Dear Users: Thank you for choosing our products. For your own
Contents
1. centerline first and then saw the hole to be square with a ribbon saw in accordance with the outline Sketch Map of Hole Pattern 16 3 Slotting Slot the face plate and latch assembly tank along the door centerline with chisel and drill in accordance with the size in Section 3 2 Slotting 4 Install latch bolt Insert the latch assembly into the prepared wooden door and fix it on the wooden door with countersunk head tapping screws KA4x18mm and ensure the flexibility of latch bolt Latch Assembly Installation 5 Install Exterior Assembly 1 Install spindle as shown in the following figure Spindle Installation 17 2 Put the wire harness on the exterior assembly through square hole as shown in figure 1 then install the exterior assembly on the door as shown in figure Wire Harness Exterior Assembly Installation 6 Install Interior Assembly Remove the battery pack cover and batteries connect the power harness on the interior assembly with the one on the exterior assembly as shown in figure then install the interior assembly on the door as shown in figure Wire Harness ER Interior Assembly Installation 7 Fix the Exterior and Interior Assemblies Firstly insert the screws into the corresponding holes as shown in the following figure Secondly tighten the2. 6 ls Co il Front view Side view Back view Side view 1 2 Product Features Unlock by Password and Mechanical key override Robust and Flexible Mechanical Structure with flexible level Anti Break in Damage Alarm Protection Vistor Friendly with Passage Mode 1 3 Scope of Application Perfect for Multi Family Apartment Condominium Housing Office Building Government Building Bank Court Hospital and Warehouse 1 4 Door Handing Indoor Indoor H ee ON d OS N N gt LU p Es Left push hand door Right push hand door Indoor Indoor L 1 J d Pi K 2 o Left pull hand door Right pull hand door Left handed door when you stand outside the door and the fixed hinges are on the left the password lock is then defined as left handed door which is further divided into left handed push door and left handed pull door Right handed door when you stand outside the door and the fixed hinges are on the right the password lock is then defined as right hand door which is further divided into right handed push door and right handed pull door 1 5 Technical Parameters wm Teel paramers ee o ee sr SE fe Note Parameters subject to change without prior notice 2 Function 2 1 Unlock Mode Unlock by Password and Mechanical keys 2 2 Passage Mode The swi
3. Dear Users Thank you for choosing our products For your own safety please read this manual carefully before using Please be advised The manuals are for your reference only Due to continuous improvements we reserve the right to amend the specifications without prior notice Contents elei re i ele CIN DE 6 L t Production DAWN Sisi said 6 Td MECA VEN sa 6 EEZ DIMENSIONAL eies aeea ee 7 12 eeler 7 1 3 SC0pe 0f APPEAR 7 1 4 Door Hangdmg conan nonoconnnnccnnn cnn nonnnnss 7 1 SJEGME PAET E 8 2 FIN a T O 9 2 VOC lee ls 9 PENN 9 2 PAIN FIC ONS NE 9 A LOW Battery VWWAlNINGS eegent it 9 2 lamper AA ien 9 3 Wrong Try amp Lockout Delay Funchon ceeesseeeeeereeeees 9 3 Operation amp Management 10 ST KEY Pad OA 10 A ae 10 NAS Oda 10 3 2 Admin Password Setting o oooocononccocnnconnnonrnncornncnrnnonranonncnnonnos 11 E ee WE USE ra 11 3 4 Delete eer 11 SEM SE eaa 12 3 60 USEF Pe MISSION add 12 3 7 Ee e tds 12 2 9 MENN RE 13 VE Go DEE 14 une ERT e e DEE 14 4 2 Hole DICEN ION aida 15 EA EEE Nsan TE O EOE 16 43T Installation EP as 16 Ao e eS rE LOCK AA A ee ee Ona 20 4 3 3 Notes for Installation e 21 5 MAINTENANCE ce a E 22 PLAS MIMS ALS EE 23 6 1 Attachment 1 Packing Studi alias 23 6 2 Attachment 2 Installation ToOlS oooooonononocacnnonananananononannnnnnoos 23 1 2 3 4 5 6 7 8 Important Note
4. after the door unlocked 4 Installation 4 1 Assembly Drawing 13 421110 Exterior Assembly 8 Door Frame Exterior Rubber Plate 9 Door Spindle 10 Interior Rubber Plate Latch Assembly 11 Interior Assembly Tapping Screw 12 Metric Screw Strike Plate 13 Metric Screw Strike Box NPRN 4 2 Hole Dimension Door Side View Door Front View Door Cross Section A A Hole Pattern Door A The center of the hole corresponds to the center line of latch assembly Door Frame 3D Graph Hole Pattern Door Frame 15 4 3 Installation 4 3 1 Installation Step 1 Determine the Centerline and Positions of Holes Draw a horizontal line at a certain height e g 100cm above the bottom of the door as the centerline of lever Align the hole of the centerline of lever with the hole drew on the door and the edge of paper template with door edge Draw the position line of the hole on both sides of the door including the outline and centerline of the hole and extend the lever centerline to the side of the door and draw the face plate and lock outlines as shown in the following figure 1 Paper Template Door Centerline of Lever Template of Holes 2 Drill Holes Drill holes from both sides of the door The drilling depth shall be about half of the door thickness to avoid cracking the door When drilling the square hole drill at the
