sigillatrici eng.pub
Contents
1. Place a polybag or film over the heating element at the desired seal location Press the handle down firmly for 1 2 seconds Indicator light will illuminate and goes out once seal time is completed Leave handle down momentarily after light goes out to allow film to cool Do not use undue pressure Inspect the seal If the seal does not appear to be fully welded and pulls apart adjust the timer knob to a higher setting If the seal appears broken and overheated or the polybag film sticks to the silicon rubber pressure pad beneath the lever adjust the timer knob to a lower setting or allow longer cooling time between seals TIMER SETTINGS The machine will seal all types of Polyethylene LDPE and Polypropylene in sheets or bag form The timer is infinitely variable in 9 settings to accommodate the various thickness and types of material being used Simply adjust timer to suit gauge of film in use until the desired seal strength is obtained Please ensure that the material is kept completely flat across the Teflon fabric to obtain maximum seal efficiency Depending on types of material used this unit will seal from two layers of 25 micron 100 gauge up to 2 x 200 micron 2 x 800 gauge MODEL HAND SEALER 2mm 2mm T FOR BEST RESULTS AND RELIABLE OPERATION Keep the Teflon fabric cover over the heating element clean and free of contamination If it is damaged replace it immediately Keep the silicon rubber Pressure Pad free2. of contamination replace if damaged or remove and use other side Allow at least one second cooling time between operations Daily operations should not exceed 1000 Your sealer is designed for long trouble free service Should a malfunction occur the following may assist you in locating the fault APPARENT POWER FAILURE Indicator light does not come on when handle is pressed CHECK THE FOLLOWING Switch at wall socket is on Plug fuse has not blown Power supply cord is not damaged INDICATOR LIGHT COMES ON BUT NO WELD CHECK THE FOLLOWING Inspect heating element for breaks Replace if necessary IMPERFECT WELD CHECK THE FOLLOWING Inspect Teflon fabric heating element cover for breaks or damage Replace if necessary Inspect silicon rubber pressure pad for damage Replace if necessary Inadequate cooling time Allow at least one second between operations Eventually certain components such as the heater element and the Teflon fabric heater cover will require replacement through normal wear and tear Inspect lower Teflon replace if worn otherwise element will short out on body of machine To replace the Teflon fabric heater cover Disconnect machine from mains supply Remove the screws that locate the retaining plates The Teflon fabric can be lifted clear and replaced by a new part and the retaining plate and screws replaced TECHNICAL DATA S 300 2 S 400 2 S 400 2T c
3. USER INSTRUCTIONS SERVICE CENTRE AUTHORISED DEALER Hand Sealer Mod 300 2 400 2 S400 2T Exploded view legend 1 Body 17 Bracket 2 Teflon tape 18 Sealing arm 3 Heating element 19 Knob 4 Teflon cloth 20 Platen holder 5 Cover 21 Platen spring 6 Transformer 22 Platen 7 Fixer for transformer 23 Platen pin 8 Heat holder 24 Silicon rubber 9 Washer 25 Sealing arm pin 10 Led 26 Switch lever 11 Resistance 27 Sealing arm spring 12 Controller 28 Power cord 13 Plate board 29 Volume knob 14 Bottom plate 30 Holder for cutter 15 Power board 31 Cutter 16 Micro switch 32 Bushing for power HAND SEALER 300 400 400 T BEFORE USE Locate the sealer on a level surface in a dry area Connect to correct voltage power supply see data plate for correct voltage Power will only be used on impulse when handle is pushed down CAUTION Do not use outdoors or in a wet or humid location If an extension lead is used ensure that it is undamaged and the plug is correctly wired When sealing all films it is most important to keep timer to the minimum Start by setting timer knob to lowest setting and test on the film then increase by small increments until a satisfactory seal is achieved Operating the sealer at too high a setting in relation to the thickness and type offilm being used or without any film at all will burn the upper Teflon and cause the heating element to fail prematurely OPERATION
4. cutter Power watt 510 700 700 Sealing temperature 150 max 150 max 150 max min 0 5 min 0 5 min 0 5 max 2 5 max 2 5 max 2 5 1 5 1 5 1 5 Sealing time Adjustable sealing time C sec sec Sealing thickness mm 0 5 0 5 0 5 Sealing length 2 x 300 400 2 x 300 400 m 455x75 h 210 555x75 h 210 555x75 h 210 open open open Sealing material PE PP LDPE PVC
Download Pdf Manuals
Related Search