P350 MANUAL 1.cdr
Contents
1. SS 1 2 13 X 2 50 BUTTON HEAD M jum AN ja PY lie NYLON NUT FOOT REST BOLT SETTINGS Bolt Location 4 7 4 O O O O eooo HIGH O O O 9 OC O LOW OO LEG REST BOLT SETTINGS Bolt Location O O O O INSIALLATION amp ASSEMBLY 12 Installing 24V Battery onto Lift Place FULLY charged Battery onto Control Box and lift up until the Battery engages the M ounting B racket The latch on the Battery will click when engaged properly and will be fixed tightly on top M ounting Bracket ALWAY S detach the Battery when NOT in use and WARNING place onto the Charger to ensure a FULLY operating Battery when needed 13 Connecting Control Pendant Insert Control Pendant plug into Control Box port by aligning key on plug with key way on the port This will ensure that the pins on the plug align with that if the Control Box Press firmly to ensure that the plug is fully seated within the port Also firmly press in the actuator plug to ensure that it is seated properly into its respective port2. A CAUTION Lift iSALWAY S to be operated under the direct supervision of an Able Bodied Adult 19 LIFT OPERATION EMERGENCY BUTTONS On the front of the Control Box there are two emergency buttons EMERGENCY STOP EMERGENCY UP EMERGENGY O STOP BUTTON IT DEPRESS Y TURN The Emergency U p Button is the small recessed button located next to the word EMERGENCY on the front of the Control Box To use take a pen pencil or any object with a point depress the button and hold until the lift is all the way up This will bypass the Control Pendant and raise the lift This function will only work if the Battery is sufficientiv A WARNING charged properly attached and if the Control Box is operating properly lt 2s Emergency UP Button qe EMERGENGY N EMERGENCY UP BUTTON U gt E mergency STOP Button The Emergency Stop Button is the larger red button on the front of the Control To ENABLE the Emergengy Stop button depress the button so it clicks and locks in its depressed position This will disable the lift and stop it immediately at the location in which the Emergency Button was depressed The button will rema
3. 21 Troubleshooting 22 EXPLODED VIEWS PARTS LIST riadas 23 HAWG POC ET 24 MITA Base ASSIM isir i siae aa nai SANA a bl 25 Sal ASSON rca bib f e f 26 FOOT REST ASS Miri 97 teg RESFASSOTRDM scada 28 WARRANTY INFORMATION A Ae e kiebi ni 29 INFORMATION This manual has been provided to assist you with lift installation and operation For further assistance please contact your authorized Harmar dealer or Harmar s Technical Service Department Harmar 2075 A7th SI sarasota FL 34234 Tel 800 833 0478 Tech 866 378 6648 Fax 941 308 7399 Email techioharmar com FILL IN THE FOLLOWING FIELDS TO KEEP FOR YOUR RECORDS PRODUCT INFORMATION Model Serial Number Purchase Date DEALER INSTALLER INFORMATION Company Name Contact Name Address Phone Number Fax Number Email SAFETY SUMMARY DANGER Failure to follow these Warnings Instructions and Owner s Manual may result in serious injury or death A WARNING gt WEIGHT LIMIT Limit for use is ONE 1 person weighing less than the maximum weight of 350Ib 159kg Use only for the transfer of a single user not as a hoist or crane Seat belt is to be used at all times during transfer Always make sure the area around lift is clear before operating Never operate the lift with any person s within the operating range of
4. X NS 7 4 N A ASIAN bw 7 IN 2 ES C kk Su f 7 XN A N See 1 8 l SNL M RS ud i SE 7 NL pL i Se SS Sa y A E S NI NG EN SS j 2 bM NO CSS M f 13 kol D Teu ES qu E a Barer Sa eem o AS go eee kw gt 9 Meet Q 4 n di E Pi b d l de SPA ARS N SA m d TTT Y gt La EI Z 7 27 27 j p 21 9 i k 7 el eee H a SS tii 1 i amp Se N NS Sg ie Ke 1 29 woe ong M l 2 10 1 1 A i 9 1 iy ELEM NG NS par At SR 1 it Y RB LN uer Sa 2 4 PX e L Ii 1 1 A RR a al 26 QN Y CE A 1 1 INI Y INI Sul ll 11 1 hu SO 2 m Di ld KNIS ees 1 y tali A o 2 2 dl Oo e i d ii A a P ee i D N 43 d Fo x i N N ae CUR ak X E m N gol 5 E css Le 5 Mk TA E i v e i Bae X l n N i TS 1 7 SON k E E mE le 4p EE pec rj H l yf 1 EL
5. N A M m P N 7 CS N 7 il N WA WA ye Se ee D ex md ES N P NC NI q KI Y X Z gt X 2 KAN 1 lt I N ER X 5 1 1 bc ies 7 N N 2 1 2 Dow M 2 N 2 gt TEREN p Pd AN BEN N 2 VN p L b NN EN Sy RA X NN NS mm N AN NN 0 2 2 Su gt X NS 2 Y ik KA gt NC Sl Us y N N Jy NN i N il gt XX Sa TS NN gt A o P ES p E Mc S PER 7 N N PANA 4 N HU P N hi N N N 74 P d Pd PE N QT CUTS 1 7 N P d 4 N kal N N 7 N Ei N aq LA 4 1 3 l Ne N 2 N M Bic 26 j N N LAN N p ri ET N N Ss Ru N 0m 4 lt a 4 v AS l Lc N n P p ES S 4 E 22 5s ss p 4 jj 4 g iku N Ce i A RA NM PA Moe SR 3 e NG 2 Fa N 5 2250 ii P y g 2 BN 3 SA 7 P4 7 7 WA IR 2 N gt SS of Pd A
