Home

Phantom 2 Vision User Manual (EN) v1.16

1. An incorrectly inserted battery may cause one of the following to occur Bad contact Unavailable battery information Unsafe for flight Unable to take off 7 4 Battery Usage LED LEDS LEDI LEDA Battery Level Indicator Battery Power Button d C s Built in Battery Power Indicator 1 Checking the battery level When the battery is powered off pressing the battery power button once will indicate the current battery level Refer to Battery Level Indicator Description for details 2 Powering on When the battery is powered off press the battery power button once and then press and hold for 2 seconds to turn on the intelligent battery 3 Powering off When the battery is powered on press the battery power button once and then press and hold for 2 seconds to turn off the intelligent battery More battery information is available in the battery tab of the PHANTOM 2 VISION Assistant Software Description of the Battery Level Indicator The current battery level is shown during both the charging and discharging process Refer to the following table for Battery level indicator Current battery level 2013 2014 DJI Innovations All Rights Reserved 24 details um qum us we 7 5 Correct Battery Usage Notes It s suggested you purchase a new battery after you have discharged your current battery over 500 times It s recommended to charge and discharge the
2. Link Button amp Link Indicator Link Procedures 1 Power off the remote controller power on the aircraft You will see the link indicator blinking red 2 Press the link button with a thin object and hold until the link indicator blinks yellow Release the link button Power on the remote controller and the link indicator should switch off This indicates that the link has been 5 successfully established Link Indicator No signal Switch on the remote controller or perform a link procedure received 0000 In link status Switch on the remote controller 5 7 Compliance Version Configuration The compliance version can be reconfigured by twisting the potentiometer knob See the following diagram on the back of the remote controller using a flathead screwdriver For CE compliance set the remote controller to CE compliance by carefully turning the potentiometer knob to the full counter clock wise position For FCC compliance set the remote controller to FCC compliance by carefully turning the potentiometer knob to the full clock wise position Users should follow their local regulations accordingly 2013 2014 DJI Innovations All Rights Reserved 12 CE FCC When adjusting the potentiometer knob to its limit position be very careful to prevent damaging the potentiometer knob Do not apply too much force during this adjustment Also be sure to use the
3. Supports multi capture continuous capture and timed capture Functions Supports HD Recording JO80p30 1080i60 Supports both RAW and JPEG photo formats 5 2 Main Functions 1 Lens For viewing and photographing with main parameters of f 2 8 FOV 140 Please remove the lens cover when the camera is in use and replace the cover for storage 2 Camera Power Switch on the back of the camera Used to power the camera on and off OFF Powered off CAM ON Power on Wi Fi off WIFI ON Power and Wi Fi are both on Make sure to switch to WIFI ONT and the range extender is powered on if using the DJI VISION App 2013 2014 DJI Innovations All Rights Reserved 18 3 Micro SD Card Slot on the back of the camera Make sure that the Micro SD card is inserted before you take any photos or record any videos Maximum supported Micro SD card capacity is 52GB The DJI VISION App may not be able to read the Micro SD card prepared by the user lt is suggested that you use the DJI VISION App to format the Micro SD card when first used in the camera Refer to the Camera Settings for Micro SD card formatting details 4 Camera Indicator on the back of the camera The Camera Indicator is used to inform the user of the working status of the camera 8 Fast Blink O 1s on O 3s off Synchronizing photos and videos N e Blink Once O 2s on O 3s off Taking a single saptire Blink 5 Times O ls o
4. Plug Set al Screw X12 Screwdriver X 1 Via Jf Lj Y A tf A AAA VA J Lf Assistant Wrench Xl Accessories Box Al IE BEL Required ltems AA Battery x4 2013 2014 DJI Innovations All Rights Reserved 4 Symbol Legend Qo Forbidden Important A Caution Tip Reference Watch the Quick Start Videos This user manual details installation and usage procedures of the product In addition we provide a range of quick start videos It is advised that you watch them fully before attempting to use the product Approach www dji com phantom 2 vision training Preparing for flight Approach 2 Scan the QR code to get the pt a How to connect to the DJI VISION App quick start video link The basics of flying recording and sharing Downloading the DJI VISION App Before attempting to use the product please download and install the DJI VISION App Get the DJI VISION App according to the following methods Download from the App store Search DJI VISION from App Store Approach or Google Play Search DJI VISION from Google Play Approach 2 Scan the QR code to get the Scan and download download link 2013 2014 DJI Innovations All Rights Reserved 5 1 Attaching the Propellers Please use the original 9 inch propellers which are classified by the color of each central nut Damaged propellers can be replaced by purchasing new ones if necessary 1 1 Introduction Propellers Grey N
5. By default the center of the radar indicates the home point that has been recorded by the PHANTOM 2 VISION Tap the center of the radar to switch the center to your mobile device s current location If your mobile device contains a compass the top portion of the Radar is the direction you are pointing If not the radar will be oriented due north 4 Flight Parameters Distance Horizontal distance from home point Altitude Vertical distance from home point Speed Horizontal flying speed V Distance will appear as NA if the PHANTOM 2 VISION is not Ready to Fly 5 Wi Fi Signal Intensity Indicates camera is connected to your mobile device and Wi Fi is working normally The connection between the camera and mobile device may fail if Wi Fi signal strength is low Refer to the lt PHANTOM 2 VISION CONNECTION BROKEN gt on the camera page 6 Aircraft Battery Level 2013 2014 DJI Innovations All Rights Reserved 42 1 When available power is more than 30 the battery icon is blue e g MA This battery level is appropriate for flight 2 When below 30 the battery icon will turn red c g HM and the LED flight indicator will slowly blink red This battery level is low for flight It is recommended that you fly your PHANTOM 2 VISION home and land it as soon as possible 3 After available power drops below 15 c g MIB there is no longer enough power for flight The LED flight indicator will begin to flash red rapid
6. the connection indicator is and communication indicator is blinking Finish configuration in the Main page Finish upgrade in the Info page if necessary 2013 2014 DJI Innovations All Rights Reserved 57 Main page Communication indicator Connection indicator PHANTOM RC i Cl Welcome DJI Phantom Remote Controller The Phantom RC Assistant software is used to configure and upgrade the DJI Phantom Remote Controller Both 5 6GHz and 2 4GHz Language swap Firmware upgrade Stick Mode ompliance Mode Account software e Modet Mode2 FCC CE version Channel Montor aD 4 bilia e 0 Op tt edt MAAMA 2 240 feeeeney AA 1000 lt p 4 na 0 Calibration This image is for reference only Please refer to the actual user interface 2013 2014 DJI Innovations All Rights Reserved 58 14 Troubleshooting FAQ 14 1 How to solve large margin s mid point error If the Remote Controller stick s mid point margin of error is too big the motors will fail to start when you execute the Combination Stick Commands CSC and the aircraft will not take off Below are possible situations where the Remote Controller s stick s mid point margins of error could be too big 1 One of the Remote Controller s stick position except the throttle stick is not centered when powering on the PHANTOM 2 VISION Solution Place all Remote Controller sticks at the
7. After a successful update the firmware bin file s name will change to firmware bin bakOO This file can now be deleted During the update do not turn off the camera or take out the Micro SD card This may prevent your camera from switching on and will need a factory reset A fast red flashing LED after the update means the update has failed Please try again For the v1 1 8 version of the PHANTOM 2 VISION Camera PAL support has been added to the camera including 1080p25 and 960p25 2013 2014 DJI Innovations All Rights Reserved 20 6 Downloading and Installing the DJI VISION App 6 1 Download and Install Download and install approaches Scan the QR code to read the download link Download and install the DJI VISION App on your mobile device You can find the QR code on the Quick Start Guide as well as on the packaging of the PHANTOM 2 VISION Search DJI VISION from App Store download and install on your mobile device Approach 2 Search DJI VISION from Google Play download and install on your mobile device Supported mobile devices Recommended iPhone4s iPhoneb iPhone5s iPhone5C iPod Touch4 iPod iOS iOS6 or above Touch Available but not recommended iPAD3 iPADA iPAD mini Android System 4 0 or above Samsung Galaxy S3 S4 Note2 Note3 or mobile devices of similar configuration DJI continues to support many mobile devices and any information from users are welcome Please send
8. IS STARTING Tie YI OT OR Scr t 5 WEE et E eg lee CT 3 A USA TUBE TION EE 52 AOMEN IDEE Cd aT Te TO eM TOS NaN d Mc aS I5 EE IS Regaining Control During Fan sare Proceed espagne tp un quiatur Petit d unde J3 FATE onte SN E 34 11 5 Low BATTERY CAPACITY E Le eene 54 DJI VISION App Low Battery Capacity Warning x aco E DE t S Rd E itus 34 DESSIN T a a a a a a e a A 35 E E Nas LIIE i E E ND D Yor NM T T O T 35 Eeer 38 T2 DIEW ISIN AP POS Comp 40 PADI VISIOINZA RP MAIN CT AO I2 2 EE 40 E NE 40 Camera Setfihos soo otto 44 EE 47 Camera SD CAII ADU a TRu Min cm DR SUME UM MN EUM CN LI MEE 47 MODI LIOVIC QUA IDEN devia vi basada vie EE 48 EE 49 I2 SETTINGS PAGE tied NND DR RD Meu LEE DN bie C D I DE 50 13 ASSISTANT SOFTWARE INSTALLATION AND CONFIGURATION Qu eesscccssecececececescsceseseeesssescsceceeees 54 13 1 INSTALLING DRIVER AND PHANTOM 2 VISION ASSISTANT SOFTWARE sssscssssssssesescesssssssesesesesessescsesesesseseseseseaees 54 13 2 USING THE PHANTOM 2 VISION ASSISTANT SOFTWARE ON ARC 55 15 5 FIRMWARE UPGRADE OF THE PHANTOM 2 VISION E 56 153 4 PHANTOM RC ASSISTANT SOFTWARE DESCRIPTION rt fberb ined ek ein ide tbc eee eben deve bod e bene dueb eret cete eee kt eed denn 57 14 TROUBLESHOOTING T FAQ E EEN 59 TSAR PEIN B P ANTI CRT 62 LED FLIGHT INDICATORS EE 62 SPECIFICATIONS E 63 2013 2014 DJI Innovations All Rights Reserved 3 In the Box PHANTOM 2 VISION XI 5 8GHz Remote Controller XI Range Extender XI
