WS-BATT-CHRG User`s Manual
Contents
1. Connect the AC power cord to the rear panel of the BATTERY CHARGER see Figure 3 2 and another connector of the AC power cord to a commercial power outlet Figure 3 2 Connection of AC Power Cord 2 Next insert the DC OUT cable of the BATTERY PACK into the BATTERY connector at the lower left portion of the front panel ofthe BATTERY CHARGER See Figure 3 3 NOTE 3 At this time connect the DC OUT cable while carefully checking the polarities positive and negative Battery connector Figure 3 3 Connection of DC OUT Cable 12 Surfer Accessory 3 Connect the CHARGE CONTROL cable to the CHARGE CONTROL connector at the lower left portion of the front panel of the BATTERY CHARGER See Figs 3 4a and 3 4b NOTE 4 Insert the connector male of the cable into the CHARGE CONTROL connector female firmly CE a Figure 3 4a Connection of Figure 3 4b Completion of DC OUT Cable Cable Connection 4 Connect the CHARGE CONTROL cable to the CHARGE CONTROL connector on the side panel of the BATTERY PACK See Figs 3 5a and 3 5b NOTE 5 Insert the connector male of the cable into the CHARGE CONTROL connector female firmly Figure 3 5a Connection of Figure 3 5b Completion of CHARGE CONTROL Cable Connection Cable 13 BATTERY CHARGER User s Manual c Turning ON the POWER Switch on the BATTERY PACK Make sure that the POWER switch is turned ON If the POWER switch is OFF always tu2. Sending Back for Repairs If the instrument is inoperable send it back to LeCroy Corporation Refer to the contact address given at the end of this manual We will repair it without charge as long as it 1 under warranty When sending back the instrument explicitly describe the following product name serial number description of the trouble name post phone number of the contact person Table of Contents E Safety REGUIRCIMEMIS iae E eO loea N R 2 B Product Disposal and 6 RUP E ce 7 7 Ae pe 8 S BATTERY CHARGER i item teoria trementes 8 b CHARGE CONTROL Cable 9 G6 FROM Pane 9 a Rear ael euh 10 EH Op rating Proc dures 11 Checking the Remaining Battery Charge Level of the BATTERY DAC IS as stud abi bum MR MEE MERE EINE n ED 11 b Connecting the BATTERY PACK to the BATTERY CHARGER 12 c Turning ON the POWER Switch on the BATTERY 14 d Turning ON the POWER Switch on the BATTERY CHARGER to TM 14 Completing the Charging the BATTERY 15 f Disconnecting the DC OUT Cable and CHARGE CONTROL ST pH 15 B Protective FUNCTIONS ineunt uu palco eiue eS 16 lI SSDECINC ANIONS 17 Product Specificat
3. 1 The appearance and specifications are subject to change without prior notice 18 Surfer Accessory c Certifications EC Declaration of Conformity Meets intent of the European Council Directives 73 23 EEC for product safety and 89 336 EEC for electromagnetic compatibility This declaration is based upon compliance of the Battery Charger to the following standards EN 61326 1997 A3 2003 EMC requirements for electrical equipment for measurement control and laboratory use Emissions EN 55022 1994 1 1995 2 1997 Radiated amp Conducted Emissions Class A EN 61000 4 3 2000 Harmonic Current Emissions Immunity EN 61000 4 2 1999 Hlectrostatic discharge 4 contact discharge 8 air discharge EN 61000 4 3 2002 A1 2003 Radiated Fields 3V m 80 MHz to 1 GHz 80 amplitude modulated EN 61000 4 4 2004 Electrical Fast Transient Burst 1 on AC mains EN 61000 4 5 1995 A1 2001 Surge 1 KV differential mode 2 kV common mode EN 61000 4 6 1996 1 2001 RF Conducted Field 3 V 150 kHz to 80 MHz amplitude modulated with 1kHz sine wave EN 61000 4 11 2004 Mains Dips and Interruptions 100 interruption for full AC cycle EN 61010 1 2001 Safety requirements for electrical equipment for measurement control and laboratory use With the following limits Installation Overvoltage Category II Line voltage in equipment and to wall outlet Installation Overvoltage Category I All ma
