"user manual"
Contents
1. Beampath 2 19 radiation angle 395 98 44 25 Foot candles 2 4250 1060 470 265 LUX 1 5 1 A Pos RS E gt amp 0 AY E 0 5 a 1 1 5 2 2 5 5 7 5 10 Distance m 0 83 1 67 2 51 3 35 Diameter m Colours 11 dichroic filters plus white UV filter 8 dichroic semicolours filters Colour wheel with variable rotation speed 11 Static gobos 13 static gobos plus open Strobe Strobe effect with variable speed 1 8 flashes per second Motor 4 high quality stepping motors controlled by microprocessors Electronics Intelligent control panel with 3 digit LED display allowing addressing drum declination reverse effect calibration reset of the unit and built in test sequence running Digital serial input DMX 512 4 control channels Channel 1 Drum declination Channel 2 Drum rotation Channel 3 Colour wheel Channel 4 Gobos shutter strobe Housing Easy access to lamp and main components thanks to large opening cover and the projector s modular construction Temperatures Maximum ambient temperature t 45 C Maximum housing temperature f steady state 80 C Minimum distances Min distance from flammable surfaces 0 5m Min distance to lighted object 0 8m Dimensions and weight Weight 9 5 kg 9 Maintenance and cleaning The operator has to make sure that safety relating and machine technical installations are inspected by an expert after ever2. and Signal into a 3 pin XLR plug and plug it in the DMX output of the last fixture 5 DMX PROTOCOL Declination of the drum axis 0 255 Control of the declination of the drum rotation axis proportional Rotation of the drum round its rotation axis No rotation step Forwards rotation from fast to slow proportional No rotation step Backwards rotation from slow to fast proportional Colours Open white step Turquoise step Red step Cyan step Light green step Magenta step Light blue step Yellow step Green step Pink step Blue step step step Red blue step Yellow Green step Blue purple step Forwards rainbow effect from fast to slow proportional No rotation step Backwards rainbow effect from slow to fast proportional Shutter Strobe Gobos 0 5 Closed step 6 63 Open step 64 127 Strobe effect from slow to fast max 8FPS proportional 128 132 Closed step 133 135 Reset of the fixture step 136 143 Open step 144 151 Closed step 152 159 Gobo 1 step 160 167 Gobo 2 step 168 175 Gobo 3 step 176 183 Gobo 4 step 184 191 Gobo 5 step 192 199 Gobo 6 step 200 207 Gobo 7 step 208 215 Gobo 8 step 216 223 Gobo 9 step 224 231 Gobo 10 step 232 239 Gobo 11 step 240 247 Gobo 12 step 248 255 Gobo 13 step 6 Addressing The control board on the top side ofthe DJ ROLLER 150 XT allows you to assign the DMX fixture address which is defined as the first channel from which the DJ ROLLER 150XT will respond to the controller If
3. USER MANUAL DJ ROLLER 150XT Table of contents 1 Safety INSTUCUONS concra c aas cer adan 3 2 Operating determinations Lleeeeeeeeeeeeeeeeieeeeeeeee eene nennen nnn annee nint nnne 4 3 Description of the device ainia 5 vE ETE a E E E E A 6 4 1Fitting EXchanging the lamp inisin 6 4 2 Rigging the fixture EET PED 7 4 3 ConnectontothemaNS ahs 8 4 4 DMX 512 connection connection between fixtures 8 5 DMX PROTOCOL Pm 9 ndo lo 20 pee 10 Te GONE BOJA ii AA 10 LAMA TANCUOAS deal 10 7 2 Special functions CM 11 8 Technical sp cifications aero E nao SNR IEEE E IN MEE RE Eu nanta anaitu 11 9 Maintenance and cleaning inea coco ii QU vH RH rw ER C 13 10 Appendix Changing the power supply settings 14 CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START UP 1 Safety instructions Every person involved with installation and maintenance of this device have to be qualilfied follow the instructions of this manual CAUTION Be careful with your operations With a high voltage you can suffer a dangerous
4. circuit burns electric shock burns due to ultraviolet radiation lamp explosion crash etc 3 Description of the device 00000000 ll FOI 1 Fastening screws 2 Bracket 3 Fixation screw for bracket 4 Objective 5 Drum Front panel 1 Fuseholder 2 Powercord 3 DMX input 4 DMX output Control display E gt D 11 11 1 3 Control board LJ 1 1 1 Menu button 2 Up Down buttons O O O 3 Display Menu Up Down 4 Installation 4 1Fitting Exchanging the lamp DANGER Install the lamps with the device switched off only Unplug from mains before On screws Aand B for re lamping screws X Y Screw Screw B insert the lamp open the small cover at the rear panel see the drawing by loosening the 2 Phillips screws A and B on the cover Gently pull out the lamp assembly If changing the lamp remove the old lamp from the socket Insert the lamp to the socket Do not install a lamp with a higher wattage A lamp like this generates temperatures the device is not designed for Damages caused by non observance are not subject to warranty Please follow the lamp manufacturer s notes Do not touch the glass bulb bare hands during the installation Make sure that the lamp is installed tightly into the lampholder system Reins
