Home

4/8/16/24/32 CHANNEL H.264 DVR - Sunsky

1. the setting of this item is not changed 2 MOTION ENABLE Press UP or DOWN button on the front panel to move the cursor to the MOTION ENABLE line at the MOTION setup menu Press LEFT or RIGHT button to turn on or off the motion detection function 3 SENSITIVITY Press UP or DOWN button on the front panel to move the cursor to the SENSITIVITY line at the MOTION setup menu Press LEFT or RIGHT button to select the motion sensitivity from level 0 lowest to level 7 highest 4 MOTION AREA 1 Press UP or DOWN button on the front panel to move the cursor to the MOTION AREA line at the MOTION setup menu Press ENTER button to display the MOTION AREA setup screen After setting motion area if record resolution CIF 1 2D1 D1 has changed it needs to set motion area again for new record resolution The MOTION AREA setup screen displayed as below 2 3 4 5 6 7 At the MOTION AREA setup screen press MENU button on the front panel to display a setup menu Press UP or DOWN button to move the cursor to the SELECT line and press ENTER button to exit the menu and begin setting motion area Press UP DOWN LEFT or RIGHT button to move the cursor to a starting position of motion area Press ENTER button on the front panel then press UP DOWN LEFT or RIGHT button to select desired
2. RIGHT UP or DOWN button on the front panel to move the cursor to the MATRIX button Press ENTER button on the front panel to switch matrix At the MENU MATRIX setup menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the CAMPOWER button Press ENTER button on the front panel to turn on the camera power Press ENTER button again to turn off the camera power Mouse 1 At the PTZ SET menu click on the MENU button to display PTZ MENU MATRIX setup menu and enter PTZ menu setting mode 2 At the MENU MATRIX setup menu move the cursor to the MONITOR frame Turn the middle button of mouse to set MONITOR address to 1 or other number It is only used for matrix operation if it supports PTZ matrix protocol 3 MENU a At the MENU MATRIX setup menu click on the MENU button to enable PTZ menu setting Click on the MENU button again to disable PTZ menu setting b At the MENU MATRIX setup menu if PTZ menu function is enabled click on the MENU UP M DOWN M LEFT or M RIGHT button to move the cursor to up down left or right direction at the PTZ menu c At the MENU MATRIX setup menu if PTZ menu function is enabled click on the M ENTER button to enter PTZ sub menu Click on the M ENTER button again to exit PTZ sub menu 4 Others a Atthe MENU MATRIX setup menu click on the ALARM button to start alarm search b Atthe MENU MATRIX setup menu clic
3. RIGHT UP or DOWN button to move the cursor to LEFT UP arrow LEFT DOWN arrow RIGHT UP arrow or RIGHT DOWN arrow press ENTER button to operate pan tilt in relevant direction Note Only keep pressing ENTER button to control pan and tilt function When this button released the system will stop pan and tilt control function 3 Press LEFT RIGHT UP or DOWN button to move the cursor to ZOOM MINUS and ZOOM PLUS icon press ENTER button to control zoom near and far function Press LEFT RIGHT UP or DOWN button to move the cursor to FOCUS MINUS and FOCUS PLUS icon press ENTER button to control focus near and far function Press LEFT RIGHT UP or DOWN button to move the cursor to IRIS MINUS and IRIS PLUS icon press ENTER button to control iris close and open function 4 Press AUTO button on the front panel to enable PTZ AUTO control function Or press LEFT RIGHT UP or DOWN button to move the cursor to AUTO PAN button at the menu press ENTER button to enable PTZ AUTO control function The AUTO PAN button at the PTZ control menu is selected and word AUTO PAN will become yellow color Press AUTO button again to exit PTZ AUTO control function and word AUTO PAN will become white color S Press LEFT RIGHT UP or DOWN b
4. UP or DOWN button on the front panel to move the cursor to the BITRATE line at the NETWORK setup menu Press LEFT RIGHT button to select the bit rate of network h264 stream 2 The stream bit rate can be selected to HIGHEST HIGH STANDARD and LOW The higher the bit rate set the higher network image quality get and the slower speed the network connecting has 11 MOBILE PORT Press UP or DOWN button on the front panel to move the cursor to the MOBILE PORT line at the NETWORK setup menu Press LEFT RIGHT button to select the mobile port 12 IE PORT Press UP or DOWN button on the front panel to move the cursor to the IE PORT line at the NETWORK setup menu Press LEFT RIGHT button to select the IE web port 3 8 BACKUP Menu Setup Connect USB device to the USB port of DVR Press MENU button on the front panel to display MAIN MENU during the live display mode Press UP DOWN LEFT and RIGHT buttons to select BACKUP button in the MAIN MENU and press ENTER button to enter BACKUP setup menu Press CANCEL button to exit submenu without saving The BACKUP setup menu displayed as below 1 DISK DEVICE USB CHANNEL ALL CHANNEL START 2011 01 19 16 END 2011 01 19 17 TOTAL 4 262 MB DISK If the USB or SATA DVDRW device is connected to this DVR press LEFT or RIGHT button on the front panel to move the cursor
5. 2 The system pre recording time is 1 second 4 FPS 1 Press UP or DOWN button on the front panel to move the cursor to the FPS line at the RECORD setup menu Press ENTER button to display the FRAME RATE setup menu The FRAME RATE setup menu displayed as below ERAMERATE OFX CH2 25 CH3 25 GROUP TOTAL 100 4CH 5 6 T FRAME RATE sasamane agaran uu 3 WM H3 25 CHA CH5 25 CH6 Ch7 25 CHS 25 CH9 25 CH10 CH 25 CH12 25 CH13 95 CH14 CH15 25 CH16 25 AUTO TOTAL 4007 400 16CH 2 Press LEFT or RIGHT button on the front panel to move cursor to the AUTO line at the FRAME RATE setup menu Then press MENU button to turn on or off auto FPS setting 3 When setting AUTO to off at the FRAME RATE setup menu press LEFT or RIGHT button on the front panel to select a channel at the FRAME RATE setup menu and press UP or DOWN button to set the frame rate of the channel Press ENTER button to exit the FRAME RATE setup menu 4 For 24 32 CH DVR only CIF resolution and this item can not be set QUALITY 1 Press UP or DOWN button on the front panel to move the cursor to the QUALITY line at the RECORD setup menu Press LEFT or RIGHT button to select the quality of recording image 2 The image quality can be selected to HIGHEST HIGH STANDARD and LOW The higher the image quality set the bigger the HDD size used BITRATE 1 Pres
6. ALL if one item display it means that this feature item of each channel is different When saving the setting if the item selected the setting of this item is not changed 2 RESOLUTION 1 Press UP or DOWN button on the front panel to move the cursor to the RESOLUTION line at the RECORD setup menu Press LEFT or RIGHT button to set the recording resolution 2 When setting it to CIF the total frame rate is 400fps for PAL and 480 fps for NTSC of 16CH DVR 600fps for PAL and 720 fps for NTSC of 24CH DVR 800fps for PAL and 960 fps for NTSC of 32CH DVR 200fps for PAL and 240 fps for NTSC of 8CH DVR 100fps for PAL and 120 fps for NTSC of 4CH DVR When setting it to 1 2 D1 the total frame rate is 200fps for PAL and 240 fps for NTSC of 16CH DVR and 100fps for PAL and 120 fps for NTSC of 8CH DVR and 100fps for PAL and 120 fps for NTSC of 4CH DVR When setting it to D1 the total frame rate is 100fps for PAL and 120 fps for NTSC of 16CH DVR and 50fps for PAL and 60 fps for NTSC of 8CH DVR and 50fps for PAL and 60 fps for NTSC of 4CH DVR 3 For 24 32 CH DVR only CIF resolution and this item can not be selected the total frame rate is 600 800fps for PAL and 720 960 fps for NTSC 3 PRE RECORD 1 Press UP or DOWN button on the front panel to move the cursor to the PRE RECORD line at the RECORD setup menu Press LEFT or RIGHT button to turn on or off the pre recording function
7. Seite tetas Tics it us WAN SET leman Lnd M EE Dd ie DOH H 5 fy 5 5 9006 I I ds 4 32 CH DVR 1 CAMERA IN CH1 CH32 2 AUDIO IN CH1 CH16 3 AUDIO OUT 4 LIVE MONITOR OUT 5 VGA OUT 6 RJ 45 ETHERNET 7 RS 485 PTZ AND ALARM INPUT 8 DV12V POWER IN 9 SPOT MONITOR OUT For 16 24 32 CH DVR 10 GROUND Note For 32 CH DVR there are 2 spot monitor output SPOTI is for 1 16 channel SPOT is for 17 32 channel 1 4 Rear Panel Connection 16CH DVR for example CAMERA T CAMERAS ui ap VIDEO IN AUDIO IN AUDIO QUT RIAS WGA OUT RS485 1 18CH ALARM DC 12V MIC 1 MIC16 TZ 16 CH DVR Milla aRM OUT ALARA No 1 No 16 Alarm signal input For 32CH DVR there are 1 16 alarm input No No No 17 18 19 20 ake NL NAE sak PAA Alarm output GND Ground Alarm output N C 1 Normally Closed Alarm output N O 1 Normally Open Alarm output COM1 Common Alarm output N C 2 Normally Closed For 24 32 CH DVR Alarm output N O 2 Normally Open For 24 32 CH DVR Alarm output COM2 Common For 24 32 CH DVR RS 485 A RS 485 B 1 5 Remote Controller NUMER BUTTON Press the desired camera number button you wish to display on the monitor 10 11 12 13 14 15 16 17 18 4 Repeat pressing this button to speed up playback backward at the speed of X2 X4 o
8. Upgrade mode USB upgrade DVDRW upgrade for 8 16 24 32CH DVR network upgrade Support TCP IP DHCP and PPPOE IE browser monitoring Network viewer tool for monitoring playback setup upgrade and log viewing Support email UPNP NTP DNS and DDNS supply a free DDNS for DVR Triplex function simultaneous recording playback network viewing Telemetry network control live view playback recording parameter setting and so on Support zoom function for both live and playback mode Support live and playback video hide Support video covered Support administrator and normal user management Frame rate in the live display mode 4CH 120fps NTSC 1O0fps PAL SCH 240fps NTSC 200fps PAL 16CH 480fps NTSC 400fps PAL 24CH 720fps NTSC 600fps PAL 32CH 960fps NTSC 800fps PAL Frame rate in the recode mode 4CH CIF 120fps NTSC 100fps PAL 1 2D1 120fps NTSC 100fps PAL D1 60fps NTSC 50fps PAL SCH CIF 240fps NTSC 200fps PAL 1 2D1 120fps NTSC 100fps PAL D1 60fps NTSC 50fps PAL 16CH CIF 480fps NTSC 400fps PAL 1 2D1 240fps NTSC 200fps PAL D1 120fps NTSC 100fps PAL 24CH CIF 720fps NTSC 600fps PAL 32CH CIF 960fps NTSC 800fps PAL I IH TABLE OF CONTENT INSTALLATION 1 1 Packing Detail 1 2 Front Panel Controls 1 3 Rear Panel Connectors 1 4 Rear Panel Connection 1 5 Remote Controller 1 6 Installation Process OPERATION 2 1 Power On 2 2 Power Off 2
9. DOWN button on the front panel to move the cursor to the FACTORY RESET line and press ENTER button to display the WARNING box The WARNING box as below SYSTEM SETUP WILL INITIALIZE CONTINUE a eo Press ENTER button on the front panel to load the factory default setting 10 LANGUAGE Press UP or DOWN button on the front panel to move the cursor to the LANGUAGE line and press LEFT RIGHT button to select system language The DVR language can be selected as ENGLISH CHINESE RUSSION FRENCH ITALIAN GERMAN SPANISH PORTUGUESE TURKISH THAI HEBREW GREEK VIETNAMESE 11 SPOT MONITOR For 16 24 32CH DVR 1 Press UP or DOWN button on the front panel to move the cursor to the SPOT MONITOR line at the SYSTEM setup menu Press ENTER button to display the SPOT MONITOR setup menu The SPOT MONITOR setup menu displayed as below CHANNEL MODE ROTATION TIME OFF 2 Press UP or DOWN button on the front panel to move cursor to the CHANNEL MODE line at the SPOT MONITOR setup menu Then press LEFT or RIGHT button to select the display mode for spot monitor HEXA FULL QUAD NINE Press UP or DOWN button on the front panel to move cursor to the ROTATION T
10. press this button to power on the DVR again For Mini 4CH DVR in the playback mode press this button to enter different playback control mode 16 A UP button After pressing MODE button press A UP button to select last camera displaying on the screen Press this button to move the cursor up to the next line in the setup menu In PTZ operation mode press this button to move the cursor up to select function 17 V DOWN button After pressing MODE button press W DOWN button to select next camera displaying on the screen Press this button to move the cursor down to the next line in the setup menu In PTZ operation mode press this button to move the cursor down to select function 18 LEFT button During the live display mode Repeat pressing this button to select the different display mode FULL CHANNEL PIP QUAD 9 SPLIT and 16 25 36 SPLIT Press this button to move the cursor in left direction in the setup menu In PTZ operation mode press this button to move the cursor left to select function For Mini 4CH DVR in the playback mode press this button to select different playback control mode PLAY PAUSE BACKWARD FAST FORWARD STEP FORWORD 19 49 RIGHT button During the live display mode Repeat pressing this button to select the different display mode 9 SPLIT QUAD PIP FULL CHANNEL and 16 25 36 SPLIT In the playback mode press this button to enter step forward playback pres
