9F ES 46 16 OF ES 6666656 66 16 86 ES 48 66 9F ES 34 16 9F ES 66 10 86 ES Pic 16 f Edit the Memory Buffer Data 6666676 66 GF 66 EB 46 D7 AGB ES C 66 OA EA GE FO AB E1 0000080 000 FO AG E1 18 61 OA 26 C 66 OA 8C 74 OO 66 8C aa l A eacer nc Gaus ec ear ance This function can copy the device data into the buffer ein anaes ane Four options in device Read of main menu 86606606 65 66 54 E1 FA FF FF 6A 61 66 14 E3 OB 46 84 16 Z read read all the data into memory buffer OOOOHEG 61 66 15 ES B 56 85 10 62 66 15
5. ES 69 56 85 18 l 86000F 6 03 56 C5 E3 16 60 56 E2 8C 10 B4 28 8C 10 A5 28 P read NOR FLASH just read NOR flash data read SecSi Hi ROM only read the Hi ROM data Current Address on ee ee If there is the Protection Register inside the device when it run read the Protection Pic 17 Register will be read automatically and saved at the last address in buffer 19 20 UP 2007 series Super Speed Universal Programmer user manual Functions Introduction To check if the device is in blank state this is dependent on the data manual If yes the data are all FF There are six options in device Blank of main menu Blank blank check whole device e Blank Nor FLASH blank check the NOR FLASH Blank SecSi Hi ROM blank check the Hi ROM e Blank NAND FLASH blank check the NAND FLASH e Blank last 1MB blank check the last 1MB data of device e Blank last 2MB blank check the last 2MB data of device This function write the data from the buffer into the chip it Contain many automatic operation test RAM erase blank check and program verify program the Hi ROM Protection Register and program NAND FLASH etc Set these in option menu Four options in device Program of main menu e Program program all including the Hi ROM Protection register NOR FLASH and NAND FLASH Program NOR FLASH only program NOR FLASH Program SecSi Hi ROM only program this
6. This wizard helps you install software for Use the check boxes below to limit or expand the default search which includes local UP 2007 Super Speed Universal Programmer paths and removable media The best driver found will be installed Search removabl dia floppy CD ROM c L If your hardware came with an installation CD Include this location in the search gt or floppy disk insert it now click here What do you want the wizard to do Don t search will choose the driver to install Install the software automatically Recommended Install from a list or specific location Advanced click here Click Next to continue Choose this option to select the device driver from a list Windows does not guarantee that the driver you choose will be the best match for your hardware Pic 6 Pic 7 08 UP 2007 senes Super Speed Universal Programmer user manual 09 Installation and Configuration Found New Hardware Wizard Select the device driver you want to install for this hardware Select the manufacturer and model of your hardware device and then click Next IF you Ae have a disk that contains the driver you want to install click Have Disk Show compatible hardware Model UP 2007 Super Speed Universal Programmer A This driver is not digitally signed Tell me why driver signing is important Pic 8 vA If cant contact the UP 2007 when open the UP 2007 software the error can t
7. Universal Programmer user manual How to Fix Device Please insert the device into the socket or adapter by the application request Fix it with upside if there arent any special requests by the application lt UP 2007 can auto sense and self check when it checks short circuit bad contact or device insertion remove works with little signal and special bus won t damage for any device But please dont program when the software has alarmed you Product Information c Contact UP 2007 well to the computer click about item you can read the main information about this programmer as Pic 23 e Software VER UP 2007 version you are using Hardware VER UP 2007 box version Serial NO UP 2007 product SN exclusive SN to one box Datecode UP 2007 produced date Sales Area seller or company of UP 2007 e USB POWER USB power supply voltage Copyright Information product copyright information T About UP 2007 Software VER 9 3 8 Hardware YER JT512 Serial NO 611079 459056 Datecode 2007 01 30 Sell s Area USB POWER USB2 0 5 10 UP amp UP Copyright C 2001 2007 Guangzhou JingTian Corp Ltd Le HTTP 7 Y UP48 COM 2B EMAIL SUPPORT UP48 COM e TEL 8620 3423 5716 FAxX 8620 3423 5743 Q DEVISER BailinTian BJT 30 UP 2007 senes Super Speed Universal Programmer user manual Service and support gt UP 2007 designed for flexible hardware configuration you can just update your instrument softw
