Home

Din Rail Universal Module 8 inputs / 8 outputs

1. 6 Input Dimming W 1 1 1 1088E01KNX x General Parameter Configuration Input 1 Input Configuration Input 1 S Output Configuration Function hd Output 1 Relay ON OFF Output 2 Relay ON OFF Contact Type Normally Open D Output 3 Relay ON OFF Output 4 Relay ON OFF Dimmer Command Brighter Darker D Output 5 Relay ON OFF Output 6 Relay ON OFF Dimming Step Maximum Minimum Brightness D Output 7 Relay ON OFF Output 8 Relay ON OFF Minimum time for long press operation fi Sec DI Through the dimming function it s possible to control a light dimmer using short amp long press of a push button connected to the input channel Each input uses 2 communication objects e 1 bit dimension for ON OFF command associated to short press operation e 4 bit dimension for brightness regulation associated to long press operation KNX PARAMETER SETTINGS SES See paragraph 4 ee e Brighter Dimming Command e Darker e Brighter Darker e Brighter on short operation telegram 1 ON is sent to the bus on long operation telegram increase brightness is sent to the bus e Darker on short operation telegram 0 OFF is sent to the bus on long operation telegram decrease brightness is sent to the bus e Brighter Darker on short or long operation telegrams ON OFF and telegrams increase decrease brightness are sent alternatively A Max brightness Min Brightness 1 2 Brig
2. Electric Valves Output Ge Electric Valves Output Motor Reduction Driver Channels El Valves Dut and Mot Reduc Ch KNX PARAMETER SETTINGS e Disabled All Valve Closed e Enabled e Electric valves output All Valve Closed Function depends on e Motor reduction Driver Channels e Electric valves output and Motor reduction Channels See paragraph 15 4 Function VALVES ALL CLOSED 3 2 Communications Objects Das lt Electric valves Motor Reduction Driver gt All Yalye Closed 1 bit CR T Dan Device On Line 1 bt CR T 8 64 Eelectron SpA Via Magenta 77 22 1 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato A Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 K x 1088BO1KNXFI01010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook 4 Input lt x gt Configuration For each of the 8 input channels present on the device the selections are made through a configuration page 1 1 1 IOBBEOIKNX General Parameter Configuration Input Configuration Output Configuration Function Output 1 Relay ON OFF Output 2 Relay ON OFF Contact Type Output 3 Relay ON OFF l Output 4 Relay ON OFF Action Output 5 Relay ON OFF Output 6 Relay ON OFF Value on push Output 7 Relay ON OFF Output 8 Relay ON OFF Value
3. 7 2 Communications Objects For every input channel configured as Shutter and Blind two different communication objects are used as shown below Number Name Object Function Length E R W T U G33 lt Input 1 gt Shutter Movement Up Down 1 bit C R W T G34 lt Input 2 gt Shutter Movement Up Down 1 bit C R W T Gass lt Input 3 gt Shutter Movement Up Down 1 bit C R W T G36 lt Input 4 gt Shutter Movement Up Down 1 bit C R W T E37 lt Input 5 gt Shutter Movement Up Down 1 bit C R W T Ejs lt Input 6 gt Shutter Movement Up Down 1 bit CRWT G39 lt Input gt Shutter Movement Up Down 1 bit C R W T Dan lt Input 8 gt Shutter Movement Up Down 1 bit C R W T 41 lt Input 1 gt Stop Step Stop Step 1 bit CR T Ejaz lt Input 2 gt Stop Step Stop Step 1 bit CR T Dis lt Input 3 gt Stop Step Stop Step 1 bit CR T 44 lt Input 4 gt Stop Step Stop Step 1 bit CR T Du lt Input 5 gt Stop Step Stop Step 1 bit CR T G46 lt Input 6 gt Stop Step Stop Step 1 bit CR T 47 lt Input 7 gt Stop Step Stop Step 1 bit CR T Dis lt Input 8 gt Stop Step Stop Step 1 bit CR T 16 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 D0C C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato a Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 K N x 1088B01KNX
4. Name Object Function Lenth f ciri w lt fu Has lt Input 1 gt Led Blinking OfF Blinking 1 bit C R W 34 lt Input 2 gt Led Blinking OfF Blinking 1 bit C R W Gass lt Input 3 gt Led Blinking OfF Blinking 1 bit C R W se lt Input 4 gt Led Blinking OFF Blinking 1 bit C R W Da lt Input 5 gt Led Blinking OFF Blinking 1 bit C R W Ejas Input 6 gt Led Blinking Off Blinking 1 bit CRW Daa lt Input 7 gt Led Blinking OfF Blinking 1 bit C R W Dan lt Input 8 gt Led Blinking OFF Blinking 1 bit C R W 20 64 Eelectron SpA Via Magenta 77 22 1 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato gt e Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 K N x 1088BO1KNXFI01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 10 Output Configuration Wi 1 1 1 1088E01KNX x General Parameter Configuration Output Configuration Input Configuration Dutput Configuration R Output 1 Relay ON OFF FAN COIL ACTUATOR Output 1 2 3 4 5 Disable 7 Output 2 Relay ON OFF Output 3 Relay ON OFF Output 4 Relay ON OFF Output 5 Relay ON OFF Output 1 2 Configuration Output are independent DI Output 6 Relay ON OFF Output 7 Relay ON OFF Output 1 Configuration Generic Load Control DI Output 8 Relay ON OFF O