6. Mi i 7 P 1 4 1 9 7 AS ze S PAR E i kl 1 9 p l ki ri j P d EN j l 1 8 N p d Ld APR H N 1 2 10 S So il X 7 A 4 A N Do pco N ES 1 4 Pad 20 27 A X N 9 1 Mee NU ocu Y p X 22 y N N l 21 1 ENS d Dow X 2 Sg si ASSEMBLV PARTS ASSEMBLV PARTS ITEM QTY PART NO DESCRIPTION PART NO DESCRIPTION 1 1 200 2L05 C BASE WELDED ASSEMBLY 15 1 910 2L02 A STICKER 2 1 201 2L02 C ARM 16 1 ALA99995 LABEL SERIAL NUMBER 3 1 201 2L05 C SPACER WELDED ASSEMBLY 17 2 BHCS 0 25 20 0 37 NP SS BUTTON HEAD W NYLON PATCH 1 4 20 X 0 37 SS 4 1 299 2L02 A COPPER SET SCREW LUG 18 2 5 0 50 13 0 75 NP SS BUTTON HEAD W NYLON PATCH 1 2 13 X 0 75 SS 5 1 320 2L02 A BATTERY PACK 19 2 BHCS 10 24 0 62 55 BUTTON HEAD 10 24 X 0 62 SS 6 1 321 2L02 A CONTROL BOX 20 2 NUT 0 37 16 NYLOCK SS NYLOCK NUT 3 8 16 SS 7 1 517 2L02 C ROTATION PLATE 21 2 NUT 10 24 NYLOCK SS NUT NYLOCK 10 32 SS 8 1 531 2L02 C LINK SHAFT 22 2 NUT M10 1 5 NVLOCK SS NVLOCK NUT M10 X 1 5 SS 9 1 557 2L02 A ARM PIN 23 2 SHCS 0 37 16 1 50 55 SOCKET HEAD 3 8 16 X 1 50 SS 10 1 599 2L02 A CONTROL MOUNTING BRACKET 24 1 SHCS M10 1 5 55MM SS SOCKET HEAD M10 1 5 X 55 SS 11 1 801 2L02 A ACTUATOR 25 1 SHCS M10 1
7. WALL Fig 4 Lift base parallel with pool wall Fig 6 Drill four holes Due to Local Electrical Code it maybe necessary to Bond the M ounting Base to the pools Bonding Grid with 8ga Copper Wire See Fig 2 3 for location Check your Local Electrical Code for proper Bonding 4 To determine the proper location to install the lift use Fig 3 and the Arm amp Base assembly as template M ake sure that the lift is an appropriate distance away from the pool wall and that all holes to be drilled are at least 4 away from any edge of the deck or slab DO NOT lift the assembly from the actuator Mark the four 4 hole locations of the base onto the deck being sure that the Base is parallel with the pool wall and the A rm is facing the correct direction Fig 4 5 6 Using the Hammer Drill and 5 8 M asonry Drill Bit drill the four 5 8 diameter holes 2 00 deep M ake sure the Drill is square to the deck and drill straight down Fig 6 Usethe Shop Vac to remove additional dust from holes and surrounding areas A CAUTION DO NOT drill too deep or the anchors will be too low for the supplied fasteners W hen operating equipment operator should ALWAY S wear A WARNING Personal Protective E quipment PRE INSTALLATION PAVER amp SAND REQUIREMENTS o ae ia ae DETERMINING THE LENGTH amp WIDTH OF THE RISER 1 ped cic ee POOL WALL 1 Hr is the Height of t
8. A ctuator Control Pendant Control Box gt Plugs Fully Seated Control Pendant Plug Da A ctuator Plug LiftWILL NOT operate if the Control Pendant and or the actuator plugs A WARNING arenor fully seated within their respective ports of the Control Box INSTALLATION amp ASSEMBLY PORTABILITY KIT included with P 350P This kit is designed to allow the user owner to transport the pool lift P350 when not in use to and from storage Be sure to check the contents of the package and verify that all parts and hardware are present before installing If any parts are missing contact the distributor from which the kit lift was purchased PARTS amp HARDWARE STAND HAIR PIN x2 1 2 LOCK NUT TOOL REQUIRED x4 1 2 13 X 1 00 BUTTON HEAD 1 2 WASHER x2 x4 DE VET 1 2 WASHER 8 32 1 2 BUTTON HEAD A 38 EXT WASHER x2 col PULL HANDLE E NI INSTALLATION Align all parts with respective holes and tighten all fasteners The Stand is to be installed on the same side as the seat and the W heel B racket A ssembiv amp Pull Handle on the opposing side CAUTION lt gt L
9. dielectric grease to the terminals after cleaning them This will help to prevent further corrosion Do not leave the battery on the lift when not in use Always store the battery on the charger whenever the lift is not being used MONTHLY USE If the lift is used monthly follow the same steps as above Also check the nuts and bolts to make sure they are securely fastened this is always a good idea no matter how often or infrequently the lift is used Also make sure to store the battery on the charger and not on the lift Leaving the battery on the lift for extended periods will significantly shorten the battery s life span STORED OCCASIONAL USE If the lift is not used often and is stored for an extended period of time follow all of the steps above Check for rusting at all crevice weld points and fasteners If you notice rusting spray some W D 40 on the affected area and take a 3M scotch brite pad and rub briskly Afterwards be sure to wash and rinse the lift again with soap and fresh water W hen storing the lift make sure it is in a dry area and covered DO NOT STORE in or around pool chemicals N ALWAYS clean the lift with FRESH water only NEVER use the pool or chemicaliv treated water for cleaning 21 A e Issue Lift stopped moving over the water l Procedure Push the EMERGENCY BUTTON TROUBLESHOOTING PROCEDURE THE BATTERY SHOULD BE FULLY CHARGED BEFORE TROUBLESHOOTING If the lift gets s