11. 10 SYSTEM MAINTENANCE SYSTEM sMAINTEnANCE kiti RESTART ON SETTINGS EVERY MONTH DATE WEEK TIME 1 Press UP or DOWN button on the front panel to move the cursor to the SYSTEM MAINTENANCE line at the RECORD setup menu Press ENTER button to display the SYSTEM MAINTENANCE setup menu 2 When setting RESTART to ON it needs to set the date and time The system will restart automatically when the same date and time come as the setting 3 4 MOTION Menu Setup Press MENU button on the front panel to display MAIN MENU during the live display mode Press UP DOWN LEFT and RIGHT buttons to select MOTION button in the MAIN MENU and press ENTER button to enter MOTION setup menu After setting press MENU button to save the setting Then exit the submenu and main menu Press CANCEL button to exit submenu without saving The MOTION setup menu displayed as below MOTION MOTION ENABLE SENSITIVITY MOTION AREA POST RECORD TIMI BUZZER TIMI ALARM TIME SAVE EXIT 1 CAMERA CHANNEL Press UP or DOWN button on the front panel to move the cursor to the CAMERA CHANNEL line at the MOTION setup menu Press LEFT RIGHT button to select the channel to set Select ALL to set all channels When selecting ALL if one item display it means that this feature item of each channel is different When saving the setting if the item selected
12. 2 When setting it to OFF the system PTZ function is disabled The default PTZ protocol is PELCO D 5 PTZADDRESS 1 Press UP or DOWN button on the front panel to move the cursor to the PTZ ADDRESS line at the CAMERA setup menu Press LEFT or RIGHT button to select the PTZ address from 0 to 255 2 The default PTZ address is as below Channe Channel 32 6 PTZ BAUDRATE 1 Press UP or DOWN button on the front panel to move the cursor to the PTZ BAUDRATE line at the CAMERA setup menu Press LEFT or RIGHT button to select the PTZ baud rate 2 The default PTZ baud rate is 2400bps 7 MAIN ROT TIME 1 Press UP or DOWN button on the front panel to move the cursor to the MAIN ROT TIME line at the CAMERA setup menu Press LEFT or RIGHT button to set displaying duration of each channel screen in the auto sequence mode 2 When setting it to OFF the auto sequence function of this channel is disabled The default auto sequence duration is 2 seconds 8 AUDIO VOLUME 1 Press ENTER button on the front panel to enter audio volume setting mode Press LEFT or RIGHT button to decrease or increase the audio volume for the live displaying channel 2 After setting press ENTER or CANCEL button to go back to the CAMERA setup menu 9 LIVE VIDEO HIDE 1 Press UP or DOWN button on the front panel to move the cursor to the L
13. 6 Installation Process 1 Remove the power cord of DVR adaptor 2 Remove the screws of the cover and open the top cover of the DVR Screw and take out the HDD bracket and mount HDD to the bracket with the screws Mount the bracket with HDD to DVR with the screws Connect power cord and SATA cable between HDD and DVR main board Then mount the top cover of DVR with the screws 3 Connect BNC for CAMERA IN port MONITOR OUT port and JACK for AUDIO IN AUDIO OUT port from the relevant equipments 4 Connect the power cord of adaptor II OPERATION This icon on the bottom status bar is called the MENU icon in this manual This button in the menu is called the SET button in this manual This button in the menu is called the CANCEL button in this manual BEBE This button in the menu is called the OK button in this manual 2 1 Power On 1 After installation correctly connect power adaptor to switch the power of DVR on 2 The HDD must be formatted by DVR when using the HDD first time 2 2 Power Off 1 Enter the popup menu and select QUIT to power off the DVR During this time press ENTER button on the front panel to power on DVR again Note If the DVR power off abnormally during recording playback or system setup it will take longer time to power on 2 If the DVR is not in use for a long time please remove the connection of the power cord of adaptor 2 3 Display Mode 1 Press the MODE button or LE
14. DISK FORMAT 8 FIRMWARE UPGRADE 9 FACTORY RESET 10 LANGUAGE 11 SPOT MONITOR 12 VGA IV FACTORY DEFAULT V NETWORK VIEWER 5 1 IE Browser 5 2 NetViewer VI SPECIFICATION I INSTALLATION 1 1 Packing Detail 1 User s manual 1 2 DC12V 2A 4CH DC12V 3A 8CH or DC12V 5A 16 24 32CH power adaptor 1 3 Screws 1 set 4 Infrared remote controller 1 Optional for Mini 4CH DVR 5 USB port mouse 1 4 CD with mobile software and net viewer software 1 1 2 Front Panel Controls Mini 4CH DVR 4 8 CH DVR Digital Video Recorder 16 CH DVR REC BACKUP 4 SEARCH 4d aaj Mini 16 CH DVR Ee BH EE ERF ES EE e MEM o MEN MUN 24 CH DVR 32 CH DVR 6 1 1 MENU button During the live display mode press this button to display MAIN MENU and enter main setup menu press CANCEL button to exit the main setup menu After setting parameters in the menu press MENU button to save and exit menu In PTZ operation mode and CAMERA COLOR menu press this button to make the PTZ menu and CAMERA COLOR menu transparent 2 CANCEL button In the setup menu or PTZ operation mode press this button to exit the menu or PTZ operation mode 3 Number button 1 10 For 16 24 32CH DVR Press the desired camera number button you wish to display on the monitor 4 MODE button Repeat pressing this button to select the different display mode 9 SPLIT QUAD PIP FULL CHANNEL and 16 25 36
15. a PATROL number and select a PRESET number you want to delete from this tour Click on the DEL PRE button to delete selected preset position from this tour At the PTZ PRESET menu select PATROL number or other tour number you want to delete Click on the CLR PAT button to delete selected tour 4 AUX a At the PTZ PRESET menu move the cursor to the AUX frame Turn the middle button of mouse to set AUX number to 1 or other number you want to operate At the PTZ PRESET menu click on the AUX ON button to turn on this aux operation For aux operation please refer to the user manual of PTZ At the PTZ PRESET menu click on the AUX OFF button to turn off this aux operation For aux operation please refer to the user manual of PTZ 2 13 3 PTZ Other Set Function 1 In PTZ operation mode press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to SET button at the menu press ENTER button on the front panel to display PTZ SET menu and enter PTZ other function setting mode If it does not support pattern and auto scan operation for the PTZ protocol this menu can not be opened FUP LIGH CAMPOWER 2 PATTERN a At the PTZ SET menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the PATTERN frame Press UP or DOWN button on the front panel to set PATTERN number to 1 Move the cursor to the BEGIN button a
16. arrow to control tilt function Click or keep pressing the mouse left button on LEFT UP arrow LEFT DOWN arrow RIGHT UP arrow or RIGHT DOWN arrow to operate pan tilt in relevant direction 3 At the PTZ control menu click or keep pressing the mouse left button on ZOOM MINUS and ZOOM PLUS icon to control zoom near and far function Click or keep pressing the mouse left button on FOCUS MINUS and FOCUS PLUS icon to control focus near and far function Click or keep pressing the mouse left button on IRIS MINUS and IRIS PLUS icon to control iris close and open function 4 At the PTZ control menu click on AUTO PAN button to enable PTZ AUTO control function and word AUTO PAN will become yellow color Click on AUTO PAN button again to exit PTZ AUTO control function and word AUTO PAN will become white color 5 Move the cursor to SPEED frame turn the middle button of mouse to set the pan tilt speed from 1 to 8 6 At the PTZ control menu click on PRESET button to display PTZ PRESET menu and enter PTZ preset function setting 7 At the PTZ control menu click on SET button to display PTZ SET menu and enter PTZ other functions setting 8 If PTZ protocol supports position function it will display word SIT on the round icon among pan tilt arrows At the PTZ control menu click on SIT icon to operate PTZ position function 9 At the PTZ control menu click on CANCEL button or right click to ex
17. at the RECORD setup menu 2 Press REC button on the front panel or remote controller to begin manual recording Or press the ENTER button on the front panel to display POPUP MENU during the live display mode select the EMG RECORD button to begin manual recording The red recording icon will be displayed on the bottom status bar The letter E will be displayed on each channel 3 If the hard disk is full during recording the system may stop recording when setting HDD OVERWRITE to OFF at the SYSTEM INFO setup menu The system may not stop recording and automatically overwrite the oldest recorded file when setting HDD OVERWRITE to ON at the SYSTEM INFO menu 4 Press REC button again on the front panel or remote controller to stop manual recording Or press the ENTER button on the front panel to display POPUP MENU during the live display mode select the EMG RECORD button to stop manual recording 2 5 Alarm Recording Sensor and motion recording 1 Stop manual recording 2 Connect ALARM IN port of DVR from outside alarm equipments if selecting SENSOR recording mode 3 Select the channel RECORD MODE to SENSOR or MOTION at the RECORD setup menu Correctly select sensor type and duration at the SENSOR setup menu if selecting SENSOR recording mode Correctly select motion setting at the MOTION setup menu if selecting MOTION recording mode 4 In the SENSOR recording mode when a alarm input signal is detected the letter S
18. displayed as below ka CAMERA PTZ PROTOCOL PTZ ADDRESS PTZ BAUDRATE MAIN ROT TIME AUDIO VOLUME LIVE VIDEO HIDE PLAYBACK VIDEO HIDE COVER AREA 1 CHANNEL Press UP or DOWN button on the front panel to move the cursor to the CHANNEL line at the CAMERA setup menu Press LEFT RIGHT button to select the channel to set Select ALL to set all channels When selecting ALL if one item display it means that this feature item of each channel is different When saving the setting if the item selected the setting of this item is not changed 2 COLOR 1 2 Press UP or DOWN button on the front panel to move the cursor to the COLOR line at the CAMERA setup menu Press ENTER button to display the COLOR submenu press LEFT or RIGHT button to set the parameters At the COLOR submenu press UP or DOWN button on the front panel to move the cursor to CONTRAST BRIGHTNESS HUE SATURATION or SHARPNESS line and press LEFT or RIGHT button to change image contrast brightness hue saturation and turn on off the sharpness The COLOR submenu displayed as below CONTRAST BRIGHTNESS HUE SATURATION SHARPNESS Butler 3 TITLE 1 2 Press UP or DOWN button on the front panel to move the cursor to the TITLE line at the CAMERA setup menu Press ENTER button to display a keyboard box
19. motion area The selected motion area will become white color Press ENTER button again to finish motion area selecting and selected motion area will become transparent Using the same way can select the other desired motion area At the MOTION AREA setup screen press MENU button on the front panel to display the setup menu Press UP or DOWN button to move the cursor to the CLEAR line and press ENTER button to exit the menu and begin clearing motion area Press UP DOWN LEFT or RIGHT button to move the cursor to a starting position of selected motion area Press ENTER button on the front panel then press UP DOWN LEFT or RIGHT button to clear selected motion area The selected area will become white color Press ENTER button again to finish motion area clearing and the selected area will become red color At the MOTION AREA setup screen press MENU button on the front panel to display the setup menu Press UP or DOWN button to move the cursor to the EXIT line and press ENTER button to exit the MOTION AREA setup screen and return to the MOTION setup menu Mouse 1 Move the cursor to the MOTION AREA line at the MOTION setup menu Click on the SET button to display the MOTION AREA setup screen 2 At the MOTION AREA setup screen click the right mouse button to display a setup menu Move the cursor to the SELECT line and clic
20. to the DISK line and press UP or DOWN button to select HDD When using only one HDD it can not be selected DEVICE It will display USB if the USB device is connected to this DVR It will display CDROM if the SATA DVDRW ROM device connected to the DVR CHANNEL If the USB or SATA DVDRW device is connected to this DVR press LEFT or RIGHT button on the front panel to move the cursor to the CHANNEL line and press MENU button to display the CHANNEL ENABLE menu Press LEFT or RIGHT button to select the backup channel at the CHANNEL ENABLE menu and press UP DOWN button to select ON or OFF to enable or disable the backup channel Press ENTER button to return to the BACKUP setup menu START If the USB or SATA DVDRW device is connected to this DVR press LEFT or RIGHT button on the front panel to move the cursor to the date or time of START line and press UP or DOWN button to select backup beginning date time Or press MENU button to display the CALENDAR menu Press LEFT or RIGHT button to select the date at the CALENDAR menu and press ENTER button to return to the BACKUP setup menu END If the USB or SATA DVDRW device is connected to this DVR press LEFT or RIGHT button on the front panel to move the cursor to the date or time of END line and press UP or DOWN button to select backup end date time Or press MENU bu
