coM.s.a.t. SMS Server
Contents
1. John and Henry will both get a SMS on their mobile phones with the text in the text field Where to send the SMS Put the phone number of the recipient in the subject line If you want to send the same SMS to several recipients separate their numbers by a comma or a semicolon date page file 04 05 2004 2 Manual SMS Server 1 2 doc coM satSMS Server You can add comments everywhere in the subject line just put them in round brackets and You can use this to recognize the recipient of the SMS without having to memorize the number You can also add a comment after the numbers separated by a colon This is for your convenience since the comments appear in the overview table of your mailbox They will not be sent Note When you send often SMS to a certain person or a group of persons you should create an entry or a list respectively in the recipients directory Please refer to the respectve section What to send Write the text of the SMS in the text field of the mail It is best to write them in text format but you can also use HTML format or MIME if allowed in the SMS Server settings How long may my mail be The normal restriction for a SMS is 160 characters If the text of your mail is longer than this it is send in several parts The SMS Server supports up to 9 parts This may be restricted by the SMS Server settings If your mail is too long it will either be cropped cut a2. The mail is sent over GSM channel 15 20 minutes later a SMS is received at channel 15 from 01759876543 This SMS will be sent to judy comsat de Postmaster address postmaster comsat de The postmaster will get all SMS that do not have an explicit address and that can not be identified as an answer to a previously sent SMS Send status failure reports to Postmaster IV Original sender Send delivery reports to Il Postmaster IV Original sender The coM sat SMS Server checks periodically for mails in it s mailbox at the mail server specified on the Mail page You can specify here how often this should happen A very short time will give some communication overhead and some POP3 servers do not allow to check for new mails too often When the time is too long the answers to request command mails will de delayed so the user may get annoyed date page file 04 05 2004 9 Manual SMS Server 1 2 doc coM satSMS Server The SMS server accepts mails in plain text HTML or MIME but you can restrict it to plain text only In this case an error mail is sent when the mail was in HTML or MIME format When a mail comes in that is too long to be sent as only one SMS you can select what should be the maximum count of parts to generate from this mail and whether mails that are longer than the resulting allowed length will be rejected with a failure report or cropped cut to the maximum The smart handling of received SMS as
3. No interworking available 212 SIM Application Toolkit Busy 0100 0101b No interworking available 213 SIM data download error 0100 0101b No interworking available 255 Unspecified error cause 0100 0101b No interworking available 300 ME failure 0100 0101b No interworking available 301 SMS service of ME reserved 0100 0101b No interworking available 302 C Operation not allowed 0100 0100b QoS not available 303 C Operation not supported 0100 0100b QoS not available 304 C Invalid PDU mode parameter 0100 0000b Remote procedure error 305 C Invalid text mode parameter 0100 0000b Remote procedure error 310 C SIM not inserted 0100 0101b No interworking available 311 C SIM PIN required 0100 0101b No interworking available date page file 04 05 2004 18 Manual SMS Server 1 2 doc coM sat SMS Server 312 C PH SIM PIN required 0100 0101b No interworking available 313 SIM failure 0100 0101b No interworking available 314 SIM busy 0100 0101b No interworking available 315 C SIM wrong 0100 0101b No interworking available 316 C SIM PUK required 0100 0101b No interworking available 317 C SIM PIN2 required 0100 0101b No interworking available 318 C SIM PUK2 required 0100 0101b No interworking available 320 Memory failure 0100 0101b No interworking available 321 Invalid memory index 0100 0101b No interworking available 322 Memory full 0100 0101b No interworking avai