5. Output 1 Relay ON OFF Output 2 Relay ON OFF Output 3 Relay ON OFF Output 4 Relay ON OFF Output 5 Relay ON OFF Output 6 Relay ON OFF Output 7 Relay ON OFF Output 8 Relay ON OFF Input 1 Function Distant d Contact Type Nomaly Opn sl Action Short and Long Press Minimum time for long press operation ise Additional object for long press Dises Value on short press ON Me Value on long press OFF By selecting parameter Action with value Short Long it s possible to send to the bus 2 different telegrams according with the type of action done on the input channels one for short press and another for long press 11 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 1088B01KNXF101010002 D0C a KNX 1088B01KNXF1I01010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook KNX PARAMETER SETTINGS Contact type See paragraph 4 0 3 Sec 0 4 Sec 0 5 Sec 06 Sec 0 8 Sec j 1 2 Sec Time for long operation 15 Sen 2 Sec 2 5 Sec 3 Sec 4 Sec 5 Sec 6 Sec 8 Sec 10 Sec Determines how long must be a press to be considered long if shorter than the selected value the press will be considered short e Disable Addition
6. unlock condition e Valve Open Valve Position when Lock is Active e Valve Close This parameter selects the state the valve must assume when the lock function becomes active See note 2 Valve Open Valve Close Keep previous state and ignore telegrams Keep previous state and don t ignore telegrams Position when Lock Ends 49 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato gt i A Tribunale di Milano 359157 8760 07 i CCIAA Milano 148549 K X 1088B01KNXF101010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook e Valve Open valve open position See note 2 e Valve Close valve closed position See note 2 e Keep previous state and ignore telegrams Relay returns in the state it was before lock function became active e Keep previous state and don t ignore telegrams the output channel returns to its condition prior to the activation of the block unless you have received a telegram on the switch object or scenario in this case the last command received is executed NOTES 1 If the parameter Initial Value for Lock Object has the same value of Telegram for Lock Activation happens that on power up the output channel sta
7. 8 Output Module Product Handbook Warning Function Telegram NO is closed Contact type NO NO is open Switch off time _______ly i Warning Time gt Send ON when Timing is Active Trigger Mode DI Ignore Relay Feedback T rigger Mode Extension Mode Maximum Number of Time Extension 4 times hz KNX PARAMETER SETTINGS e Ignore Send ON when Timing is active e Trigger Mode e Extension Mode This allows you to set the behaviour of the device when it receives a ON command while the staircase timing is running e Ignore On receiving a ON command the device ignores it and goes on executing the timing e Trigger Mode On receiving a ON command the device restart the stairs light time execuiting the whole time again e Extension Mode On receiving the command the device extends the stairs light time increasing it by the time of the standard stairs light time Note that the extension option does not reset the timing but it changes its duration and becomes a multiple of the set stairs light time The maximum number of extension is allowed by the parameter Maximum numbert of Time Extension 36 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 AE sarees EN CCIAA Milano 148549 K X 1088BO1KNXFI01010002 DOC O eceleciron
8. lt Input 8 gt Off On Dimmer off on 1 bit CR WT 14 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato eo Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 K x 1088B01KNXF1I01010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook 7 Input Shutter and Blind Ml 1 1 1 1088E01KNX q xj General Parameter Configuration Input 1 Input Configuration Input 2 Function Shutter and Blind DI Input 3 Input 4 Contact Type Normally Open Input 5 Input 6 Shutter Command Move Up Move Down e Input 7 Input 8 Minimum time for long press operation h Sec v Output Configuration Output 1 Relay ON OFF Output 2 Relay ON OFF Output 3 Relay ON OFF Output 4 Relay ON OFF Output 5 Relay ON OFF Output 6 Relay ON OFF Output 7 Relay ON OFF Output 8 Relay ON OFF Through the Shutter and Blind function it s possible to control Roller Shutters or Blinds using short amp long press of a push button connected to the input channel Each input uses 2 communication objects e 1 bit dimension for STEP STOP command associated to short press operation e 1 bit dimension for UP DOWN command associated to long press operation KNX PARAMETER SETTINGS Contaci ype See paragraph 4 e Move UP e Move Dow