4. OUT cable of the optional BATTERY PACK of the oscilloscope to the positive and negative terminals of this product The connector shape is so designed that the terminals cannot be 4 Surfer Accessory connected with a combination other than that shown above However if the positive and negative terminals are connected incorrectly this may cause an electric shock a fire or a malfunction e Do not connect a cable or cord such as AC cable other than that intended for operation stated in this instruction manual to the BATTERY or CHARGE CONTROL connector of this product Doing so may cause an electric shock a fire or a malfunction e Always use the proper 3 pin power cord suitable for the power voltage which is supplied with this product e If this product is not used turn OFF the POWER switch of this product hold the plug firmly and disconnect the power cord from the outlet Failure to do so may cause a malfunction an electric shock or a fire e Always operate this product within a specified AC power voltage range If the input current is excessive the internal fuse is blown up to shutdown the power At this time to recover the BATTERY CHARGER it is absolutely necessary to replace the internal fuse and make the adjustment Ask LeCroy Corporation to repair the defective BATTERY CHARGER e Keep product surfaces clean and dry CLEANING The outside of the BATTERY CHARGER hardware should be cleaned wit
5. ARGE lamp on the BATTERY CHARGER goes off and the charging is completed turn OFF the POWER switch on the BATTERY CHARGER Disconnecting the DC OUT Cable and CHARGE CONTROL Cable For details about how to connect the BATTERY PACK to the oscilloscope how to operate the oscilloscope by the DC power and how to read the remaining battery charge level indications see the instruction manual for BATTERY PACK 15 BATTERY CHARGER User s Manual B Protective Functions Protective circuits for electrical connection and temperature conditions are provided on this product Table 4 describes the protective functions and symptoms If any symptom stated in Table 4 occurs contact LeCroy Corporation Table 4 Protective Functions and Corrective Actions Protective function Description and corrective action If the output current becomes excessive for some reason the output fuse is blown up Charge output To recover the BATTERY CHARGER it is over current protection necessary to replace the output fuse and make the adjustment Contact the service department of LeCroy Corporation If the output voltage becomes excessive for some reason the output is stopped Charge output To recover the BATTERY CHARGER it is over voltage protection necessary to reset the over voltage status and make the adjustment Contact the service department of LeCroy Corporation If the BATTERY CHARGER is operated at a temperature exceeding the specified
6. DC OUT cable as shown in Figure 1 below to charge the BATTERY PACK The charge output is output from the BATTERY CHARGER to the DC OUT indicated on the label connector of the BATTERY PACK through the DC OUT cable during charging Additionally the control signal is input from the BATTERY CHARGER to the CHARGE CONTROL indicated on the label connector of the BATTERY CHARGER DC OUT cable BATTERY PACK WS BATTERY BATTERY CHARGER WS BATT CHRG BATTERY CHARGE CONTROL N Figure1 Configuration for Charging of BATTERY PACK CHARGE CONTROL CHARGE CONTROL cable BATTERY CHARGER User s Manual B Units a BATTERY CHARGER Figure 2 1 shows the outside view of this product EE 1 i nel 5 5 ide pane amp E dm zd Top panel amp Name Label T Front panel Side panel S Rubber foot 4 locations Unit mm Figure 2 1 Outside View of BATTERY CHARGER Surfer Accessory b CHARGE CONTROL Cable The CHARGE CONTROL cable is supplied with the BATTERY CHARGER and it is connected to the BATTERY PACK during charging Figure 2 2 shows the outside view of the CHARGE CONTROL cable 600 7 50 Figure 2 2 Outside View of CHARGE CONTROL Cable B Front Panel BATTERY This connector is an output part of the BATTERY connector CHARGER Connect the DC OUT cable of the BATTERY PACK to this connector for charging Note Do not connect any cable other than that of the BATTE