4. 16 Replacement for Should always be set to 42 In the Channel Parameters Channel usage must be set to Use Channel SMS Service Center Select from the list or enter manually SMS Handling Must be set to Handle SMS for all channels that should be able to sent or receive SMS In the Routing Table Since the SMS Server uses the routing table to select a GSM channel make sure that all possible Destination Prefixes are in a destination prefix group Otherwise a failure notice will be generated SMS could not be routed check destination prefix table Start the SMS Server To start the SMS Server the Multichannel PRA must be connected Select Run SMS server from the menu SMS or click to the appropriate button in the toolbar A informational mail is send to the postmaster on start and stop o the SMS Server Note Starting the SMS Server will also start the automatic load SMS function Be sure to not manually switch of this function date page file 04 05 2004 13 Manual SMS Server 1 2 doc coM satSMS Server AT Interface Beside the possibility of using the PRAC application to send receive SMS the Multichannel PRA also provides an AT interface to enable the user to create own SMS applications or to adopt existing software The AT interface of the Multichannel PRA emulates a modem according to part of GSM07 05 Only the text mode is supported no PDU mode You can
5. a reply to a previously sent SMS may lead to errors when many users send SMS to the same recipient and only a few channels can be used For this you can switch off this feature Note If the smart reply handling is switched off only explicit addressing can be used to send a SMS from a mobile phone to an arbitrary mail address All other SMS will go to the postmaster Define a postmaster address as a default for incoming SMS that can not be assigned to another e mail address e g postmaster mycompany com You can select whether status failure reports or delivery reports should go to the original sender of the e mail to the postmaster or to both Mail settings SMS Server Settings x General Mail Localization Authentication Standard e mail address Usemame smsserver comsat de fe g sms comsat de Password if necessary You have to provide a mailbox on the mail server for this address The mailbox will be checked periodically for new mails To send a SMS write an e mail to this address with the recipients number s in the subject and the message in the mail body Server settings POP3 e g pop server com 192 192 192 50 Port def 110 110 SMTP e g smtp server com 192 192 192 50 Port def 25 25 These settings concern the mail interface of the SMS server to your mail server The coMsaxz SMS Server checks periodically for mails in it s mailbox at the mail server You have to create the mailbox on
6. for sending receiving and deleting SMS and replies with standard error codes in case of internal failures like memory overflow e Incase no internal error occurs an immediate success message is given simulating a successful delivery to an virtual SMS service center e Only now the Multichannel PRA tries to send the SMS using one of the GSM channels given by the routing tables All further error and success messages are now given by status messages as if coming from a SMS service center Please refer to GSM 07 05 for the format of these messages e Incase of errors originating from the transfer of the SMS from the GSM modem to the real service center the resulting error code is translated to a mot likely TP ST value see Translation table CSM Error to TP Status date page file 04 05 2004 14 Manual SMS Server 1 2 doc coM satSMS Server Configuration A PC is connected to the Multichannel PRA by means of a serial connection to the V24 CFG port of the Multichannel PRA The user s SMS software is running on the PC assuming a GSM modem is connected to the serial port Note Since the PRA application uses the V24 CFG port too you can not use the SMS software during configuration or servicing Initialization To send a SM the software first tries to initialize the modem by sending AT commands for example to define the SMS Service Center The coM s a t Multichannel PRA accepts the commands and generates answers in a
7. that indicate such permanent errors are marked in the translation table o In case of problems concerning the specific channel the next channel is tried All available channels are tried until sending is successful Ifno more channels are available for the prefix of the destination number and or all channels have a problem which makes it impossible to send the SM these errors are marked in the table with C a status report is generated with TP ST 01000101 No interworking available and stored in the incoming SMS buffer or sent directly unsolicited to the client referencing the internal handle of the SM Receiving Deleting SMs Incoming SMs and status messages are stored in the incoming SMS buffer also getting an internal handle A list of all received SMS can be shown with the command AT CMGL ALL To only show the unread SMS or the already read SMS use the commands AT CMGL REC UNREAD AT CMGL REC READ respectively To read a specific SMS use the command AT CMGR lt handle gt using the respective handle of the SMS to read To delete a specific SMS use the command AT CMGD lt handle gt using the respective handle of the SMS to delete date page file 04 05 2004 16 Manual SMS Server 1 2 doc coM satSMS Server Status reports On receiving a status report from the SMS service center the coM s a t Multichannel PRA translates the handle to an internal handle The status report is then stored or se