9. DJI Innovations All Rights Reserved 56 PHANTOM 2 VISION Phantom 2 Vision moore Hardware ID Firmware Upgrade Main Controller 1000646207 1 05 No updates Firmware upgradable items PS 6112 6013 Receivers 8G 15002 01M0036860 1 0 1 3 Latest version 1 0 1 3 Upgrade link P330CB 26000 02F0013818 1 0 1 16 No updates Battery 1000 000000636 16 00 No updates This image is for reference only Please refer to the DO NOT power off until the upgrade is finished If the firmware upgrade failed the main controller will enter a waiting for firmware upgrade status automatically If this happens repeat the above procedures Firmware upgradable items Main Controller GPS 5 8G Receiver P330CB Main Board Battry 13 4 PHANTOM RC Assistant Software Description Please follow the procedures to finish the configuration of the remote controller Turn off the remote controller and find the Micro USB port on the back of it If there is no one users should open the rear cover to find the Micro USB port on the board inner the remote controller Start up the PC power on the remote controller and then Connect the remote controller to the PC with a Micro USB cable DO NOT disconnect until the configuration is finished Run the PHANTOM RC Assistant Software and wait for the remote controller to connect to the Assistant Software Observe the indicators on the bottom left of the screen When connected successfully
10. Signal Indicator SYSTEM Tells you the system status of the range extender eeee The range extender system is working normally The range extender system is working abnormally 2 Power Indicator POWER Tells you the power status of the range extender The range extender is working normally or completely charged Low voltage alert a re charge is required The range extender is charging allow for 5 4 hours depending on USB power output 2013 2014 DJI Innovations All Rights Reserved 14 Make sure to charge the range extender completely before using it for the first time If the power indicator is a solid red light the ranger extender may stop working at any moment Recharge it as soon as possible It is recommended to charge the range extender completely before each use Turn off the range extender after every use Keep the range extender facing the aircraft during flight for the best communication link 3 Lock screw For attaching the range extender on the right side of the remote controller s carrying handle 4 Reset Button Press to link the range extender and the camera 5 Power Switch ON Power on OFF Power off 6 Micro USB Used to charge the range extender 7 Mounting Bracket It has been pre installed on the remote controller s handle It is used to attach the range extender 4 5 Powering on the Range Extender l Toggle the power switch of r
11. any questions or queries to the following mailbox phantom2vision dji com Be aware that the DJI website regularly updates so make sure you visit often as well as the App Store or Google Play in order to download the latest version of the DJI VISION App 6 2 Register amp Login A Access the Internet to register and login Register v t Login v Email Email Password Password Forgot password SHARING 1 o C The App Welcome Page Registration Page Login Page Create New Account Register 2013 2014 DJI Innovations All Rights Reserved 21 1 Register Select Register to enter the registration page Fill in your Email and Password information and then select to create a new account 2 Login Select Login to enter the login page Fill in your registered Email and Password and then select to login A You should login to your account the first time you use the DJI VISION App 2 Ifyou do have an account but forgot the password select the Forgot password to retrieve it 5 Usage tips Useful tips will display when you enter the welcome page Tap the screen to display the next useful tip Camera Connected 5 internet Connected No Wi Fi Connection m E Camera and Remote Album are available when your device is connected to the camera s Wi Fi network Online News is available when sour device is connected to the Internet 2013 2014 DJI Inn
12. battery thoroughly once every 20 charge discharge cycles Users should discharge the battery until there is less than 896 power left or until the battery can no longer be turned on Refer to the DJI VISION App for an exact readout of the battery percentage level You should then fully recharge the battery to maximum capacity This power cycling procedure will ensure the battery is working at its optimal level Turn the power OFF when you have finished flying and remove the battery from its compartment NEVER plug or unplug the battery into the aircraft when it is powered on Take the battery out of the aircraft after every flight and store the battery in a safe and secure place For long term storage please place the battery with only a 40 50 capacity in a strong battery box securely We recommend discharging and charging the battery completely once every 5 months to keep it in good condition The capacity should be varied in such a cycle 40 50 O l0O 40 50 Adhere to the notes for the battery in the disclaimer and regard safety as your first priority The battery should be charged in an environment that is between 10 C to 40 C and be discharged in an environment that is between 20 C to 60 C Both charging and discharging should be in an environment that the relative humidity is lower than 80 It s suggested that you purchase a new battery if the current battery is swollen or damaged in any way Never try to recharge or fly with a b
13. 2014 DJI Innovations All Rights Reserved 28 Wi Fi Connection Indicator Description 0 Solid green Wi Fi is now connected to the PHANTOM 2 VISION 0 Solid blue Wi Fi is connected to another Wi Fi network and NOT to the PHANTOM 2 VISION No Wi Fi connection The first time you launch the DJI VISION App Internet access is required to finish the login process or new account creation The SSID is unique for each PHANTOM 2 VISION which should appear in your Wi Fi list as Phantom xxxxxx Always connect to the SSID starting with Phantom xxxxxx FC200 Oxxxxx is the SSID of the camera and should not be connected to If the SSID FC200 Oxxxxx is connected to then the connection signal range will be extremely shortened 2013 2014 DJI Innovations All Rights Reserved 29 10 Calibrating the Compass IMPORTANT Make sure to perform the Compass Calibration procedures prior to the first flight The compass is very sensitive to electromagnetic interference which causes abnormal compass data and leads to poor flight performance or even flight failure Regular calibration of the compass enables the compass to perform at its optimal level 10 1 Calibration Warnings DO NOT calibrate your compass where there is a possibility for the existence of strong magnetic interference such as magnetite parking structures and steel reinforcement underground DO NOT carry ferromagnetic materials with you during calibration such as keys or ce
14. 5 times or more will reset the current aircraft position as a new home point of PHANTOM 2 VISION When successfully reset you will see a series of rapid green blinks on the LED Flight Indicator The definition of home point is i The home point is the place PHANTOM 2 VISION returns to when the control signal is lost which is recorded last time ii The home point is used to calculate the horizontal distance between you and the aircraft the distance will be displayed on the DJI VISION App Regaining Control During Failsafe Procedure Position of Switch SI Position l Position 2 Position 3 When the SI switch is switched to Position l toggle the S switch to any other position once to Regain control as soon as signal How to regain control regain control If remote controller s signal is is recovered recovered control is returned back to the pilot 2013 2014 DJI Innovations All Rights Reserved 33 Failsafe on the DJI VISION App The DJI VISION App will provide information during Failsafe E E C co CONTROL SIGNAL LOST GOING HOME aT sal a Kr Distance 5 0ft Altitude 266 6ft Speed 0 4mph a5 Distance 4 2ft Altitude 267 0ft Speed 0 0mph Control Signal Lost Indicator Going Home Indicator Refer to the lt DJI VISION App Usage for details 11 5 Low Battery Capacity Warning Function The low battery capacity warning alerts users when the battery is close to depletion during flight Whe
15. All Rights Reserved 51 t Preview Quality 640x480 15fps V 320x240 30fps 320x240 15fps High 640 x 480 15fps Medium 320 x 240 3Ofps Low 320 x 240 15fps Recommended when there is a lot of interference 5 Parameter Unit Select imperial or metric units of measurement 6 Auto Flips The user interface of the DJI PHANTOM 2 VISION App will flip if the mobile device s auto flip is enabled 7 Low Battery Warning If enabled an alarm will sound when the battery level is too low Be sure sound is enabled on the mobile device and try to adjust the volume to the highest level 8 Tutorial Usage tips will be displayed 9 Clear News Cache Tap to clear news cache 10 Binding In the event the camera and range extender bind is lost or one of them requires repair or replacement camera and range extender binding should be performed via the DJI VISION App Refer to the How to Perform a Camera amp Range Extender Binding for details 11 Find My PHANTOM 2 VISION 2013 2014 DJI Innovations All Rights Reserved 52 My PHANTOM 2 VISION Standard Satellite My location PHANTOM 2 VISION S location ot omn TER IM Satellite Mode 12 Account Tap to see user s account information 13 Rate My PHANTOM 2 VISION My location PHANTOM 2 VISION S location Standard Mode Tap to rate the DJI VISION App Internet access is required 14 About Tap to see the c
