Industrial Management Ethernet Switch
Contents
1. IDS M311 Industrial Modbus Gateway User Manual Version 1 0 JUN 2014 www oring networking com ORing Industrial Networking Corp LZ ORing IDS M311 Series User Manual COPYRIGHT NOTICE Copyright O 2014 ORing Industrial Networking Corp AIl rights reserved No part of this publication may be reproduced in any form without the prior written consent of ORing Industrial Networking Corp TRADEMARKS ORing is a registered trademark of ORing Industrial Networking Corp All other trademarks belong to their respective owners REGULATORY COMPLIANCE STATEMENT Product s associated with this publication complies comply with all applicable regulations Please refer to the Technical Specifications section for more details WARRANTY ORing warrants that all ORing products are free from defects in material and workmanship for a specified warranty period from the invoice date 5 years for most products ORing will repair or replace products found by ORing to be defective within this warranty period with shipment expenses apportioned by ORing and the distributor This warranty does not cover product modifications or repairs done by persons other than ORing approved personnel and this warranty does not apply to ORing products that are misused abused improperly installed or damaged by accidents Please refer to the Technical Specifications section for the actual warranty period s of the product s associated with this public2. PM E ETA LHKIACT TUFE room for sliding the wall mount panel between the wall and the screws Note Instead of screwing the screws in all the way leave about 2 mm to allow 3 3 Wiring 2 WARNING Do not disconnect modules or wires unless power has been switched off or the area is known to be non hazardous The devices may only be connected to the supply voltage shown on the type plate ATTENTION 1 Be sure to disconnect the power cord before installing and or wiring your devices Calculate the maximum possible current in each power wire and common wire Observe all electrical codes dictating the maximum current allowable for each wire size If the current goes above the maximum ratings the wiring could overheat causing serious damage to your equipment Use separate paths to route wiring for power and devices If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point Do not run signal or communications wiring and power wiring through the same wire conduit To avoid interference wires with different signal characteristics should be routed separately You can use the type of signal transmitted through a wire to determine which wires should be kept separate The rule of thumb is that wiring sharing similar electrical characteristics can be bundled together You should separate input wiring from output wiring It is advised to label the wiring to all devic
3. 3 RS EN61000 4 4 EFT EN61000 4 5 Surge EN61000 4 6 CS EN61000 4 8 EN61000 4 11 ORing Industrial Networking Corp 22 ORing IDS M311 Series User Manual Free Fall IEC60068 2 32 Safety EN60950 1 Warranty 5 years ORing Industrial Networking Corp 23
4. RS 485 4W Baud Rate Choose a baud rate in the range between 110 bps and 11520 bps Data Bits Choose the number of data bits to transmit You can configure data bits to be 5 6 7 or 8 Data is transmitted as a series of five six seven or eight bits five and six bit data formats are used rarely for specialized communications equipment Stop Bits Choose the number of bits used to indicate the end of a byte You can configure stop bits to be 1 or 1 5 2 If Stop Bits is 1 5 the ORing Industrial Networking Corp 15 ORing IDS M311 Series User Manual stop bit is transferred for 150 of the normal time used to transfer one bit Both the computer and the peripheral device must be configured to transmit the same number of stop bits Chose the method of detecting errors in transmission Parity control bit modes include None Odd Even Mark and Space None means parity checking is not performed and the parity bit is not transmitted Odd means the number of mark bits in the data is counted and the parity bit is asserted or unasserted to obtain an odd number of mark bits Even means the number of mark bits in the data is counted and the parity bit is asserted or unasserted to obtain an even number of mark bits Flow Control Choose XOFF to tell the computer to stop sending data or XON to tell the computer to begin sending data again 5 2 2 Service Mode This page allows you to configure the parameters for individua