10. lift for the first time the 24V Battery must be fully charged The battery should be charged for a minimum of 24 hours on its first initial charge The battery can be left on the Battery Charger overnight or until it is needed for use It is recommended that the battery be fully charged before each use to ensure that the lift will function for the duration of its immediate use The battery should never stay on the lift if the lift is not being used lt 1 gt Installing 24V Battery onto Battery Charger Place Battery onto Battery Charger and rotate up until the Battery engages the M ounting B racket The latch on the Battery will click when engaged properly and will be fixed tightly on top of the Charger W hen the Charger is plugged in the ON light will illuminate GREEN When the Battery is properly mounted onto the Charger the Charge light will illuminate ORANGE Once the Battery is FULLY charged the Charge light will turn off and the Battery is ready to be used MOUNTING BATTERY CHARGER 2 Recharging 24V Battery M ounting Bracket To recharge the Battery grip the top rear of y of the B attery and squeeze the clip This will JA unlatch the Battery from the M ounting B racket The Batterv now be installed onto the 0 24V Battery Charger as described above Battery A CAUTION ALWAY S have
11. the lift including on the deck and or in the water ADULT USE ONLY When in use the lift is to be operated under the supervison of an adult Children should never operate nor play on or around the lift at any time NO JUMPING DIVING CLIMBING Do not jump or dive from or climb on the lift PINCH CRUSH HAZARD Always keep hands fingers legs and toes clear of lift arm base and other moving parts when in use Save a copy of these instructions in a safe and easily accessible place N BATTERY CHARGE Always have the battery on the charger charging when not in use NEVER leave the battery on the lift when not in use DO NOT allow excessive moisture to collect in the battery case It can affect battery and lift performance and could lead to battery failure and or the lift failing to operate DO NOT use the seat seat frame or actuator to move or reposition the lift NEVER apply direct water pressure to the electronic components A WARNING Limit for use 15 one 1 person weighing less than the maximum weight of 350LB 159KG SIGNAL WORDS DEFINITION Indicates a hazardous situation A WARNING that if not avoided could result in moderate to serious injury Indicates a hazardous situation that if not avoided could result in moderate to serious property damage PREPARATION SUGGESTED TOOLS The following is a suggested list of basic tools to have on hand during installation Harmar lift
12. 0 00 MIN LENGTH 2 00 i COPPER WIRE FROM HOLES 8 GA COPPER WIRE 6 00 4 00 MIN DEPTH MINIMUM D 625 X 2 00 DEEP x4 DRILL 10 00 TYP POOL WALL T 44 REBAR MINIMUM FROM BUTH DIRECTIUNS END OF SLAB Fig 2 Minimum Deck Requirements Fig 3 Lift Location and Hole Specifications Minimum Deck Requirement Minimum concrete slab should be at least 60 x 42 x 4 00 thick reinforced 4 rebar with a concrete strength of 3000PSI Anchors must be installed a minimum of 4 or greater from the edge of the slab Existing slab does not exhibit any signs of cracking or deterioration For proper installation into an existing deck follow these guidelines 1 To determine the proper area to install the lift follow the ADA guidelines Fig 1 2 Q gt 4 Y Verify that the pool deck meets the minimum requirements above also see Fig 2 If the deck does not meet these requirements then the deck needs to be cut and replaced with a new slab that meet these requirements The new slab needs to be reinforced with rebar and adhered with epoxy into the remaining existing deck Simpson SET epoxy 1s recommended or equivalent for installation When operating equipment operator should ALWAYS wear A WARNING Personal Protective Equipment PRE INSTALLATION Fig 5 Mark hole locations SS A N PARALLEL Y LL