7. RY PACK CHARGE This terminal is an input part of the BATTERY CONTROL CHARGER Connect the CHARGE connector CONTROL cable supplied with this product to this connector for charging POWER lamp This lamp is a power indication lamp of the BATTERY CHARGER When turning ON the POWER switch on the rear this lamp is lit in green When turning OFF the POWER switch the lamp goes off CHARGE This lamp is a charge indication lamp of the lamp BATTERY CHARGER This lamp is lit in yellow during battery charging When the battery charging is stopped the lamp goes off BATTERY CHARGER User s Manual d Rear Panel c LeCroy LeCroy 0508123 UL Jus USTED ACCESSORY N DATE MODEL WS BATT CHRG 13 AU6 2005 inet m POWER 200VA max For recycling info visit OUTPUT 25 2 www lecroy com recycle der LaCoey Corp MANI IN LUPEN WEEE kabel 4 POWER POWER switch on the BATTERY CHARGER I POWER ON O POWER OFF When the POWER is turned ON the POWER lamp on the front panel 1s lit in green When the POWER 1 turned OFF the POWER lamp on the front panel goes off LINE The power cord of BATTERY CHARGER is connected to this connector Power voltage 90 to 264 Vrms Power frequency 47 to 63 Hz Name label LeCroy logo mark logo mark of CE UL standard BATTERY CHARGER model name power consumption manufacture No and manufacturer name are described on this name label WARNING WARNING ind
8. W waveSurrer Accessory LeCroy ws BATT CHRG BATTERY CHARGER User s Manual LeCroy WaveSurfer is trademark of LeCroy Corporation Windows is a registered trademark or a trademark of Microsoft Corporation in the United States and other countries BATTERY CHARGER User s Manual Foreword Thank you for purchasing LeCroys BATTERY CHARGER Before using this instrument please read this manual thoroughly to gain a good understanding of it After reading please keep the manual in a safe place This manual describes notes on use and basic usage of the BATTERY CHARGER Notes Parts of the contents of this manual may be modified without prior notice for improvements in performance and functions Reproduction or reprinting of the contents of this manual without prior permission from LeCroy is prohibited If you have questions about the BATTERY CHARGER please contact LeCroy Corporation Refer to the contact address given at the end of this manual Revision History June 2005 Ist edition Accessary Checking the Packing Content On delivery of the BATTERY CHARGER check each item If any of the items are missing or there is any damage immediately contact LeCroy or the sales office in charge Items to be present e WS BATT CHRG BATTERY CHARGER Accessories CHARGE CONTROL cable S POWEP COL T huit mmus Ebo ssp Ue BE RIS
9. ed Doing so may cause the product to malfunction corrupted Do not use in wet damp or explosive atmospheres For indoor use only The BATTERY CHARGER is intended for indoor use and should Be operated in a clean dry environment Do not operate with suspected failures Do not use BATTERY CHARGER if any part is damaged AII maintenance should be referred to qualified service personnel Before mounting this product always check the connecting procedures stated in this instruction manual For safety reasons make sure to turn off the power switch of the product before carrying out wiring of the connectors and cables Also make sure to turn off the power button before connecting to the input power source Turning on off the power switch controls the on off state of the output Always use the supplied CHARGE CONTROL cable If a cable other than the supplied CHARGE CONTROL cable this may cause an electric shock a fire or a malfunction Stop use if the BATTERY PACK is not charged fully within the normal charging times If the time required to charge the BATTERY PACK is significantly longer than the normal charging times shown in the specification section of the BATTERY PACK User s Manual this could indicate a problem with the BATTERY PACK or that the BATTERY PACK has exceeded the nominal battery life If this occurs please contact LeCroy sales or service office Connect the positive and negative terminals of the DC