9. 3 Louvres automatic movement AEN 55 14 4 Additional ETC 55 E SE FUN AK 56 14 6 Lock Function wwwwmmmemimimimmwwmiwi wima tcacecabseacousL eG coenkeacaanacncsmabenieae 57 t4 Alarmi EN DEE 58 14 8 Shutter position after lock and aam 59 14 9 Priority table for communication oblecls mimi 59 2 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 AE sarees eer CCIAA Milano 148549 K X 1088BO1KNXFI01010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook 15 Output Configuration for motor reduction driver ccccccccccccceceeeceeeceeeeeeeeeeeeeeeeeeeeeess 60 15 2 Main Parameters Aa 61 15 3 Lock FUNCTION aa 63 15 4 Function VALVES ALL CLOSED EE 64 gt Any information inside this manual can be changed without advice gt This handbook can be download freely from the website www eelectron com gt Exclusion of liability Despite checking that the contents of this document match the hardware and software deviations cannot be completely excluded We therefore cannot accept any liability for this Any necessary corrections will be incorporated into newer versions of this manual 3 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P
10. Din Rail Universal 8 Input 8 Output Module Product Handbook Duration of relay timing is re trigge able Telegram 1 1 NO close Normally Open NO open NO close Normally Close NO open Extension Mode Telegram 1 1 1 NO close Normally Open NO open 37 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato gt i A Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 K x 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 12 8 Function Continuous Switching In this configuration it is possible to activate the relay to perform a continuous ON OFF switching that can be started or ended by a specified activation telegram Ton and Torr can be set by parameters Output 1 Relay ON OFF Contact Type JNO Normally Open DI Additional Function No Function Activation Telegram Telegram sl Function Continuous Switching sl Time ON Base Time sl Time ON Factor A Time OFF Base Time Daer sl Time OFF Factor KR D Start Continuous Switching on Power Up Fase tt sl KNX PARAMETER SETTINGS e 1 sec Time ON Base Time e 1 minute e 1 hour Time ON Factor 1 255 The duration time of the ON stat
11. IVA 11666760159 Capitale sociale 250 000 00 interamente versato eae ji Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 K x 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 1 General Introduction This manual is intended to be used by installers and describes functions and parameters of the device IO88E01KNX Din Rail 8 In 8 Out Module and how is possible to change settings and configurations using ETS software tool 2 Product and functional overview The 1O88E01KNX module is designed to be installed on a DIN rail and to be used in Home and Building installations i e offices hospitals hotels private houses etc The device is equipped with 8 binary inputs potential free and 8 binary relay outputs Inputs can be connected to conventional switching devices e g push buttons switches floating contacts for switching functions with pulse edge evaluation e g rising or falling edge toggle etc Inputs can be configured with ETS SW as output channels to drive LED in synoptic monitoring panels Input main functions Load activation deactivation commands ON OFF TOGGLE with short press or with differentiation of long and short action Sending of long action telegrams on the same address of short action or on a different group address Dimmer management with single or double push button Blind Roller Shutter management with sing
12. Rail Universal 8 Input 8 Output Module Product Handbook Example of control with the control value of 50 Valve open Valve closed TC Cycle Time Example of control with the control value of 80 Valve open Valve closed TC Cycle Time 2 the device has to accumulate the energy it needs to switch the relays during the power on phase and stores it into capacitors For this reason when a power down is detected the device has the energy to switch all the 8 relays only if it has been powered from at least 60 seconds and it has not done a full 8 relay switch from at least 20 seconds It is strongly recommended not to select a full 8 relay switch on power down because the full switch cannot be always be done 3 When is selected the value STOP no movement for the parameter Behaviour on power up it is maintained the state selected on power down unless you have selected on power down the behaviour STOP no movement in that case it is maintained the state active before power down 48 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato aa Tribunale di Milano 359157 8760 07 KR CCIAA Milano 148549 K X 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module