21. will be displayed on the channel the relevant single screen will begin ALARM recording and the letter R will be displayed on the channel In the MOTION recording mode when motion detected the letter M will be displayed on the channel the DVR will begin ALARM recording and the letter R will be displayed on the channel If alarm signal cannot be detected it will keep ALARM recording for the duration set in the SENSOR or MOTION setup menu and then stop ALARM recording automatically 5 Select the channel RECORD MODE to OFF at the RECORD setup menu to disable ALARM recording 2 6 Schedule Recording 1 Stop manual recording 2 Select the channel RECORD MODE to SCHEDULE at the RECORD setup menu There are totally 5 schedule recording lists to select 3 Correctly set the schedule recording date time and type for a schedule recording list at the SCHEDULE setup menu 4 The system begins or stops schedule recording automatically according to the SCHEDULE setup 5 Select the channel RECORD MODE to OFF at the RECORD setup menu to disable SCHEDULE recording 2 7 Playback 1 Press SEARCH button on the front panel to display SEARCH MENU during the live display mode Then press LEFT or RIGHT button to select the playback modes TIME SEARCH EVENT SEARCH or URGENT SEARCH and playback date time Press ENTER button to begin playback URGENT SEARCH Pa SUN MON TUE WED THU FRI SAT 2 During the playback mo
22. 3 Display Mode 2 4 Manual Recording 2 5 Alarm Recording 2 6 Schedule Recording 2 7 Playback 2 8 Time Searching Playback 2 9 Event Searching Playback 2 10 Urgent Searching Playback 2 11 USB backup 2 12 System Information 2 13 PTZ Control 2 13 1 PTZ Operation Function 2 13 2 PTZ Preset Function 2 13 3 PTZ Other Set Function 2 13 4 PTZ Menu Matrix Function 2 14 Login SYSTEM MENU SETUP 3 1 Main Menu Setup 3 2 CAMERA Menu Setup 1 CHANNEL 2 COLOR 3 TITLE 4 PTZ PROTOCOL 5 PTZ ADDRESS 6 PTZ BAUDRATE 7 MAIN ROT TIME 8 AUDIO VOLUME 9 LIVE VIDEO HIDE 10 PLAYBACK VIDEO HIDE 11 COVER AREA 3 3 RECORD Menu Setup 1 CHANNEL 2 RESOLUTION 3 PRE RECORD 4 FPS 5 QUALITY 6 BITRATE 7 RECORD MODE 8 AUDIO 9 SCHEDULE 10 SYSTEM MAINTENANCE 3 4 MOTION Menu Setup 1 CAMERA CHANNEL 2 MOTION ENABLE 3 SENSITIVITY 4 MOTION AREA 5 POST RECORD TIME 6 BUZZER TIME 7 ALARM TIME 3 5 SENSOR Menu Setup 1 SENSOR CHANNEL 2 SENSOR TYPE 3 POST RECORD TIME 4 BUZZER TIME 5 ALARM TIME 6 HDD LOSS 7 VIDEO LOSS 8 HDD FULL 3 6 SCHEDULE Menu Setup 3 7 NETWORK Menu Setup 1 IP MODE PORT IP ADDRESS MAC ADDRESS NETMASK GATEWAY NAME SERVER DDNS EMAIL 10 BITRATE 11 MOBILE PORT 12 IE PORT M E EL CE P 3 8 BACKUP Menu Setup 1 DISK 2 DEVICE 3 CHANNEL 4 START 5 END 6 TOTAL 7 AVI 3 9 SYSTEM Menu Setup 1 TIME SETUP 2 ACCOUNT MANAGER 3 SYSTEM INFO 4 VIDEO FORMAT 5 LOG VIEW 6 LOG SET 7
23. DULE MENI WORK MENU 3 If login user is admin press UP or DOWN button on the front panel to move the cursor to ADD USER line at the ACCOUNT MANAGER menu Press ENTER button to display ADD USER menu Press UP or DOWN button to move the cursor to the USERNAME and the USER PASSWORD line and press ENTER button to open keyboard box to set a user name and the password for this new user Press UP or DOWN button on the front panel to move the cursor to the other selectable items of authority list at the ADD USER menu Press ENTER button to select or unselect the relevant authority item for the new user When the item is selected and ticked the user is allowed to operate this function Press MENU button on the front panel to save the setting and return back to previous menu USER AUTHORITY LIVE MONTTOF PLAYBACK EMERGENCY RECORD PTZ CONTRO CAMERA MEN RECORD MEN N MEN SENSOR MENU SCHEDULE MEN WORK MENI 4 If login user is admin press UP or DOWN button on the front panel to move the cursor to a normal user line at the ACCOUNT MANAGER menu Press MENU button to delete the normal user and display a WARNNING box Press ENTER button to delete the user 5 If login user is not admin using the same way to change itself password and authority at the MODIFY USER menu Mouse 1 2 3 4 If login user is admin move the cursor to a
24. DVR 4 8 16 24 32CH Stand alone digital video recorder User Manual 4 8 16 24 32 CHANNEL H 264 DVR WARNING e To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture e All the safety and operating instructions must be read before the unit is operated PRECAUTION e Make sure to switch the power off before you install the DVR e Avoid using the DVR outside of the reference temperature and humidity indicated in the specification e Avoid exposing the DVR to violent movement or vibration e Do not use or store the DVR in direct sunlight or near to any source of heat e Do not place any object into the holes used for air circulation e Always use the DVR in the well ventilated location to prevent overheating e Do not disassemble or reassemble the product It may cause malfunction or fire e There is the danger of an electric shock if DVR is repaired by an unqualified service engineer or installer POWER SUPPLY e Please use the provided adaptor The DVR provide DCI2V 2A 4CH 3A 8CH 5A 16 24 32CH power adaptor Please select the correct voltage and power if using other adaptor e Keep the adaptor and power cord dry and protect from humidity When this machine is not using for a long time please remove the connection of power adaptor FEATURES Non pc stand alone security digital video recorder with embedded operation system H 264 compression format Mobile monitoring Multi la
25. EARCH and playback date time Press ENTER button to begin playback Press CANCEL button to stop playback In PTZ operation mode press this button to control pan right For Mini 4CH DVR in the playback mode press this button to turn on or off the playback audio In SCHEDULE setup mode press this button to select different recording mode 11 MA REWIND button During the playback mode repeat pressing this button to speed up playback backward at the speed of 2x 4x or 6x In PTZ operation mode press this button to control tilt up 12 P PLAY PAUSE button During the playback mode press this button to display a still picture To restart playback press this button again In PTZ operation mode press this button to control tilt down 13 PP FAST FORWARD button During the playback mode repeat pressing this button to speed up playback forward at the speed of 2x 4x or 6x 14 JOG amp SHUTTLE For 16 32CH DVR During the playback mode turn the SHUTTLE ring to the right and left to select speed of FAST FORWARD and REWIND Turn the JOG dial in either direction continuously for playback of consecutive frames 2 15 A ENTER button During the live display mode press this button to display the popup menu In the setup menu press this button to enter the next operation In PTZ operation mode press this button to enter PTZ operation During the power off status by popup menu
26. ENU icon on the bottom status bar to display POPUP MENU during the live display mode Then click on the SETUP button to display MAIN MENU Then click on the BACKUP button to enter BACKUP setup menu 2 At the BACKUP setup menu move the cursor to the CHANNEL START or END line Click on the SET button to select the backup channel backup beginning date time and end date time or turn the middle button of mouse to select backup beginning date time and end date time 3 Click on the top right O OK button to begin backup 2 12 System Information FIRMWARE VER HDD HDD 2 HDD 3 HDD 4 HDD OVERWRITE 1 Press MENU button on the front panel to display MAIN MENU during the live display mode 2 In the MAIN MENU Press UP DOWN LEFT and RIGHT buttons to select SYSTEM button and press ENTER button to enter SYSTEM setup menu 3 Press UP or DOWN button on the front panel to move the cursor to the SYSTEM INFO line Press ENTER button on the front panel to enter SYSTEM INFO menu 4 Press LEFT and RIGHT buttons to enable or disable HDD overwrite function When setting HDD OVERWRITE to OFF the system may stop recording if the hard disk is full during recording When setting OVERWRITE to ON the system may not stop recording and automatically overwrite the oldest recorded file Mouse 1 Click the mouse on the MENU icon on the bottom status
27. FT and RIGHT button to select the different screen display FULL CHANNEL PIP QUAD 9 SPLIT 16 25 36 SPLIT during the live display mode Press NUMBER button or A UP and W DOWN button to select single camera and the single live view is displaying on the screen Mouse Click the mouse on the MENU icon on the bottom status bar to display POPUP MENU during the live display mode click on the LIVE button and select the different screen display mode In the live QUAD or SPLIT display mode double click the image of a channel to display the single channel Double click the image again to display QUAD or SPLIT image 2 Press the AUTO button on the front panel to start auto sequence display Each screen displaying will automatically switch according to the MAIN ROT TIME duration setting in the setup menu 3 To zoom in images can only be operated by mouse Mouse Select the desired single camera and the single live view is displaying on the screen Click the mouse on the MENU icon on the bottom status bar to display POPUP MENU during the live display mode click on the Zoom button to enable ZOOM function Keep pressing the left mouse button and drag it to select zoom area After release the left mouse button it will zoom in the selected image Right click the mouse to return back the normal image Double click the mouse to exit ZOOM function 2 4 Manual Recording 1 Select the channel RECORD MODE to OFF
28. IME line When set CHANNEL MODE to the display mode except HEXA the ROTATION TIME can be set from 1 second to 10 seconds When set it to OFF it is unchangeable display and no channel rotation for spot monitor 3 Press ENTER button on the front panel to return back to SYSTEM setup menu 12 VGA Press UP or DOWN button on the front panel to move the cursor to the VGA line and press LEFT RIGHT button to select VGA display mode 800x600 1024x768 or 1280x1024 IV FACTORY DEFAULT The factory default setting for the DVR displayed as below Factory SYSTEM User Name l n Login Setting in menu SET P No password Playback video OFF ON OFF hide Low standard high highest A Low standard high Record Bit rate Highest i highest Record Parameter Alarm Post Time 10 60 second OFF Schedule Record Always Motion Sensor Always Mode OFF Always Always Motion Sensor Record Mode Record Schedule Off PTZ Protocol PELCO D Optional Tero 99 Topon Record Quality Highest Motion Alarm 5 second 1 60 second OFF Alarm 1 60 second OFF V Network Viewer 5 1 IE Browser Enter IE browser of your computer input the IP address of the DVR or DDNS name of DVR include IE port number no need to input the default IE port 80 If it is first time to use computer to connect with DVR it will ask to download software plug in and it will take several seconds to download If it suc
29. IVE VIDEO HIDE line at the CAMERA setup menu Press LEFT or RIGHT button to turn on or off the hide function for live video 2 When setting it to ON no video displayed in this channel and it is black screen for the live view of this channel 10 PLAYBACK VIDEO HIDE 1 Press UP or DOWN button on the front panel to move the cursor to the PLAYBACK VIDEO HIDE line at the CAMERA setup menu Press LEFT or RIGHT button to turn on or off the hide function for playback video 2 When setting it to ON no video displayed in this channel and it is black screen for the playback of this channel 11 COVER AREA 1 Press ENTER button on the front panel to enter cover area setting menu There are totally 3 areas marked with different colors to set Press UP or DOWN button to SELECT AREA 1 line and press ENTER button to start setting 2 Press UP DOWN LEFT or RIGHT button on the front panel to move the cursor to the start point of area press ENTER button to confirm Then press UP DOWN LEFT or RIGHT button to move the cursor to get the area marked with relevant color Press ENTER button again to finish area setting Press Menu button on the front panel to enter cover area setting menu Press UP or DOWN button to select PREVIEW to view the selected area Using the same way to set the cover area 2 and cover area 3 The area tha
30. Press UP DOWN LEFT or RIGHT button on the front panel to move cursor to select a number or letter on the keyboard box then press ENTER button on the front panel to input this number or letter Select on the keyboard box to clear the previous display 3 After input the desired camera title move the cursor to ENTER on the keyboard box press ENTER button on the front panel to set the camera title CHOT_ E Mouse 1 Click the mouse on the MENU icon on the bottom status bar to display POPUP MENU during the live display mode Then click on the SETUP button to display MAIN MENU Click on the CAMERA button to enter CAMERA setup menu 2 At the CAMERA setup menu move the cursor to the TITLE line Click on the SET button to display a keyboard box 3 Click on a number or letter on the keyboard box to input it Click on on the keyboard box to clear the previous display After input the desired camera title click on ENTER on the keyboard box to set the camera title 4 Click on the SAVE button at the CAMERA setup menu to save the setting Then exit the submenu and main menu Click on CANCEL button to exit submenu without saving 4 PTZ PROTOCOL 1 Press UP or DOWN button on the front panel to move the cursor to the PTZ PROTOCOL line at the CAMERA setup menu Press LEFT or RIGHT button to select the PTZ protocol