8. as Pic 13 it will save the data in the buffer to disk Select the format for file opening normally the software can auto choice it Save file From File Mode Save in data Open the specified part from the file 7 choices d Sass All default setting This loading all content of the file to buffer My Recent Documents Even 1st of 2 This loading every even byte to buffer as 0 2 4 6 Odd 2nd of 2 This loading every odd byte to buffer as 1 3 5 7 lst byte of 4 This loading the bytes 0 4 8 12 to buffer e 2nd byte of 4 This loading the bytes 1 5 9 13 to buffer e 3rd byte of 4 This loading the bytes 2 6 10 14 to buffer e 4th byte of 4 This loading the bytes 3 7 11 15 to buffer To Buffer TEE Specify the buffer address for file loading from the from file mode data The sub Save astype Al Fies C x options are the same as from file mode selections My Network l From File Address Pic 13 Data loaded into buffer from this address To Buffer Address Save method is the same as saving files in Windows system Input the specified Data are filled into buffer from this address file name and save directory after click save the save buffer to a file popup Buffer Size as Pic 14 The buffer size for loading files 7 Eraser Clear Buffer Before Loading the File SR Before loading file into buffer clear up the buffer data
9. connects with UP 2007 message will alarm you and it suggests you to select the right USB portto connect the UP 2007 as Pic 9 The default USB port is 0 You can Set the USB port setting by yourself too in the setting menu Select USB Port Select USB Port GS USB Port 0 USB Port USB Port 2 USB Port 3 USB Port 4 USB Port 5 USB Port 6 Pic 9 Connect UP 2007 series Super Speed Universal Programmer user manual Software Operation This chapter helps you understand the whole process of IC program The content includes the interface details the step of the programming A Click start gt program gt UP amp U P gt UP 2007 or the UP 2007 shortcut on the desktop run UP 2007 exe the interface is as Pic 10 K UP 2007 SERIES SUPER SPEED UNIVERSAL PROGRAMMER J1512 File Device Project Setup Tools Language Help About 2 hH E SKMM JE 02990 Save Select ID Rdi Read Blank Prog Verify Comp Erase N Prot Option Device Information a Device GE28F326B3B UBGAS8 BGA126 Size 266666HX16 Type FLASH Adapter BGA126 Pin 48 Max Failure 5 Socket CD E UCC 3 66U Manuf Code 89H Total Time 204 8 Check Sum 3FCGG66G6H UPP 11 56U Device Code 8897H File Name The memory buffer no data ON OFF RESET E an Connected Mode EA Update 2007 08 16 7 Sell Area USB2 0 5 10 Total Produce information column 5 1 1 Thumbnails Explanation v There are six p
10. eee ane nee Di 6 8 Program RE Di 6 9 Verifye ED 6 10 COMpare gt e s eE e E 22 Gol Wie pase ater coset scat ahuos cena ac ar an tenccnaner meets 99 Ba E PRAM saniesei tee ume enema ments hens o eds DA 613 ells Cie ee re re are 93 6 14 Project cS DA 6 15 OPtions gt 555 EE EE 25 Batch Programming gt gt ss eee e e e errer C eee eee se 29 Zi Mass I 29 7 2 One Computer Connect Many Programmers 20 Howto FIX eT 30 Product Imfonmnatlone A ee eee ee eee 320 Update and Tech Support ee gt s eee eee ee e e e eee 31 Guaranty 55 CEE EE CE EEE 20 UP 2007 series Super Speed Universal Programmer user manual 03 Packing List UP 2007 series Super Speed Universal Programmer 1pc e USB Connecting Cable 1 line e Installation Software CD ldisc e User Manual lpiece Guaranty Card lpiece e Adapter As the purchasing list e Size 270mm x 165mm x 62mm System Requirement USB port computer auto adapt USB2 0 or USB1 1 or with PCI to USB adapter 64MB memory minimum Windows 98 98SE ME NT 2000 2003 XP operation system CD ROM 40MB hard disk space or more UP 2007 series Super Speed Universal Programmer user manual Features and Configuration S USB2 0 port compatible to USB1 1 port With high speed CPU program and arithmetic running in CPU providing the exactitude program tum and speed High speed program program and verify the GE28F 320B3B 32Mb in 9 5 seconds only Pro