8. the mail server Then enter the mail address user name and domain in the respective fields and the password if necessary Specify the address of the POP3 and SMTP servers to use and also the ports In case of doubt use port 110 for POP3 and 25 for SMTP date page file 04 05 2004 10 Manual SMS Server 1 2 doc coM satSMS Server Note It is possible to connect the SMS server to more mail addresses to reference recipient list files Refer to the respective section for details Localization SMS Server Settings x General Mail Localization Authentication Template folder for status and failure reports in national language P coM sat Multichannel_PRA Software PRAC PRACTIZPWO92 Templates de 9 The templates in this folder are used to generate mails with status and failure reports in the national language of the user The templates can be edited and translated to fit the users needs Country code 49 Germany v National trunk prefix jo These settings guarantee the generation of the correct numbers independently of the format the user International trunk prefix joo enters the numbers Example If the Country Code is set to 49 Germany then 01701234567 will become 491 701234567 and 0097187654321 will become 97187654321 Cancel Anytime the SMS server sends a mail to an user it will reference a template file You can edit the files to fit special needs or translate them to give the users the r
9. to a list name you send just send a mail to the SMS server with the subject lt name gt The server will send back a mail with the number s Deleting an entry in the recipient directory To delete an entry or a list in the directory just send a mail to the SMS server with the subject lt name gt and an empty text field All entries assigned to that name will then be deleted Example To delete the list Eagles write a mail that looks like date page file 04 05 2004 6 Manual SMS Server 1 2 doc coM satSMS Server v To E3 smsserver comsat de Subject Eagles Text field is empty Changing recipient lists To delete only a few items of a list or to change the list by editing or adding numbers you have to send the complete list again Do this by requesting the numbers of the list Then copy the number list in a new mail edit it according to the changes to be made and send it Handling big recipient lists If the recipient lists are really big or do often change it is also possible to reference files This is done by making an assignment from a special e mail address to the respective file You can write then for example To E advertising comsat de Adv for comsat al Subject coM s a t AG can enhance your communication possibilities in a convenient and powerful way For details look at www comsat de Special address for the recipient list See the Administrator s Manual for detai
10. to use is given by the configuration parameter SMS handle blocks with each block having 256 handles The default block number is 16 giving 4096 possible handles 0 4095 After exceeding the maximum number numbering restarts at 0 Error Handling Tf all available internal handles are already used for pending SMs the coM s a t Multichannel PRA rejects the SM with CMS Error 322 Memory Full date page file 04 05 2004 15 Manual SMS Server 1 2 doc coM satSMS Server The coM s a t Multichannel PRA waits until a channel related to this provider is free for sending SMs and sends the SM The returned handle is stored together with the channel number in a handle translation table giving the relation to the internal handles Error Handling e In case no channel becomes free and the time the SM is pending exceeds the maximum time given by the respective parameter SMS life time a status report with TP ST 01000110 SM Validity Period Expired is generated e In case of a sending error the CMS error code is checked whether there is a problem only with this channel or a general problem In case of errors that are not specific to the used channel and so will make it most likely that also other channels will have the same problem a negative status report is generated and no more attempts are made to send the SM The CMS Error is translated to the TP ST according to the translation table in the appendix The CMS Errors