13. add a maximum of 13 group addresses of this kind for the whole device 5 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DO0C C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato ream CCIAA Milano 148549 Tribunale di Milano 359157 8760 07 K x 1088B01KNXF1I01010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook 3 General Parameter Configuration 3 1 Parameters MM 1 1 1 1088E01KNX x General Parameter Configuration General Parameter Configuration Input Configuration Output Configuration el Output 1 Relay ON OFF Delay on Power up 3 15 sec 3 el Output 2 Relay ON OFF Output 3 Relay ON OFF Debouce Time for Inputs eo ms w Output 4 Relay ON OFF Output 5 Relay ON OFF Send device ON LINE Enabled Me Output 6 Relay ON OFF Output 7 Relay ON OFF Device ON LINE sending time z Output 8 Relay ON OFF If is activated at least one Electric Valve or Motor Driver All Valve Closed Disable D Cancel Default Info Help ZA General Parameter Configuration Page list generic parameters which affects all input output channels or their selection applies to all contacts of the input device simultaneously regardless of the function selected later for each KNX PARAMETER SETTINGS Delay on Power up 3 15 sec 2 15 second
14. bus Delay on ventilation start min 1 15 This parameter has effect only in heating mode and introduces a time delay between the reception of a command which starts the fan speed and the real starting time in order to avoid to blow cold air instead of warm due to the fact the hydraulic system need a certain time to supply the hot fluid to the fan coil The delay however is introduced only when the fan coil actuator activates one of his speeds starting from the state of no active speed S1 S2 S3 are all off 25 64 Eelectron SpA Via Magenta 77 22 1 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 SE eer CCIAA Milano 148549 K x 1088BO1KNXFI01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook Wi 1 1 1 1088E01KNX xj General Parameter Configuration Fan Coil Actuator Input Configuration Dutput Configuration pe Dien H Output 6 Relay ON OFF eld SE Output 7 Relay ON OFF p S s S a Output 8 Relay ON OFF Relay State when Valve is Deactivated Relay is Open when Valve is Deactivated be Delay between Speed Changes sec fi Object Type for Speed Command fi x 1 Byte object D Limit Value Speed 2 3 70 v Limit Value Speed 1 2 30 e Lower Limit Value 0 DG Object Type for Speed Status fi x 1 Byte object D Delay on ventilation start min Jo gt Sending stat
15. defined state and force it to maintain this state even if the object switching value changes The behaviour of the lock function is the same described in par 12 11 Lock Function This function can be enabled or with 1 bit commands than with 1 byte commands KNX PARAMETER SETTINGS e Value 0 Initial Value for Lock Object SE e Value 1 This parameter selects the value of the lock object after a power on appropriately changing this value it is possible to start the output channel related to the lock function as locked or unlocked See note 1 e Telegram 0 Telegram for Lock Activation e Telegram 1 This parameter selects the values associated to the lock or unlock condition e Valve Open Valve Position when Lock is Active e Valve Close 63 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato gt a A Tribunale di Milano 359157 8760 07 R CCIAA Milano 148549 K X 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook This parameter selects the state the valve must assume when the lock function becomes active See note 2 e Valve Open e Valve Close Position when Lock Ends e Stop no movemen
16. ee 15 7 2 Communications Objects kee 16 8 Input Scene Management ee eeeeeccecceeceeeeeeeeeenaaeeeeeeeeeeeeeaaaaaaeeeeeeeeeeeessnaaeeeeeeeees 17 8 2 Communications ObJeCEtS wwwwwwmmmmwmwmamimi mimi mumw uwiii wawi 18 NEE AYA EE 19 9 1 Communications ODJEC S Aaa 20 10 OQutp t UA Aa 21 11 Output Configuration Fan Coil Achiaior imamu 23 11 2 STE ee ee 24 11 3 Control of Heating Cooling VAlVE wwwwmmmamamemiwimimimumaw geed etedetedeans 24 11 4 Fan Coil Speed E rue eects tt escalate es 25 12 Output Configuration for Generic Load Control 27 12 2 General PAPA ter Sa eegdesgebegeeggegeuieeECd gege Regen 28 12 3 REFU rieien coats oles cece es EAEE EE EEEE le EERE 29 12 4 Additional Functions ts cc ccccrecececersenconipececacehsenc seer tchencebseadsoet Seheacenseaceneacaenenemaielt 30 12 5 iere bei Eeer ta ea eee 31 12 6 Function ON OFF te 32 12 7 Function ON with delay timing OFF tee eae eek 33 12 8 Function Continuous Switching wwwwmmmamemimimumumawanitimimizamw iia 38 12 9 Communication oblechs seen 39 12 10 Logic ET Le EE A0 E D e ele E 41 12 12 Scene FUNCION aa 42 13 Output Configuration for Electric Valve Control ENEE 44 ES a 45 13 3 Lock PUI QUOI E 49 14 Output Configuration for shutter and DINS 222 ccc0ecccccetcceeeenetenccecesteenenenenenccebecenens 51 14 2 General Parameters 22 sce aesicden co A ioetieeitaeee shee ek ee 52 14