11. model different BGA adapter P G A B e Indicators c UP 2007 with two sets indicators orange and green red as Pic 1 Orange P Box powered on or contact Green Red G E Operation indicators program OK turn green or program failed turn red USB connect port as Pic 2 lt gt Power switch as Pic 2 Pic 1 Pic 2 05 UP 2007 series Super Speed Universal Programmer user manual Installation and Configuration NOTE In order to connect the programmer easily and quickly please connect the hardware after installing the software e Installation three steps set up software hardware and USB drive First please install the software without connect UP 2007 and restart the PC then set up the hardware The last set up the USB drivers it will run auto Make Sure normal installation Please only set up the software once even you will do the one to all one PC connects most 8 set UP 2007 The hardware configuration and USB drivers must be done separately Put the CD into the CD ROM and will auto run just do as the wizard asks if no auto run please click the SETUP EXE of CD and run the set up as Pic 3 Do as the thumbnail asks and it is ok please restart the PC after set up UP 2007 Super Speed Universal Programmer Install Wizard Exit the Install Guide Guangzhou JingTian Electronics Co Ltd Address FL4 NO 18 Wanhua St Lanzhou Rd Guangzhou City Guangdong PRC Tek 6
12. the Protection Register of FLASH device After confirmation for the device with Protection Register the application will inform that the device is with Protection Register for example Intel 28F320C3B device Click Prot button will popup as Pic 20 If the device is without Protection Register the button is invalid To press related button you can run related functions as display read write Protection Register As Pic 21 When the application read and save the device data the Protection Register data will be auto read and saved at the same time and its address is in the last 17 bytes 23 UP 2007 series Super Speed Universal Programmer user manual Functions Introduction The 81H 84H is the unique device identifier code read only The 85H 88H is the user programmable OTP code you can program once this section Ca al gt 128F320C3 Series Protection Settings Page 1 m 128 bit Protection Register Settings Unique Device Identifier Read Only User Programmable OTP 85H FFFF 86H FFFF 87H FFFF BBH FFFF Cancel Default Pic 21 m Protection Settings IV Protect Register Save Project Save the current work environment to specified project Click project Save Project to run this function and input the filename and folder then save it The file includes current device selected buffer data operation options setup and device options settings The project file
13. 1EB USB2 Enhanced Host Controller 24DD UP 2007 Super Speed Universal Programmer USB Root Hub USB Root Hub USB Root Hub USB Root Hub USB Root Hub UP 2007 series Super Speed Universal Programmer user manual Installation and Configuration d If the USB driver found other USB device drive cant connected the UP 2007 please re install it Open the device management right click the USB DEVICE and select update driver and step by step operation as pic5 8 Device Manager File Action View Help gt Aa e Ra H E IDE ATA ATAPI controllers ae Keyboards Mice and other pointing devices 89 Network adapters 4 Other devices HY Ports COM amp LPT 9 Processors ES Sound video and game controllers System devices Universal Serial Bus controllers InteR 82801EB USB Universal Host Controller 24D2 InteR 82801EB USB Universal Host Controller 24D4 Intel R 82801EB USB Universal Host Controller 24D Intel R 82801EB USB Universal Host Controller 24DE InteR 82801EB USB2 Enhanced Host Controller 24DD Se eT Data Liiva USB Root USE Root Dabe USB Root Uninstall USB Root Scan for hardware changes USB Root Properties Launches the Hardware Upoocewrreorarorcnie oaeeo oer Pic 5 Found New Hardware Wizard Found New Hardware Wizard Please choose your search and installation options Search for the best driver in these locations