5. simultaneous connections Supported serial interfaces include RS 232 and RS 422 485 selectable through software The serial port can be connected to one RS 232 or RS 422 serial device or to 32 RS 485 serial devices The IDS M311 can be used in several applications including linking Ethernet masters with multiple serial slaves serial masters with multiple Ethernet slaves Modbus TCP masters with ASCII and RTU slaves and serial master with serial slaves over Internet Connect Modbus TCP Master to Serial Modbus RTU or Modbus ASCll Slaves Modbus RTU or Modbus ASCII Modbus TCP Master Ethernet IDS M311 Slaves Network Modbus TCP Modbus TCP 4 gt 4 p PLC HMI SCADA OPC server etc Connect Modbus Serial Masters to Modbus TCP Slaves Firmware Modbus Router Modbus TCP Ethernet Modbus RTU Slaves Network DeviceMaster UP or Modbus ASCIl IDS M311 Slaves Modbus TCP Modbus TCP RS 232 l PLC HMI PLC HMI SCADA SCADA ete A OPC server etc ORing Industrial Networking Corp 12 ORing IDS M311 Series User Manual Management The device can be managed via a built in web server which supports Internet Explorer Internet Explorer 5 0 or above versions and other Web browsers such as Chrome Therefore you can manage and configure the device easily and remotely You can also upgrade firmware via a Web browser The Web management function not only reduces network bandwidth consumption but also enhances access
6. speed and provides a user friendly viewing screen Note By default IE5 0 or later version do not allow Java applets to open sockets You need to modify the browser setting separately in order to enable Java applets for network ports Management via Web Browser Follow the steps below to manage your device via a Web browser System Login 1 Launch an Internet Explorer 2 Type http and the IP address of the device Press Enter A login screen appears Type in the username and password The default username and password is admin 5 Press Enter or click OK the management page appears Windows Security Enter Network Password Enter your password to connect to PC SWRD19 admin LELEL P Domain ORING Remember my credentials 9 Logon failure unknown user name or bad password Cancel Note you can use the following default values IP Address 192 168 10 1 Subnet Mask 255 255 255 0 Default Gateway 192 168 10 254 ORing Industrial Networking Corp 13 ORing IDS M311 Series User Manual User Name admin Password admin After logging in you will see the information of the device as below system Information LAN IF Address 192 188 10 3 LAN MAC Address 00 1E 94 50 00 40 Firmware Version 1 00 On the left hand side of the management interface shows links to various settings Clicking on the links will bring you to individual configuration pages 5 1 Network Configur
7. 3 5 Firmware Upgrade This page allows you to update the firmware of the device To upgrade you need a firmware files correspond to this Device model It will take several minutes to upload and upgrade firmware Do not turn of the power during firmware upgrade After upgrade is completed the device will reboot and be revalidated Upgrade Firmware Specify the firmware image to upgrade Note Please DO NOT power off this device while Upgrading firmware Firmware Rs EEE Wograde ORing Industrial Networking Corp 20 ORing 5 3 6 Restart Device You can reboot the device by click Reboot button Please click Reboot button to restart device Reboot ORing Industrial Networking Corp IDS M311 Series User Manual 21 ORing IDS M311 Series User Manual Technical Specifications Physical Ports 10 100 Base T X Ports in RJ45 a EKA Serial Ports Network Protocol ICMP IP TCP UDP DHCP BOOTP DNS SNMP V1 V2c HTTPS SMTP DDNS PPPoE Modbus TCP LED indicators PWR 1 2 Ready Red On Power is on and booting up Power indicator Red Blinking Indicates an IP conflict or DHCP or BOOTP server did not respond properly Green On Power is on and functioning Normally Green Blinking Located by Administrator Green Serial port is transmitting data Power Physical Characteristic Environmental 5 to 95 Non condensing W Regulatory approvals EN61000 4 2 ESD EN61000 4