11. use the standard modem commands AT CMGS AT CMGR and so on like using a standard GSM modem The drawback of using a standard modem is the poor throughput which results from the time between the send command and the acknowledge from the SMS service center of approximately 5 10 seconds With means of the coM s a t Multichannel PRA it is possible to overcome this problem creating a high throughput SMS server with routing functionality Following are the highlights of the modem emulation Accept all common AT commands of GSM modems and provide a sensible answer in case of unknown command OK even when the command is not processed internally Accept the standard GSM commands to handle SMs according to GSM 07 05 like CMGS CMGR CMGD and react in a way compatible to the standard Sending of SMs parallel to voice calls Buffering of incoming outgoing SMs Routing of SMs according to the standard routing table Handling and generation of status messages Take a parameter to determine whether SM numbering should respect the standard range 0 255 or use a different range giving the highest valid number Take a parameter to determine how long the coM s a t Multichannel PRA should try to send the SM before it generates an error message that the SM could not be delivered Validity Period Principle The Multichannel PRA acts like a mixture of GSM modem and SMS service center e lt accepts the standard AT commands
12. If you allowed a whole domain in the white list you can restrict it here Enter one address per line Example babbler mycompany com gossip mycompany com Cancel There are two lists in the coM sat SMS Server settings by which the administrator can restrict use of the SMS Server to a closed group of authorized persons In the Allowed list you can enter either complete domains e g comsat de or full e mail addresses e g homeoffice gmx de When you entered a domain name you may want to exclude some addresses of this domain This can be done by the Forbidden list Only full e mail addresses are allowed in this list The Allowed list and the Forbidden lists are saved in two text files SMSAUTH TXT and SMSFORBID TXT respectively You can edit these files instead typing the addresses into the list fields Attention Please be sure to end the PRAC application before editing the files directly date page file 04 05 2004 12 Manual SMS Server 1 2 doc coM satSMS Server Configuration Parameter Settings There are some parameters in the configuration of the Multichannel PRA that influences the work of the coM s at SMS Server In the General Parameters in the section SMS SMS Life Time Set the Validity Period after which a SMS shall be deleted if sending was not successful due to temporary problems SMS Handle Blocks Only for use with the AT Interface set to default
13. John 016090122353 Henry Meeting Lunch This can be switched on off in the SMS Server settings In case an error occurred while trying to deliver the SMS an failure report is generated by the coM sat SMS Server i Failed 016090122319 John 016090122353 Henry Meeting Lunch Failure reports can be due to many reasons The recipient may no be obtainable the SIM card of the mobile phone may be full there may be a problem in the net of the SMS service provider and so on Some problems are temporarily and further attempts are made to deliver the SMS until it s validity period times out Only then or when a permanent error occurs the failure notice is delivered The exact problem is noticed in the text of the mail for example Error message from coM s a t SMS Server A SMS from Stephan Lentz lt s lentz comsat de gt could not be delivered to 4917990122352 The following status report was received SMS could not be routed check destination prefix table Original mail Hi Al please notice that the meeting starts not at 13 00 but at 14 00 today Stephan Delivery notes and failure reports may also be sent to the postmaster according to the SMS Server settings date page file 04 05 2004 4 Manual SMS Server 1 2 doc coM satSMS Server Validity Period When a SMS is being send and can not be delivered to the recipients mobile phone it will expire after a while It then will b
14. coM satSMS Server coM sat SMS Server User s Manual Administrator s Manual AT Interface date page file 04 05 2004 1 Manual SMS Server 1 2 doc coM sat SMS Server User s Manual The coM sat SMS Server is a fast and comfortable interface between e mail and SMS You can send receive and file your SMS right from your mail program You can send SMS to a list of recipients with one mail You will get delivery reports or error reports by mail Answers from the recipient of a SMS will come right back to your mail account SMS from a mobile phone can be explicitly addressed to reach a certain mail address It works with the coM sat ISDN Plus Basic Rate 2 GSM channels as well as the coMsat Multichannel PRA Primary Rate up to 64 GSM channels Sending SMS from an e mail program To send a SMS from your mail program just write an e mail to the mail address of the coMsat SMS Server It does not matter what kind of mail program you use Example A SMS shall be sent to 2 recipients 2 File Edit View Options Tools Window Help 5 2 0 Address Attach Security 3 Send T2 From Stephan Lentz lt s lentz comsat de gt To E smsserver Dcomsat de i Subject 016090122319 John 016990122352 Henry Meeting Lunch Hi John Henry please notice that the meeting starts not at 13 00 but at 14 00 today Should we take lunch together before the meeting Stephan