14. 8620 3423 5716 34236797 Fax 8620 3423 5743 Ne Pic 3 06 UP 2007 senes Super Speed Universal Programmer user manual 07 Installation and Configuration Connect the UP 2007 to the PC with USB connect cable if no USB port please add one PCI USB socket Dont use the USB HUB or the too long USB extemal cable Then tum on the UP 2007 switch and then power LED tum orange 7 Please setup the USB driver for UP 2007 A After software installation restart your PC if every thing is done correctly the PC will find UP 2007 USB driver auto The successful USB setup will show as Pic 4 you can find that control panel gt system device manager Universal Serial Bus controllers UP 2007 super speed universal programmer If the USB driver set up failed or the PC cant connect the UP 2007 please delete the UP 2007 super speed universal programmer and re install it Device Manager File Action Yiew Help t H Ra eA RA HE IDE ATAJATAPI controllers Ye Keyboards B Mice and other pointing devices H E Network adapters Other devices 9 Ports COM amp LPT d Processors Sound video and game controllers System devices S Universal Serial Bus controllers Intel R 82801EB USB Universal Host Controller 24D2 Intel R 82801EB USB Universal Host Controller 24D4 Intel R 82801EB USB Universal Host Controller 24D Intel R 82801EB USB Universal Host Controller 24DE Intel R 8280
15. GuangZhou JingTian Electronics Co Ltd Address FL4 No 18 Wanhua St Nanzhou Rd Guangzhou City Guangdong PRC Tel 8620 34235716 Fax 8620 34235743 Website http www up48 com http www up48 cn E mail Support up48 com UP amp UP WSR E NK C E E UP 2007 SERIES SUPER SPEED UNIVERSAL E PROGRAMMER GRE igh reserved E User Manual 01 Thank you for purchasing UP 2007 series Super Speed Universal Programmer Please read this manual carefully before your installation The manual explains all the necessary features of the UP 2007 series Super Speed Universal Programmer and please read this manual Carefully it will help you to use our product normally and please keep this manual for future reference Itis very important products function that manual introduce in this manual UP 2007 series Super Speed Universal Programmer short for UP 2007 On the manual The information in this manual is subject to change without notice please get the news and software update of UP 2007 from your reseller or visit our website Http www up48 com All rights reserved of GuangZhou J ingTian Electronics Ltd This manual forbid in whole or part be copied or translated without allow from GuangZhou J ingTian Electronics co Ltd To different computer system the Interface in this manual may be different Tech Support Please visit our website and BBS http www up48 com and http www up48 co
16. acts as a macro eliminating the need to go through each procedure during future programming sessions 8 Open Project Click project Open Project to run the function According to the file change device buffer data and operation option etc 24 UP 2007 series Super Speed Universal Programmer user manual Functions Introduction T Click Option button open the Operation Procedure Options window as Pic 24 here is the GE28F320C3B option setting Please dont change any default settings unless you are very familiar with the UP 2007 programmer Operation Procedure Options Address Option HEX Program Option Other Option Start Address 0 VCCIV 3 00 Alarm Prompt EndAddress 3FFFFF VPPV 11 50 C Reload Buffer Buffer Sizei 400000 Pulse nS 300 LJAdd Pulse to Retry Autoine Start 3FFFFC Timeout uS i29 Ee 1 hety 7 L C Auto Check RAM on MCP Autoinc Endi 3FFFFF Sas Operation Option C Auto Write Hi ROM SecSi Sector Autoinc Value 1 insattion Check C Auto Write NAND FLASH on MCP Shert Circuit Check Enable UP EXPLORER Autoinc Format Binary ASCII Hex Blank Check ASCII Decimal Erase O User defined Blank Check after Erase M Program Verify Option Statistic Option DEC Verity re ee Current Count I Memory Protect O Twice VCC 10 Target Count C Auto increment Current Failure Verify after Read Max Failure Pic 22 Device ID Check Once
17. are to support new devices c Tech support e Website Http www up48 com get free software for updating e Consult your reseller You can gethelp and support from your reseller too Mail support support up48 com e Atany time you mailed us you should get reply in time e Hotline service 8620 3423 6737 3423 5743 fax e Our hotline will give you on time service too lt Special support and application for new device can apply for support For the information of hardware change functions update new devices support without inform please get by upper methods 31 UP 2007 series Super Speed Universal Programmer user manual Guaranty Guaranty range UP 2007 programmer the USB connecting cable