16. Environment Requirements Before your first flight please allow yourself some flight training Using a flight simulator to practice flying getting instruction from an experienced person etc DO NOT fly in bad weather such as rain or wind more than moderate breeze or fog The flying field should be open and void of tall buildings or other obstacles the steel structure within buildings may interfere with the compass Keep the aircraft away from obstacles crowds power lines trees lakes and rivers etc Try to avoid interference between the remote controller and other wireless equipment No base stations or cell towers around The flight control system will not work properly at the South Pole or North Pole All parts must be kept out of the reach of children to avoid CHOKING HAZARDS if a child has accidentally swallowed any part you should seek immediate medical assistance 11 2 Starting the Motors A Combination Stick Command CSC is used to start the motors instead of simply pushing the throttle stick up This is a safety precaution to prevent the motors from accidentally spinning up Push both sticks to their bottom corners as indicated in the diagram below to start the motors Once the motors have spun up release both sticks simultaneously The same combination stick command CSC is used to stop the motors 11 5 Takeoff Landing Procedures IL Start by placing the PHANTON 2 VISION on the
17. PHANTOM 2 VISION User Manual V1 16 April 7 2014 Revision Congratulations on purchasing your new DJI product Please thoroughly read the entire contents of this manual to fully use and understand the product It is advised that you regularly check the PHANTOM 2 VISION s product page at www dji com which is updated on a regular basis This will provide services such as product information technical updates and manual corrections Due to any unforeseen changes or product upgrades the information contained within this manual is subject to change without notice If you have any questions or concerns regarding your product please contact your dealer or DJI Customer Service 2013 2014 DJI Innovations All Rights Reserved Index INID deer m 2 Ls Fal e GP derer I T LI T 4 CAS ere HR KEE A SYMBOLULEGEND EE 5 WATCH THE QUICK START VIDEOS E 5 DOWNLOADING THE DJI VISION APP iniscccs oce tied ei en pod rane en eate ded rhe ee sek dea eae aee a dou aio e peers 9 LATITAGHING THE EE 6 TTI ROD Breng re ENEE LZASSEMBLY Scene RR NUM NON AMAN NONE NEA NB WENN NNNM NE NBN NBN M Is T ERBIMOMINGTHESPSROPBULERS E terree tma p ER M A A A em LM E SE 6 2 INSTALLING THE RANGE EXTENDER AND MOBILE DEVICE HOLDER eere eere ennnnnnntnnnns 7 2 1 INSTALLING THE RANGE EXTENDER deer gedet 7 2 2 INSTALLING THE MOBILE DEVICE HOLDER 2c sevcvscessoassessncpislasswe
18. aft will start to fly back descend and land at the Home point automatically Please make sure there are no obstacles within the go home route and you are familiar with the regaining control procedure 14 5 Wi Fi connection fails all the time Solution Double check the current Wi Fi connection status of the mobile device The mobile device may be connecting to other Wi Fi networks after a connection breaks with the PHANTOM 2 VISION 2013 2014 DJI Innovations All Rights Reserved 59 14 6 Files fail to synchronize Solution Video files that are too large file sizes close to 4GB cannot be synchronized to the mobile device Some mobile devices also fail to support synchronization of the 1080i60 video files 14 7 Albums fail to synchronize Solution Reset the settings of your mobile device as illustrated below Enable the Settings gt Private gt Photos gt DJI VISION Otherwise the Albums will fail to synchronize with your mobile device MM w C21 2000 kd Airplane Mode OFF Location Services On gt Photos stored on your iPod touch may ua contain other information such as when Ka WLAN Phantom 100cd9 gt and where the photo was taken Contacts gt 9 Bluetooth On gt S rs Calendars gt 59s DJI VISION C Do Not Disturb OFF gt DJIHand m m ue Photos gt Apps that have requested access to your ki Notifications gt photos will appear here RJ Bluetooth Sharing gt ks General gt LU T
19. ange extender to ON position 2 Wait for approximately 30 seconds The Wi Fi signal indicator should blink green indicating the range extender is communicating properly It is advised that you power off the range extender after every flight to avoid discharging the battery 4 4 How to Bind the Camera amp Range Extender If the camera and range extender connection is lost or one of them needs to be repaired or replaced a camera and range extender binding will need to be performed via the DJI VISION App 2013 2014 DJI Innovations All Rights Reserved 15 ow Jor Ko Reset Button O l Power on the camera and range extender Note Place the camera power switch to the WIFI ON position 2 Approximately 50 seconds later press the reset button on the range extender with a thin object until the Wi Fi signal indicator turns off The range extender will then restart automatically 5 Approximately 50 seconds later the Wi Fi signal indicator should start to blink green which indicates the range extender is now ready to be bound 4 Find and select the Phantom xxxxxx via the Wi Fi list on the mobile device to connect the range extender 5 Fig l Run the DJI VISION App gt Settings gt General gt Binding Fig 2 Select Scan the QR Code to scan the camera QR code on the product packaging Fig 5 Get the camera SSID E g FC200 Oxxxxx and the MAC address select the tick on the top right corner T
20. attery that is swollen or damaged in any way Never charge the battery unattended Always charge the battery on a non flammable surface such as concrete and never near any flammable materials 2013 2014 DJI Innovations All Rights Reserved 25 8 PHANTOM 2 Aircraft 8 1 The Aircraft 8 2 Built in Flight Control System Instructions Propeller Motor Front Side Front LEDs Micro USB Vibration Absorber Compass LED Flight Indicators DJI Intelligent Battery Servo Receiver Antenna Landing Gear The built in flight control system is used to control the entire aircraft s functions in flight such as Pitch forwards and backwards Roll left and right Elevator up and down and Yaw turn left or right The flight controller contains the MC Main Controller IMU GPS compass receiver and LED indicators The IMU Inertial Measurement Unit has a built in inertial sensor and a barometric altimeter that measures both attitude and altitude The compass reads geomagnetic information which assists the GPS Global Position System to accurately calculate the aircrafts position and height in order to lock the aircraft in a stable hover The receiver is used to communicate with the remote controller and the MC acts as the brains of the complete flight control system connecting and controlling all the modu
21. correct sized screwdriver It is recommended to use a flathead screwdriver of 2 4mm for adjustment You can use the DJI screwdriver with the flathead for adjustment There is another potentiometer reserved 2013 2014 DJI Innovations All Rights Reserved 13 4 Preparing the Range Extender The PHANTOM 2 VISION range extender is a wireless communication device that operates within the 2 4 GHz frequency band and is used for extending the effective range of communication between a mobile device Smartphone and the PHANTOM 2 VISION In an open unobstructed area the transmission distance can reach up to 500 meters but is usually affected by the surrounding environment such as trees buildings and other sources of the same frequency Before every flight it is suggested that you ensure the range extender functions properly Otherwise you may experience a communication issue with the mobile device and the PHANTOM 2 VISION Each range extender has a unique MAC address and network name SSID details of which are printed on the back label as Phantom xxxxxx The xxxxxx represents the last six letters or numbers of the MAC address for the range extender 4 1 The Range Extender Wi Fi Signal Indicator 4 Power Indicator SYSTEM POWER Lock screw Reset Button Power Switch l o Front View Right View Mounting Bracket Micro USB 4 2 Function Description 1 Wi Fi
22. erbesiecereesses 20 6 DOWNLOADING AND INSTALLING THE DJI VISION APP wou cccssssscsssssssssessesscsssssssssssssescsssssseseeseesees 21 O Bre ISI AD NP US SAPERNE I 21 OA Oe ST PaO OENE d o ei M A e 21 7 PREPARING THE EEIGHTIBATTERY ioo eh E aba SO teen E ba ero EU e DEN 25 7 1 INTELLIGENT BATTERY AND CHARGER INSTRUCTIONS 253 7 2 CHARGING PROCEDURES ccivacivatextcaadevecssncovacevaconaes asevanssaseweseseconave eseveassassbese aoohosabess veuosaushiensbwopnecabessveusheeshenevasobosabessueuesocavees 25 ZO NSTANETHEIEAPLERY ette E UOTE REDE RI PRIN DIES A EM mE MEE E E RE E 24 Pe KE E E 24 Descripiotof the EE 24 2013 2014 DJI Innovations All Rights Reserved 7 CORRECT BATIERY USAGE NOTES ioca ooo EO OO oO GO eG oe d CO E OUR 25 Ee CR ae E EE 26 n THE err ig m 26 8 2 BUILT IN FLIGHT CONTROL SYSTEM INSTRUCTIONS ee 26 8 53 LED FLIGHT INDICATORS DESCRIPTION EE 26 oY CONNECTING TO THE el EEN 28 O ICAMBRASCONBNECTIIONTPROGEDURIS etae ette Ep E opta pe i P ESPERE E bU NES UE An UE NR ER EMT MI EUM DUM M UE 28 ebe WR e Lean ele 50 IQ GALIBRATION WARNING Sininen iran e cH e ch RS ERE ranean rep Ple o eo o Pel rh ene con e RE REPRE iR 50 10 2 CALIBRATION E 50 10 5 WHEN RECALIBRATION IS REQUIRED osse beaten PEE UNDE Go Pepe tonto E UE e ania tin Mola ERE PR EH bec E EU Deus 50 MB C M Ss Al 11 1 FLYING Eege Le EN 5
23. flight experience 2013 2014 DJI Innovations All Rights Reserved 6 2 Installing the Range Extender and Mobile Device Holder 2 1 Installing the Range Extender l Adjust the range extender to align with the mounting bracket installed on the carrying handle 2 Tighten the lock screw to affix the range extender on the right side of the carrying handle 1 Make sure the assembly orientation is correct with the LED side facing you Ay 2 To obtain better communication try to keep the range extender facing the aircraft during flight e SS wT Lock Screw 2 2 Installing the Mobile Device Holder Tighten the Philips screws as shown to correctly attach the mobile device holder on the left side of the carrying handle 2 Affix the mobile device sideways within the holder Make sure the assembly orientation is correct The mobile device should be facing you when mounted It is recommended not to use oversized mobile devices e g iPad which cannot be placed into the Mobile Device Holder 2013 2014 DJI Innovations All Rights Reserved 7 5 Preparing the Remote Controller The PHANTOM 2 VISION remote control is a wireless communication device that uses the 5 8GHz frequency band It is compliant wi