15. compatible destination 21 C Short massage transfer rejected 0110 0011b Service rejected 27 Destination out of service 0110 0011b Service rejected 28 P Unidentified subscriber 0100 0001b Incompatible destination 29 C Facility rejected 0110 0011b Service rejected 30 P_ Unknown subscriber 0100 0001b Incompatible destination 38 Network out of order 0100 0101b No interworking available 41 Temporary failure 0100 0101b No interworking available 42 Congestion 0110 0000b Congestion 47 Recourses unavailable unspecified 0100 0101b No interworking available 50 C Requested facility not subscribed 0100 0100b QoS not available 69 C Requested facility not implemented 0100 0100b QoS not available 81 Invalid short message transfer reference value 0100 1001b SM does not exist 95 P Invalid message unspecified 0100 0000b Remote procedure error 96 C Invalid mandatory information 0100 0000b Remote procedure error 97 P Message type non existent or not implemented 0100 0100b QoS not available 98 P Message not compatible with short message protocol 0100 0000b Remote procedure error date page file 04 05 2004 17 Manual SMS Server 1 2 doc coM sat SMS Server 99 C Information element non existent or not implemented 0100 0000b Remote procedure error 111 Protocol error unspecified 0100 0000b Remote procedure error 127 Interworking unspecified 0100 0101b No interworking available 128 Tele
16. e deleted The sender will get a failure report Error message from coM s a t SMS Server A SMS from Stephan Lentz lt s lentz comsat de gt could not be delivered to 4917512345678 The following status report was received Failed Validity period expired 04 01 30 10 58 30 Original mail Hi June this is a test only Stephan The length of the validity period is set in the configuration of the Multichannel PRA or in the SMS Server settings for the ISDN Plus Recipient directory The coMsat SMS server holds a directory of recipients consisting of assignments from names to one or more numbers Utilizing this directory you can give a recipients name instead of the number of the mobile phone It is also possible to do a kind of SMS broadcasting by defining a recipient list with all the numbers in it Defining an entry in the recipient directory To assign a name to a number just write a e mail to the SMS server with the subject lt name gt lt number gt Example You want to send a SMS to John Miller Phone number 017712345678 and to Jim Smith Phone number 01606645674 You do that by writing their numbers in the subject field and as a option add a comment Subject 017712345678 01606645674 Test SMS 1 If you do that often you may want to assign names to their numbers You send two mails to the SMS server First mail to define an entry in directory for Miller Subject john miller 017712345676 Seco
17. eports in their national language The templates are normally located in the folder PRAC templates en for the English templates or PRAC templates de for German templates If you want to translate the templates to your national language make a new folder and copy all templates of one of the existing folders to it Then edit the files in the new folder and give the new path in the SMS Server settings Note There are placeholders defined in the template files that will be replaced by the SMS Server with the respective information when it sends the mail The placeholders are enclosed in angle brackets like lt Number gt Attention These placeholders must not be changed when editing the file To enable the user to give the number of the recipient in several formats national or international select your country The national international trunk prefixes will be given automatically You can also enter the country code e g 49 for Germany as well as the prefixes manually date page file 04 05 2004 11 Manual SMS Server 1 2 doc coM sat SMS Server Authentication SMS Server Settings x General Mail Localization Authentication Allowed as saved in smsauth txt comsat de White list Only mails from addresses in this w thomas comsat de list are accepted lentz comsat gmx de Enter one address or domain per line Example mycompany com smith home yahoo com Forbidden as saved in smsforbid txt Black list
18. lable 330 C SMSC address unknown 0100 0101b No interworking available 331 No network service 0100 0101b No interworking available 332 Network timeout 0100 0101b No interworking available 340 NO CNMA ACK EXPECTED 0100 0101b No interworking available 500 Unknown error 0100 0101b No interworking available 512 User abort 0100 0111b SM Deleted by orig SME References GSM 03 40 GSM 07 05 GSM 07 07 date page file 04 05 2004 19 Manual SMS Server 1 2 doc