10. h a soft cloth dampened with either deionized distilled water or isopropyl alcohol Allow the surface to dry completely before returning the instrument to service USE AND MAINTENANCE The BATTERY CHARGER is a high quality precision instrument To maintain accuracy mechanical shock should be avoided as well as damage to the cables through excessive bending All maintenance and component replacement should be referred to qualified personnel BATTERY CHARGER User s Manual B Product Disposal and Recycling This electronic product is subject to disposal and recycling regulations that vary by country and region Many countries prohibit the disposal of waste electronic equipment in standard waste receptacles For more information about proper disposal and recycling of your LeCroy product please visit www lecroy com recycle Surfer Accessory B Overview This product is an optional unit that is specially designed for the oscilloscope and is intended to charge the optional BATTERY PACK This instruction manual describes how to connect this product to the BATTERY PACK and how to charge the BATTERY PACK Before using this product immediately after you have purchased it thoroughly read this instruction manual to fully understand its contents B Configuration When charging the BATTERY PACK the BATTERY PACK is connected to the BATTERY CHARGER WS BATT CHRG with the CHARGE CONTROL cable supplied with the BATTERY CHARGER and
11. ication stating that only authorized service engineers are allowed to open the product cover and to carry out the repair and calibration work 10 Surfer Accessory B Operating Procedures Operate this product using the following procedures a Checking the Remaining Battery Charge Level of the BATTERY PACK 1 An indication switch used to check the remaining battery charge level is provided at the upper portion of the name label of the BATTERY PACK See Figure 3 1 Press this switch 2 Five charge LEDs are arranged on the right of the indication switch The remaining battery charge level is shown by lit or flashing LED lamps NOTE 1 For details about description of charge LED lamp indications see the section C Charge LED Lamp Indications on page 14 of the instruction manual for BATTERY PACK WS BATTERY an optional unit of the oscilloscope Indication switch Charge LED lamps Red LeCroy WS BATTERY BATTERY PACK NOM 22 2V 8 4Ah Lithium lon Battery PUSH MADE IN JAPAN Manufactured by MWATSU TEST INSTRUMENTS CORP for LeCroy Corp Figure 3 1 Remaining Charge Level Indication and Check 11 BATTERY CHARGER User s Manual b Connecting the BATTERY PACK to the BATTERY CHARGER Follow the steps below to connect the AC power cord DC OUT cable and CHARGE CONTROL cable NOTE 2 Before starting the cable connections always turn OFF the POWER switches on the BATTERY PACK and BATTERY CHARGER
12. ins isolated terminals Pollution Degree 2 Protection Class I 19 BATTERY CHARGER User s Manual UL and cUL Listed Conforms to UL 61010 1 2 Edition and CAN CSA C22 2 No 61010 1 04 20 LeCroy Corporation 700 Chestnut Ridge Road Chestnut Ridge NY 10977 6499 Tel 845 578 6020 Fax 845 578 5985 Internet www lecroy com 2004 by LeCroy Corporation All rights reserved LeCroy ActiveDSO ProBus JitterTrack WavePro WaveMaster WaveSurfer and Waverunner are registered trademarks of LeCroy Corporation Information in this publication supersedes all earlier versions Specifications subject to change without notice WaveSurfer Accessory WS BATT CHRG LeCroy
13. ions 1 of 2 17 b Product Specifications 2 of 2 18 c Cero OS aoea 19 BATTERY CHARGER User s Manual B Safety Requirements This section contains information and warnings that must be observed to keep the BATTERY CHARGER operating in a correct and safe condition You are required to follow generally accepted safety procedures in addition to the safety precautions specified in this section Safety Symbols amp Terms The following symbols amp terms may appear on the product and they alert you to important safety considerations CAUTION WARNING This symbol is used where caution is required Refer to the accompanying information or documents in order to protect against personal injury or damage to the BATTERY CHARGER This symbol warns of a potential risk of shock hazard The CAUTION sign indicates a potential hazard It calls attention to a procedure practice or condition which if not followed could possibly cause damage to equipment If a CAUTION is indicated do not proceed until its conditions are fully understood and met The WARNING sign indicates a potential hazard It calls attention to a procedure practice or condition which if not followed could possibly cause bodily injury or death If a WARNING is indicated do not proceed until its conditions are fully understood and met Surfer Access