24. g Current Voltage Battery Camera Resolution FOV Sensor Size Functions Range Extender Operating Frequency Communication Distance open area Transmitting Power Power Consumption DJI VISION App Supported Mobile Devices System Requirement of Mobile Device DJI 5200mAh Li Po Battery 1160g Vertical O 8m Horizontal 2 5m 2007s 3557 Ascent 6m s Descent 3m s 15m s Not Recommended 550mm Q 60 5 728 GHz 5 85 GHz CE Compliance 500m FCC Compliance 500m 93dBm CE Compliance 25mW FCC Compliance 125mW 80 mA 6V A AA Batteries 14 Megapixels 140 120 90 LS Supports multi capture continuous capture and timed capture Supports HD Recording 1080p50 1080160 Supports both RAW and JPEG photo formats 2412MHz 2462MHz 500m 17dBm 1 5W Recommended iPhone4s iPhoned iPhoneds iPhone5C iPod Touch4 iPod Touch5 Available but not recommended iPAD3 iPADA iPAD mini Samsung Galaxy S5 S4 Note2 Note3 or phones of similar configuration iOS 6 0 or above Android system 4 0 or above 2013 2014 DJI Innovations All Rights Reserved 63
25. ght velocity The roll stick controls the aircraft left amp right tilt Push the stick left and the aircraft will tilt and fly left Push the stick right and the aircraft will tilt and fly right The aircraft will keep level and straight if the stick is centered Increasing movement of the command stick will result in a larger tilt angle maximum is 35 and faster flight velocity Sl is for compass calibration Toggle the Sl from position l to position 5 and back to position l about 6 to 10 times which will force the aircraft to enter into Position l Position 2 Position 5 compass calibration mode For Ready to Fly the aircraft will hover hold a stable horizontal position when all sticks are released For Ready to Fly non GPS the aircraft will keep the aircraft level without horizontal positioning when all sticks are released 3 6 Link between the Remote Controller and Receiver There is a 5 8G receiver in the PHANTOM 2 VISION with the link button and indicator located on the bottom of the aircraft as illustrated in the following diagram The link between the remote controller and aircraft is already established for you so you can initially skip this procedure If you ever replace the remote controller re establishing the link is required 2013 2014 DJI Innovations All Rights Reserved 11
26. ground with the battery level indicator facing you 2 Power on the remote controller 5 Power on the range extender 4 Switch the camera to the WIFI ON position 5 Power on the aircraft by turning on the intelligent battery refer to Battery Usage for details 6 Connect the mobile device to the PHANTOM 2 VISION and then run the DJI VISION App to enter the camera preview page 7 Wait until the LED flight indicator starts to slowly blink green yellow This means the aircraft is initializing and entering the Ready to Fly Ready to Fly non GPS state Then proceed to execute the CSC 2013 2014 DJI Innovations All Rights Reserved 31 command to start motors 8 Push the throttle stick up slowly to lift the aircraft off the ground Refer to Remote Controller Operation Mode for more details 9 Enjoy your flight while capturing and recording with the DJI VISION App Refer to the lt DJI VISION App Usage for more details 10 Be sure you are hovering over a level surface Pull down on the throttle stick gently to descend and land I After landing the aircraft on the ground keep the throttle stick at its lowest position for about 5 to 5 seconds which will automatically stop the motors You SHOULD NOT execute the CSC during normal flight This will stop the motors and cause the aircraft to descend rapidly and drop without any type of control When the LED flight indicator blinks yellow rapidly during flight the aircraf
27. he airspace A B C of restricted special area LED flight indicators will blink 000000 status and continue for 5 seconds at which point it will switch back to red blinking quickly and continue for 3 seconds then switch to indicate current flying For safety reasons please do not fly close to airports highways railway stations railway lines city centers and other special areas Try to ensure the aircraft is visible 6 3 Conditions of Flight Limits In different working modes and flight modes flight limits will differ according to number of GPS satellites found The following table demonstrates all the cases V available x unavailable All flights are restricted by height distance and special areas simultaneously Failsafe and Ground Station operations are not restricted to flight limits but if Ground Station function is used the flight will be restricted the special area limits built into Ground Station Refer to the Ground Station manual for details Flight Status Limits of Special Area Max Height Control Mode Disclaimer Please ensure that you are kept up to date with International and Domestic airspace rules and regulations before using this product By using this product you hereby agree to this disclaimer and signify that you have read this fully 2013 2014 DJI Innovations All Rights Reserved 38 You agree that you are responsible for your own conduct and content while using this product and for any d
28. he range extender should automatically restart The binding procedure is now complete ha Settings ha Binding v GENERAL Current Binding SSID Auto Flips om Low Battery Warning omit MAC Address Tutorial Clear News Cache Binding Find My PHA OTHER Account djitest amp dji corr Rate About Scan the QR Code u Fig l Fig 2 QR code is only for example 2013 2014 DJI Innovations All Rights Reserved 16 Binding v Current Binding SSID MAC Address FC200 0041c0 1F 00 41 CO Scan the QR Code Fig 3 If both the camera and range extender are powered on and working normally you will be able to find the SSID on the Wi Fi list of the mobile device DO NOT push the reset button of the range extender unless you are ready to rebind the range extender and the camera This will unbind your camera and you must follow the steps above to rebind The QR code is located on the packaging of the PHANTOM 2 VISION If you cannot find the QR code please contact DJI customer service to receive the QR code related to your camera s serial number 2013 2014 DJI Innovations All Rights Reserved 17 5 Preparing the Camera 5 1 The built in camera Lens Camera Power Switch Micro SD Card Slot Camera Status Indicator Camera Cable Capture Record Button
29. he switch from left to right to enable this function The toolbar will auto hide on the camera page Toolbar Auto Hide Disabled Toolbar Auto Hide Enabled 2 When Connection Breaks 2013 2014 DJI Innovations All Rights Reserved 50 When Connection Breaks Stop Recording d 15 Stop recording or not when the connection is broken while the camera is in recording state Start Recording Start Continuous Capture Stay in Idle eS 16 Which state the camera will enter when the connection is broken while the camera is in idle state 15 Stop Recording Enabled Stop recording when the Wi Fi connection between the mobile device and the camera breaks while the camera is recording Disabled Keep recording when the Wi Fi connection between the mobile device and the camera breaks while the camera is recording 16 Select the state the camera will enter in the event of a Wi Fi Connection break between the mobile device and the camera Use this function to ensure you continue to capture the scenes you don t want to miss during a flight 5 Camera Settings Display For iOS users an enabled item will display in the camera settings toolbar while a disabled item will be hidden For Android users there is no this item ba Camera Settings Display Photo Format ISO White Balance Exposure Metering Exposure Compensation Sharpness Anti flicker Reset Format 4 Preview Quality 2013 2014 DJI Innovations
30. in accordance with the Phantom Pilot Training Guide If the Naza M function is enabled users can switch the control mode to either the ATTI Mode GPS Mode or Manual Mode and access the advanced settings e g IOC In addition the LED located on the rear frame arms will display the flight status according to the Naza M s indicator instead of the Phantom 2 Vision s indicator Do not enable the Naza M function unless you are an experienced user or guided by a professional 2 You can change to the Phantom 2 Vision function by tapping the same button if the Naza M function is enabled This operation will disable the Naza M function and enable the Phantom 2 Vision function All parameters will be returned to factory settings 13 3 Firmware upgrade of the PHANTOM 2 VISION Please refer to the PHANTOM 2 VISION Assistant Software to install driver and PHANTOM RC Assistant Software and then follow the procedures below to upgrade the software and firmware otherwise the PHANTOM 2 VISION might not work properly Ii An internet connection is required to upgrade the PHANTOM 2 VISION s firmware 2 Click the Upgrade icon to check the current firmware version and whether the installed firmware is the latest version If not click the relative links to upgrade 5 Be sure to wait until the Assistant Software shows finished Click OK and power cycle the PHANTOM 2 VISION after 5 seconds Once completed the firmware is up to date 2013 2014
31. ions All Rights Reserved 49 The World Wide Landscape The World Wide Mv ond gt Landscape Aerial Video Collection Exciting new releases at NA April amp 2013 a DJI ZENMUSE GIMBAL FOR Dat GM February 22 2013 DJI is going to host an aerial videography collection event aiming at collecting M The Spirit of Flight Phantom amazing aerial videos which are filmed in February 4 2013 gt the open air with wonderful shots or footage using the professional DJI Spreading Wings 5800 Wookong E DYI Launches Industry Beat M Zenmuse Z15 The videos are WI January 7 2013 gt expected to help people to see the world from a special perspective and to demonstrate the unique features of the DJI Launches Its Wikipedia selected filming site such as the Fuj October 26 2012 gt Mountain in Japan the Dutch Windmills in Finland St nehenne in Fnalanrt the News List News Details 12 5 Settings Page t Settings W Settings GENERAL CAMERA 6 Auto Flips C 1 Toolbar Auto Hide 7 Low Battery Warning eg 2 When Connection Breaks gt 8 Tutorial 5 Camera Settings Display gt 9 Clear News Cache gt 4 Preview Quality gt 0 Binding gt San oer 11 Find My PHANTOM 2 VISION gt 5 Parameter Unit LI OTHER SS 12 Account gt Auto Flips Gm 13 Rate gt Low Battery Warning om 1 A About gt Tutorial 1 Toolbar Auto Hide Slide t