31. SPLIT 5 AUTO button In the live display mode press this button to begin auto sequence mode Each screen displaying will be automatically switching according to the MAIN ROT TIME SETUP In PTZ operation mode press this button to enter PTZ auto pan function press this button again to exit PTZ auto pan function 6 MUTE button During the live display mode press this button to turn on and turn off the audio 7 BACKUP button During the live display mode press this button to backup the recorded data if the USB device is connected to this DVR Then select the beginning backup time and end backup time and press ENTER button to begin backup If there is no USB device connected to DVR it will display BACKUP DEVICE IS NOT FOUND 8 PTZ button In the single screen mode press this button to enter PTZ operation mode to control pan tilt focus iris zoom and other functions Press CANCEL button to exit PTZ operation mode 9 REC button When setting DVR RECORD MODE to OFF in the menu press this button to begin manual urgent recording The red recording icon will be displayed on the bottom status bar Press this button again to stop recording In PTZ operation mode press this button to control pan left 10 SEARCH button During the live display mode press this button to enter SEARCH menu Then press LEFT or RIGHT button to select the playback modes TIME SEARCH EVENT SEARCH and URGENT S
32. TION For Mini 4CH DVR press SEARCH button on the front panel to select the MOTION button at the SCHEDULE setup menu The schedule recording mode is set to MOTION 3 Press NUMBER 3 or MUTE button on the front panel to select the SENSOR button at the SCHEDULE setup menu Or press UP DOWN LEFT or RIGHT button on the front panel to select the SENSOR button at the SCHEDULE setup menu The schedule recording mode is set to SENSOR For Mini 4CH DVR press SEARCH button on the front panel to select the SENSOR button at the SCHEDULE setup menu The schedule recording 3 7 mode is set to SENSOR 4 Press NUMBER 4 or BACKUP button on the front panel to select the CANCEL button at the SCHEDULE setup menu Or press UP DOWN LEFT or RIGHT button on the front panel to select the CANCEL button at the SCHEDULE setup menu The schedule recording mode is set to OFF For Mini 4CH DVR press SEARCH button on the front panel to select the CANCEL button at the SCHEDULE setup menu The schedule recording mode is set to OFF 5 Press UP DOWN LEFT or RIGHT button to move the cursor to the desired day from Monday to Sunday and time from 0 to 24 Press MENU button to set the day and time to the selected schedule recording mode 6 At the SCHEDULE setup menu press UP or DOWN button on the front panel to move the cursor to the SCHEDULE LIST then pre
33. TZ PRESET menu move the cursor to the PRESET frame Turn the middle button of mouse to set PRESET number to 1 Click on the SAVE PRE button to save current PTZ position to 1 Click on CANCEL button or right click to exit PTZ preset function and return to PTZ operation mode Click on the direction arrows and zoom focus iris icons to control PTZ to a desired position Enter PTZ PRESET menu again and set PRESET number to 2 Click on the SAVE PRE button to save current PTZ position to 2 Using the same way to save other PTZ preset positions At the PTZ PRESET menu select PRESET number to 1 or other PTZ position number you wish to load Click on the LOAD PRE button to move PTZ to selected preset position At the PTZ PRESET menu select PRESET number to 1 or other PTZ position number you wish to delete Click on the CLR PRE button to delete preset position 3 TOUR a At the PTZ PRESET menu move the cursor to the PATROL frame Turn the middle button of mouse to set PATROL number to 1 Select PRESET number to 1 or other number you want to add to this tour Click on the ADD PRE button to add this preset position to tour 1 Using the same way to add other preset position to tour 1 Using the same way to set other tour At the PTZ PRESET menu select PATROL number to 1 click on the TOUR button to start tour 1 Click on the TOUR button again to stop tour 1 Using the same way to start and stop other tours At the PTZ PRESET menu select
34. admin user press ENTER button to display the MODIFY USER menu The ACCOUNT MANAGER menu displayed as below 1 2 ACCOUNT MANAGER USERNAME There are 3 factory setting users The user name admin is an administrator user and the factory setting password is admin The user name user is a default user the factory setting password is user and its authority is that only view live video The user name 1 is a normal user and factory setting is no password with all authority The administrator user and default user can not be deleted The normal user can be deleted or added by administrator user Only administrator user can add or delete normal user and change the authority of other users If login user is admin press UP or DOWN button on the front panel to move the cursor to any user line at the ACCOUNT MANAGER menu Press ENTER button to display MODIFY USER menu Press UP or DOWN button to move the cursor to the USER PASSWORD and press ENTER button to open keyboard box to modify the password Press UP or DOWN button on the front panel to move the cursor to the other selectable item of authority list at the MODIFY USER menu Press ENTER button to select or unselect the relevant authority item for the user Press MENU button on the front panel to save the setting and return back to previous menu f MODIFY USER NAME gt MENT ION MENT SOR MEN SCHE
35. bar to display POPUP 2 13 MENU during the live display mode Then click on the SETUP button to display MAIN MENU Then click on the SYSTEM button to enter SYSTEM setup menu At the SYSTEM setup menu move the cursor to the SYSTEM INFO line Click on the SET button to enter SYSTEM INFO menu PTZ Control zoom gt Focus a ms 2 13 1 PTZ Operation Function 1 Press the desired camera NUMBER button to select the single channel you wish to display on the monitor or press LEFT RIGHT UP DOWN buttons to view one channel video during the live display mode Then press PTZ button on the front panel to display PTZ control menu and enter the PTZ operation mode For Mini 4CH DVR press UP button or DOWN button to select the single channel you wish to display on the monitor during the live display mode Then press the ENTER button on the front panel to display POPUP MENU and select the PTZ line then press ENTER button or press PTZ button on the remote controller to display PTZ control menu and enter the PTZ operation mode Press LEFT RIGHT UP or DOWN button to move the cursor to LEFT or RIGHT arrow press ENTER button to control pan function Press LEFT RIGHT UP or DOWN button to move the cursor to UP or DOWN arrow press ENTER button to control tilt function Press LEFT
36. ceeds you will enter the USER LOGIN website The connecting method is the same with the Network Viewer as below If using free DDNS supplied by DVR open the IE browser and enter website http dy vip620 com or enter http dy vip620 com your username to access the DVR directly When using the free DDNS no need to input the port number ae a aa EAE EN BEEJ SAE 3800 WIBI SP TATI Hi d irem cea com Qa O sj i ger C sn grams Om B Sar pms kam ama Gama i t p 192 168 1 194 dasa kj aa sre E Ose Gem SIA ARATE mp 17588 o Pen DAHANA GIO Bore ug imm 5 2 NetViewer 5 2 1 Operation 1 Copy and save the network viewer software Net Viewer from CD to your PC 2 Double click Net Viewer software it will display as below Double click the area to display the single channel image Video display area l Double click again to display last display mode m Display and change PC audio volume r Select the playback mode m 1 Select the local file play mode PTZ control for pan and tilt Middle button is AUTO control for PTZ PTZ zoom control PTZ focus control katotonnec On when enable auto connection Rec On when DVR is recording avi On when NetViewer enable the AVI record assi On when recording and saving in the PC local directory On when the DVR motion alarm or sensor alarm occur Display mode Full Quad 8 split 9 split 13 split and 16 25 32 split Recording and sa
37. de press PLAY PAUSE button to pause the images Press PLAY PAUSE button again to restart playback For Mini 4CH DVR press LEFT or RIGHT button to select PLAY PAUSE mode and Pp button on the playback status bar is selected Press ENTER button to pause the images Press ENTER button again to restart playback 3 During the playback mode press 4 44 button or PP button to speed up playback backward or forward at the speed of 2x 4x or 6x For Mini 4CH DVR press LEFT or RIGHT button to select BACKWARD FORWARD mode and 40 button or pp button on the playback status bar are selected Press ENTER button to speed up playback backward or forward at the speed of 2x 4x or 6x 4 During the playback mode press 49 RIGHT button to enter step forward playback press PLAY PAUSE button to return to normal playback For Mini 4CH DVR press RIGHT button to select STEP FORWARD mode and P button on the playback status bar are selected Press ENTER button to enter step forward playback 5 During the playback mode press MODE button to select the different display mode press NUMBER button or A button or V button to select a single camera displaying on the screen For Mini 4CH DVR press UP button or DOWN button to select the different display mode or select a single camera displaying on the screen 6 Du
38. e beep does not sound 3 6 SCHEDULE Menu Setup Press MENU button on the front panel to display MAIN MENU during the live display mode Press UP DOWN LEFT and RIGHT buttons to select SCHEDULE button in the MAIN MENU and press ENTER button to enter SCHEDULE setup menu After setting press ENTER button to save the setting Then exit the submenu Press CANCEL button to exit submenu without saving The last line is the comment for recoding mode when selecting ALWAYS MOTION SENSOR or CANCEL recording mode The SCHEDULE setup menu displayed as below Lund X 3 SCHEDULE 1 0 2 4 6 18 10 ARSA 46 gt 181 20 22 24 2 MOTION SENSOR CANCEL ALWAYS RECORD 1 Press NUMBER 1 or MODE button on the front panel to select the ALWAYS button at the SCHEDULE setup menu Or press UP DOWN LEFT or RIGHT button on the front panel to select the ALWAYS button at the SCHEDULE setup menu The schedule recording mode is set to ALWAYS For Mini 4CH DVR press SEARCH button on the front panel to select the ALWAYS button at the SCHEDULE setup menu The schedule recording mode is set to ALWAYS 2 Press NUMBER 2 or AUTO button on the front panel to select the MOTION button at the SCHEDULE setup menu Or press UP DOWN LEFT or RIGHT button on the front panel to select the MOTION button at the SCHEDULE setup menu The schedule recording mode is set to MO
39. e front panel to display SEARCH MENU during the live display mode 2 Press LEFT or RIGHT button to select EVENT SEARCH playback mode and press ENTER button to enter EVENT SEARCH menu 3 Press UP DOWN LEFT and RIGHT buttons to select the event beginning date time for playback 4 Press ENTER button to begin EVENT SEACHING playback The playback is only for motion sensor and schedule recording mode Mouse 1 Click the mouse on the MENU icon on the bottom status bar to display POPUP MENU during the live display mode Then click on the SEARCH button to display SEARCH MENU Click on the EVENT SEARCH button to enter EVENT SEARCH menu 2 At the EVENT SEARCH menu move the cursor or turn the middle button of mouse to select the event beginning date time for playback 3 Then click on the top right O OK button to begin EVENT SEACHING playback or double click the event beginning date time to begin EVENT SEACHING playback 2 10 Urgent Searching Playback EMERGENCY SEARCH Le RECORD TIME Q cid J o C 1 Press SEARCH button on the front panel to display SEARCH MENU during the live display mode 2 Press LEFT or RIGHT button to select URGENT SEARCH playback mode and press ENTER button to enter EMERGENCY SEARCH menu 3 Press UP DOWN LEFT and RIGHT buttons to select the emergency recording date time for playback 4 Press ENTER butto