CDs and adapters is out of guaranty e The following situations is out of guaranty 1 Damaged by unusual usage as broken drown or naturalness 2 un authorized maintenance or refit 3 un authorized reselling 4 without necessary and available invoice and guaranty document Guaranty period From the buying date 1 year free exchange 3 years for free maintenance over 3 years repair with the cost of charging the material Guangzhou J ingTian Electronics Co Ltd Guangzhou J ingTian Electronics Co Ltd setup in 2001 It is a professional of UP amp UP series programmers developing designing and producing company We are provide best quality and high technology of programmers applied in phones maintenance home
18. arts of the UP 2007 Interface as Pic 10 Current Count 1 Target Count 200 Current Failure 0 1 Menu and Toolbar It is for all functions such as open files save files select device test device ID edit buffer program compare erase and setting options The menu and down menu same function as the tool bars 10 UP 11 2007 series Super Speed Universal Programmer user manual Software Operation 2 Operation Massage lt Show the operation and result of the program and distinguish them by different colors Blue common operation Green right operation Red error massage and the massage with gt gt is the last indication 3 Device Information lt gt Show the detail device information which you selected as type size adapter and device ID Please check all these information carefully before program the device in case of error ce Device Device type as GE28F320B3B type is GE28F 320B3B UBGA48 BGA120 The UBGA48 is the package the BGA120 is the adapter for it ce Size e Size of device it is use Hex of measure w Type e Type of device such as FLASH EEPROM MCU etc Adapter e Choose the right adapter type Pin Device pins number for example GE28F320B3B with 48 pins VCC and VPP Z Power supply voltage and program voltage for the device c Manuf Code and Device Code The device code and its manufactory code Check Sum e The total of the data i
19. electronics service and IT communication UP amp UP programmers have been sold all over the world Especially the Southeast Asia Arabia Africa and Europe We can offer not only more reliable products but also more professional and satisfactory service to everyone We have one dream UP amp UP 32
20. for short circuit grey is for empty as Pic 16 7 When it show without red or blue click the OK button UP 2007 senes Super Speed Universal Programmer user manual UP 2007 series Super Speed Universal Programmer user manual Functions Introduction Functions Introduction Insertion Checking Six columns for the window NOTE Please put the FLASH into the blue cross with its writing heading up If it was put in the wrong way there will be a red square frame come forth You must put it in the right way otherwise the FLASH cannot read and writ normally Move the cursor to the Frame Socket on the left and Frame 4dapter on the right the PIN name will come forth in the Ee A D D R E S S middle IPIN will show the PIN number of the frame on the left Show the address information of buffer section data Itis corresponding to every origination Adapter BGA120 address line of the hex column The second digit of the first line must be 00 Click the line and you can input the specified address a HEX wa Display the buffer data the buffer data is hex you can modify it within hex 0 9 A F Badness F AS C Il Display buffer data with ASCII the non ASCII data are denoted by ASCII cant be modified You can modify them just through changing HEX amp Scroll bar Drag the scroll bar or click the up down arrow of the bar or press Page UP and Page Down of keyboard you can check the buffer page quickly Current
