User manual Mobeye i110
Contents
1. mobeue User manual Mobeye i110 SW version 6 N Table of content 1 h ee l lt amp N To get ready in four steps Step 1 SIM Gard Step 2 Place the batteries Step 3 Program the phone numbers Step 4 Check the settings Switching the motion detector on off Switching on Switching off Mobeye settings Gonfiguration User code SMS Recognition text Telephone numbers SMS on off Gall on off The Sensor sensitivity Entry delay Entry indication Siren Temperature alarm Adjusting the temperature Interval test message Advanced options Request settings Reset to factory settings Leave the menu Position of Mobeye Test GSM network strength Issue solving Technical data O O O O O O QO QO QO OONNN ODO OF 0101 01 QI Attention Very important This user manual contains important guidelines for the installation and usage of the Mobeye i110 Please read these thoroughly before you start using the Mobeye In case of damage caused by disregarding the guidelines the warranty expires The user must regularly check the proper functioning of the Mobeye The manufacturer cannot be held liable for any damage caused by any incorrect use or incorrect functioning of the Mobeye Safety guidelines The permitted ambient temperature during operation may not be exceeded not lower than 10 C and not higher than 55 C The device is intended for use in dry and clean places e Protect the de2. is switched off the siren will stop It is possible to test the loud alarm During the test the siren will be heard until it is cancelled by lt OK gt lt OK gt This test is also possible in case the Mobeye i110 is programmed as a silent alarm 3 11 TEMPERATURE ALARM The Mobeye is able to send a temperature alarm as soon as the actual temperature reaches a programmed min or max level This function can be used independently of the motion detection As soon as the temperature Is too high or too low an SMS text message is sent followed by a telephone call As long as the out of range temperature remains the report will be repeated hourly Once the temperature is back to normal the Mobeye confirms this to you This function is active as soon as a temperature limit is programmed By resetting the limits the function becomes inactive 3 12 ADJUSTING THE TEMPERATURE The built in temperature sensor may have a standard deviation of the actual temperature In this case the deviation will be similar at all temperatures It is possible to correct the temperature deviation in the Mobeye i110 In the SMS setting summary you see the reported temperature If a correction is specified it is processed in the displayed temperature the correction factor itself is displayed separately Example Mobeye temperature 13 C Actual temperature 14 C To correct this deviation one degree should be added 3 13 INTERVAL TEST MESSAGE The Mobeye can
3. send test messages Through these test reports you will be ascertained of the proper functioning of your Mobeye You can set the interval between the reports indicate the number of days between reports This is adjustable between 0 no test reported and 30 monthly test message Note the interval of 1 day will result in a daily test message the exact time between the messages will be about 24 hours The smaller the interval between the test reports the shorter is the battery life The test message only works if the system is on or a temperature limit is set 4 ADVANCED OPTIONS 4 1 REQUEST SETTINGS The settings can be sent to the set telephone number as SMS text message In this way you also check the correct working of the SIM card e Enter your 4 digit user code factory setting 1111 e Press menu e Enter 10 e Press OK Within ca 30 seconds the set phone number will receive the list with settings 4 2 RESET TO FACTORY SETTINGS It is possible to reset the Mobeye to factory settings e Enter your 4 digit user code factory setting 1111 e Press menu e Enter 99 e Press OK After several seconds a short confirmation tone is heard The user code is also reset to 1111 4 3 LEAVE THE MENU The menu can be left from any position by pressing OK twice 4 4 POSITION OF MOBEYE The built in motion sensor has a 3602 reach The Mobeye can be positioned both vertical as horizon
4. 11 e Press menu e Enter 10 e Press OK Within ca 30 seconds the set phone number will receive the list with settings 2 SWITCHING THE MOTION DETECTOR ON OFF 2 1 SWITCHING ON To activate the Mobeye motion detector with your personal user code e Enter your user code e Press OK The light turns red shortly and an indication tone is started This repetitive tone will last during the exit delay of 60 seconds As soon as the acoustic signal stops the Mobeye is active In case the user code is entered incorrectly 3 times the indicator turns red and the Mobeye will be blocked during 10 minutes 2 2 SWITCHING OFF To de activate the Mobeye motion detector with your personal user code e Enter your user code e Press OK The light switches to green and a confirmation melody is played 3 MOBEYE SETTINGS The Mobeye settings can be added via the keypad and SMS text messages First the method of programming is discussed next the explanation of the settings 3 1 CONFIGURATION To change the settings please follow the instructions e Enter your 4 digit personal code e Press menu gt light turns green e Enter the menu number see list below e Press OK e Enter the new setting e Press OK The light switches off a confirmation melody is played In case of false entries the light turns red and a short beep will sound The menu can be left from any position by t