13. 2 C FOOT PLATE SUPPORT 3 1 212 2L02 C HOUSING WELDMENT 4 1 416 2L02 A FOOT PLATE 5 1 567 2L02 C LOWER LEG TUBE 6 1 568 2L02 C UPPER LEG TUBE 7 2 BHCS 0_25 20 1_50 SS BUTTON HEAD 1 4 20 X 1 50 SS 8 2 BHCS 0_37 16 2_50 SS BUTTON HEAD 3 8 16 X 2 50 SS 9 1 BHCS 0_50 13 2_50 SS BUTTON HEAD 1 2 13 X 2 50 SS 10 2 NUT 0_25 20 NYLOCK NTE SS NYLOCK NUT THIN 1 4 20 SS 11 2 NUT 0 37 16 NYLOCK SS NYLOCK NUT 3 8 16 SS 12 1 NUT 0 50 13 NVLOCK NTE SS NVLOCK NUT THIN 1 2 13 SS 13 6 PHTS 10 32 0 37 SS PAN HEAD THREAD FORMING 10 32 X 0 37 SS EXPLODED VIEW PARIS LIST ASSEMBLV PARTS ITEM QTY PART NO DESCRIPTION 1 1 200 3L12 C LEG PLATE SUPPORT 2 1 212 2L02 C FOOT REST HOUSING 3 1 400 3L12 A LEG REST 4 i 410 2L02 A PLUG 1 DIA RND TUBE 5 1 500 3L12 C UPPER LEG TUBE 6 1 501 3L12 C LOWER LEG TUBE 7 1 ALA16031 FAST PIN CHAIN 8 1 BHCS 0 25 20 1 50 55 BUTTON HEAD 1 4 20 X 1 50 SS 9 i BHCS 0 50 13 2 50 55 BUTTON HEAD 1 2 13 X 2 50 SS 10 1 H106600 HOV SWA SAFETY PIN 11 1 NUT 0 25 20 NYLOCK NTE SS NVLOCK NUT THIN 1 4 20 SS 12 1 NUT 0 50 13 NYLOCK NTE SS NVLOCK NUT THIN 1 2 13 SS 13 6 PHTS 10 32 0 37 55 PAN HEAD THREAD CUTTING 10 32 X 0 37 SS 14 1 RIV 188 SS RIVET a 20 WARRANTY INFORMATION gt Harmar POOL LIFTS THREE YEAR NON TRANSFERABLE LIMITED WARRANTY Harmar warrants ONLY to the original purchaser of the pr
14. 5 130MM SS SOCKET HEAD CAP SCREW M10 1 5 X 130MM SS 12 2 ALA05010 FLANGE BEARING 2 INCH 26 4 WASH 0 37 1 00 0 05 N WASHER 0 40 ID X 1 00 OD X 0 05 WHITE NYLON 13 2 ALA15110 BRONZE FLANGE BUSHING 1 27 2 WASH 0 50 1 37 0 12 RH SS WASHER FLAT 1 2 SS 14 1 ALA21094 STICKER CAUTION SEAT ASSEMBLY AN EXPLODED VIEW PARIS LIST ASSEMBLY PARTS ITEM QTY PART NO DESCRIPTION 1 1 204 2L02 C SEAT LOWER SUPPORT 2 1 213 2L02 C BACK BRACKET 3 2 214 2L02 C ARMREST 4 2 410 2L02 A PLUG 1 DIA RND TUBE 5 2 542 2L02 C PLATE 6 1 900 2L02 A SEAT 7 2 906 2L02 A RUBBER BUMPER 8 1 911 3L02 A SEAT BELT 9 4 SPCR 0 25 0 50 0 18 N SPACER 1 4 ID X 0 18 NYLON 10 2 ALA25025FP END CAPS 11 2 BHCS 0 25 20 1 25 55 BUTTON HEAD 1 4 20 X 1 25 SS 12 6 5 0 25 20 1 50 55 BUTTON HEAD 1 4 20 X 1 50 SS 13 2 BHCS 0 25 20 2 50 55 BUTTON HEAD 1 4 20 2 50 SS 14 2 BHCS 0 31 18 1 75 55 BUTTON HEAD 5 16 18 1 75 SS 19 8 NUT 0_25 20 NYLOCK SS NYLOCK NUT 1 4 20 SS 16 2 NUT 0 31 18 NYLOCK SS NYLOCK 5 16 18 SS 17 2 WASH 0 25 0 62 0 04 RH SS WASHER FLAT 1 4 SS lt 26 EXPLODED VIEW PARIS LIST ASSEMBLV PARTS ITEM QTV PART NO DESCRIPTION 1 1 410 2L02 A PLUG 1 DIA RND TUBE 2 1 211 2L0
15. B1 037 2 6_50 3 8 DIA X 6 50 L 4 2 BHCS 0 25 20 31 50 55 BUTTON HEAD 1 4 20 X 1 50 SS 5 2 BHCS 0 25 20 2 00 55 BUTTON HEAD 1 4 20 2 00 SS 6 2 BHCS 0 37 16 2 50 SS BUTTON HEAD 3 8 16 X 2 50 SS 7 1 BHCS 0 37 24 1 00 NP SS BUTTON HEAD W NYLON PATCH 3 8 24 X 1 00 SS 8 4 HHOS 0 50 13 0 75 55 HEX HEAD 1 2 13 X 0 75 SS 9 4 NUT 0_25 20 NYLOCK SS NYLOCK NUT 1 4 20 SS 10 2 NUT 0_37 16 NYLOCK SS NYLOCK NUT 3 8 16 SS 11 1 NUT 0 50 13 NYLOCK NTE SS NYLOCK NUT THIN 1 2 13 SS 12 2 WASH 0 25 0 62 0 04 RH SS WASHER FLAT 1 4 SS 13 1 WASH 0 37 0 68 0 09 51 55 WASHER SPRING LOCK 3 8 ID SS 14 4 WASH 0 50 0 87 0 12 51 55 SPLIT LOCK WASHER 1 2 SS EXPLODED VIEW PARIS LIST d N a Pd hika A y w Er 5 V N ye Se 2 26 4 E 2 X 1 NIL l 7 id N P4 Sic A 524 y 1 y Wa T x i V 1 QUT y 5 4 24 4 N l 4 A S 5 d Y FN 2 KON i E Y ze TX Su H _ J 7 X 1 i LAS Pali ja 1 E 8 4 Pa gt p d NAN 2 N fl F ka ji 2 pl P d 5 Ne N D 4 z X Sa 4 gt EN p 1 N o 5 27 N 22 N d MS 2 27 N SR ger E A
16. Base to the pools Bonding Grid with 8ga Copper Wire See Fig 7 for location Check your Local Electrical Code for proper Bonding 4 proper location to install the lift is centered on the riser use Fig 7 and the Arm Base assembly as a template M ake sure that the lift is an appropriate distance away from the pool wall DO NOT lift the assembly from the actuator 5 Return to page 8 and follow Steps 5 amp 6 to finish preparations W hen operating equipment operator should ALWAY S wear A WARNING Personal Protective E quipment rre UNPACKING THE LIFT PACKAGE CONTENT Be sure to check the contents of the boxes against the package checklist verifying all parts are included with the lift for a proper installation If any parts are missing or damaged immediately contact the distributor from which you purchased the lift DO NOT attempt to install or use the lift with any missing or damaged parts NEVER attemptto lift the boxes from the ground A WARNING _ or on off a vehicle by yourself Serious injuries or damage to equipment may result LEG REST FOOT REST ASSEM BLY ASSEMBLY P 3505 P 350 SEAT p ASSEMBLV 77 27 MS lt lt ARM amp BASE ASSEM BLY CONTROL PENDANT MOUNTING BRACKET CHARGER INSTALLATION amp ASSEMBLY CHARGING THE BATTERY Before using the pool