40. enu SYSTEM INFO Press UP or DOWN button on the front panel to move the cursor to the SYSTEM INFO line and press ENTER button to display the SYSTEM INFO menu The SYSTEM INFO menu displayed as below FIRMWARE VER HDD HDD 2 HDD 3 HDD 4 HDD OVERWRITE 1 2 3 T It will display the system information include system firmware version HDD information OVERWRITE Press LEFT RIGHT button at the SYSTEM INFO menu to select overwrite function ON or OFF Press ENTER button on the front panel to exit the SYSTEM INFO menu and return to the SYSTEM setup menu VIDEO FORMAT Press UP or DOWN button on the front panel to move the cursor to the VIDEO FORMAT line and press LEFT RIGHT button to set system to PAL or NTSC LOG VIEW Press UP or DOWN button on the front panel to move the cursor to the LOG VIEW line and press ENTER button to display the SYSTEM LOG menu Press UP or DOWN button at the SYSTEM LOG menu to display the information of event log Press CANCEL button on the front panel to exit the SYSTEM LOG menu and return to the SYSTEM setup menu LOG SET Press UP or DOWN button on the front panel to move the cursor to the LOG SET line and press ENTER button to display the LOG SET menu Press UP or DOWN button at the LOG SET menu to move the cursor to MOTION SENSOR MANUAL or BOOTING
41. ete from this tour Press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the DEL PRE button Press ENTER button to delete selected preset position from this tour At the PTZ PRESET menu select PATROL number or other tour number you want to delete Press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the CLR PAT button Press ENTER button to delete selected tour 4 AUX a At the PTZ PRESET menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the AUX frame Press UP or DOWN button on the front panel to set AUX number to 1 or other number you want to operate At the PTZ PRESET menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the AUX ON button Press ENTER button on the front panel to turn on this aux operation For aux operation please refer to the user manual of PTZ At the PTZ PRESET menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the AUX OFF button Press ENTER button on the front panel to turn off this aux operation For aux operation please refer to the user manual of PTZ Mouse 1 In PTZ operation mode click on the PRESET button at the menu to display PTZ PRESET menu and enter PTZ preset function setting mode 2 PRESET a At the P
42. fault server IP address Press UP or DOWN button to NTP ON and press LEFT or RIGHT button to set it to ON Press ENTER button to get correct date and time for DVR When using NTP to set date and time make sure the DVR can be connected to internet The TIME SET menu displayed as below odd ME SETIP asana re masaalah Bad TIME FORMAT ZONE SERVER NTP ON Mouse 1 2 3 4 Move the cursor to the TIME SET line at the SYSTEM setup menu Click on the SET button to display the TIME SET menu Move the cursor to the date time of TIME line or FORMAT line Turn the middle mouse button to set the current date time and select display format of date time at the TIME SET menu Click on the top right O OK button at the TIME SET menu to return to the SYSTEM setup menu Move the cursor to ZONE Turn the middle mouse button to select your local area zone Move the cursor to SERVER and click on the SET button to set a time server IP address or keep the default server IP address Move the cursor to NTP ON and click on the SET button to set correct date and time for DVR When using NTP to set date and time make sure the DVR can be connected to internet ACCOUNT MANAGER If login user is admin press UP or DOWN button on the front panel to move the cursor to the ACCOUNT MANAGER line and press ENTER button to display the ACCOUNT MANAGER menu For other users except
43. g the same way to save other PTZ operating route to relevant pattern number c Atthe PTZ SET menu select PATTERN number to 1 or other PATTERN number you wish to run Click on the PATTERN button to start pattern 1 route operation Click on the PATTERN button again to stop pattern 1 route operation Using the same way to run other pattern operation 3 AUTO SCAN a At the PTZ SET menu click on CANCEL button or right click to exit PTZ other function setting mode and return to PTZ operation mode Click on the direction arrows and zoom focus iris icons to control PTZ to a position as the left position b Enter the PTZ SET menu again click on the LEFT button to set the PTZ position to the left position c At the PTZ SET menu click on CANCEL button or right click to exit PTZ other function setting mode and return to PTZ operation mode Click on the direction arrows and zoom focus iris icons to control PTZ to a position as the right position Enter the PTZ SET menu again click on the RIGHT button to set the PTZ position to the right position d Atthe PTZ SET menu click on the AUTOSCAN button to start PTZ auto scan between the left position and the right position Click on the AUTOSCAN button again to stop PTZ auto scan 4 Others a Atthe PTZ SET menu click on the FLIP button to flip the PTZ b At the PTZ SET menu click on the RESET button to reset the PTZ c At the PTZ SET menu click on the LIGHT button to turn on the light Clic
44. gain on the front panel to disable PTZ menu setting At the MENU MATRIX setup menu if PTZ menu function is enabled press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the MENU UP M DOWN M LEFT or M RIGHT button Press ENTER button on the front panel to move the cursor to up down left or right direction at the PTZ menu At the MENU MATRIX setup menu if PTZ menu function is enabled press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the M ENTER button Press ENTER button on the front panel to enter PTZ sub menu Press ENTER button again to exit PTZ sub menu 4 Others a At the MENU MATRIX setup menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the ALARM button Press ENTER button on the front panel to start alarm search At the MENU MATRIX setup menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the RESET button Press ENTER button on the front panel to reset the PTZ At the MENU MATRIX setup menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the LIGHT button Press ENTER button on the front panel to turn on the light Press ENTER button again on the front panel to turn off the light At the MENU MATRIX setup menu press LEFT
45. gle camera and the single channel is displaying on the screen Click on the Zoom button to enable ZOOM function Keep pressing the left mouse button and drag it to select zoom area After release the left mouse button it will zoom in the selected image Right click the mouse to return back the normal image Double click the mouse to exit ZOOM function 2 8 Time Searching Playback 1 2 3 4 an n Q sTIMESSEARCH x32 XD Press SEARCH button on the front panel to display SEARCH MENU during the live display mode Press LEFT or RIGHT button to select TIME SEARCH playback mode and press ENTER button to enter TIME SEARCH menu Press UP DOWN LEFT and RIGHT buttons to select the beginning date time for playback Press ENTER button to begin TIME SEACHING playback Mouse Click the mouse on the MENU icon on the bottom status bar to display POPUP MENU during the live display mode Then click on the SEARCH button to display SEARCH MENU Click on the TIME SEARCH button to enter TIME SEARCH menu or double click the date time to begin TIME SEACHING playback At the TIME SEARCH menu move the mouse and turn the middle button of mouse to select the beginning date time for playback Then click on the top right O OK button to begin TIME SEACHING playback 2 9 Event Searching Playback EVENT INFO mom omm G oM b M IL V 1 Press SEARCH button on th
46. ing IP address to set NAME SERVER DDNS Press UP or DOWN button on the front panel to move the cursor to the DDNS line at the NETWORK setup menu Press ENTER button to display the DDNS setup menu The DDNS setup menu displayed as below 1 2 3 SERVER HOSTNAME USERNAME PASSWORD UPNP Press UP or DOWN button on the front panel to move the cursor to the SERVER line at the DDNS setup menu Press LEFT RIGHT button to select DYNDNS 3322 perfect or myq see When selecting OFF the DDNS server is disabled When not setting DDNS server to OFF press UP or DOWN button on the front panel to move the cursor to the HOSTNAME USERNAME or PASSWORD line at the DDNS setup menu Press MENU button to display a keyboard box Using the same way for setting IP address to set them When setting DDNS to dvr ddns it can apply for a free DDNS If apply for free DDNS first time press UP or DOWN button on the front panel or use the mouse to move the cursor to the DDNS and press LEFT or RIGHT button to set it to ON then press ENTER button or click the SET 4 button beside DDNS It will apply for free DDNS automatically After some time the DVR will get a user name and it can not be changed You can open the IE browser and enter host name website http dy vip620 com or enter http dy vip620 com your username to access the DVR directly When apply f
47. ious number After input the correct password and move the cursor to ENTER button on the keyboard box press ENTER button on the front panel to return back to LOGIN MENU 3 After input correct user name and password at the LOGIN MENU press ENTER button on the front panel to login Mouse 1 Move the cursor to USER NAME line Click on the SET button to display a 66a 99 keyboard box Click on a letter number or symbol to input it Click on on the keyboard box to clear the previous input After input the correct user name click on ENTER button on the keyboard box to return back to LOGIN MENU 2 Move the cursor to PASSWORD line Click on the SET button to display a keyboard box Click on a number to input it Select lt on the keyboard box to clear the previous number After input the correct password click on ENTER button on the keyboard box to return back to LOGIN MENU 3 After input correct user name and password at the LOGIN MENU click on 0 OK button to login Ul SYSTEM MENU SETUP 3 1 Main Menu Setup 1 Press MENU button on the front panel to display MAIN MENU during the live display mode 2 In the MAIN MENU Press UP DOWN LEFT and RIGHT buttons to select submenu button and press ENTER button to enter relevant submenu 3 In the MAIN MENU Press CANCEL button to exit the MAIN MENU The MAIN MENU displayed as below CAMERA Mou
48. it the PTZ operation mode 10 At the PTZ control menu Move the cursor to any place of menu except SPEED frame and turn the middle button of mouse to make the PTZ menu transparent 2 13 2 PTZ Preset Function 1 In PTZ operation mode press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the PRESET button at the menu press ENTER button on the front panel to display PTZ PRESET menu and enter PTZ preset function setting mode PTZ PRESET AH PRESET 1 LOAD PRE SAVE PRE CLR PRE PATROL 1 TOUR ADO PRE DEL PRE CLR PATR AUX ON AUX OFF 2 PRESET At the PTZ PRESET menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the PRESET frame Press UP or DOWN button on the front panel to set PRESET number to 1 Move the cursor to the SAVE PRE button and press ENTER button on the front panel to save current PTZ position to 1 Press CANCEL button on the front panel to exit PTZ preset function and return to PTZ operation mode Press UP DOWN LEFT RIGHT and ENTER buttons to control PTZ to a desired position Enter PTZ PRESET menu again and set PRESET number to 2 Move the cursor to the SAVE PRE button and press ENTER button on the front panel to save current PTZ position to 2 Using the same way to save other PTZ preset positions At the PTZ PRESET menu select PRESET nu
49. k on it to exit the menu and begin setting motion area 3 Move the cursor to a starting position of motion area Keep pressing the left mouse button and drag it to select desired motion area The selected motion area will become white color Release the left mouse button to finish motion area selecting and selected motion area will become transparent 4 Using the same way can select the other desired motion area 5 At the MOTION AREA setup screen click the right mouse button to display the setup menu Move the cursor to the CLEAR line and click on it to exit the menu and begin clearing motion area 6 Move the cursor to a starting position of selected motion area Keep pressing the left mouse button and drag it to clear selected motion area The selected area will become white color Release the left mouse button to finish motion area clearing and the selected area will become red color 7 At the MOTION AREA setup screen click the right mouse button to display the setup menu Move the cursor to the EXIT line and click on it to exit the MOTION AREA setup screen and return to the MOTION setup menu 5 POST RECORD TIME 1 Press UP or DOWN button on the front panel to move the cursor to the POST RECORD TIME line at the MOTION setup menu Press LEFT or RIGHT button to select post alarm recording time 2 The post alarm recording time can be set from 10 second to 60 second When setting it to OFF the post alar