5. at make sure the lock working normal and security 20 4 3 3 Notes for Installation 1 Before installation please check the door thickness will meet the requirement 35 80mm 2 During installation please handle the lock carefully to avoid any scratching of the surface and damage to the wire harness 3 Before the installation of exterior lock assembly please make sure the convex column at the backside with correct direction as shows below Check details The direction of the triangle shall be downward Convex Column Direction d Before fixed the Interior assembly please rotate the lever to the open position and tighten the M5 screw below the lever 5 Do not press the wire harness when fixing the assembly 21 5 Maintenance The lock face is prohibited to contact with corrosive substances so as not to damage the prevention layer of the lock face and affect the glossiness of lock face The lever is a key part of the door lock and its performance will directly influence its operation Do not hang any objects on the lever If the door were deformed the friction between bots and striking box will be enlarged and the bolt cannot extend fully Hereby the position of door striking plate should be adjusted Please according to the specific models to replace the AA batteries timely when th
6. e lock sounds low battery warning Pay attention to the positive and negative poles of batteries during replacement Please keep the mechanical keys well If the lock can t be rotated flexibly or the lock can t be kept in correct position you should invite the professionals to fill the mortise with mechanical lubricant Ensure that transmission part of the assemblies with lubricant to maintain its smoothness and extend its lifetime It is recommended to check the screw condition once one year Some graphite powder or pencil powder can be fill in the keyway regularly one year or if the keys cannot inserted or pulled out smoothly However any kind of oil is prohibited to fill in the cylinder that to prevent the ball spring be sticked 22 6 Attachments 6 1 Attachment 1 Packing List 1 Exteriorassemby 1 1 2 Interiorassembly 1 J 8 lLatohassemby 1 1 4 4 Strkebox 5 Strkeplate 1 1 4 6 Exterior Rubber plate 1 1 7 Interior Rubber plate 1 J ep AAbatteries EA rra To fix latch and strike plate e cross screw a TE 13 installation Template 1 SSS Pra Usermaual 1 y O IO Cette 1 wl Warramy card 1 gt 6 2 Attachment 2 Installation Tools Pencil Screwdriver Chisel Alloy bit 12 Alloy bit 20 Ribbon saw Power board 23
7. green Delete Success Note The Admin Password can t be deleted 11 3 5 Clear All User Step as following Input Admin Password OK beeps Do re mi and LED flashes green Press and hold 2 for 5 seconds LED light flashes red and alarm sounds Press OK beeps Do re mi and LED flashes green Clear Success Note The Admin Password still exist after clear operation Co 3 6 User Permission Admin 1 PC Add Delete User and One time Password Password Unlock the door 29 PC 01 45 Unlock the door NE UME 6 PC 50 55 Unlock one time only Password 3 7 Emergency Battery In case of battery depletion an external 9V battery 6F22 9V could be used as an emergency power supply Connect it via power interface at the bottom of the front lock body to supply power and unlock the door Note Please replace the lock battery immediately after unlocking by emergency battery Emergency Battery 12 3 8 Mechanical Key Each lock has configured 3 pieces of mechanical keys and they can unlock the door when password failed I Unlock by Mechanical Key Open the cylinder cover on the exterior level Insert the mechanical key and turn 90 degrees Turn the lever downwards to unlock the door Mechanical Key Operation Il Lock the Door by Mechanical Key Turn the mechanical key 90 degrees by opposite direction pull out the key when the door closed Note Please install back the cylinder cover