14. operating temperature range the thermal fuse is blown up to stop the output To recover the BATTERY CHARGER it 1s necessary to replace the thermal fuse and make the adjustment Contact the service department of LeCroy Corporation Over heat protection 16 Surfer Accessory B Specifications a Product Specifications 1 of 2 Electrical specifications Output voltage Power consumption 200 VA or less 10 or more Between power input and BATTERY connector and Insulation resistance between power input and CHARGE CONTROL connector at DC500 V 2k Vac 1 min 50 60 Hz between power input and chassis Withstanding voltage Vac 1 min 50 60 Hz between power input and BATTERY connector and between power input and CHARGE CONTROL connector 1 The appearance and specifications are subject to change without prior notice 2 This product has passed the conformity inspection of the electric product safety laws 17 BATTERY CHARGER User s Manual b Product Specifications 2 of 2 Operation 5 C to 40 Temperature Storage non operating 20 C to 60 Operating Maximum relative humidity RH 80 for temperatures up to 31 C decreasing Humidity linearly to 50 RH at 40 No dew condensation Storage non operating 5 to 95 Upper limit derates to 50 RH above 40 12 192 m Outside dimensions 12 CONTROL cable
15. ory Operating Conditions Before using this product ensure that its operating environment will be maintained within these parameters Temperature 5 to 40 C Humidity Maximum relative humidity 80 for temperatures up to 31 C decreasing linearly to 50 relative humidity at 40 C Altitude Up to 2 000 m The design of the BATTERY CHARGER has been verified to conform to the applicable safety standards EN 61010 1 2001 UL 61010 1 2 Edition and CAN CSA C22 2 No 61010 1 04 per the following limits Installation Overvoltage Category II Line voltage in equipment and to wall outlet Installation Overvoltage Category I All mains isolated terminals Pollution Degree 2 Protection Class I CAUTION To avoid personal injury or damage to the BATTERY CHARGER or the BATTERY PACK connected to it review and comply with the following safety precautions e Use only as intended The BATTERY CHARGER is intended to be used only with the BATTERY PACK of LeCroy WaveSurfer series oscilloscopes Do not connect the CHARGE CONTROL cable of the BATTERY CHARGER to any device other than the BATTERY PACK Use of the BATTERY CHARGER and or the equipment it is connected to in a manner not specified by the manufacturer s may impair the protection mechanisms BATTERY CHARGER User s Manual Connect and disconnect properly Do not disconnect the CHARGE CONTROL cable and or the DC OUT cable of the BATTERY PACK while the BATTERY PACK is charg
16. rn it ON See Figure 3 6 POWER switch Figure 3 6 POWER Switch on BATTERY PACK d Turning ON the POWER Switch on the BATTERY CHARGER to Start Charging When pressing the I portion the POWER switch on the BATTERY CHARGER is turned ON On the contrary when pressing the O portion it is then turned OFF See Figure 3 7 POWER ON POWER OFF Figure 3 7 POWER Switch on BATTERY CHARGER The BATTERY CHARGER now begins to charge the BATTERY PACK The POWER lamp on the front panel is lit in green and the CHARGE lamp is lit in yellow during charging The remaining battery charge level is indicated by the charge LED lamps five LED lamps are lit in red on the BATTERY PACK 14 Surfer Accessory e f For details see the section Charge LED Lamp Indications on page 15 of the instruction manual for BATTERY PACK If the remaining battery charge level becomes 80 or more five charge LED lamps are litin red Charge the BATTERY PACK until all five LED lamps are lit in red When the charging is completed the CHARGE lamp goes off and five charge LED lamps red also go off NOTE 6 It is not necessary to set the charging conditions and charging time The reference charging time until the BATTERY PACK is fully charged is approximately 3 hrs It takes a relatively short time to charge the BATTERY PACK to a remaining battery charge level of 80 Completing the Charging of the BATTERY PACK When the CH
Download Pdf Manuals
Related Search