50. k on the LIGHT button again to turn off the light d Atthe PTZ SET menu click on the WIPER button to start using wiper Click on the WIPER button again to stop using wiper At the PTZ SET menu click on the CAMPOWER button to turn on the camera power Click on the CAMPOWER button again to turn off the camera power If it supports menu or matrix operation for the PTZ protocol this button is MENU button for PTZ and click on it to enter PTZ MENU MATRIX setup menu 2 13 4 PTZ Menu Matrix Function 1 At the PTZ SET menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the MENU button press ENTER button on the front panel to display PTZ MENU MATRIX setup menu and enter PTZ menu setting mode If it does not support menu and matrix operation for the PTZ protocol this menu can not be opened RESET MATRIX 2 At the MENU MATRIX setup menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the MONITOR frame Press UP or DOWN button on the front panel to set MONITOR address to 1 or other number It is only used for matrix operation if it supports PTZ matrix protocol 3 MENU a At the MENU MATRIX setup menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the MENU button Press ENTER button on the front panel to enable PTZ menu setting Press ENTER button a
51. k on the RESET button to reset the PTZ c At the MENU MATRIX setup menu click on the LIGHT button to turn on the light Click on the LIGHT button again to turn off the light d At the MENU MATRIX setup menu click on the MATRIX button to switch matrix e At the MENU MATRIX setup menu click on the CAMPOWER button to turn on the camera power Click on the CAMPOWER button again to turn off the camera power 2 14 Login 1 Press UP or DOWN button on the front panel to move the cursor to USER NAME line Press MENU button on the front panel to display a keyboard box press UP DOWN LEFT or RIGHT button on the front panel to move cursor to a letter number or symbol then press ENTER button on the front panel to input it Select lt on the keyboard box to clear the previous input After input the correct user name move the cursor to ENTER button on the keyboard box press ENTER button on the front panel to return back to LOGIN MENU 2 Press UP or DOWN button on the front panel to move the cursor to PASSWORD line Press NUMBER buttons to input correct password or press MENU button on the front panel to display a keyboard box press UP DOWN LEFT or RIGHT button on the front panel to move cursor to a number then press ENTER button on the front panel to input this number Select lt on the keyboard box to clear the prev
52. line and press LEFT or RIGHT button to turn on or off the log function of each item Press ENTER or CANCEL button on the front panel to exit the SYSTEM LOG menu and return to the SYSTEM setup menu If setting the item to ON it will display the relevant information in LOG VIEW DISK FORMAT 1 Press UP or DOWN button on the front panel to move the cursor to the DISK FORMAT line at the SYSTEM setup menu Press ENTER button to display the SELECT DISK setup menu The SELECT DISK setup menu displayed as below SELECT DISK DISK FIRST REC TIME LAST REC TIME 2 At the SELECT DISK setup menu Press LEFT or RIGHT button on the front panel to select the HDD for formatting When select ALL will format all HDD 3 Press ENTER button on the front panel to begin HDD formatting 8 FIRMWARE UPGRADE Connect the USB or SATA DVDRW device with the latest firmware Press UP or DOWN button on the front panel to move the cursor to the FIRMWARE UPGRADE line and press ENTER button to display the WARNING box The WARNING box as below FIRMWARE UPGRADE MAY MAKE THE SYSTEM FATAL ERROR CONTINUE eo 1 Press ENTER button on the front panel to begin firmware updating 2 It will take some time to update firmware After firmware updating completely the DVR will be switched off and restarted again automatically 9 FACTORY RESET Press UP or
53. m recording time is 0 second 6 BUZZER TIME 1 Press UP or DOWN button on the front panel to move the cursor to the BUZZER TIME line at the MOTION setup menu Press LEFT or RIGHT button to select beep sound time 2 The beep sound time can be set from 1 second to 60 second When setting it to OFF the beep does not sound 7 ALARM TIME 1 Press UP or DOWN button on the front panel to move the cursor to the ALARM TIME line at the MOTION setup menu Press LEFT or RIGHT button to select post output alarm time 2 The post alarm time can be set from 1 second to 60 second When setting it to OFF the alarm does not output 3 5 SENSOR Menu Setup Press MENU button on the front panel to display MAIN MENU during the live display mode Press UP DOWN LEFT and RIGHT buttons to select SENSOR button in the MAIN MENU and press ENTER button to enter SENSOR setup menu After setting press MENU button to save the setting Then exit the submenu and main menu Press CANCEL button to exit submenu without saving The SENSOR setup menu displayed as below a SENSOR ISENSOR CHANNEL ALL SENSOR TYPE NORMAL OPEN POST RECORD TIME 10 SEC BUZZER TIME OFF ALARM TIME OFF HDD LOSS 2 SEC VIDEO LOSS 2 SEC HDD FULL 2 SEC A2 4234523253234 V vvvyyyY SAVE EAI 1 SENSOR CHANNEL Press UP or DOWN button on the front panel to move the cursor
54. mber to 1 or other PTZ position number you wish to load Press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the LOAD PRE button Press ENTER button to move PTZ to selected preset position At the PTZ PRESET menu select PRESET number to 1 or other PTZ position number you wish to delete Press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the CLR PRE button Press ENTER button to delete preset position 3 TOUR a At the PTZ PRESET menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the PATROL frame Press UP or DOWN button on the front panel to set PATROL number to 1 Select PRESET number to 1 or other number you want to add to this tour Move the cursor to the ADD PRE button and press ENTER button on the front panel to add this preset position to tour 1 Using the same way to add other preset position to tour 1 Using the same way to set other tour At the PTZ PRESET menu select PATROL number to 1 press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the TOUR button Press ENTER button on the front panel to start tour 1 Press ENTER button on the front panel again to stop tour 1 Using the same way to start and stop other tours At the PTZ PRESET menu select a PATROL number and select a PRESET number you want to del
55. n to begin URGENT SEACHING playback The playback is only for manual recording mode Mouse 1 Click the mouse on the MENU icon on the bottom status bar to display POPUP MENU during the live display mode Then click on the SEARCH button to display SEARCH MENU Click on the URGENT SEARCH button to enter EMERGENCY SEARCH menu 2 At the EMERGENCY SEARCH menu move the cursor or turn the middle button of mouse to select the emergency recording date time for playback 3 Then click on the top right O OK button to begin URGENT SEACHING playback or double click the emergency recording date time to begin URGENT SEACHING playback 2 11 USB Backup 1 Connect the USB backup device to DVR USB port 2 Press MENU button on the front panel to display MAIN MENU then select BACKUP button and press ENTER button or press BACKUP button on the front panel or remote controller to display BACKUP setup menu during the live display mode The DEVICE name is USB at the BACKUP setup menu if using USB disk 3 Press LEFT or RIGHT button on the front panel to move the cursor to the CHANNEL START or END line Press MENU button on the front panel to select the backup channel backup beginning date time and end date time or press UP or DOWN button to select backup beginning date time and end date time 4 Press ENTER button on the front panel to begin backup Mouse 1 Click the mouse on the M
56. nd press ENTER button on the front panel to start pattern setting Press CANCEL button on the front panel to exit PTZ other function setting mode and return to PTZ operation mode Press UP DOWN LEFT RIGHT and ENTER buttons to control PTZ to any position When all operating route finished enter PTZ SET menu again and move the cursor to the END button and press ENTER button on the front panel to save the operating route to pattern 1 Using the same way to save other PTZ operating route to relevant pattern number At the PTZ SET menu select PATTERN number to 1 or other PATTERN number you wish to run Press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the PATTERN button Press ENTER button to start pattern 1 route operation Press ENTER button again to stop pattern 1 route operation Using the same way to run other pattern operation 3 AUTO SCAN a At the PTZ SET menu press CANCEL button on the front panel to exit PTZ other function setting mode and return to PTZ operation mode Press UP DOWN LEFT RIGHT and ENTER buttons to control PTZ to a position as the left position Enter the PTZ SET menu again press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the LEFT button Press ENTER button on the front panel to set the PTZ position to
57. nel to exit the keyboard box and return to the NETWORK setup menu without saving Mouse 1 Click on a number button on the keyboard box to input a number Click on button on the keyboard box to clear the previous number After input the correct IP address and click on ENTER button on the keyboard box to exit the keyboard box and return to the NETWORK setup menu 2 Right click the place out of the keyboard box on the screen to exit the keyboard box and return to the NETWORK setup menu without saving 4 MACADDRESS Press UP or DOWN button on the front panel to move the cursor to the MAC ADDRESS line at the NETWORK setup menu Press ENTER button to display a keyboard box Use the same way for setting IP address to set MAC ADDRESS 5 NETMASK Press UP or DOWN button on the front panel to move the cursor to the NETMASK line at the NETWORK setup menu Press ENTER button to display a keyboard box Use the same way for setting IP address to set NETMASK 6 GATEWAY Press UP or DOWN button on the front panel to move the cursor to the GATEWAY line at the NETWORK setup menu Press ENTER button to display a keyboard box Use the same way for setting IP address to set GATEWAY NAME SERVER Press UP or DOWN button on the front panel to move the cursor to the NAME SERVER line at the NETWORK setup menu Press ENTER button to display a keyboard box Use the same way for sett
58. nguages supported Audio and video recording and playback at the same time with D1 half D1 and CIF resolution support NTSC PAL video system 4 8 16 24 32CH video inputs ICH monitor output ICH spot monitor output for 16 24CH DVR 2CHx16 spot monitor output for 32CH DVR VGA output 800x600 1024x768 1280x1024 4 8 16CH audio inputs 8CH audio inputs for 24 32CH DVR 1CH audio output High quality image brightness contrast sharpness and color adjustable for each channel Support auto sequence display Display modes PIP FULL QUAD 9 SPLIT for 8 16 24 32CH DVR 16 SPLIT for 16 24 32CH DVR 25 for 24 32CH DVR and 36 SPLIT for 32CH DVR Recording modes always recording manual recoding schedule recording sensor recording and motion recording Image quality and bitrate highest high standard low Detailed event log support searching modes time date searching event searching urgent searching support fast forward and rewind x2 x4 x6 support jog shuttle operation for 16 32CH DVR Backup modes network backup USB backup DVDRW backup for 8 16 24 32CH DVR Support RS 485 PTZ control speed dome camera and preset positions operation Support USB mouse and infrared remote controller operation support 1 SATA port HDD for 4CH DVR and 2 SATA port HDD for 8CH DVR and 4 SATA port HDD for 16 24 32CH DVR 4 8 16 CH alarm inputs 16 CH alarm inputs for 24 32CH DVR CH alarm output 4 8 16 CH DVR 2 CH alarm output 24 32 CH DVR
59. nu displayed as below NETWORK A A v v PORT MAC ADDRESS IP ADDRESS NETMASK GATEWAY NAME SERVER DONS EMAIL BITRATE HIGHEST MOBILE PORT 15966 IE PORT 82 Aaa UUT D A a v v v SAVE EXIT 1 IPMODE Press UP or DOWN button on the front panel to move the cursor to the IP MODE line at the NETWORK setup menu Press LEFT RIGHT button to select the network IP mode The IP mode can be set to STATIC DHCP or PPPoE Select OFF to disable network connection 2 PORT Press UP or DOWN button on the front panel to move the cursor to the PORT line at the NETWORK setup menu Press LEFT RIGHT button to select the network server port 3 IPADDRESS Press UP or DOWN button on the front panel to move the cursor to the IP ADDRESS line at the NETWORK setup menu Press ENTER button to display a keyboard box The keyboard box displayed as below KEYBOARD Space Bar 1 Press UP DOWN LEFT or RIGHT button on the front panel to move cursor to select a number then press ENTER button on the front panel to input this number Select lt on the keyboard box to clear the previous number After input the correct IP address and move the cursor to ENTER on the keyboard box press ENTER button on the front panel to exit the keyboard box and return to the NETWORK setup menu 2 Press CANCEL button on the front pa