8. ation DISCLAIMER Information in this publication is intended to be accurate ORing shall not be responsible for its use or infringements on third parties as a result of its use There may occasionally be unintentional errors on this publication ORing reserves the right to revise the contents of this publication without notice CONTACT INFORMATION ORing Industrial Networking Corp 3F NO 542 2 Jhongjheng Rd Sindian District New Taipei City 231 Taiwan R O C Tel 886 2 2218 1066 Fax 886 2 2218 1014 Website www oring networking com Technical Support E mail support oring networking com Sales Contact E mail sales oring networking com Headquarters sales oring networking com cn China ORing Industrial Networking Corp l ORing IDS M311 Series User Manual Table of Content Geno EE ln e WEE 3 1 1 POU E NN 3 1 2 S ltwale WE sisimat atakk 3 1 3 Hardware Specifications n nennenennene nene nnnannnnannnne nene naene annan 3 HAA WAS e WEE 4 2 1 TOD FING E EE E E amaan E 4 Sted FPO ANTONE OS E 4 2 2 FOI st A Sl EE 4 en WER BC RE 5 2 3 BOOM ING I ss aaa a a a a a 5 ale Wale INSTA AMON ates as aan tia kina iivet aia cess cous cesvectuctvucoductsecevuctcccedesscucsves 6 2 4 DIN rail WAS VN IG EE 6 3 2 WANI OUNIDO EE 7 3 3 Millal etem m mme 8 SS a HS e Die Le lee ccc cece E sc strc ston eine teint peste meee eee 9 99392 M dundant POWER ADIN E 9 3 4 E nl ed oo mee sma nene aid
9. ation This page allows you to configure the network functions of the device 5 1 1 IP Configuration This page shows the general information of the device You can assign an IP for the device manually or have the DHCP server assign the IP automatically Select Static IP if you are using a fixed IP address Click Apply after you complete configuration IP Configuration IP Configuration Static IP Address Netmask 255 255 255 0 Gateway 192 168 10 1 DNS Server 1 197 169 10 1 DNS Server 2 IP Configuration Choose to use a static or DHCP assigned IP If you choose ORing Industrial Networking Corp 14 ORing IDS M311 Series User Manual 1 DHCP the following fields will gray out Enter the IP address that identifies the server on the TCP IP IP Address network Enter a subnet mask for the device Enter the IP address of the router that provides network access Gateway outside the server s LAN Enter the IP address of the primary and secondary domain name DNS Server 1 2 server 5 2 Port Serial Setting 5 2 1 Serial Configuration This page allows you to configure serial port parameters serial Configuration Forti Fort Alias porta Interface R 5232 T Baud Rate 25400 Y Data Bits GT Stop Bits 1 Parity None Y Flaw Control None Port Alias Enter the COM port number that modem is connected to Choose an interface for your serial device Available interfaces include RS 232 RS 422 RS 485 2W and
10. es in the system ORing Industrial Networking Corp 8 ORing IDS M311 Series User Manual 3 3 1 Grounding Grounding and wire routing help limit the effects of noise due to electromagnetic interference EMI Run the ground connection from the ground pin on the power module to the grounding surface prior to connecting devices 3 3 2 Redundant Power Inputs The device has two sets of power inputs in the form of DC power jack and terminal The power input connectors are located on the top panel alongside the Ethernet port Follow the steps below to wire the power input on the terminal block Step 1 insert the negative positive wires into the V V terminals respectively Step 2 to keep the wires from pulling loose use a small flat blade screwdriver to tighten the wire clamp screws on the front of the terminal block connector 3 4 Connection 3 4 1 Cables 10 100BASE T X Pin Assignments The device has a standard Ethernet port According to the link type the device uses CAT 3 4 5 5e UTP cables to connect to any other network devices PCs servers switches routers or hubs Please refer to the following table for cable specifications Cable Types and Specifications Cable Max Length Connector 10BASE T Cat 3 4 5 100 ohm UTP 100 m 828 ft RJ 45 100BASE TX Cat 5 100 ohm UTP UTP 100 m 828 ft RJ 45 With 10 100Base T X cables pins 1 and 2 are used for transmitting data and pins 3 and 6 are used for receiv