17. DE INSTALLATION amp ASSEMBLY Attach Seat Support Frame The P350 has ambidextrous seating which RIGHT IN FLANGE LEFT allows the seat to be set to face either side of the pool dependant on pool installion HAND HAND and or shown to the left Once chosen grease the surfaces of the Flange B earings and the Seat Support Frame if necessarv as shown in the picture Insert the Flange B earings into the A rm and insert the Seat Support Frame into the bearings below SEAT SUPPORT FRAMES RIGHT 24 HAND n 4 lt SERT D INSERT ARM BASE ASSEMBLY 7 Link Shaft Adjustment The Link shaft should be attached and fastened on the opposite side of the Seat Support Frame If this iS not the case then simple unfasten the Link Shaft and attach it onto the otherside of the base LINK l SHAFT 8 Attach Rotation Plate Rotate the Rotation Plate forward and BASE fasten to Seat Support Frame with the v d pp 3 8 16 appropriate fasteners NYLON NUT 3 8 ROTATION NYLON PLATE nomen 1 2 13 me E J NYLON oe NUT 3 8 16 x 1 50 SOCKET HEAD 3 8 24 x 1 BUTTON HEAD W NYLON UN PATCH SPRING LOCK WASHER 14 INSTALLATION a
18. INSTALLATION amp OWNER S MANUAL lt gt Harmar Americas Lift Leader CERTIFIED f ADA Compliant P 350 P 350P P 3505 Pool Lift 350 16 159 kg Maximum Capacity READ AND FOLLOW ALL OF THE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION OR OPERATION OF THE LIFT LEAVE THIS MANUAL WITH OWNER OF LIFT TABLE OF CONTENTS INFORMATION FroducFINOMICNOM siria rindiera 2 Dealer Installer Information nee e 2 SAFETV SUMMARV COLON etarra 3 PREPARATION Suggested IDO vrai alain 4 PRE INSTALLATION ADA Guidelines USA only 5 Path of Travel SS With Foot 2 22 24 REKT KEE ERA EEA TA 6 With Leg eaaa aaa anana 7 Pool Deck Requirements lt Acceptable Existing 8 New Concrete Pad Under Paver and 10 UNPACKING THE LIFT PACKAGE CONTENT racial 11 INSTALLATION amp ASSEMBLY Charming Mie BORSI A 12 Anchors and Arm amp Base 13 Seat Support Frame Assembly and Link Shaft 14 Seat ASSSl HR Poem pad Ka 15 Foot amp Leg Rest Assembly and Adjustment 16 Battery Pack and Control 17 ETT TETTE 18 LIFT OPERATION CGO Mu a P EIN ddr 19 ape ge M erp 20 TECHNICAL Maintenance amp
19. WALL A The square and circle X symbols mark the lowest points on the lift with no load that would be nearest to the pool wall and eround during travel zw 7 E S 0 12in 7 2 PRE INSTALLATION PATH OF TRAVEL MAXIMUM DISTANCE FROM POOL WALL The square and circle WITH LEG REST SEAT LOWER SUPPORT A S L S MAXIMUM LOAD O LOWER LEG L L MAXIMUM LOAD De ELI X a N N NG j NONS SON 10 00 Em XS SN as an aid to determine A NA Y most ideal distance the FROM POOL WALL Ng 3 X pool lift is to be mounted p ke from the pool wall 17 00 V as ILLILLILLILI in WA NN E i NM DAMASGA GAASE UNS N N gt Symbols mark the lowest points on the lift with no load that would be nearest to the pool wall and ground during travel PRE INSTALLATION POOL DECK REQUIREMENTS 10 00 17 00 FRONT FACE PARALLEL WITH POOL WALL 42 00 MIN WIDTH 6
20. c material and cleaning of Harmar products This warranty relates only to defects in material and workmanship and DOES NOT cover any damages or failures resulting from other causes including but not limited to Acts of God misuse or abuse accident or negligence fire improper assembly or installation chipping or flaking of powder coating weather damages including ice and sand improper maintenance of any products or normal wear and tear from day to day use Damages induces by the improper use of chemicals is not covered by this warranty In the event that any products are altered repaired or improperly installed or improperly used by anyone without prior written approval by Harrnar all warranties will be void Harmar shall not be liable for any consequential special or incidental damages including but not limited to any damages for loss of use of pools or injuries to person or property and any claims therefore are hereby specifically disclaimed and excluded Some states do not allow the exclusion or limitation of incidental special or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which may vary from state to state The warranty is extended to and enforceable only by the original retail purchaser If any Harmar products fail during the warranty period as a result of a defect in material or workmanship covered by this warra