32. ir mid point positions and then power cycle the PHANTOM 2 VISION to re record the mid point If the problem persists this can be caused by scenario 2 2 The Remote Controller sticks have been trimmed which leads to a large deviation of the mid point position Solution Use the Assistant Software to perform a Remote Controller calibration To do so carry out the following procedures a Connect to the Assistant Software tap Basic gt RC gt Command Sticks Calibration and push all Remote Controller sticks through their complete travel range to see if any stick cannot reach its outer most position b Power cycle the PHANTOM 2 VISION Note that a power cycle is required c Redo the Remote Controller calibration according to the Assistant Software If the above solutions do not solve your issue please send your Remote Controller to DJI Customer service for repair 14 2 How to restore a video file if power is turned off during a recording session Solution Keep or place the Micro SD card back into the camera Power cycle the camera and wait about 5O seconds for the video file to be restored 14 5 Failure to acquire the SSID Solution Double check whether both the camera and Range Extender are powered on and the power switch of the camera is switched to WIFI ON 14 4 What to do if PHANTOM 2 VISION is out of sight and the Wi Fi connections is lost Solution Turn off the Remote Controller to trigger the Failsafe mode and the aircr
33. irect or indirect consequences caused by not following this manual violate or disregard any other applicable local laws administrative rules and social habits thereof 2013 2014 DJI Innovations All Rights Reserved 39 12 DJI VISION App Usage The DJI VISION App controls the PHANTOM 2 VISION camera including capture and recording settings pitch angle adjustments and displays essential status including flight parameters and battery life 12 1 DJI VISION App Main Menu After login you will come to the main page This shows the current Wi Fi connection and four app function icons Phantom 000012 CAMERA ALBUM A ei NEWS SETTINGS es ONE Tap to enter App settings Connect your mobile device to the PHANTOM 2 VISION Wi Fi network to use the camera and onboard album Connect your mobile device to the internet mobile or Wi Fi to share photos videos and read DJI news If you receive a phone call during flight the live camera preview screen may be interrupted It s recommended to ignore the call and pay full attention to your flight 12 2 Camera Page 5 Basic Use 6 1 2 2013 2014 DJI Innovations All Rights Reserved 40 1 Return Return to the preview page 2 Camera Tilt Control Tilt Control Mode Tap and hold to enter the Accelerometer Sensor Mode Release to return to normal mode Normal Mode Tap up arrow A to pitch camera upwards and down arrow E to
34. is finished 2 Run the PHANTOM 2 VISION Assistant Software and wait for the PHANTOM 2 VISION to connect to the Assistant Software Observe the indicators O on the bottom of the screen When connected successfully the connection indicator is and communication indicator is Staten 1 5 Choose Basic or Advanced configuration pages 4 View and check the current configuration in the View page 2013 2014 DJI Innovations All Rights Reserved 55 Function switch between PHANTOM 2 VISION and NAZA M O gt P te Account software View configurations E F Advanced T Us fe nfi version RC Gain Ej Irmware r e Advanced Ypg ad Aircraft Motor Gim bal Batte di GPS Location Mixer Type Quad rotor X Motor Idle Speed Recommended M U calibration Cut Off Type Intelligent 0cm Y 0cm 2 9 Receiver Type D Bus FS Failsafe Methods Go Home and Landing Gain Pitch Roll Yaw Vertical IOC Intelligent Onentation Control OFF Basic 12036 120 120 120 Attitude 200 200 Gimbal Gimbal Switch ON Channel Monitor vuan satt r T 0 Battery E EJ at 0 Current Voltage Dm tj d 0 Current Capacity 096 Communication n First Level Waming 30 This image is for reference indicator only Please refer to the OnLine Help actual user interface Connection indicator 1 Users should not enable the Naza M function before finishing the Advanced Flight Maneuvers procedure
35. is turned on and volume is turned up on your mobile device 3 The aircraft battery icon will turn red 2013 2014 DJI Innovations All Rights Reserved 34 ge D 4 kd Distance 5 7ft Altitude 148 4ft Speed 0 0mph Low Battery Capacity Warning Refer to the lt DJI VISION App Usage for details 1 Remember to fly your PHANTOM 2 VISION back as soon as you see a low battery capacity warning i 2 The PHANTOM 2 VISION is Ready To Fly Ready to Capture and Ready to Share but it is still an aircraft Keeping the battery contact needles and pads clean is very important Any dirt and dust may cause a communication failure 11 6 Flight Limits All UAV unmanned aerial vehicle operators should abide by all regulations from such organizations at ICAO International Civil Aviation Organization and per country airspace regulations For safety reasons the flight limits function is enabled by default to help users use this product safely and legally The flight limits function includes height distance limits In Ready to Fly status height and distance limits works together to restrict the flight In Ready to Fly non GPS status only height limit works and the flying height restricted to be not over 120m The default parameters in the Assistant Software is compliant within the definitions of class G ruled by ICAO Refer to Airspace Classification to get more details As each country has its own rules make sure to co
36. les together 8 5 LED Flight Indicators Description After powering on the intelligent battery the LED flight indicators light up to show the aircraft s current status mv LI HHH Ki i rs LED Flight Indicators um d H SER Front LEDs 2013 2014 DJI Innovations All Rights Reserved 26 Ly e zi n ski Battery Power Indicator Front LEDs The front LEDs are for indicating where the nose of the aircraft is They light up solid red only after the motors have started spinning LED Flight Indicators Description tomronsatten 990900 wema 00990 ncmo arer 00000 suum spuren 00000 seem te me Fast blinking yellow Refer to lt Failsafe Remote Controller Signal Lost Function 1 Level Low Battery Capacity Warning 00000 Slow blinking red 2 Level Low Battery Capacity Warning 000000 Fast blinking red Keep aircraft stationary or perform Not Stationary or Sensor Bias is too big IMU calibration Compass Needs Calibration 00000 Refer to lt Calibrating the Compass 1 The aircraft should be kept stationary on level ground before takeoff 2 Make sure the aircraft s status is in Ready to Fly or Ready to Fly non GPS mode before takeoff 3 If an error occurs LED is solid red please connect to the PHANTOM 2 VISION Assistant Software for more detailed information Remote con
37. llular phones Compass Calibration is very important otherwise the flight control system will not work properly 10 2 Calibration Procedures Choose an open space to carry out the following procedures Please watch the quick start video of the PHANTOM 2 VISION for more compass calibration details 560 Rotate the aircraft 360 Rotate the aircraft horizontally vertically Nose downward NM Position 1 GF ee SR Quickly flip the switch SI H gt A A p EA N Y dei Pr IER o Wl Position 3 1 SS i l j y Start A l B UE L li h f am y sed Position 1 Position 3 Position Eo 1 hs Flip 6 1O times S ME LED Flight Indicator LED Flight Indicator LED Flight Indicator poem E wma 19099 Start horizontal calibratic Start vertical calibration Succeed Fail WE Dm S 1 DIA Position l 77 te 4 Re calibrate 4 Position 3 Ei Position l Position 3 Position Flip once 10 3 When Recalibration is Required 1 When Compass Data is abnormal the LED flight indicator will blink alternating between red and yellow 2 Last compass calibration was performed at a completely different flying field location 3 The mechanical structure of the aircraft has changed i e changed mounting position of the compass 4 Evident drifting occurs in flight i e the aircraft doesn t fly in straight lines 2013 2014 DJI Innovations All Rights Reserved 30 11 Flight 11 1 Flying
38. ly and the PHANTOM 2 VISION will begin an automatic descent and land The available power thresholds mentioned above can be adjusted in the PHANTOM 2 VISION Assistant al e E Software 7 Aircraft GPS Status Displays GPS status and the number of available satellites The icon is highlighted when more than 6 satellites are found enabling Ready to Fly mode 8 Micro SD Card Status Displays Micro SD Card Status The icon is highlighted when a valid Micro SD card is inserted If there is no Micro SD card present it is grayed out 9 Remaining Shots Displays estimated shots remaining based on the current Photo Size setting of camera and the storage capacity of the Micro SD card This shows O if 1 Micro SD card is not inserted 2 Micro SD card is full 3 Micro SD card is damaged 4 Connection between the DJI VISION App and camera is broken 10 Shutter Button Tap to take photos Single capture press once for a single capture Continuous capture press once for 5 or 5 captures Timed capture press once to begin a timed capture press again to stop Shutter button is disabled during video recording Capture modes can be reconfigured in camera settings refer to the Camera Settings 11 Record Button 2013 2014 DJI Innovations All Rights Reserved 43 Start and Stop video recording Tap once to start recording A red dot will blink to indicate recording is in progress and a time elapsed cou
39. n O ls off lening 2 ar o photes per eici e Fast Blink O ls on O 3s off EWERS Upgrading hd Slow Blink O 2s on 1 8s off CMOS sensor error Blink Once O 2s on O 3s off Operation failed Blink 3 Times O 1s on O 1s off Micro SD Card error Fast Blink O ls on O 3s off 2013 2014 DJI Innovations All Rights Reserved 19 O 5s green O 5s yellow O 5s red O 5s Off ON OFF Camera has overheated When camera temperature rises above 80 C the LED indicator will blink 49 The camera will automatically power off if the temperature rises above 85 C 5 Camera Cable on the back of the camera Make sure that the camera cable is firmly attached to the camera before powering the camera on 6 Capture Record Button on the bottom of the camera Capture function Press the button once less than 2 seconds to take a single capture Record function Press the button once greater than 2 seconds to begin recording Press once again to stop 5 3 Upgrading the Firmware of Camera Follow the below instructions to update your firmware k Download the latest firmware of camera from DJI website 2 Copy the firmware bin file to the root folder of your Micro SD card 5 Insert the SD card into the camera before turning it on 4 Turn on the camera 5 The firmware update will begin automatically A yellow flashing LED indicates that the camera is updating 6 When the yellow flashing disappears the firmware has been updated