11. guration Device Name IDS ME11 Device Description IC 5 F1311 Tirne SMTP Enable Disable Time Zone GMT 08 00 Taipei Local Time Fri Jan 01 2010 09 55 10 Time Serwer poal ntp org Device Name Enter the model name of the device Device Enter the description for the device Description ORing Industrial Networking Corp 17 ORing IDS M311 Series User Manual SNTP Enable or disable SNTP function Time Zone Choose the time zone according to the location of the device Set up the local time Enter the address of the time server The following table lists different location time zones for your reference November Time Zone ADT Atlantic Daylight AST Atlantic Standard EDT Eastern 4 hours 8am EST Eastern Standard CDT Central 5 hours 7am CST Central Standard MDT Mountain 6 hours 6am MST Mountain Standard PDT Pacific 7 hours 5am PST Pacific Standard ADT Alaskan 8 hours 4am ALA Alaskan Standard 3 am HAW Hawaiian Standard 2 am GET Central European FWT French 1 hour 1 pm Winter MET Middle European MEWT Middle European Winter SWT Swedish Winter ZP4 USSR Zone 3 4 pm ZP5 USSR Zone 4 5 pm ZP6 USSR Zone 5 6 pm ORing Industrial Networking Corp 18 ORing IDS M311 Series User Manual Standard GST Guam Standard USSR Zone 9 IDLE International Date Line NZST New 12 hours Midnight Zealand Standard NZT New Zealand 5 3 2 Login Setting This page allow
12. ing data 10 100 Base T X RJ 45 Pin Assignments RD ORing Industrial Networking Corp 9 e men The device also supports auto MDI MDI X operation You can use a cable to connect the device to a PC The table below shows the 10 100Base T X MDI and MDI X port pin outs 10 100 Base T X MDI MDI X Pin Assignments TD transmit RD receive TD transmit RD receive RD receive TD transmit oe RECH RD receive TD transmit Note and signs represent the polarity of the wires that make up each wire pair DB9 console port wiring The device can be connected to a serial device using a DB9 cable The DB9 connector supports RS232 RS422 RS485 operation modes Please refer to the following table for the pin assignments of the DB9 connector A A DBS connector ORing Industrial Networking Corp 10 ORing RS 232 mod act as DTE ORing Industrial Networking Corp RS 485 2 wire IDS M311 Series User Manual Pin RS 232 RS 422 j lita s d wire 11 ORing IDS M311 Series User Manual Applications IDS M311 enables Modbus serial slaves to be integrated with existing Modbus TCP networks and serial masters to access Modbus TCP slaves Since most modern PLCs and host computers support Modbus TCP over Ethernet you can use the IDS M311 to access discrete Modbus RTU ASCII devices for data collection and control The IDS M311 supports Modbus TCP with up to 16
13. ion 2 4 DIN rail Installation The device comes with a DIN rail kit to allow you to fasten the device to a DIN rail in any environments 15 40 33 123 40 DIN rail Kit Measurement unit mm Installing the device on the DIN rail is easy First screw the Din rail kit onto the back of the device right in the middle of the back panel Then slide the device onto a DIN rail from the Din rail kit and make sure the device clicks into the rail firmly ORing Industrial Networking Corp 6 3 2 Wall Mounting Besides Din rail the device can be fixed to the wall via a wall mount panel which can be found in the package 58 00 BE EE ASS aaa 48 00 123 40 Wall Mount Kit Measurement unit mm To mount the device onto the wall follow the steps 1 Attach the wall mount kit to the back of the device using the three DIN rail screw holes 2 Use the device with wall mount plates attached as a guide to mark the correct locations of the four screws 3 Insert screws through the round screw holes the red arrow as below on the sides or through the key hole shaped aperture the green arrow as below in the middle of the plate and fasten the screw to the wall with a screwdriver 4 If the screw goes through the key hole shaped aperture slide the device down before tightening the screw ORing Industrial Networking Corp 7 ORing IDS M311 Series User Manual Pi EI
14. l operation modes Service Mode Service Made JF Server Port Max Connection serial Addition ait Connection Timeout Service Mode ORing Industrial Networking Corp 16 Forti RTL Slave Mode T Diz 10 lws2 Connection 100 1410000 msec 10 110000 seconds Choose an operation mode for the serial port You can configure a serial port as Modbus Master or Modbus Slave mode Available options include RTU Slave Mode RTU Master Mode ASCII Slave Mode and ASCII Master Mode RTU Slave Mode Modbus TCP masters will control Modbus RTU IDS M311 Series User Manual Slaves RTU Master Mode Modbus RTU masters will control Modbus TCP slaves ASCII Slave Mode Modbus TCP master will control Modbus ASCII Slaves ASCII Master Mode Modbus RTU masters will control Modbus TCP slaves TCP Server Port Enter the TCP server port number The maximum number of simultaneous connections supported Max Connection The maximum is 32 Connection Timeout Set a value for connection timeout The unit is in seconds 5 3 System Tools This link allows you to set up system parameters including system time and authentication data 5 3 1 SNTP Configuration SNTP Simple Network Time Protocol is a protocol able to synchronize the time on your system to the clock on the Internet It will synchronize your computer system time with a server that has already been synchronized by a source such as a radio satellite receiver or modem SNTP Confi