21. grammer support a lot of devices include NAND FLASH EEPROM RAM test etc FLASH choice automatism just press F5 keyboard Choice automatism to non confirmed FLASH type e BGA adapter with programmer support 0 75 0 8MM pin pitch devices need nT change the adapter or base in programming e Once done for FLASH NAND FLASH HLR OM and RAM test Z Synchronously providing pictures for adapters bases pins and devices type with devices PDF files e Auto test short circuit or bad contact of devices with intuitionist graphics e Error test automatism program in error it will alarm you add impulse or voltage to retry auto saving the devices cost e Advanced FIFO communication methods full auto check during program it makes your box and programming safe and correct e Batch program mode automatism detection tech operation automatism Any new device support can be update from our website by yourselves itis free Asynchronous one to all program with one computer you can run at most 8 set UP 2007 e works in WINDOWS 98 98SE ME NT 2000 XP 2003 with Chinese and English interfaces both Z Guaranty period programmer can be exchanged free in one year free repair in three years 04 UP 2007 series Super Speed Universal Programmer user manual Features and Configuration e Socket lt UP 2007 works with one BGA adapter and AB sockets as Pic 1 BGA adapter is used for 0 75mm 0 8mm pin pitch BGA devices different
22. just erase the last 1MB data of device Erase last 2MB just erase the last 2MB data of device 22 UP 2007 senes Super Speed Universal Programmer user manual Functions Introduction Select the RAM you will test press test button after you confirmed the RAM number as picl19 8 If the RAM is in good condition it will inform you Test OK or it will alarm with gt gt Test failure UP 200T SERIES SUPER SPEED UNIVERSAL PROGRAMMER J1512 File Device Project Setup Tools Language Help About Pu See 0495 2 4 Open Select LD Edit Read Blank Test Veri Prot Option Connecting Use USB2 6 486MHzZ mode connected with Programmer CYPRESS CY62147CU36 GUBGA4S8 SRAM BGA126 Testing Test Success At 3 33MHZ 1 65Second Testing gt gt Test Success At 3 33MHZ 1 65Second Device Information Device CY62147CU36 GUBGA48 SRAM BGA126 Size 40666HX16 Current Count 0 Target Count 200 Current Failure 0 Type SRAM Adapter BGA120 Pin 48 Socket CD E UCC 3 660 Manuf Code None Check Sum 7F86666H UPP 3 66U Device Code None File Name The memory buffer no data ararn Max Failure 5 Total Time 4 2 5 Connected Mode Ver 9 3 8 Update 2007 08 16 Sell Area USB2 0 5 26 Total 4 A Pic 19 As the RAM on FLASH the application will test it automatically If you want to test it separately please click in device test RAM of main menu Read and write
23. lect of main menu the select current device window will jump out input the device part number or all from the screen then click OK button or double click the device to confirm your selection 2 Put Device Open the adapter put the chip into the adapter correctly 3 Check Device ID c Click ID button or press F4 of keyboard test the device ID and the contact or Short circuit at the same time 12 UP 2007 series Super Speed Universal Programmer user manual Software Operation 4 Backup Data lt Click Read button then click OK button it will copy the device data into memory buffer when it finish you may go to the memory buffer click Edit button will jump edit buffer window check if the data is loaded correctly 5 Save Data amp Click the Save button the data be saved to disk for future use 5 2 2 Program Device Data Program device data operation step is Select ID O pen P rogram 1 Select the Device amp Click on select button or device select of main menu Same as the backup device data select operation 2 Check Device ID lt Same as the backup device data check device ID operation 3 Open Data File Click open button to select a data file to be loaded 4 Program Data amp Click Program button it is auto operation which automatically execute the operation of device step by step normally include Test RAM Blank_ check Erase Program verify etc s
24. m bbs Here you can get more news with our product technology free update and download Resellers support Your reseller will give you support at the same time wherever you are Tech support mailbox support up48 com At any time you mailed us you should get reply in time Tel 8620 3423 6737 Fax 8620 3423 5743 Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 5 Chapter 6 Chapter 7 Chapter 8 Chapter 9 Chapter 10 Chapter 11 Packing LIST 555 ee teeee teeters eee eees B System Request a Z Features and Configuration sese e 3 2 a Iain ear Feenu eteacaoce 999 990 so roc cece bac cou 00 0000 000 070 3 3 2 Programmer Figuration ese C C C eee D Installation and Configuration e 6 4i Software Installationc T 4 2 Hardware Conniauraiion gt esse eee eee ee e 7 4 3 USB Driver Set Up gt gt gt 5 55 ee ret tee eee eee teres E AA CO MmmuUIMCAlON POM seting e e 9 Software Operation eee e C C tenets eee e ee ees 10 5 1 Description of Interface gt s ee ee ee e reer eee 10 5 1 1 Thumbnails Explanation eetere 10 5 2 Quick Ellie tee eee soc occcoe son sacra soc e sc 12 5 2 1 Backup Device Data see 12 5 2 2 Program Device Dala sse eee 13 Functions Introduction e eee A G oe se sles E E E oe 16 oI Selec a einai eats T E yay hearse I7 6 4 ID contact badness short circuit test 18 pE BUIS ee ee ee 19 66 Pead e e eee su caren couse sd cewne coe rcumes oes 20 6 7 Blackcheck e acre a