19. ls Reply Handling The coM sat SMS server holds a list of sent e mails If a SMS is received over one of the GSM channels the server refers to this list and checks whether someone has sent lately a SMS to that mobile phone s number via this GSM channel In this case the SMS is considered a reply to the respective mailbox Re Martin 491774536453 Meeting Lunch There is a timer which limits the validity of such correspondences It is set to 2 hours after a SMS was delivered Once a reply was detected the timer is set to another 10 minutes This addresses the possibility that there may be more parts of an answer to come If there is more than one entry in the list fitting the number and GSM channel and not yet timed out only the first will be taken until it times out If an incoming SMS can not be associated to a mail address it is routed to a standard address postmaster date page file 04 05 2004 7 Manual SMS Server 1 2 doc coM satSMS Server Explicit Addressing of Incoming SMS An incoming SMS can be explicitly addressed to certain e mail address When typing in the SMS on the mobile phone start with the e mail address where you want the SMS to be mailed to by the SMS server Separate the text from the address with a space blank Example someone farout com Here comes the text after the fags olleke If the recipient is in the same domain as the SMS Server you can omit the domain name The domain of
20. matic interworking not supported 0100 0101b No interworking available 129 C Short message Type 0 not supported 0100 0100b QoS not available 130 Cannot replace short message 0100 1001b SM does not exist 143 Unspecified TP PID error 0100 0000b Remote procedure error 144 C Data coding scheme alphabet not supported 0100 0100b QoS not available 145 C Message class not supported 0100 0100b QoS not available 159 Unspecified TP DCS error 0100 0000b Remote procedure error 160 Command cannot be actioned 0100 0000b Remote procedure error 161 C Command unsupported 0100 0000b Remote procedure error 175 Ic Unspecified TP Command error o1 00 0000b Remote procedure error 176 TPDU not supported 0100 0000b Remote procedure error 192 SC busy 0100 0101b No interworking available 193 No SC subscription 0100 0100b QoS not available 194 SC system failure 0100 0101b No interworking available 195 P Invalid SME address 0100 0001b Incompatible destination 196 C Destination SME barred 0100 0001b Incompatible destination 197 C SM Rejected Duplicate SM 0110 0011b Service rejected 198 TP VPF not supported 0100 0100b QoS not available 199 TP VP not supported 0100 0100b QoS not available 208 DO SIM SMS storage full 0100 0101b No interworking available 209 No SMS storage capability in SIM 0100 0101b No interworking available 210 Error in MS 0100 0101b No interworking available 211 Memory Capacity Exceeded 0100 0101b
21. nd mail to define an entry in directory for Smith Subject Zim smith 01608645674 Note 1 The names are case insensitive so miller and Miller is the same date page file 04 05 2004 5 Manual SMS Server 1 2 doc coM satSMS Server Note 2 The text fields are of no interest Note 3 You will get a confirmation by mail Now when you want to send a mail to Miller and Smith you can write Subject John Miller Jim Smith Test SMS 2 Note The comment the colon and the text after it is optionally Defining a recipient list It is also possible to connect a name to more than one number By this means you can define recipient lists To define a list write a mail to the SMS server with the subject lt name gt This is the same as assigning a name to one number but you now omit the number Instead a list of numbers follow in the text field of the mail v To BE smsserver comsat de Subject Eagles 017712345678 Miller 01606645674 Smith Note 1 You can add comments in brackets to the numbers By that if you want to change the list later on you can just copy this mail change the numbers you want and send it again Note 2 You will get a confirmation by mail Now when you want to send a mail to Miller and Smith you can just write Subject Eagles Test SMS 3 This will send a SMS to both numbers Showing the number s assigned to a name or list To show the number assigned to a name or the numbers assigned
22. nt to the PC Support of text length gt 160 Byte The coM s a t Multichannel PRA accepts messages with a text length up to 1440 Byte 9 parts with 160 byte each resulting in multiple SMS These SMS all use the same channel After successful delivery of the first part a status report is generated with the SC specific success code TP ST 00011010 meaning Part of the SMS is sent more parts to deliver After delivery of the last part of the SMS the normal success report with TP ST 00000000 is generated Translation table CSM Error to TP Status When a CMS error returned from a module during the attempt to transfer the SM results in the generation of a status report the CMS error code will be translated to a TP ST value All errors that are not in the following table will be translated to the SC specific value 01001001b No interworking available indicating that no more transfer attempts are made The CMS errors that indicate that there is a general problem and that no more attempts should be made to send the SM are marked with P permanent The CMS errors that indicate that there is a channel specific problem and that no more attempts should be made to send the SM using the respective channel are marked with C CMS P Meaning ST TP Meaning 1 P Unassigned unallocated number 0100 0001b Incompatible destination 8 C Operator determined barring 0100 0001b Incompatible destination 10 C Call barred 0100 0001b In