21. he Riser Lr is the Length of the Riser Wr is the Width of the Riser FE 11001809 i CENTER OF RISER Hr Height of Sand Thickness of Paver CENTERED Lrz Hrx2 12 42 00 Wr Wr Hr x 2 10 i MIN RISER WIDTH I e i EXAMPLE u i FROM ENDS OF KER LENGT Sand 2 00 deep and Paver 3 00 thick 2 3 5 00 I t Lr 5 00 x 2 12 22 00 i Wr 5 00 x 2 10 20 00 MA Fig 8 Calculation of Risers length and width L MIN 8 GA COPPER WIRE 6 00 MIN PAVER HEIGHT OOL WALL 22222 7 SAND HEIGHT ROTH DIRECTIONS amp Fig 7 Concrete requirements for Paver amp Sand A pp Y To determine the proper area to install the lift Fig 9 Reinforcement of concrete Follow theADA guidelines Fig 1 N Y The minimum deck requirements are similar to those on page 7 but this application requires a Riser in addition to the footing Fig 7 Remove the pavers sand from the location chosen for the lift and cut out the underlying foundation Replace with a new slab with a Riser incorporated on top of it Fig 7 Use Fig 8 to determine the correct size of the Riser The new slab needs to be reinforced with rebar and adhered with epoxy into the remaining existing deck Fig 9 Simpson SET epoxy is recommended or equivalent for installation Y Dueto Local Electrical Code it maybe necessary to Bond the M ounting
22. iftshould always be in its most up position when moved and or stored lt Thelift should never be operated when not fastened to the deck or in storage 46 tems should never be rested on the lift or seat when not in use STAND WHEEL BRACKET ASSEMBLY PULL HANDLE 18 LIFT OPERATION BEFORE OPERATING THE LIFT E gt lt Always make sure that the area around the lift is clear before operating 2 gt Never operate the lift with any person within the operating range of the lift including the deck and or water 3 DO NOT allow anyone to operate the lift without adult supervision 4 gt DO NOT allow children to play on or around the lift at any time GT gt 4 5a Check all fasteners and joints for tightness and wear before each use OPERATING THE LIFT DOWN UP To move thelift into the pool le move the lift out of the pool press and hold the DOWN press and hold the UP button button on the Control Pendant on the Control Pendant To STOP moving release To STOP moving release the button at the desired the button once the lift is at depth WW its highest point or has stopped E A CAUTION If the DOWN button is NOT released the lift will continue to a depth below the crest of the water m gi db E
23. in locked until itis released AN WARNING Thelift WILL NOT function until the E mergency Button has been released To RELEASE the Emergency Stop button and resume operation of lift simply turn the button clockwise until the it pops out 20 MAINTENANCE amp CARE The lift should be cleaned routinely to ensure the life and integrity of the lift Cleaning product is entirely up to the owner as there are many to choose from For routine cleaning it is recommended to use gentle soaps detergents or a diluted mixture of ammonia If scrubbing is required for tough stains use a soft scrub with brisk rubbing DAILY USE If the lift is used daily be sure to wash the lift at the end of each day Wash the lift with fresh water a mild soap and a soft cloth Do not use bristled brushes or steel wools to clean the lift as it will scrap off the powder coating Check that the lift is working properly and then place the battery on the charger It is recommended that the battery be charged after every use WEEKLY USE If the lift is used weekly follow the same procedure as above Also be sure to check all of the contact points terminals for damage or corrosion If you notice corrosion gently clean the terminals To clean corrosion from the terminals use a q tip and some rubbing alcohol If the corrosion is particularly stubborn try using a 3M scotch brite pad but be careful not to damage the terminals A pply
24. mm minimum from the edge of the pool wall The deck surface Between the centerline of the seat and the pool edge shall have a slope no greater than 1 48 o 1009 2 3 CLEAR DECK SPACE On the side of the seat opposite the water a clear deck space shall be provided parallel with the seat The space shall be 36 inches 915mm wide minimum and shall extend forward 48 inches 1220mm from a line located 12 inches 305mm behind the rear edge of the seat The clear deck space shall have a slope not greater thanl 48 48 00 1219 2 MINIMUM 914 4 MINIMUM CLEAR DECK SPACE REQUIRED BY ADA 12 00 304 8 MINIMUM i m 16 00 406 4 MINIMUM POOL DECK Fig 1 ADA Deck Requirement PRE INSTALLATION PATH OF TRAVEL WITH REST SEAT LOWER SUPPORT B A S L S MAXIMUM LOAD O LOWER LEG oe AME L L MAXIMUM LOAD A 1 lc i O ERIT ELAN MAN MAA ESOS 10 00 5 Path of Travel can be used MINIMUM DISTANCE E NC as an aid to determine ES a most ideal distance the g pool lift is to be mounted 17 00 id from the pool wall MAXIMUM DISTANCE Y FROM POOL