40. n it appears users should promptly fly back and land to avoid accidental damage The PHANTOM 2 VISION has two levels of low battery capacity warning The first appears when the battery has less than 30 power and the second when it has less than 15 When battery power drops below 30 an LED indicator will blink red slowly and an alert will show on the DJI VISION app refer to the DJI VISION app Low Battery Capacity Warning At lower than 15 the LED indicator will blink red rapidly and the DJI VISION app will sound an alarm refer to the lt DJI VISION app Low Battery Capacity Warning The PHANTOM 2 VISION will also begin to descend and land automatically After it has landed keep the throttle stick at its lowest point or execute CSC refer to Starting the Motors If you push the throttle stick above the mid point the PHANTOM 2 VISION will ascend slowly Use the throttle pitch roll and yaw sticks normally to find a more appropriate landing area if required There is a hidden third low battery threshold in addition to the Ist and 2nd level warnings This uses 10 65V as its threshold Both this voltage threshold and the 2nd Level Low Battery Warning will trigger auto landing Altitude can be maintained if necessary by pulling up on the throttle DJI VISION App Low Battery Capacity Warning DJI VISION App will show low battery capacity warnings 1 A red rectangle will blink on the camera screen 2 Audible alarm Make sure the sound
41. nadedssuptcessvcpesansvcpeceds vanasessvcpisland veyadeds vapsseysecpavandnepboedevanicestuantes 7 5 PREPARING THE REMOTE CONTROLLER atop hat nas eoo ex v ua obra aa eoo a rn aad a tea teer 8 ENK KE Te ug erh e EI 8 5 2 POWERON THE REMOTE CONTROLLER A edere ie nette ee ee vein in ci ebrei ei es e inum ein eie vesti iive eise eiue e een 8 5 5 REMOTE CONTROLLER POWER INDICATOR STATUS INFORMATION eeeenetnetnennennennenne nne nne nne nne nne tne tne tne tette einen esee nen 9 5 4 ANTENNA ORIENTATION eR jJ 9 OOTWBENMOLIBECONESGEBERAXOBERATIOH ee 10 5 6 LINK BETWEEN THE REMOTE CONTROLLER AND RECEIWER 1l ENT FOC OCIA EIS do si raid D m E A EE don ep oe OR UU CR o eo o dove Ad o dove qs 12 Lee 2 53 7 COMPLIANCE VERSION Re Te Deg er 12 4 PREPARING THE RANGE EXTENDER eerste eege l4 4 THE RANGE EXTENDER pns e davidttiute iiber ediderat tes ENAR bus eoe ES cr e aic E ceto es NNN l4 42 FUNCTION DESCRIPTIONS d hb on neon rne pn vn en vn o pen vn nen oon l4 4 5 POWERING ON THE RANGE EXDIENDEB s a NR ERE n Oe RR i ei t a v a eens 15 4 4 How TO BIND THE CAMERA amp RANGE ESTENDER AAA 15 5 PREPARING THE CAMERA EE 18 5 1 THE BUILT IN CAMERA RI 9 99 18 EE TONS rea Sis acetates UN UE ML D M MEE testi DUE e e S 18 5 3 UPGRADING THE FIRMWARE OF CAMERA cc cccssvsssuecevsessesesdestesevsestesevsecsecensesvencesessesersesvecendosvesevsesuasessecsesendesven
42. negative and positive poles 2 Set the Sl and S2 switches to the upper most position and all sticks are at mid point before switching on the power switch 5 There is a power on indicator beep If the remote controller is set to be CE compliant then there will be one beep while the FCC compliant version will emit 2 beeps The power indicator blinks green quickly indicating the remote controller and receiver is linking Once fully linked the power indicator will change to a solid green 2013 2014 DJI Innovations All Rights Reserved 8 EA gt X If the low voltage warning alert sounds refer to the Remote Controller Power Indicator Status Information please replace batteries as soon as possible Using the incorrect type of battery may prevent a risk of damage Remove the batteries after use and dispose of them safely For long term storage be sure to remove the batteries from the remote controller 3 3 Remote Controller Power Indicator Status Information eeeeee Non Establishing a link between the remote controller and the receiver Low voltage lower than 5 9V The remote controller will automatically power off Batteries should be replaced immediately The remote controller will give a visual indication of an alarm after 15 minutes of non operation The alarm status will disappear once you start operation of the remote contr
43. nfigure the parameters to comply with these rules too before using the PHANTOM 2 VISION Users in Mainland China can refer to RAMIE zs FHZJS A Max Height amp Radius Limits The Max Height amp Radius restricts the flying height and distance Configuration can be done in the PHANTOM 2 VISION Assistant Once complete your aircraft will fly in a restricted cylinder 2013 2014 DJI Innovations All Rights Reserved 35 PHANTOM 2 VISION SE moa Limits Distance Limits Length Units Distance Limits include Max height limit Meter Feet Mile and Max radius limit Max Height Radius Settings Distance Limits Flight Limits of SpecialArea Wnte values in the boxed of Max Height and Max Radius the aircraft will be restricted to fly in the green cylinder airspace shown in the figure Max Height 400m Max Height always works Max Radius Max works only in Ready to Fly status Only Throttle and Rudder commands Height are available if the aircraft rushes out of the limits and it will fy back towards Max Home point automatically Remote controller regains all controls once the aircraft is within the green airspace The Failsafe and the Ground Station functions are not affected by flight limits Referto user manual for more details Important Max Radius L 1500m Home Point The height of aircraft when it is powered on Default Ready to Fly 9 0000 The flight height is res
44. nter will appear in the top right corner of the preview screen Press again to stop recording 000 00 04 Distance 331 9ft Altitude 475 2ft Speed 0 2mph 12 Camera Settings Tap to open the camera settings menu refer to Camera Settings 15 Hide or Show Flight Parameters Tap to hide the flight parameters Tap again to show Camera Settings 1 Capture Mode ws L White Balance 2 Photo Size ee Exposure Metering 3 Video Resolution 8 Sea ko Exposure Compensation Sharpness 4 pes Photo Format 9 F4 d S 1 Lo Anti flicker 5 10 Ka 6 rr White Balance m s Restore Default Settings 7 OK Exposure Metering 12 To Format SD Card 1 Capture Mode m Single capture 5 captures 5 captures Timed capture Also selectable a Intervals between two shots 5 60 s b Number of shots 2 254 or infinite shots until Micro SD card is filled Capture Button will change according to the selected capture mode e ES ei I 2 Photo Size IB Large 4384 x 3288 4 3 14 4MP 2013 2014 DJI Innovations All Rights Reserved 44 Medium 4384 x 2922 3 2 12 8MP Small 4384 x 2466 16 9 10 8MP 3 Video Resolution 1920 x 1080 60i 16 9 1920 x 1080 30p 16 9 1920 x 1080 25p 16 9 1280 x 960 30p 4 3 1280 x 960 25p 4 3 1280 x 720 60p 16 9 1280 x 720 30p 16 9 640 x 480 30p 4 5 VGA Three Field of View FOV options a
45. oller The remote controller will blink the LED and sound an alert when the voltage drops below 5 9V and automatically power off after 5 seconds This process will repeat even if you power cycle the remote controller If this low voltage warning occurs during flight the remote controller will automatically power off causing the aircraft to enter Failsafe mode which cannot be interrupted refer to Failsafe Function section for details It is strongly recommended to replace batteries if the 3 9V 4 5V low voltage warning occurs 3 4 Antenna Orientation Try to keep the antenna pointing skyward perpendicular to the ground in order to achieve the maximum communication range during flight 2013 2014 DJI Innovations All Rights Reserved 9 The remote controller s antenna should be pointing skyward with no obstacles in the way Otherwise the Failsafe function may initialize prematurely during flight The Mobile Device and Range Extender should not block the antenna 5 5 Remote Controller Operation Definitions The stick neutral positions and stick released mean the control sticks of the remote controller are placed at the central position To move the stick means that the stick of remote controller is pushed away from the central position Remote Controller Aircraft Mode 2 au nose direction Operation details The throttle
46. ormatting 12 5 Album Page Camera SD CARD Album Browse thumbnails of photos and videos stored on the Micro SD card Tap to view photo or watch video 1 teda y 6 Photos 2 Videos EM 00 00 34 MERE Yesterday 7 Photos 1 Video 1 Photos and Videos are listed and grouped by date 2 All photos and videos that have already been synced to your mobile device are identified with the icon 3 Tap any thumbnail for single view mode Tap a Photo thumbnail that hasn t been synchronized to the mobile device to view the photo Swipe left or right to view the previous or next photo item Tap on a video thumbnail to play it and view the video s length A progress bar will also appear at the bottom of the screen Tapki to enter single synchronization mode to synchronize a single photo or video or to synchronize and play a video at the same time 4 Tap the buttone to enter multiple synchronization mode as shown in the following diagram Tap thumbnails to select photos or videos to synchronize to your mobile device The thumbnails identified by the check mark are 2013 2014 DJI Innovations All Rights Reserved 47 successfully selected Or you can select one or more groups to be synchronized by checking the box before the group and then Tap to start synchronizing During the synchronization process users can tap EJ to cancel the synchronization Photos and videos that have been synchronized to the mobile device will
47. ovations All Rights Reserved 22 7 Preparing the Flight Battery Before use please read and follow the user manual disclaimer and the warnings on the battery Users take full responsibility for all operations and usage 7 1 Intelligent Battery and Charger Instructions The intelligent battery is specially designed for the PHANTOM 2 VISION with a battery capacity of 5200mAh voltage of ll lv and charge discharge management functionality The battery should only be charged with the charger provided by DJI DJI does not take any responsibility for operation of any charger from a third party There are many features provided by the DJI charger Balance charge protection Full charge protection Short circuit protection Output protection Sleep protection Overheating protection Intelligent Battery Charger 7 2 Charging Procedures 1 2 Connect the battery to the charger while the power is OFF Connect the charger to a wall socket The charger indicator light will turn a solid red when it is charging Wait until the charger indicator turns solid green to which indicates that the battery is completely charged Charger indicator Status of charge 2013 2014 DJI Innovations All Rights Reserved 23 7 3 Install the Battery Push the battery into the battery compartment correctly as the following diagram shows Make sure to push the battery into the compartment until you hear a click sound