60. ny user line at the ACCOUNT MANAGER menu Click on the SET button to display MODIFY USER menu Move the cursor to the USER PASSWORD and click on the SET button to open keyboard box to modify the password Move the cursor to the other selectable item of authority list at the MODIFY USER menu Click on the relevant item to select or unselect the authority for the user Click on the SAVE button to save the setting and return back to previous menu If login user is admin move the cursor to ADD USER line at the ACCOUNT MANAGER menu Click on the SET button to display ADD USER menu Move the cursor to the USERNAME and the USER PASSWORD line and click on the SET button to open keyboard box to set a user name and the password for this new user Move the cursor to the other selectable items of authority list at the ADD USER menu Click on the relevant item to select or unselect the authority for the new user When the item is selected and ticked the user is allowed to operate this function Click on the SAVE button to save the setting and return back to previous menu If login user is admin move the cursor to a normal user line at the ACCOUNT MANAGER menu Click on the CANCEL button on the right side of the user line to delete the normal user and display a WARNNING box Click on the YES button to delete the user If login user is not admin using the same way to change itself password and authority at the MODIFY USER m
61. o select backup beginning date time and end date time 2 Click on the top right O OK button to begin backup If no any backup device connected to the DVR when beginning the backup it will display the information that no backup device found 3 8 SYSTEM Menu Setup Press MENU button on the front panel to display MAIN MENU during the live display mode Press UP DOWN LEFT and RIGHT buttons to select SYSTEM button in the MAIN MENU and press ENTER button to enter SYSTEM setup menu After setting press MENU button to save the setting Then exit the submenu and main menu Press CANCEL button to exit submenu without saving The SYSTEM setup menu displayed as below x SYSTEM ttt y a A v Y 1 TIME SETUP Press UP or DOWN button on the front panel to move the cursor to the TIME SETUP line and press ENTER button to display the TIME SET menu Press UP DOWN LEFT or RIGHT button to set the current date time and select display format of date time at the TIME SET menu There are 3 display formats for date time ASIA EURO and US Press ENTER button to return to the SYSTEM setup menu Press UP or DOWN button to ZONE and press LEFT or RIGHT button to select the local area zone Press UP or DOWN button to SERVER and press MENU button to set a IP address of time server or keep the de
62. onitor 32CH Audio Output 8db3k RCA connector X 1 4CH CIF NTSC 120fps 352x240 PAL 100fps 352x288 1 2D1 NTSC 120fps 720x240 PAL 100fps 720x288 Di NTSC 60fps 720x480 PAL 50fps 720x576 SCH CIF NTSC 240fps 352x240 PAL 200fps 352x288 1 2D1 NTSC 120fps 720x240 PAL 100fps 720x288 Di NTSC 60fps 720x480 PAL 50fps 720x576 Frame and Resolution 16CH CIF NTSC 480fps 352x240 PAL 400fps 352x288 1 2D1 NTSC 240fps 720x240 PAL 200fps 720x288 Di NTSC 120fps 720x480 PAL 100fps 720x576 24CH CIF NTSC 720fps 352x240 PAL 600fps 352x288 32CH CIF NTSC 960fps 352x240 PAL 800fps 352x288 HDD Port SATA hard disk X 1 4CH X 2 8CH X 4 16 24 32CH 10M 100M 4 8 16 24 32CH 10M 100M 1000M 16CH Network Port Ethernet port Windows mobile Symbian iPhone Android Blackberry support SMTP server support SSL Password Protection DC 12V 2A 4CH 3A 8CH 5A 16 24 32CH lt 10W 4 8CH 15W 16 24CH 20W 32CH Operating Temperature 0 C 455 C Environment m Humidity 10 90 l 330 X 250 X 60mm 4 8CH 430 X 350 X 90mm 16 24 32CH Dimension a 280 X 230 X 36mm Mini 4CH Monitor Output
63. or free DDNS make sure the DVR can be connected to internet SERVER HOSTNAME USERNAME DONS UPNP press UP or DOWN button on the front panel or use the mouse to move the cursor to the UPNP then press ENTER button or click the mouse to select UPNP After quit the submenu and main menu it will enable the UPNP for your Router When setting UPNP make sure the UPNP function of Router is turned on EMAIL Press UP or DOWN button on the front panel to move the cursor to the EMAIL line at the NETWORK setup menu Press ENTER button to display the EMAIL setup menu The EMAIL setup menu displayed as below EMAIL SSL SMTP PORT SMTP SENDER EMAIL SEND PW RECV EMAIL 1 Press UP or DOWN button on the front panel to move the cursor to the EMAIL line at the EMAIL setup menu Press LEFT RIGHT button to select ON or OFF When selecting OFF the EMAIL function is disabled 2 When setting EMAIL to ON press UP or DOWN button on the front panel to move the cursor to the SSL line and press LEFT RIGHT button to select ON or OFF to turn on or off SSL press UP or DOWN button on the front panel to move the cursor to the SMTP PORT SMTP SENDER EMAIL SEND PW and RECV EMAIL line at the EMAIL setup menu Press MENU button to display a keyboard box Using the same way for setting IP address to set them 10 BITRATE 1 Press
64. r X6 during the playback In PTZ operation mode press this button to control tilt up gt Press this button to display a still picture during the playback press this button again to restart play In PTZ operation mode press this button to control tilt down Pb Repeat pressing this button to speed up playback forward at the speed of X2 X4 or X6 during the playback SEARCH Enter the playback mode and display the search menu In PTZ operation mode press this button to control pan right For Mini 4CH DVR in the playback mode press this button to turn on or off the playback audio In SCHEDULE setup mode press this button to select different recording mode B Press this button to stop the playback during the playback MENU Display the setup menu during the live display mode In PTZ operation mode and CAMERA COLOR menu press this button to make PTZ menu and CAMERA COLOR menu transparent ESC In the setup menu or PTZ operation mode press this button to exit the menu or PTZ operation mode REC Begin and stop manual recording In PTZ operation mode press this button to control pan left PTZ Enter PTZ operation mode and display PTZ menu MUTE Turn audio on off during the live display mode or playback mode BACKUP Enter the backup mode and display the backup menu during the live display mode AUTO Begin auto sequence function during the live display mode In PTZ operation mode press this button to enter PTZ auto pan control f
65. ring the playback mode of one channel press MUTE button on the front panel to enter playback audio volume setting mode Press LEFT or RIGHT button to decrease or increase the playback audio volume Press CANCEL button to exit playback audio volume setting mode For Mini 4CH DVR press SEARCH button on the front panel to enter playback audio volume setting mode Press LEFT or RIGHT button to decrease or increase the playback audio volume Press CANCEL button to exit playback audio volume setting mode 7 During the playback mode press CANCEL button to stop playback and return to previous mode 6 JOG amp SHUTTLE For 16 3CH DVR During the playback mode turn the SHUTTLE ring to the right or left to select speed of FAST FORWARD or REWIND playback Turn the JOG dial in either direction continuously for playback of consecutive frames Mouse Click the mouse on the MENU icon on the bottom status bar to display POPUP MENU during the live display mode Click on the SEARCH button to display SEARCH MENU Then click on the TIME SEARCH EVENT SEARCH or URGENT SEARCH button to select the playback modes to begin playback Or double click the date time to begin playback During the single channel playback mode turn the middle button of mouse to select other cameras displaying on the screen To zoom in images can only be operated by mouse During the playback mode select the desired sin
66. s UP or DOWN button on the front panel to move the cursor to the BITRATE line at the RECORD setup menu Press LEFT or RIGHT button to select the bit rate of recording h264 stream 2 The stream bit rate can be selected to HIGHEST HIGH STANDARD and LOW The higher the bit rate set the higher recording image quality get and the bigger the HDD size used RECORD MODE 1 Press UP or DOWN button on the front panel to move the cursor to the RECORD MODE line at the RECORD setup menu Press LEFT or RIGHT button to select recording mode 2 The recording mode can be selected to ALWAYS MOTION SENSOR SCHEDULE OFF When setting it to OFF the manual recording mode can be used 8 AUDIO 1 Press UP or DOWN button on the front panel to move the cursor to the AUDIO line at the RECORD setup menu Press LEFT or RIGHT button to set audio on or off 2 When setting AUDIO to ON the system will record input audio of this channel When setting AUDIO to OFF the system will not record input audio of this channel 9 SCHEDULE 1 Press UP or DOWN button on the front panel to move the cursor to the SCHEDULE line at the RECORD setup menu Press LEFT or RIGHT button to select schedule list number If selecting SCHEDULE record mode the recording is according to this schedule list that setting at the SCHEDULE setup menu 2 There are totally 5 schedule lists
67. s pause play button to return to normal playback Press this button to move the cursor in right direction in the setup menu In PTZ operation mode press this button to move the cursor right to select function For Mini 4CH DVR in the playback mode press this button to select different playback control mode PLAY PAUSE BACKWARD FAST FORWARD STEP FORWORD 6 3 20 Bower indicator Indicate running state of system It s on when system power on 21 Shap status indicator Flicker when HDD is working 22 Bb recording status indicator It will be on when system is recording 23 EN on status indicator It will be on when the system network connection is enabled 24 FEN status indicator It will be on when alarm occur 25 2 Mouse port Connector for the USB mouse 26 v port Connection of the USB interface device for upgrading firmware and backup recorded files 27 DVDRW or CDRW ROM SATA interface For 16 24 32CH DVR 28 5 sensor Input sensor for the remote controller 1 2 Rear Panel Connectors VIDEO IN AUDIO IN 4 CH DVR VIDEO OUT At t gt DEM RS485 1 8CH ALARM DC 12 8CH DVR 10 16 CH DVR Mini 16 CH DVR i rz uw e c at Ra gt JO eoo d pIa a a gt i eoo a rie rx ooo e ic ae piai eoo Ru rx rr ar e 24 CH DVR a T f a T poy eere Berd Le ao
68. se 1 Click the mouse on the MENU icon on the bottom status bar to display POPUP MENU during the live display mode The POPUP MENU displayed as below LIVE Select the different screen display mode QUAD 2X2 PIP 9 SPLIT 3 X3 For 8 16CH DVR 25 SPLIT 5X5 For 24 32CH DVR and 36 SPLIT 6 X 6 For 32CH DVR SETUP Enter the system setup mode and display MAIN MENU SEARCH Enter the playback mode and display the search menu EMG RECORD Begin and stop manual recording ZOOM Enter image zoom in function only operated by mouse PTZ Enter PTZ operation mode and display PTZ menu ROTATION Start or stop auto sequence function AUDIO ON OFF Turn audio on off during the live display mode LOGIN Select a valid user name and password to login QUIT Power off the DVR 2 At the POPUP MENU Click on the SETUP button to display MAIN MENU Click on the submenu button to enter relevant submenu 3 Inthe MAIN MENU right click the place out of the MAIN MENU on the screen to exit the MAIN MENU 3 2 CAMERA Menu Setup Press MENU button on the front panel to display MAIN MENU during the live display mode Press UP DOWN LEFT and RIGHT buttons to select CAMERA button in the MAIN MENU and press ENTER button to enter CAMERA setup menu After setting press MENU button to save the setting Then exit the submenu and main menu Press CANCEL button to exit submenu without saving The CAMERA setup menu
69. ss LEFT or RIGHT button to select different schedule recording list There are totally 5 schedule recording lists to select 7 Press ENTER button to save the setting and exit the SCHEDULE setup menu Mouse 1 Click on the MOTION button to select the MOTION schedule recording mode at the SCHEDULE setup menu Or click on the SENSOR button to select the SENSOR schedule recording mode Or click on the ALWAYS button to select the ALWAYS schedule recording mode Or click on the CANCEL button to select the OFF schedule recording mode 2 Move the cursor to the desired day from Monday to Sunday and time from 0 to 24 Click the left mouse button to set the day and time to the selected schedule recording mode 3 Move the cursor to the SCHEDULE list button and turn the middle button of mouse to select different schedule recording list There are totally 5 schedule recording lists to select 4 Click on the top right O OK button to save the setting and exit the SCHEDULE setup menu NETWORK Menu Setup Press MENU button on the front panel to display MAIN MENU during the live display mode Press UP DOWN LEFT and RIGHT buttons to select NETWORK button in the MAIN MENU and press ENTER button to enter NETWORK setup menu After setting press MENU button to save the setting Then exit the submenu and main menu Press CANCEL button to exit submenu without saving The NETWORK setup me