25. n 20 5000ns ce Timeout uS The overtimes is the max time for programming one byte unit is microsecond uS Operation Option e Insertion Check Check the contact between UP 2007 and device during program If during the procedure there is bad contact of device pins will have error especially it may damage the PROM or OTP device 26 UP 2007 senes Super Speed Universal Programmer user manual Functions Introduction Short circuit Check Check the short circuit during program Suggest tick it Otherwise program must be in error Device ID Check Check the device code and its factory code suggest tick it Blank Check Check if the device is in blank state suggest tick it Erase Erase the device before program For new suggest tick it c Blank Check after Eerase Blank check again after erase operation the default is tick it Program Write the data from the buffer into the device amp Verify Verify the device after program It can verify the device data correct VS buffer data The default is yes Memory Protect If protect on device after programming and verifying Auto increment serial number If create the automatic SN The auto SN is numbered in special address of the device normally at the end address as the production serial number If you tick yes after program the system will add one accumulative SN for it by auto increment function amp Verify after Read If verify after read well and the default is ye
26. n buffer zone as hex 4 Statistical Window Display the batch program process Current Count Target Count Current Failure Max Failure and the total time of every operation Except the total time function the statistical window is working for batch process only If the icon hided the statistical window is invalid Count Switch e On or off count function if ON the left icon is visible Otherwise invisible UP 2007 series Super Speed Universal Programmer user manual Software Operation Indication Switch Onor off the inside buzzer sound for UP 2007 ON the icon is visible otherwise invisible Reset Clear up the records of current count Total Count the normal program times including the batch program and single program Only you re install the UP 2007 clear the counter zero 5 File Information ce When you click open one file it will show its name and directory and show the reading status when it read the data from the buffer section 6 Product Column ce Show working status software version info software update date info reselling info USB port version USB2 0 USB1 1 USB power supply voltage and total counting lt Make sure UP 2007 is properly connected with the PC and communication successfully with the PC 5 2 1 Backup Device Data A Backup device data operation step is Select ID Read Save 1 Select the Device Click on select button or device se
27. put the chip number directly all or parts letters to select the device quickly The input number for the chip must be in sequence for example GE28F320C3B you can input all or just input 320 or 20C3 or GE28 but the 32B or GE8F or 28320 is invalid input The search condition should be according to the search column and device type UP 2007 series Super Speed Universal Programmer user manual Functions Introduction Manufacto Display the candidate factories name Click any the name this column will show us the relative device types you will select Device Display the candidate device Device information Display device information as type capacity manufacturer ID device ID and its adapter it help you select the right device and adapter to the unusual device its special information you can read here too Package Display the selected device package picture e Type For easily search and select devices here we classified them into followed groups ALL all types default setting FLASH EEPROM EPROM PROM 6 MCU e PLD RAM DRAM TTL CMOS Click D button test the device ID and the contact or short circuit at the same time If the short circuit or bad contact of the device occurred the ID error alarm window will popup It will show us the direct picture for the socket and adapter contact or short circuit green pins are goodness red pins are badness blue pins are