48. pitch downwards Green slider indicates current camera pitch Normal Mode pitch control Pitch movement s Accelerometer Sensor Mode Tap and Hold to switch on Accelerometer Sensor Mode to control camera pitch and rotation by moving your mobile device Tilt device forward to pitch camera downward and backward to pitch upward Lean it left to rotate vn and right to rotate right Mb heee IE e 0 T In Accelerometer Sensor Mode the pitch angle indicator will show a grey area When the green pitch indicator is inside the grey area the camera will move according to pitch gestures When the indicator reaches the boundary of the grey area pitch gestures will control the camera s pitch speed at a constant rate 5 Flight Attitude and Radar Function 2013 2014 DJI Innovations All Rights Reserved 41 Flight attitude is indicated by the flight attitude icon 1 The red arrow shows which direction the PHANTOM 2 VISION is facing 2 Blue and brown areas indicate its pitch 3 Tilting of the brown and blue area shows roll angle Tap the flight attitude icon to turn on the radar function Home is located in the center of the radar and the red icon indicates the PHANTOM 2 VISION s current heading direction and approximate distance from home Tap the flight attitude icon again to disable the radar PHANTOM 2 VISION Home Point Mobile Device Location Distance
49. pp can work normally on the second mobile device 14 11 How to land the aircraft smoothly in a better way First pull the throttle stick position down to lower than 596 then execute the CSC command to stop the motors 14 12 Why the discharge times of a new battery not at zero A battery aging test is performed prior to delivery which affects the discharge time of the new battery This is why the discharge time of a new battery is not zero The battery is okay to use 2013 2014 DJI Innovations All Rights Reserved 61 15 Appendix LED Flight Indicator Status Normal status Power On Self Test Warming Up Ready to Fly Ready to Fly non GPS Warning and Error Remote Controller Signal Lost 1 Level Low Battery Capacity Warning 2nd Level Low Battery Capacity Warning Not Stationary or Sensor Bias is too big Error Compass Needs Calibration LED Flight Indicators LED Flight Indicators You can figure out the error by connecting the PHANTOM 2 VISION to the PHANTOM 2 VISION s Assistant Software 2013 2014 DJI Innovations All Rights Reserved 62 Specifications Aircraft Supported Battery PHANTOM 2 VISION Weight Hovering Accuracy Ready to Fly Max Yaw Angular Velocity Max Tiltable Angle Max Ascent Descent Speed Max Flight Speed Wheelbase Tilting Range of Gimbal Remote Controller Operating Frequency Communication Distance open area Receiver Sensitivity I PER Transmitting Power EIRP Workin
50. r right click the icon using a mouse Choose Open from the shortcut menu click Open in the prompt dialog box and then software will launch After the first successful launch direct launching of the software can be achieved by double clicking the PHANTOM 2 VISION icon in the Finder or using Launchpad 2013 2014 DJI Innovations All Rights Reserved 54 DJI PHANTOM 2 VISION Basic Mounting Aircraft Advanced Motor GPS Location Mixer Type Quad rotor X Motor Idle Speed Recommended Cut Off Type Intelligent X Dem Rc Y Ocm Z Dom Receiver Type D Bus F S Failsafe Methods Landing Gain Pitch Roll Yaw Vertical IOC Intelligent Orientation Control OFF Basic 120 120 120 120 Attitude 200 200 Gimbal Channel Monitor Gimbal Switch LU Battery uU EEREHEHEHEE TEE EEUU Current Voltage 12517mV 34 Current Capacity 9896 First Level Warning 3096 Second Level Warning 1596 OnLine Help A Installer in DMG format supports only Mac OS X 10 6 Lion or above E A Usage of PHANTOM 2 VISION Assistant Software on Mac OS X and Windows are exactly the same The Assistant Software pages appear in other places of this manual are on the Windows for example 13 2 Using the PHANTOM 2 VISION Assistant Software on a PC l Start up the PC power on the PHANTOM 2 VISION then connect the PHANTOM 2 VISION to the PC with a Micro USB cable DO NOT disconnect until configuration
51. re supported when shooting in 1920x1080 60i 1920x1080 30p and 1920x1080 25p Wide 140 Medium 120 and Narrow 90 4 Photo Format IS JPEG RAW The PHANTOM 2 VISION camera shoots in JPEG and RAW file formats simultaneously when this option is selected See the following table for detailed specifications JPEG photo size 4584 X 5288 4584 X 2922 4384 X 2466 RAW photo size 4584 X 5288 4584 X 2920 4584 X 2464 RAW is not supported in continuous capture mode or timed capture mode JPEG photos will be created automatically RAW format support will be coming soon with DJI Conversion Software to convert PHANTOM 2 VISION s Camera RAW files to Adobe DNG 5 Selectable ISO AUTO 100 200 400 2013 2014 DJI Innovations All Rights Reserved 45 6 White Balance 8 Exposure Compensation 9 Sharpness 10 Anti flicker AWB auto Sunny Cloudy Indoor Center Average Spot 2 0 EV 1 7 EV 13 EV 1 0 EV 0 7 EV 0 3 EV O EV Standard Hard Soft Auto 5OHz 60Hz 20 EV 17 EV 1 3 EV 1 0 EV 07 EV 0 3 EV 11 Restore Default Settings Restores all camera default settings Camera reboot is needed to allow restoration to take effect 2013 2014 DJI Innovations All Rights Reserved 46 12 Format SD Card Format the Micro SD card All data stored in the Micro SD card will be lost after formatting Remember to backup before f
52. remain A Some mobile devices may fail to support synchronization of 1080i60O video files SD CARD Cancel 5 Select a group Today 6 Photos 2 Videos Yesterday 7 Photos 1 Video Select a single photo or video SD CARD wl Today 6 Photos 2 Videos wv Oct 2013 118 Photos 8 Videos Yesterday 7 Photos 1 Video 5 Tap Cancel or Finished to exit the multiple synchronization mode and return to the SD CARD page Mobile Device Album LM 2 R 1 m vd T l You can browse all photos and videos in the album which have been synchronized to the mobile device view a 1 Li 37 Photos 2 Videos selected photo or play a selected video 2 Photos and videos are listed in thumbnail style and sorted by capture time 2013 2014 DJI Innovations All Rights Reserved 48 5 Pictures and videos are sorted by captured recorded Geo tagged locations A Access to the Internet is required to load a map A ss 9 A Ch bs 3 Ka Geo tagged locations 4 Tap any thumbnail for single view you can slide left or right to view the previous or next photo Tap a video thumbnail to play a single video 5 Tap to share your photos and videos to social network sites A Access to the Internet is required to share your photos and videos SHARING 12 4 News Page View the latest DJI news Internet access is required 2013 2014 DJI Innovat
53. stick controls the aircraft elevation Push the stick up and the aircraft will rise Pull the stick down and the aircraft will descend The aircraft will automatically hover and hold its height if the sticks are centered Push the throttle stick above the centered neutral position to cause the aircraft to take off We suggest that you push the throttle stick slowly to prevent the aircraft from sudden and unexpected elevation The yaw stick controls the aircraft rudder Push the stick left and the aircraft will rotate counter clock wise Push the stick right and the aircraft will rotate clock wise If the stick is centered the aircraft will always fly in the same direction 2013 2014 DJI Innovations All Rights Reserved 10 The command stick controls the rotating angular velocity of the aircraft Increasing movement of the command stick results in faster aircraft rotation velocity The pitch stick controls the aircraft s front amp back tilt Push the stick up and the aircraft will tilt and fly forward Pull the stick down and the aircraft will tilt and fly backward The aircraft will keep level and straight if the stick is centered Increasing movement of the command stick will result in a larger tilt angle maximum is 35 and faster fli
54. t has entered into Failsafe mode refer to Failsafe Function for details A low battery capacity warning is indicated by the LED flight indicator blinking red slowly or rapidly during flight Refer to the Low Battery Capacity Warning Function for details Watch the quick start video about flight for more flight information 11 4 Failsafe Function The aircraft will enter Failsafe mode when the connection from the remote controller is lost The flight control system will automatically control the aircraft to return to home and land to reduce injuries or damage The following situations would make the aircraft fail to receive a signal from the remote controller and enter Failsafe mode 1 The remote controller is powered off 2 The aircraft has flown out of the effective communication range of the remote controller 3 There is an obstacle obstructing the signal between the remote controller and the aircraft essentially reducing the distance the signal can travel 4 There is interference causing a signal problem with the remote controller Failsafe works differently depending on the mode the aircraft is in when Failsafe mode is initiated whether it is in the Ready to Fly or Ready to Fly non GPS mode Ready to Fly non GPS Automatic landing The flight control system will try to keep the aircraft level during descent and landing Note that the aircraft may be drifting during descent and landing process Ready to Fly Au