70. t already set before can not be set again If needs to set the same area again must clear the area first 3 Press UP or DOWN button to select CLEAR AREA 1 at the cover area setting menu Press ENTER button to clear cover area 1 and the cleared area will become gray color Using the same way to clear cover area 2 and cover area 3 4 Press UP or DOWN button to select EXIT in the cover area setting menu Press ENTER button to return back to the CAMERA setup menu The covered area can not display video for the live playback and network viewing 3 3 RECORD Menu Setup Press MENU button on the front panel to display MAIN MENU during the live display mode Press UP DOWN LEFT and RIGHT buttons to select RECORD button in the MAIN MENU and press ENTER button to enter RECORD setup menu After setting press MENU button to save the setting Then exit the submenu and main menu Press CANCEL button to exit submenu without saving The RECORD setup menu displayed as below RECORD CHANNEL ALL RESOLUTION CII PRE RECORD OFI QUALITY HIGHEST BITRATE HIGHEST RECORD MODI MOTION AUDIO ON SCHEDULE SCHEDULE SYSTEM MAINTENANCE 1 CHANNEL Press UP or DOWN button on the front panel to move the cursor to the CHANNEL line at the RECORD setup menu Press LEFT RIGHT button to select the channel to set Select ALL to set all channels When selecting
71. t the tag and set the parameter of DVR Click the Save button to change and save the new parameter to the DVR If the internet speed is very low it may be fail to set the new parameter and it will popup the message box to display the warning of time out 5 The default mode of NetViwer is live mode It will display the live image of DVR The control buttons are as below button to change NetViwer to playback After connection with DVR click on the e mode It can select the playing date and time and play back the DVR recording file The control buttons are as below ate Select the live mode Prey Select the local file play mode a O O i Sto the playback of DVR recording fle ie Faroa Paya B Rewind Playback OOOO Select a channel EN Start date of playback Start time of playback Click on the EZZZZE button to change NetViwer to local mode It can open the pc local folder and select the recording backup file By USB device etc and play it The control buttons are as below a 000 lg Stop plying recording backup file i Previous fle OOO M TT Leamor pymp SSCS E Next frame offie paying SSS C EFN B8 X Open button for playing file Click on the button to change NetViwer to live mode VI SPECIFICATION Video System NTSC PAL Video Input Composite 1 0Vp p 75 8 BNC X 4 8 16 24 32 1 0Vp p Composite 75 9 BNC X 1 monitor BNC X 1 spot monitor 16 24CH BNC X 2 spot m
72. the left position At the PTZ SET menu press CANCEL button on the front panel to exit PTZ other function setting mode and return to PTZ operation mode Press UP DOWN LEFT RIGHT and ENTER buttons to control PTZ to a position as the right position Enter the PTZ SET menu again press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the RIGHT button Press ENTER button on the front panel to set the PTZ position to the right position At the PTZ SET menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the AUTOSCAN button Press ENTER button to start PTZ auto scan between the left position and the right position Press ENTER button again to stop PTZ auto scan 4 Others a At the PTZ SET menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the FLIP button Press ENTER button on the front panel to flip the PTZ At the PTZ SET menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the RESET button Press ENTER button on the front panel to reset the PTZ At the PTZ SET menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the LIGHT button Press ENTER button on the front panel to turn on the light Press ENTER bu
73. to the SENSOR CHANNEL line at the SENSOR setup menu Press LEFT RIGHT button to select the channel to set Select ALL to set all channels When selecting ALL if one item display it means that this feature item of each channel is different When saving the setting if the item selected the setting of this item is not changed 2 SENSOR TYPE Press UP or DOWN button on the front panel to move the cursor to the SENSOR TYPE line at the SENSOR setup menu Press LEFT RIGHT button to select the sensor type NORMAL CLOSE or NORMAL OPEN 3 POST RECORD TIME 1 Press UP or DOWN button on the front panel to move the cursor to the POST RECORD TIME line at the SENSOR setup menu Press LEFT or RIGHT button to select post alarm recording time 2 The post alarm recording time can be set from 10 second to 60 When setting it to OFF the post alarm recording time is 0 second 4 BUZZER TIME 1 Press UP or DOWN button on the front panel to move the cursor to the BUZZER TIME line at the SENSOR setup menu Press LEFT or RIGHT button to select beep sound time 2 The beep sound time can be set from 1 second to 60 second When setting it to OFF the beep does not sound 5 ALARM TIME 1 Press UP or DOWN button on the front panel to move the cursor to the ALARM TIME line at the SENSOR setup menu Press LEFT or RIGHT b
74. tton again on the front panel to turn off the light At the PTZ SET menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the WIPER button Press ENTER button on the front panel to start using wiper Press ENTER button again on the front panel to stop using wiper At the PTZ SET menu press LEFT RIGHT UP or DOWN button on the front panel to move the cursor to the CAMPOWER button Press ENTER button on the front panel to turn on the camera power Press ENTER button again on the front panel to turn off the camera power If it supports menu or matrix operation for the PTZ protocol this button is MENU button for PTZ and press ENTER button on the front panel to enter PTZ MENU MATRIX setup menu Mouse 1 In PTZ operation mode click on SET button at the menu to display PTZ SET menu and enter PTZ other function setting mode 2 PATTERN a Atthe PTZ SET menu move the cursor to the PATTERN frame Turn the middle button of mouse to set PATTERN number to 1 Click on the BEGIN button to start pattern setting b Click on CANCEL button or right click to exit PTZ other function setting mode and return to PTZ operation mode Click on the direction arrows and zoom focus iris icons to control PTZ to any position When all operating route finished enter PTZ SET menu again and click on the END button to save the operating route to pattern 1 Usin
75. tton to display the CALENDAR menu Press LEFT or RIGHT button to select the date at the CALENDAR menu and press ENTER button to return to the BACKUP setup menu TOTAL If the USB or SATA DVDRW device is connected to this DVR and START date time END date time set correctly it will display the selected backup file size AVI If the USB or SATA DVDRW device is connected to this DVR press LEFT or RIGHT button on the front panel to move the cursor to AVI icon and press MENU button to select AVI Press MENU button again not to select AVI When select AVI the type of the backup file in USB device is AVI format and backup channel is only one channel DISK HDD 01 DEVICE USB CHANNEL 1 START 2011 01 19 16 3 END 2011 01 19 17 TOTAL 69 MB 8 Press ENTER button on the front panel to display warning box Press ENTER button on the front panel again to begin format USB device and then start backup Press CANCEL button on the front panel to start backup without USB device format DO YOU WANT TO FORMAT USB DEVICE y oe When the backup is completed it will return back the BACKUP setup menu Mouse 1 At the BACKUP setup menu if the USB or SATA DVDRW device is connected to the DVR move the cursor to the CHANNEL START or END line Click on the SET button to select the backup channel backup beginning date time and end date time or turn the middle button of mouse t
76. unction press this button again to exit PTZ auto pan control function MODE Select the different screen display FULL CHANNEL PIP QUAD 9 SPLIT 16 25 36 SPLIT during the live display mode or playback mode A Press this button to move the cursor up to the next line in the setup menu After pressing MODE button press this button to select last camera displaying on the screen In PTZ operation mode press this button to move the cursor up to select function Press this button to move the cursor in left direction in the setup menu In PTZ operation mode press this button to move the cursor left to select function lt 1 During the live display mode press this button to display the popup menu In the setup menu press this button to enter the next operation In PTZ operation mode press this button to enter PTZ operation For Mini 4CH DVR in the playback mode press this button to enter different playback control mode P Press this button to move the cursor in right direction in the setup menu In the playback mode press this button to enter step forward playback In PTZ operation mode press this button to move the cursor right to select function 19 V Press this button to move the cursor down to the next line in the setup menu After pressing MODE button press this button to select next camera displaying on the screen In PTZ operation mode press this button to move the cursor down to select function 1
77. utton to move the cursor to SPEED frame press UP or DOWN button to set the pan tilt speed from 1 to 6 Press LEFT RIGHT UP or DOWN button to move the cursor to PRESET button press ENTER button to display PTZ PRESET menu and enter PTZ preset function setting 7 Press LEFT RIGHT UP or DOWN button to move the cursor to SET button press ENTER button to display PTZ SET menu and enter PTZ other functions setting 8 If PTZ protocol supports position function it will display word SIT on the round icon among pan tilt arrows Press LEFT RIGHT UP or DOWN button to move the cursor to SIT icon press ENTER button to operate PTZ position function 9 Press CANCEL button on the front panel to exit the PTZ operation mode 10 Press MENU button on the front panel to make the PTZ menu transparent Mouse 1 Left click the desired camera screen to select this single channel to display on the monitor during the live display mode Click the mouse on the MENU icon on the bottom status bar to display POPUP MENU during the live display mode Then click on the PTZ line to display PTZ control menu and enter the PTZ operation mode 2 At the PTZ control menu click or keep pressing the mouse left button on LEFT or RIGHT arrow to control pan function Click or keep pressing the mouse left button on UP or DOWN
78. utton to select post output alarm time 2 The post alarm time can be set from 1 second to 60 second When setting it to OFF the alarm does not output 6 HDD LOSS 1 Press UP or DOWN button on the front panel to move the cursor to the HDD LOSS line at the SENSOR setup menu Press LEFT or RIGHT button to select HDD loss alarm time 2 The beep sound time of HDD loss can be set from 1 second to 30 second When HDD is out of action or DVR cannot detect the HDD the beep of alarm will sound for the setting duration When setting it to OFF the beep does not sound 7 VIDEO LOSS 1 Press UP or DOWN button on the front panel to move the cursor to the VIDEO LOSS line at the SENSOR setup menu Press LEFT or RIGHT button to select video loss alarm time 2 The beep sound time of video loss can be set from 1 second to 30 second When video of a channel loss the beep of alarm will sound for the setting duration and the letter L will be displayed on the channel When setting it to OFF the beep does not sound 8 HDDFULL 1 Press UP or DOWN button on the front panel to move the cursor to the HDD FULL line at the SENSOR setup menu Press LEFT or RIGHT button to select HDD full alarm time 2 The beep sound time of HDD full can be set from 1 second to 30 second When the HDD is full of recording the beep of alarm will sound for the setting duration When setting it to OFF th
79. ving the display image as AVI file in the PC local Meu Mj TT Eeee or disable te recording ia the PC loca dieto MB San emamalcodofDVR MN Sep emamalrcodofDVR BM Erabi or disabte thead oo Enable or disable the automatic connection Minimum of the net viewer window Setup the connection and start to connect to DVR 3 Click the m button as below Login Address Del Port Username Password Network WAN cancel Input IP address of DVR it can be saved automatically or free DDNS user name port number default is 2200 no need to input port number when using free DDNS user name password default is no password and select LAN or internet of your network in the Login window Click the OK button to finish setting and start to connect to the DVR Click the Del button to delete the saved IP address 4 If the DVR is connected Click the ad button to enter parameter setup window as below Camera HOD Hetwork Sehedule Sensor System Other Save Camera N Title cni Protocol PELCO n Address p Baudrate 2400 MainRotTime 3 Color Contras 50 Brigh 50 Hue so Stee S Sharp m 7 Record Mation Enable OFF FPS Sensitivi LEVEL 4 Quality Moti omar e SUIS Audio PoztRecordTime o Mode us 5 Schedule scemu 1 T B CIE v BurzzerTime AlarmTime Rezoluti Bitrat PreRecord Selec

4/8/16/24/32 CHANNEL H.264 DVR - Sunsky

Contents

Download Pdf Manuals

Related Search

Related Contents