28. s Other options S Alarm Prompt Tick it and it will give you some related help and settings Reload buffer Auto save the buffer section data when you close the application When run application next time will auto save and auto load buffer c Add Pulse to Retry The application will auto inform you to try again by upping the pulse if the first device flash failed For old devices we suggest you tick it Add VCC to Retry This function will auto retry after upping the VCC if the first step failed UP 2007 series Super Speed Universal Programmer user manual Functions Introduction Auto Check RAM on MCP Auto check the RAM inside MCP device before program the device we suggest you enter it cw Auto Write Hi ROM SecSi Sector Auto read and write the Hi ROM SecSi sector when program We suggest you enter it Auto Write NAND FLASH on MCP If auto read and write the NAND FLASH inside the device during the program we Suggest you enter it ce Enable UP EXPLORER Select this item open or save files the same as window XP EXPLORER just for J T series Verify Option c Twice VCC 5 Verify twice first with the 95 VCC second with 105 VCC to verify Twice VCC 10 Verify twice first with the 90 VCC second with 110 VCC to verify Please check if the device can be tested under this VCC before use this function If not support please verify with Twice VC C 5 or once Once Verify once only with the original VCC
29. section Program NAND FLASH only program NAND FLASH Compares the buffer data to that of the device data if ok it means that buffer data Similar device data Four options in device Verify of main menu e Verity verity all including the SecSi Hi ROM NAND FLASH and Protection Register Verify NOR FLASH just verify NOR FLASH e Verity SecSI Hi ROM only verify this section e Verify NAND FLASH only verify NAND FLASH 21 UP 2007 series Super Speed Universal Programmer user manual Functions Introduction Compare the data of device and buffer data one by one Different from verify the compare will go on even it has got different data until the user stops it or compare all data A Three options in device Compare of main menu Z Compare compare all the data in device with buffer as Pic 18 Comparing Progress Pic 18 Z Compare SecSi Hi ROM only compare the corresponding data in this section with buffer Z Compare NAND FALSH just compare SecSi Hi ROM data v Erase the device data and then device is empty EEPROM doesn t need to execute this operation Six options in device E rase of main menu Erase erase all data including the SecSi Hi ROM or protection register NAND FLASH Erase Nor FLASH erase the NOR FLASH Erase SecSi Hi ROM just erase the Hi ROM Erase NAND FLASH only erase the NAND FLASH e Erase last 1MB
30. teps When it Is finished OK data is copied into chip 13 UP 2007 series Super Speed Universal Programmer user manual Functions Introduction This chapter tell you details of function of the programmer 2A Click open button the open file window popup as Pic 11 Open file Look in data BES My Recent Documents Desktop File name V998c Files of type All Files C C Open as read only My Network d Pic 11 Now you can selecta data file to be loaded itis two data types HEX and BIN generally data types use all file After your choice the file the loading a file to buffer window following as Pic 12 normally you neednt change any setting Loading a File to Buffer File Name EAdata vagac File Format Mode From File Address Binary 0 From File Mode To Buffer Address ALL U To Buffer Buffer Size ALL 410011 Clear Buffer Before Loading the File Clear Buffer with Zeros Clear Buffer with Ones ODisable O yon Sea File Note Without a Image The data file without a note Pic 12 14 UP 2007 senes Super Speed Universal Programmer user manual UP 2007 series Super Speed Universal Programmer user manual Functions Introduction Functions Introduction s File Name Show the file name and directory path File Format Mode 8 Click save button the save file following
Download Pdf Manuals
Related Search