25. mp ASSEMBLY Attach Seat A ssembly Rest Seat A ssembly onto Seat Support Frame align holes and tightly fasten With respective fasteners SEAT ASSEMBLY 1 4 20 x 2 00 BUTTON HEAD bu TS NYLON NUT x4 x2 1 4 20 x 1 50 A CAUTION DO NOT unfasten or disassemble Seat from Back amp Lower Supports SUPPORT ASSEMBLY SUPPORT INSIALLATION amp ASSEMBLY 3 8 16 X 2 50 BUTTON HEAD x2 LOWER SEAT SUPPORT 3 8 16 NVLONNUT x2 FOOT REST ASSEMBLY LEG REST ASSEMBLY 11 gt Foot amp Leg Rest Adjustment The Foot Rest has two setting high and low and the L eg Rest has three settings high medium and low depending on the desired height To adjust the height of the Foot Rest remove the bolt adjust the height up or down align the holes at the desired height reinsert the bolt into the correct hole as shown and fasten gt Attach Foot amp Leg Rest Assembly Thefoot rest shown and leg rest are designed to be ambidextrous to allow for right amp left hand seating The Foot amp Leg Rest should always be on the side nearest to the water To attach the A ssembly simply align the holes on the Foot amp Leg RestA ssembly with that of the Lower Seat Support and fasten with the supplied hardware A dii
26. n no event shall Harmar s liability exceed the entire amount paid to Harmar by th original purchaser for the failed or defective product In no event shall Harmar be liable for any incidental consequential special indirect punitive or exemplary damages or lost profits from any breach of this limited warranty or otherwise THANK VOU FOR MAKING HARMAR AMERICAS LEADER IN LIFTS gt Harmar America s Lift Leader 2075 47th Street Sarasota Florida 34234 www harmar com 1 800 833 0478 902 3L05 AA 053013
27. nty the original retail purchaser is to contact the installer of the or place of purchase to assess the defect or damage Defective parts must be returned prepaid to Harmar at 2075 47th Street Sarasota Florida 34234 for inspection prior to credit repair or replacement at Harmar s option Harmar s sole obligation and the exclusive remedy under this warranty is limited to such credit repair or replacement A new warranty period shall not be established for the repaired or replaced products Such products shall remain under warranty for the remainder of the original warranty period on the original products purchased 4 D ly 4 Y 4 4 4 4 Y 4 4 4 D d l 7 4 A WARRANTY INFORMATION This written limited warranty constitutes the final complete and exclusive statement of warranty terms No person or organization is authorized to make any other specific or implied warranties or representations on behalf of Harmar The warranties set forth herein are in lieu of all other warranties expressed or implied which are hereby disclaimed and excluded including without limitation any warranty of merchantability or fitness for a particular purpose or use The sole and exclusive remedies for breach of any and all warranties with respect to the products shall be limited to repair or replacement at Harmar s designated factory location or duly appointed distributor or in place at Harmar s option I
28. oduct manufactured by Harmar assembled and installed in accordance with Harmar s assembly and installation instructions properlv used and maintained shall be free from defects in material and workmanship for a period of three 3 years from the date of original purchase with the exception of the following items Battery Pack and Seat each have a one 1 year warranty from the date of original purchose The Pool Lift has a three 3 year warranty on the frame mechanical electrical motor components excluding powder coated paint finisa which may become scratched or chipped with normal use The Battery Pack and Seat including seat frame spreader bars sling and powder coat paint finish have a one 1 year warranty Within the warranty period Harmar will repair or replace any item deemed to be found defective Normal maintenance and care of the unit including charging the battery when not in use is recommended IMPORTANT Weight capacity of pool lift seat and its seat support frame is NOT to exceed the MAXIMUM LIFTING CAPACITY of 350 Ib 159 kg The warranty is non transferable and is subject to the following terms and conditions Harmar shall not be responsible for the cost of removal or replacement of any defective Harmar product nor for any other expenses or for damages which might be incurred in such removal or replacement This warranty specifically excludes fading or staining of material rust or corrosion of any metalli