5. It s necessary to insert the XLR termination plug with 120 Ohm in the last lighting in the link in order to ensure proper transmission on the DMX data link 7 Control Board The control board situated on the top side of the DJ ROLLER 150XT offers several features You can simply set the lighting address run test show make a reset and also use special functions Browse through the menu by the pressing Up and Down keys the display shows step by step these messages 001 rdr tSt rES Press Menu if you wish to select one of them The functions provided are described in the following sections and the function hierarchy is shown below 7 1 Main functions DMX 512 Address settings The 001 flashes Use the Up and Up keys to select required address 001 509 and press Menu to confirm and return to the main menu Drum declination reverse This function allows you to invert the the declination of the drum rotation axis Use the Up and Down keys to select On if you wish this feature or Off if you don t wish this feature and press Menu to confirm and return to the main menu Test program This function allows you to run a special test program without an external controller which show you some possibilities of using DJ ROLLER 150XT Press the Menu key to run the test program the tSt will start to flash Reset Function Press Menu key to run reset This option enables the DJ ROLLER 150XT t
6. allast 4 Put the cover back before applying AC power 15
7. e g an appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails When rigging derigging or servicing the fixture staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time The operator has to make sure that safety relating and machine technical installations are approved by an expert after every four year in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are approved by a skilled person once a year The projector should be installed outside areas where persons may walk by or be seated Important Overhead rigging requires extensive experience including but not limited to calculating working load limits installation material being used and periodic safety inspection of all installation material and the projector If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and or damage to property The projector has to be installed out of the reach of people If the proj
8. ector shall be lowered from the ceiling or high joists professional trussing systems have to be used The projector must never be fixed swinging freely in the room Caution Projectors may cause severe injuries when crashing down If you have doubts concerning the safety of a possible installation do not install the projector Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector s weight Danger of fire When installing the device make sure there is no highly inflammable material decoration articles etc within a distance of min 0 5 m Mount the projector with the mounting bracket to your trussing system using an appropriate clamp The hole in the mounting bracket has a diameter of 10 mm For overhead use always install a safety rope that can hold at least 10 times the weight of the fixture You must only use safety ropes with screw on carabines Pull the safety rope through the hole in the mounting bracket and over the trussing system etc Insert the end in the carabine and tighten the fixation screw Adjust the desired inclination angle via the mounting bracket and fix the bracket screws tightly Connect the fixture to the mains with the power plug 4 3 Connection to the mains The earth has to be connected Connect the fixture to the mains with the enclosed power plug The occupation of the connection cables is as follows casera eus rm mense Brown Live Lig
9. electric shock when touching the wires This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation itis absolutely necessary for the user to follow the safety instructions and warning notes written in this manual Important The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device Please consider that damages caused by manual modifications to the device are not subject to warranty Never letthe power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Always plug in the power plug least The power plug has to be accessable after installing the device Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord This device falls under protection class Therefore it is essential to connect the yellow green conductor to earth The electric connection repairs and servicing must be carried out by a qualified employee Do not connect this device to a dimmer pack Do not switch the fixture on and off in short intervals as this would reduce the lam