8. s The smart code lock is a kind of high tech product the installation always direct impacts on the operation and service life of the lock We strongly recommend installing the lock by professional person To install the lock after room decoration is recommended That will avoid the lock surface being damaged and influenced by the wet paint After installation and testing please clear all users information in the lock memory then register your own admin password at the first time To avoid any inconvenience caused by the flat battery please replace batteries upon the low voltage alarming If you are going for a long trip or the lock will be unused for a long time please carry the keys along with you and remove the batteries out to ensure the service life of the lock Password Capacity 36 pieces Default admin password 0012345 Please record all user information and fill in the User List for future use as below User List Enrollment Serial Password Enrollment EES Pepe P ES N al E O O al Na D gt O1 GES CIEN EIEND KJEM fet fefa ES fe fps ote fee 1 Product Introduction 1 1 Production Drawings 1 1 1 External View Keypad Exterior Assembly Exterior Lever Battery Cover Interior Assembly Interior Lever Interior Assembly 1 1 2 Dimensional 79 03 76 32 31 5
9. screws with a cross screwdriver keeping the exterior and interior 18 assemblies loose Then set up the exterior and interior assemblies keeping the exterior and interior assemblies to be symmetric the lock side shall be parallel with the door side and the lever and latch bolt can move freely After adjusting the exterior and interior assemblies please tighten the screws keeping the exterior and interior assemblies tightened Finally load the batteries and install interior battery pack cover to the interior assembly Fixing Assemblies 8 Determine the holes position for strike box and strike plate Push the door close to the door frame draw the lever centerline on the door frame and also draw the outline of striking box and striking plate with the drilling dimensions shown in on figure 3 2 RR d Lines on Door Frame 9 Drilling holes for striking box and striking plate Drilling the holes for striking box and striking plate according to the specified dimension and smooth them with a chisel Holes on Door Frame 10 Install Striking Box and Striking Plate Install striking box and striking plate on the door frame and fix them with countersunk head tapping screws KA4x18 SE LF FE E E Strike Box and Strike Plate Installation 4 3 2 Test the Lock Please test the lock according to the corresponding section 2 step by step after installation finished th
10. t with 5 is one time password It will be invalid automatically once after you use it 3 2 Admin Password Setting After lock installation please reset your own Admin Password immediately for security 1 Open battery cover and remove one battery slid the switch to ON 2 Press and hold 0 on exterior locks assembly Then reload the battery Beeps Do re mi and LED flashes green 3 Input 00 OK Beeps Do re mi and LED flashes green 4 Input new password within 10 digitals OK Beeps Do re mi and LED flashes green 5 Repeat step 4 and set finished Note The original admin password will be overwrite by new admin password 3 3 Add New User Step as following Input Admin Password OK beeps Do re mi and LED flashes green Input 0 OK beeps Do re mi and LED flashes green Input User ID OK beeps Do re mi and LED flashes green CLO Loe Input user password within 10 digit OK beeps Do re mi and LED flashes green 5 Repeat step 4 and set finished Note The User ID composed by 2 digit from 0 5 and should to follow the User List 3 4 Delete User Step as following 1 Input Admin Password OK beeps Do re mi and LED flashes green 2 Input 1 OK beeps Do re mi and LED flashes green 3 Input User ID OK beeps Do re mi and LED flashes
11. tch of the passage mode is on the interior lock body When the switch in ON the system is in passage mode the LED light flashes once every three seconds Then the lock can be unlock free with no verification required 2 3 Alarm Functions 1 Low Battery Warnings When the batteries go flat during the unlock the buzzer will give off warning beep beep Then you should replace batteries immediately 2 Tamper Alarm When the lock be tampered the buzzer will give off alarm sound of beep beep 3 Wrong Try amp Lockout Delay Function Upon inputting the wrong password consecutively 3 times the buzzer will give off alarm sound beep beep and the keypad will automatically lockout for 15 minutes 3 Operation amp Management 3 1 Keypad Operation 1 Keypad The lock with 7 keys 0 1 2 3 4 5 and OK Additional the key 0 1and 2 also working as function key after the admin password input EN Register New User Delete User 2 Clear All User 2 Password The password length available from 3 12 digitals It consists of 2 bytes User ID and a piece of Password After input the password and need to press OK to confirm User ID should be combined from 0 5 there are 36 pieces User ID in total as following 00 01 02 03 04 05 10 11 12 13 14 15 20 21 22 23 24 25 30 31 32 33 34 35 40 41 42 43 44 45 50 51 52 53 54 55 00 is the default Admin User ID The User ID star
Download Pdf Manuals
Related Search