29. s are designed to install with as little assembly by the installer as possible WA HAMMER DRILL TAPE MEASURE MARKING IMPLEMENT SU Geo MASONRY DRILL BIT SOCKET SET WRENCH SET ALLEN WRENCH SPECIFICALLY SPECIFICALLY SPECIFICALLY SPECIFICALLY 7 16 7 16 1 8 ee 3 8 3 8 5 92 1 2 1 2 o 9 16 9 16 2 32 3 4 3 4 5 16 17mm 17mm 3 8 amm SAFETY HAMMER FLAT HEAD PHILLIPS HEAD GLASSES SCREWDRIVER SCREWDRIVER As always if you have any questions concerns or comments please feel free to contact Harmar s Technical Service Department at 866 378 6648 or tech harmar com PRE INSTALLATION ADA GUIDELINES usa ony Before installing the P350 Lifts it 15 necessary to select the correct location for the Mounting Base The P350 Lifts can be installed in a wide variety of locations but the owner and installer should be aware of the regulations set forth by the Americans with Disabilities Act ADA with concern to lift installations Fig 1 below shows an example of an ADA compliant installation which incorporates the following ADA rules in order to be compliant o 1009 2 1 POOL LIFT LOCATION Pool lifts must be located where the water level does not exceed 48 inches 1220mm unless the entire pool is greater than 48 deep Harmar requires a minimum pool depth of 40 e 1009 2 2 SEAT LOCATION In the raised position the centerline of the seat shall be located over The deck and 16 inches 405
30. tery Pack and Control Box If corroded or dirty clean off using rubbing alcohol Once cleaned it is recommended to add dielectric grease to the terminals to prevent corrosion and to ensure good electrical contact Reinstall the Pack onto the Control Box When properly engaged onto the M ounting Bracket the latch on the back of the Battery Pack will CLICK If lift fails to lift then try another fully charged battery If lift still fails to operate then the Control Box Will need to be replaced Contact an A utorized lift dealer for component replacement TheliftWILL NOT function if the Battery is not A CAUTION charged or if the Control Box is damaged or malfunctioning 22 EXPLODED VIEW PARIS LIST P350 ASSEMBLV ASSEMBLV PARTS ITEM QTV PART NO DESCRIPTION 1 1 210 2L02 C SEAT SUPPORT FRAME 2 1 N A ARM 8 BASE ASSEMBLY 3 1 N A SEAT ASSEMBLY 4 1 N A FOOT REST ASSEMBLY 5 1 00 2 05 HARDWARE PACK EXPLODED VIEW PARTS LIST HARDWARE PACK fi SEEE 350 OWNERS MANUAL ASSEMBLY PARTS ITEM QTY PART NO DESCRIPTION 1 4 540 2L03 A 1 2 13 DROP IN ANCHOR 2 1 902 3L05 A OWNERS MANUAL 3 1 S
31. the Battery charging on the Charger when not in use 12 INSTALLATION amp ASSEMBLY ARM amp BASE ASSEMBLY _ ON of 1 2 13 0 75 HEAD 4 x4 SPLIT LOCK WASHER x4 m ais amp BASE DROP IN ASSEMBLY ANCHOR Insert Drop In Anchors Before inserting the Drop In Anchors apply a small amount of Epoxy into the four anchor holes and to the outside of the anchors Insert the Drop In Anchors into the holes and gently tap them in being careful not to damage the thread they should sit flush with or just below the deck Once In place using the Setting Tool forcefully strike the inside of the anchors to set them 3 x4 ZN Anchor must be set flush or slightly below surface INSERT APPLV SMALL E U AMOUNT OF an EPOXY TO HOLES amp ANCHORS v SETTING TOOL Fasten Arm Base Assembly Align mounting holes with anchors and tightly fasten with spring lock washer and bolts gt 4 lt S gt GROUNDING 8 GA COPPER WIRE A CAUTION 00 NOT apply too much Epoxy A CAUTION DO NOT lift from the Actuator 5 gt Attach Copper Wire Fasten copper wire to Grounding L ug located within the B ase of the assembly CHECK LOCAL ELECTRICAL CO
32. tuck over or in the water and the Control Pendant does not raise the lift then using a pen pencil or pointed object depress the button located on the Control Box nextto the word EM ERGENCY This Will bypass the Control Pendant and raise the lift If this does not raise the lift then the remote may be fine and the problem is with either the Battery Control Box or damaged cables Issue Lift will not operate when buttons on control pendant is pressed la Procedure Check Cable Connections to Control Box 32 Procedure Check Battery Connections Check underneath the Control Box to be sure that all cables P For are properly seated within their respective ports The plugs should be recessed within those ports Verify by unplugging both the Control Pendant and the A ctuator cables Check that there is no corrosion or damage to the connectors pins Plug the Control Pendant back into the Control Box by aligning key on plug with key way on the port Press in firmly to ensure that the plug is fully seated within the port For the actuator Plugging In insert the cables jack into its port and press in firmly Check that the Battery Pack is properly secured onto the M ounting Bracket The Battery pack should be locked in place with nearly no movement if shaken Verify by unlatching from M ounting B racket Check that there is no corrosion or damage to the terminals on the Bat
Download Pdf Manuals
Related Search