10. ert the lamp assembly and tighten the 2 screws again Do not operate this fixture with opened housing cover Qa Remove the screws A and B for re lamping Adjust lamp position by turning screws X Y and Z Discggfpect the fixture from AC power before lamping Screw X Screw Z Screw Y 6 Lamp adjustment The lampholder is aligned at the factory Due to differences between lamps fine adjustment may improve light performance Strike the lamp and focus the light on a flat surface wall Center the hot spot the brightest part of the beam using the 3 adjustment screws X Y Z Turn one screw at a time to drag the hot spot diagonally across the projected image If you cannot detect a hot spot adjust the lamp until the light is even To reduce a hot spot pull the lamp in by turning all three screws X Y Z clockwise 1 turn at a time until the light is evenly distributed If the light is brighter around the edge than it is in the center or if light output is low the lamp is too far back in the reflector Push the lamp out by turning the screws X Y Z counterclockwise 1 turn at a time the light is bright and evenly distributed 4 2 Rigging the fixture The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment
11. ht blue Neutral Yellow Green Earth DANGER TO LIFE Before taking into operation for the first time the installation has to be approved by an expert 4 4 DMX 512 connection connection between fixtures DMX 512 The wires must not come into contact with each other otherwise the fixtures will not work at all or will not work properly Only use a stereo shielded cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Occupation of the XLR connection DMX output DMX input XLR mounting socket XLR mounting plug 1 Ground 1 Ground 2 Signal 2 Signal 3 Signal 3 Signal If you are using standard controllers you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain If you wish to connect DMX controllers with other XLR outputs you need to use adapter cables Building a serial DMX chain Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect one output with the input of the next fixture until all fixtures are connected Caution At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 Ohm resistor between Signal
12. ing derigging or servicing the fixture Always fix the fixture with an appropriate safety rope Fix the safety rope at the correct holes only Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened The lamp must never be ignited if the objective lens or any housing cover is open as discharge lamps may explose and emit a high ultraviolet radiation which may cause burns The maximum ambient temperature t 45 C must never be exceeded Otherwise the lamp is switched off and the fixture is out of operation for 5 minutes CAUTION The lens has to be replaced when it is obviously damaged so that its function is impaired e g due to cracks or deep scratches Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation CAUTION The lamp has to be replaced when it is damaged or deformed due to the heat Wait at least 15 minutes before remowing the lamp Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety reasons If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short
13. ire weekly cleaning as smoke fluid tends to building up residues reducing the light output very quickly The cooling fans should be cleaned monthly The gobos may be cleaned with a soft brush The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air jet The dichroic colour filters and the internal lenses should be cleaned monthly There are no serviceable parts inside the device except for the lamp and the fuse Maintenance and service operations are only to be carried out by authorized dealers Please refer to the instructions under Fitting Exchanging the lamp Replacing the fuse If the lamp burns out the fine wire fuse of the device might fuse too Only replace the fuse by a fuse of the same type and rating Before replacing the fuse unplug mains lead Procedure Step 1 Unscrew the fuse holder on the front panel with a fitting screwdriver from the housing anti clockwise Step 2 Remove the old fuse from the fuseholder Step 3 Install the new fuse in the fuseholder Step 4 Replace the fuseholder in the housing and fix it Should you need any spare parts please use genuine parts If the power supply cable of this device becomes damaged it has to be replaced by authorized dealers only in order to avoid hazards Should you have further questions please contact your dealer Version 1 1 13 10 Appendix Changing the power supply settings Both the transformer and the bal
14. last must be connected correctly for the local AC voltage and frequency The wrong settings can cause poor performance or demage ofthe moving head The factory settings are printed next to the power cord If you want to change the power supply settings follow the instructions 000000 xi Fastening screws Front cover UE version 1 Disconnect the fixture from AC power 2 Remove the front cover by loosening the 4 screws 3 Move the wire on the transformer connection block to the position according to the desired voltage Example Power supply settings 230V 50Hz ov 208V 230V 240V U d J 12 4 5 6 Transformer Ballast 0202099 686818 Transformer GEN Ballast 4 Put the cover back before applying AC power US version 1 Disconnect the fixture from AC power 2 Remove the front cover by loosening the 4 screws 3 Move the wire Don the transformer connection block to the position according to the desired voltage 4 Move the wire on the ballast connection block to the position according to the desired frequency voltage Example Power supply settings 120V 60Hz A P ai a NE o B T 656493 008 Oe KO Input mm am 210 00 Ph Transformer O gt 21 Transformer Ballast B