5. Apart from that it is wise to set a recurrent test message in the menu so the card will be used at least once a month dill e Open the back cover of the Mobeye Aa e Place the SIM card in the holder For opening closing shift the cover slightly aa 1 2 STEP 2 PLACE THE BATTERIES Place the four lithium 3 0 volt batteries CR123 When replacing the batteries all settings remain unchanged After placing the SIM card and the batteries the Mobeye will perform a self test during 1 minute During the test the light is red In case the light is flashing red a problem with the SIM card is detected A reason could be no SIM card was placed or the PIN code security of the SIM card was not disabled Close the Mobeye using the 4 screws 1 3 STEP 3 PROGRAM THE PHONE NUMBERS You need to program at least one phone number in the unit This phone number is used to send the messages to e Enter your 4 digit user code factory setting 1111 e Press menu e Enter 01 01 for the 1st phone number 02 for the 2nd phone number e Press OK e Enter the phone number e g 0612345678 e Press OK The light turns green and a confirmation melody is played The Mobeye is ready to use 1 4 STEP 4 CHECK THE SETTINGS The settings can be sent to the set telephone number as SMS text message In this way you also check the correct working of the SIM card e Enter your 4 digit user code factory setting 11
6. OFF By default the Mobeye i110 sends alarm notifications via text message and call to the preset contact persons By turning off the CALL the unit will only send an SMS text message as alarm notification 3 7 THE SENSOR SENSITIVITY The detectors sensitivity can be changed to a high or low er value 1 High 2 Low In the high sensitivity mode each detection will provoke an alarm In the lower sensitivity mode the alarm will be provoked in case two detections are measured within a time frame of 15 seconds This mode prevents false alarms in case of e g draught and is most suitable in case the sensor is directed towards an open space 3 8 ENTRY DELAY It is possible to choose from 4 entry delay times The entry delay is the time between the moment of detection and the moment of sending the first SMS text message Take care in case the GSM network has a low reach the time can be longer in case the network connection was not established within the time of the entry delay 3 9 ENTRY INDICATION As factory setting there is no entry indication It is possible to hear an indication beep during the entry delay This can be used as a reminder that the Mobeye is in active mode It is also possible to let the LED indicator flash a few times just as indicator for the user 3 10 SIREN After the entry delay the siren can sound during two minutes At the same time the SMS text messages and telephone calls will be done At soon as the Mobeye
7. he ETSI GSM Phase 2 standard e Output power Class 4 2W 900 MHz Class 1 1W 1800 and 1900 MHz Temperature range 10 until 55 C Weight ca 275 gram incl batteries e Dimensions 161 x 90 x 35 mm LxWxH e Batteries 4 x CR123 Lithium 3 0 V Power 50 HA short peaks of max 2A Support For support on technical problems regarding Mobeye please contact info mobeye eu This manual is published by Mobeye All rights the translation included are reserved Any reproduction either photocopy microfilm or saved in an automated data dictionary only after written approval of the Publisher Reprinting even in summary is prohibited This user manual meets the technical requirements at the moment of printing Changes in technology and equipment are reserved Copyright 2013 by Mobeye version 1110EN131001 C Declaration of Conformity Herewith we Mobeye declare that the product Mobeye i 110 is in compliance with the essential requirements of the following European standards EU Directives Directive 73 23 EEC low voltage directive Directive IEC EN 50130 Electromagnetic compatibility Directive 1995 5 EC R amp TTE Radio amp Telecommunications Terminal Equipment The conformity with the essential requirements of 1995 5 EC has been verified against ETSI EN 301 489 1 V1 5 1 ETSI EN 301 489 7 V1 2 1 ETSI EN 301 511 V9 0 2 CENELEC EN 60950 2001 Mobeye B V Poeldonkweg 5 5216 JX s Hert
8. he strength per network This search function can take some minutes In case you want to leave the function before it is ready please press OK twice Warning In case of a weak signal the Mobeye can still be used but there is a risk that message cannot be sent or will be received with a delay In case of no reach it is advised to use a SIM card of a provider with a stronger network 5 ISSUE SOLVING Se NE Mobeye cannot be switched on You No valid Telephone number was Enter a valid number hear an error tone the red light is entered turned on shortly Check the SIM card Switch off the Mobeye The light is flashing during switching No valid SIM card was entered or the on SIM card was not made pin code free It is impossible to change the Mobeye is activated settings After entering your personal code followed by menu the error tone is played and the light turns red No GSM reach during the GSM test No network is available belonging to the SIM cards provider The light remains red You entered a false user code three times You do not receive a SMS with the Telephone number is not correct settings For other questions please refer to the site www mobeye eu Choose another network orovider Wait 10 minutes and then re enter the correct user code Re program the telephone number Change the menunr 06 to 01 6 TECHNICAL DATA e GSM Tri Band EGSM 900 1800 1900 MHz compatible to t
9. keypad only via sending an SMS text message Switch the Mobeye into the programming mode In this mode the GSM module is switched on and is able to receive messages e Enter your 4 digit personal code factory setting 1111 e Press menu e Press 21 gt light turns green e Press OK First the light flashes red interval ca 1 sec As soon as the light turns green the Mobeye is able to receive SMS messages To program the recognition text send an SMS in following structure e lt user code gt name xxxxxx Please regard the dots between and behind the commands command name in small letters Example enter the text boat evergreen e g user code 1111 e 1111 name boat evergreen You will hear two short beeps in case of a correct command Leave the menu by pressing OK twice 3 4 TELEPHONE NUMBERS The SMS alarm message and voice alarm signal message can be sent to one or two telephone number At least one telephone number must be entered in the Mobeye The test messages and low battery messages are sent to the first programmed telephone number 3 5 SMS ON OFF By default the Mobeye i110 sends alarm notifications via text message and call to the preset contact persons By turning off the SMS the unit will only call after the movement sensors sends an alarm Regardless of this setting the temperature alarm always sends an SMS including the actual temperature 3 6 CALL ON