23. sensible way but does not store the configuration parameters except parameters concerning the way the modem should communicate with the PC unsolicited or polled All other necessary settings are dine by means of the PRA application Sending SMs The software sends the AT CMGS command according to GSM 07 05 waits for the prompt gt enters the text enters Ctrl Z and waits for the result code giving the internal handle see below The SM is stored in an internal buffer Example italic Typed by user bold Answer from Multichannel PRA AT CMGS 017712345678 gt This is a test lt CTRL Z gt CMGS 10 The SMS is accepted the internal handle is 10 Error Handling If no more SM can be stored because of buffer overflow the coM s a t Multichannel PRA rejects the SM with CMS Error 322 Memory full The coM s a t Multichannel PRA will then look up in the routing table for the provider assigned to the prefix of the destination number Error Handling If no provider can be found or all channels assigned to this provider are disabled the coM s a t Multichannel PRA rejects the SM with CMS Error 47 Resources unavailable unspecified Note Error code 3 No route to destination is not defined as CMS Error in GSM 07 05 In all other cases the coM s a t Multichannel PRA answers with CMGS lt mr gt and OK giving back an internal handle message reference lt mr gt which is increased after use The maximum handle number
24. t the end to the maximum that is allowed or it will be rejected in which case you will get a notice Too long 016090122319 Test of long mail Error message from coM s a t SMS Server Your mail is too long to be sent by SMS The current settings allow a maximum of 468 characters Please shorten your mail or contact the postmaster to change the settings of the SMS server Original mail This will be a very long mail The SMS Server is restricted to 3 parts 480 3 4 468 characters It tries first to split the mail into parts thereby calculating space for adding hints to appear at the beginning of each part in the form 1 3 Then it checks whether the maximum count of parts is exceeded In that case it can either cut the mail or rejects it with an error message The SMS Server is set to Reject in this case Everything that follows now is onl Please notice that the text of the original mail that is sent back is cut to the maximum possible count of characters So you easily see how many characters you would have to delete date page file 04 05 2004 3 Manual SMS Server 1 2 doc coM satSMS Server Attention Take care of automatically inserted signatures Company name Phone numbers etc They can blow up your mail unintentionally Delivery Notice and Failure Report You will get a delivery notice when the SMS arrived the recipient in the form Delivered 016090122319
25. the SMS Server is given in the SMS Server settings Example Ss lemeze Taig is also possible and much Shonter Instead of the sign you can also use the Note Incoming SMS with explicit addressing will always be routed according to the given address No Reply Handling will occur date page file 04 05 2004 8 Manual SMS Server 1 2 doc coM satSMS Server Administrator s Manual The coMsaxz SMS Server runs as a standard mail client on a PC The PC must be connected to the coM s a t Gateway either via serial connection RS 232 or via Ethernet The PC must have access to a POP3 SMTP mail server You must provide a mail address on the mail server that the coM s at SMS Server will use for example smsserver mycompany com You may provide more mail addresses to reference recipient list files Before running the SMS Server this address and some other settings must be entered in the SMS Server Settings dialog Menu SMS SMS Server options The dialog consists of several pages General settings SMS Server Settings x General Mail Localization Authentication Check for mails every 30 seconds IV Accept only text mails If not checked also HTML and MIME are accepted Send long mails in max 4 parts SMS if longer Cut to the max allowed length Reject the mail with error report MV Do smart reply handling Example judy icomsat de sends a mail to 01759876543
Download Pdf Manuals
Related Search