15. o index all effects functions and return to their standard positions 7 2 Special functions calibration Run a test program tSt must flashing Press and Down keys together and hold them until the display will show message C08 meaning the calibration value of the colour wheel Use Up and Down keys to adjust a new calibration value from range C00 C15 the wheel moves in microsteps so you can easilly center current colour Press Menu 1 on the display will appear message G08 meaning the calibration value of the gobo wheel Use Up and Down keys to adjust a new calibration value from range G00 G15 the wheel also moves in microsteps so you can easilly center current gobo Now press Menu in order to go back to colour calibration display shows current colour calibration value or press and hold Menu key until the display will show tSt in order to finish calibration procedure 8 Technical specifications Power supply EU version Voltage 208 230 240 V AC 50 60 Hz PUSO seiten serito T 2 5 230V US version Voltage 100 120 208 230 240 V AC 50 60 Hz FUS Erenn T 5 AQ 120V Lamps BLV HIT150nw 150W G12 or Osram HSD 150 70 G12 Optical System High reflecting aluminium coated parabolic reflector Manual focus Standard 19 beam angle
16. ps life During the initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective Do not touch the device s housing bare hands during its operation housing becomes hot For replacement use lamps and fuses of same type and rating only CAUTION EYEDAMAGES Avoid looking directly into the light source meant especially for epileptics 2 Operating determinations This device was designed for indoor use only If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature When taking the device into operation please make sure that the housing is closed firmly with all the necessary screws tightened up Never run the device without lamp Do not shake the device Avoid brute force when installing or operating the device When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of others The symbol m determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 0 8 meters Make sure that the area below the installation place is blocked when rigg
17. y four years in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are inspected by a skilled person once a year The following points have to be considered during the inspection 1 All screws used for installing the devices or parts of the device have to be tighly connected and must not be corroded 2 There must not be any deformations on housings fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts like axles eyes and others must not show any traces of wearing e g material abrading or damages and must not rotate with unbalances 4 The electric power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed DANGER TO LIFE Disconnect from mains before starting maintenance operation It is absolutely essential that the fixture is kept clean and that dust dirt and smoke fluid residues must not build up on or within the fixture Otherwise the fixture s light output will be significantly reduced Regular cleaning will not only ensure the maximum light output but will also allow the fixture to function reliably throughout its life Please use a moist lint free cloth Never use alcohol or solvents The front mirror objective lens will requ
18. you set for example the address to channel 5 the DJ ROLLER 150XT will use the channel 5 to 8 for control Please be sure that you don t have any overlapping channels in order to control each DJ ROLLER 150XT correctly and independently from any other fixture on the DMX data link If two three or more DJ ROLLER 150XT are addressed similarly they will work similarly For address setting follow this procedure 1 Switch On the DJ ROLLER 150XT and wait until the fixture reset has finished rES is flashing at the display 2 Browse through the menu by pressing the Up and Down keys until the display shows current addres 001 iu Confirm by pressing Menu key and 001 will start to flash frequently 3 Use the Up and Down keys to select the desired address 4 Confirm by pressing Menu Controlling After having addressed all DJ ROLLER 150XT you may now start operating these via your lighting controller Note After switching on the DJ ROLLER 150XT will automatically detect whether DMX 512 data are received If there are not received these data s at the DMX input the display will start to flash slowly 001 with actually set address This situation can be occurred if there is not connected the 3 PIN XLR plug cable with DMX signal from controller in the input of the DJ ROLLER 150XT the controller is switch Off or is failed the cable or connector is failed or the signal wires are swap in the input connector Note
Download Pdf Manuals
Related Search