10. n sound After an alarm the Mobeye will be in standby status for about 5 minutes Hereafter it is able to report new movements Alarm notifications after detection out of range temperature lt is possible to program a minimum and or maximum temperature The Mobeye will monitor the actual temperature and sends an alert as soon as the temperature reaches the limit Low battery message The Mobeye will send an SMS text message in case the batteries must be replaced After this you need to change the batteries as soon as possible For some time the Mobeye remains functioning as normal Even when the Mobeye is unset it will measure the battery strength and send the message 1 TO GET READY IN FOUR STEPS To get started with the Mobeye only four steps are needed 1 Place the SIM card in the Mobeye Make sure this SIM card is not secured by a PIN code 2 Place the four batteries 3 Enter at least one phone number in the Mobeye 4 Check the settings In this chapter these steps are explained 1 1 STEP 1 SIM CARD To use the Mobeye a SIM card of any provider is needed On this SIM card the PIN code security needs to be disabled If you have a SIM card with PIN code you can disable this using any mobile phone and switch off the PIN code security Please consult the manual of the used mobile phone for the procedure The SIM card needs to be placed before the batteries When using a prepaid SIM card take care of the remaining value
11. ogenbosch The Netherlands Name J van de Vijver Position Managing Director Signature Date 1 Augustus 2012
12. tal It can be mounted to the wall put down on its side in a cabinet put down with its sensor upward or downward In case you wish to hang the Mobeye the pre punched holes can be opened in order to hang it on screws In order to check the reach of the sensor a sensor test can be executed e Enter your user code e Press menu e Press 511 e Press OK e A confirmation beep is heard First the green light will be flashing After about 30 seconds the light will be on continuously In this mode the sensor test can be done each time the sensor detects a movement a repeating beep will sound Leave the test by entering OK twice 4 5 TEST GSM NETWORK STRENGTH Before using the Mobeye is it advised to test the GSM reach at the location e Enter your user code e Press menu e Press 512 e Press OK The Mobeye now switches on the GSM modules and searches for all present networks It also checks the network strength of the SIM card provider in the device As soon as the GSM network is found the light will turn green The GSM reach of the used SIM card can be read from the LED indicator Green during 30 seconds Reach is good Flashing green Reach is bad No reach Flashing red No valid SIM card or Sim card is not pin code free Besides the telephone number at memory place 01 will receive an SMS text message containing all existing GSM networks sorted by provider It also tells t
13. vice from moisture heat and water splashing The guidelines for the battery usage must be regarded e Do not expose the device to strong vibrations e Do not let it fall from height Do not use in an environment where any inflammable gases vapours or dust are present or could be present e Reparation of the device may only be carried out by people trained for Mobeye repair In case the device must be repaired only original replacement components may be used The use of different parts may lead to damage of the Mobeye Use in accordance with the regulation The use of this device in accordance with the regulation is the generation of SMS text messages and telephone calls after detection of a motion by the motion detector or of a temperature that outreaches the programmed limits Other usages are not permitted Introduction The Mobeye is an easy to install alarm system that will notify you in case of a detection using the built in GSM To use the Mobeye you will need a SIM card of any provider Typical applications are the security of places without any power supply or the temporary security of objects The Mobeye has the following features Alarm notifications after movement detection In case of the detection of an intruder the Mobeye will send an SMS text message to your phone s The Mobeye will also call the phone numbers in order to be sure the message is not missed It is also possible to let the sire
14. wice pressing OK Following settings are possible 00 ______ Change user code 4 digit code 01 ____JChange 1 tel nr Tel number 0 to delete ______ _ Change 2 tel nr a k Sensor sensitivity ron Interval test message T ET o7 Entry indication __ jo 1 em 2 ED lo O os Sien Off ton o 420 SMSonoff Off tom A t i i 13__ Gallonfof_ 0 of ton _ 1 __ Change minimum temperature 000 050 7 until 50 C 999 off Change maximum temperature 000 050 until 50 C 999 off Correction factor temperature 01 09 1 to 9 C ee 5 ai aa n mn 00 no con 3 2 USER CODE The user code is the code for switching on off the active status In the active status the Mobeye will detect movements The user code is also needed to program the settings or activate the special functions It is possible to change the user code to any 4 digit number In case the user code is entered incorrectly 3 times the indicator turns red and the Mobeye will be blocked during 10 minutes 3 3 SMS RECOGNITION TEXT It is possible to send an extra text in the SMS text messages to recognize Mobeye unit sent the message The second part of the SMS text message contains a standard text like Mobeye alarm or Test message OK The recognition text will be written before the standard text This text max 20 characters can be programmed by sending an SMS to the Mobeye Changing the recognition text cannot be done via the
Download Pdf Manuals
Related Search