15. odbus RTU ASGCII Internet communication PPPoE Update DNS hostname DDNS Event warning by Syslog Email SNMP trap and beeper Configurable by Web Interface Various Windows O S supported Windows NT 2000 XP 2003 VISTA 32 64bit Windows 7 32 64bit 3 Hardware Specifications Dual DC power inputs 1xRS 232 422 485 software selectable serial port DIN rail and Wall mount enabled Redundant DC power inputs Operating Temperature 10 to 600C Storage Temperature 40 to 850C Operating Humidity 5 to 95 non condensing Casing IP 30 Dimensions 72 W x 29 4 D x 123 4 H mm 2 83x1 16x4 86 inch Hardware Overview 2 1 Top Panel 2 1 1 Ports and Connectors The device provides the following ports on the top panel The Ethernet port on the device use RJ 45 connectors Port Description Copper port 1 x 10 100Base T X port 1 three pin dual power connector DC12 48V 8 E A ee 1 Terminal block PWR1 12 48V DC 2 Power jack PWR2 12 48V DC 3 RJ45 Ethernet Connector 2 2 Front Panel PWR1 PWR2 ETH LNK ACT TXIRX 1 LED for PWR1 LED for PWR2 LED for 10 100Base T X Ethernet port LED for serial port PS QU N gt e WwW N ORing Industrial Networking Corp 4 ORing IDS M311 Series User Manual 2 2 1 LED mg is kisas ETH kasti keh LNK AGT AAA TX RX 2 3 Bottom Panel Serial Port 1 Serial port 2 Reset button ORing Industrial Networking Corp 5 Hardware Installat
16. s you to set up login account and password You can also change your password in this page User Authentication Login Name admin ld Password Mew Password Confirm New Password Enter a user name for login Old Password Enter the existing password that is used to log in New Password Enter a new password that will be used to log in Confirm New Password Retype the new password to confirm 5 3 3 Load Default You can reset the system to its factory settings Simply click on Reset which will bring you to the Reboot button Once the device is restarted it will be restore to factory default settings Factory Default Reset to default configuration Click Reset button to reset all configurations to the default value Reset ORing Industrial Networking Corp 19 ORing IDS M311 Series User Manual Please click Reboot button to restart device Reboot 5 3 4 Save Restore Config You can save current values from the device as a backup file or restore the device to previous settings by downloading a configuration file Simply browse to the configuration file you want to use and click Restore Restore Configuration You can restore the previous saved configuration to Device Server File to restore MEE SAE EH Backup Configuration You can save current EEPROM value from the Device Server as a backup file of configuration Backup Click to restore the configurations Click to back up the configurations 5
17. t a 9 041 CAE re A 9 ADDICION E 12 VIAN AGG MIG NG E 13 5 1 Network Configuration ccccccccccsecccseeeeaeeeseeeeseueeseeeeseueeseeceseueeseueeseueeseneesaes 14 SAL n Ee ln e IUO D 14 5 2 Font Sela RE din Te gcse closes ease viivat ak a ma ajana 15 SAR OMIA COMMU O DE 15 5 22 Service dee 16 5 3 System Tools vana nnan annan annan annan nna enn nan annan nne 17 5 3 1 GNTRCGontguraton nene nnnennnne naene annan 17 OS IN m a enonieaeticanenatonadonaeseon 19 545 E De 218 E 19 534 Save Restore Config ernuvonuevannenannenannanannne REENEN annan RER 20 So ALE lee 20 e MN ung e 21 ORing Industrial Networking Corp 2 Getting Started 1 1 About IDS M311 IDS M311 is a 1 port Modbus gateway which converts signals between Modbus TCP and Modbus RTU ASCII devices The device is able to support up to 31 RTU ASCIl devices with its serial port thus can effectively connect a high density ot Modbus nodes to the same network You can use the Web configuration interface to configure multiple devices and set up IDS M311 operation modes for different application reguirements IDS M311 supports RS 232 422 485 and provides dual redundant power inputs guarantee a non stop operation 1 2 Software Features ORing Industrial Networking Corp 3 Operation modes includes RTU Master RTU Slave ASCII Master ASCII Slave Supports up to 16 TCP connections and 32 reguests simultaneously Convert between Modbus TCP and M
Download Pdf Manuals
Related Search