55. th CE and FCC see the FCC ID regulations and is set to Mode 2 before delivery The compliance version can be configured by twisting the potentiometer knob on the back of the remote controller The stick configuration can also be reset in the PHANTOM RC Assistant Software Please refer to lt PHANTOM RC Assistant and Compliance Configuration for details 1 CE compliant devices have an effective communication range of 500 meters in open spaces due to power limitations Be sure to watch your fight distance as the PHANTOM 2 VISION will enter Failsafe mode auto landing or go home and land if it flies beyond this range FCC compliant devices have an effective range of 500 meters in open spaces Be sure to watch your fight distance as the PHANTOM 2 VISION will enter Failsafe mode auto landing or go home and land if it flies beyond this range Pay attention to and follow local laws and regulations Antenna Carrying Handle Switch SI Switch S2 Reserved Joystick J1 Roll left amp right J2 Pitch front amp back Joystick J3 Throttle up amp down J4 Yaw rotation Neck Strap Attachment Power Switch Power Indicator Battery Compartment On the back 3 2 Power on the Remote Controller l Install the four AA Batteries not included into the battery compartment on the back of the remote controller according to the
56. tomatic go home and land The flight control system will automatically control the aircraft to fly back to the home point and land 2013 2014 DJI Innovations All Rights Reserved 32 Home Point When the aircraft is initializing the Ready to Fly status the aircraft will record the current GPS coordinates as the home point It is recommended to lift off only after Ready to Fly status is confirmed for the safety of being able to fly back to home point successfully in case the Failsafe mode is initiated Go Home Procedures Record Home Point 2 Flying 3 Remote controller signal lost Ze es uw 9 e 7 e LED Flight Indicator 00005900000 LED Flight Indicator 9 9 LED Flight Indicator oo O 9 4 Signal lost lasts 5s begin to go home 5 Fly back to home point Landing after hovering 15s 7 Y Height over home point gt 20m p go S PPP TAR 20 Elevate to 20m AT An m agp OK k d al ms e mm Height over home point lt 20m SG LED Flight Indicator Co 00606 ED Flight Indicator BOO 00A LED Flight Indicator 08000400 In a Failsafe situation if less than 6 GPS satellites are found for more than 20 seconds the aircraft will descend automatically In Phantom 2 Vision mode users can set a new home point manually when the aircraft is in Ready to fly status as long as a home point has been recorded automatically Quickly flipping the S2 switch of the remote controller from upper most to lower most positions
57. tricted to fly under the max Max Height None height The flight distance is restricted to fly within the max Rapid red flashings C when Max Radius radius close to the Max radius limit Ready to Fly non GPS 9 0000 Im Flight Limits Rear LED flight indicator The flight height is restricted to fly under the minor Max Height None height between the Max height and 120m Not limited and no LED indicators i 1 If the aircraft flies out of the limits you can still control your aircraft except to fly it further away 2 If the aircraft is flying out of the max radius in Ready to Fly non GPS status it will fly back within the limits range automatically if 6 or more GPS satellites have been found 11 7 Flight Limits of Special Areas Special areas include airports worldwide All special areas are listed on the DJI official website Please refer to http www dji com fly safe category mc for details These areas have been divided into category A and category B 2013 2014 DJI Innovations All Rights Reserved 36 8100m g b N Center of 8000m Special Area 10 5m Category A kb A R Ready to Fly mode A Orange Limits Motors will not start If the Phantom flies into a special area in Ready to Fly non GPS mode and Ready to Fly mode activates it will automatically descend and land then stop its motors If the Phantom flies into a special area in Ready to Fly non GPS mode and Ready to Fl
58. troller s mid point is set Refer to lt How to solve large margin s mid abnormally point error 2013 2014 DJI Innovations All Rights Reserved 27 9 Connecting to the Camera 9 Camera Connection Procedures Please carry out the following procedures to connect a mobile device to the PHANTOM 2 VISION IL Power on the remote controller and the range extender 2 Make sure the switch on the back of the camera is set to WIFI ON and then power on the PHANTOM 2 VISION 3 Fig l Enable the Wi Fi on your mobile device wait for about 30 seconds and then select the Phantom_xxxxxx from theWi Fi network list 4 Fig 2 Run the DJI VISION App on your mobile device which will indicate the current Wi Fi connection status on the main menu The Wi Fi connection indicator will turn solid green which means the connection is good 5 Tap the CAMERA icon and the DJI VISION App will establish a live camera preview Fig 3 This means everything is now functioning Enable the Wi Fi Wi Fi H Wi Fi Connection Choose a Network Indicator FC200 000539 A 1 Select Phantom xxxxxx Phantom 100020 e Other gt CAMERA ALBUM Ask to Join Networks OFF Known networks will be joined automatically If no Known networks are available you will have to manually select a network NEWS SETTINGS Fig l Fig 2 we Distance 332 0ft Altitude 476 0ft Speed 0 0mph Fig 3 2013
59. urrent version of the DJI VISION App and also for contact information 2013 2014 DJI Innovations All Rights Reserved 53 13 Assistant Software Installation and Configuration 13 1 Installing Driver and PHANTOM 2 VISION Assistant Software Installing and running on Windows Download driver installer and Assistant Software installer in EXE format from the download page of PHANTOM 2 VISION on the DJI website Connect the PHANTOM 2 VISION to a PC via a Micro USB cable Run the driver installer and follow the prompts to finish installation Next run the Assistant Software installer and follow the prompts to finish installation Double click the PHANTOM 2 VISION icon on your Windows desktop to launch the software The installer in EXE format only supports Windows operating systems Win XP Win7 Win8 32 or 64 bit Installing and running on Mac OS X Download the Assistant Software installer in DMG format from the download page of PHANTOM 2 VISION on the DJI website Run the installer and follow the prompts to finish installation cJ DJI Assistant for Mac When launching for the first time if use Launchpad to run the PHANTOM 2 VISION Assistant Software Launchpad won tallow access because the software has not been reviewed by Mac App Store Phantom can t be opened because it is 4 from an unidentified developer kak Locate the PHANTOM 2 VISION icon in the Finder press the Control key and then click the icon o
60. ut 9443 Black Nut 9443 R Diagram Attach to the motor thread that does Attach to the motor thread that has a Assembly Location not have a black dot black dot Fastening Un fastening 85 Lock Tighten the propeller in this direction Instructions H Unlock Remove the propeller in this direction 1 2 Assembly l Fig l Remove the four warning cards from the motors after you read them 2 Fig 2 Prepare the two grey nut propellers and two black nut propellers Make sure to match the black nut propellers with the correctly marked black dot motors Tighten the propellers according to the fastening Instructions SEN Fig 2 Fig 1 3 Removing the Propellers Fig 5 Keep the motor deadlocked in place with the assistant wrench or one hand and remove the propeller according to the un fastening instructions 1 4 Notes Propellers are self tightening during flight DO NOT use any thread locker on the threads Make sure to match the propeller nut colors with the corresponding motors It is advised to wear protective gloves during propeller assembly and removal Check that the propellers and motors are installed correctly and firmly before every flight Check that all propellers are in good condition before flight DO NOT use any ageing chipped or broken propellers To avoid injury STAND CLEAR of and DO NOT touch the propellers or motors when they are spinning ONLY use original DJI propellers for a better and safer
61. wi K Sounds gt t o Ej Facebook gt tos Brightness amp Wallpaper gt e Sina Weibo gt iCloud gt 14 8 Failure to share Solution Please make sure the mobile device has access to the Internet 14 9 Some mobile Android devices have a problem connecting to the PHANTOM 2 VISION Wi Fi Extender Solution Some mobile Android devices do not allow for both a Wi Fi connection and a mobile data connection at the same time When trying to connect to the PHANTOM 2 VISION Wi Fi network most devices will check whether an Internet connection has a certain Wi Fi setting enabled e g Auto network switch or Test for Internet connection If no Internet connection is found because the PHANTOM 2 VISION creates a non routable connection it will drop the PHANTOM 2 VISION Wi Fi network connection and scan for the next available connection Example For the Samsung Note 3 carry out the following procedures to solve this issue Tap Settings gt Wi Fi and then tap the Menu button Select Advanced then uncheck the Auto network switch You might see a warning that indicates the Internet connection is unstable but just ignore this message 2013 2014 DJI Innovations All Rights Reserved 60 14 10 Usage tips for the App used on multiple mobile devices During flight if you use the App on multiple mobile devices please turn off the App on the first mobile device and then turn on the App on the second one to ensure the A
62. y mode activates it will descend to airspace C and hover 5 meters below edge d B Yellow No restrictions of flight but the Phantom will not enter Category A the aircraft can fly free but it will not enter Airspace B through Boundary 6 amp d Around Category B sites the phantom can fly freely but it will not enter into Airspace A through Boundary a Airspace A B C D Boundary b a d bc Center of Special Area Airspace A C D Boundary a c a a C Category B Rear LED DJI VISION App Flight Indicator Warning You are in a restricted zone Take off prohibited Warning You are in a restricted zone Now descending Warning You Are In A Restricted Zone Now Descending Warning You are close to a restricted zone Fly Cautiously Note For airspace A when aircraft enters the area beneath the boundary d the warning message changes to You are in a restricted area Max flight height restricted to between 10 5m and 120m Fly Cautiously 2013 2014 DJI Innovations All Rights Reserved 37 Semi automatic descent All stick commands are available except the throttle stick command during the descent and landing process Motors will stop automatically after landing Users must toggle the S switch to regain control This is the same as regaining control during Failsafe Refer to Regaining Control During Failsafe Procedure on page 55 for more details 1 When flying in t

Phantom 2 Vision User Manual (EN) v1.16

Contents

Download Pdf Manuals

Related Search

Related Contents