17. happens that on power up the output channel starts in lock mode waiting for a unlock telegram in order to become active Note that even if the relay starts with lock function already active it does not go automatically in the position defined by the parameter Relay Position when Lock is Active because this behaviuor is determined only by the parameter Behaviour on power up 2 The activated and deactivated conditions for each output channels correspond to ON or OFF condition upon the settings made for the Contact Type parameter 12 12 Scene Function General Parameter Configuration Output 1 Relay ON OFF Input Configuration Output Configuration Output 1 Relay ON OFF Contact Type NO Normally Open z lt Output 1 gt Scene E s Output 2 Relay ON OFF Additional Function No Function Output 3 Relay ON OFF Output 4 Relay ON OFF Activation Telegram Telegram 1 X Output 5 Relay ON OFF Output 6 Relay ON OFF Function ON OFF sl Output 7 Relay ON OFF Output 8 Relay ON OFF Relay Feedback When status change Telegram value for status sending Telegram 0 when output is OFF z Scene Enabled Behaviour on power down Stop no movement z Behaviour on power up Keep status before power down DI 42 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 1166676
18. important to determine a correct value of the parameter debounce time to avoid these bounces could be taken by the device as input switching How this parameter works after the device has detected a change of status for an input channel it waits for a time equal to the time set as debounce time before updating the value of the corresponding data point The input signal is not evaluated during this time This parameters affects all 8 device input channels TI fill Edge detected KNX PARAMETER SETTINGS e Disabled Send Device ON LINE Enabled 1 min 10 min 30 min 1 hr 2 Hr 12 Hr e 24Hr Device ON LINE sending time Through this parameter it s possible to enable a cyclical sending on the bus of a 1 bit telegram with value 1 this sending has a programmable time interval This message can be used to detect errors like power failure or breakage of the device to a monitoring system or to a bus control system 7 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 AE sarees eer CCIAA Milano 148549 K X 1088BO1KNXFI01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook If is activated at least one Electric Valve or Motor Driver All Valve Closed Enabled Sy All Valve Closed Functions depends on
19. of the command is given by Delay of Activation Time Delay on Activation Base Time x Delay on Activation Factor e 1 sec Timing Base Time e 1 minute e 1 hour Timing Factor 1 255 The Tus time set for automatic turn off is given by Timing duration Timing Base Time x Timing Factor 33 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 AE sarees QR CCIAA Milano 148549 K x 1088BO1KNXFI01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook Duration of relay activation TLs and ON del Telegram ay time TON are programmable by ETS NO is closed Contact type NO NO is open ON delay time Ton can be disable by ETS Telegram NO is closed Contact type NO NO is open Timing can be stopped Warning Function Warning Time seconds before time ends Switch Off Time Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 True DI his sec DI os sec D 34 64 1088B01KNXF101010002 D0C KNX 1088B01KNXF101010002 DOC O eceleciron Din Rail U
20. on release x Input 1 Short Pess 0 d DN OFF S Every single input channel can be configured to perform one of the following functions Digital input o Short action on press or release or both ON OFF TOGGLE o Short amp long press function ON OFF TOGGLE o Short amp long press function with different communication objects Scene management Dimmer management Brighter Darker Brighter amp Darker Blind Roller Shutter management Up Down Up amp Down Led ON OFF Led Blinking KNX PARAMETER SETTINGS e Digital Input e Dimming e Shutter and Blind Function e Scene e Output Led ON OFF e Output Led Blinking e Digital input see paragraph 5 Digital Input e Dimming see paragraph 6 Dimming e Shutter and Blind see paragraph 7 Shutter and Blind e Scene see paragraph 8 Scene Management e Output Led ON OFF see paragraph 9 Led output e Output Led Blinking see paragraph 9 Led output Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 9 64 1088B01KNXF101010002 DO0C os KNX 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook Contact type e Normally Open e Normally Close This paramete
21. or unlock condition e Relay is Deactivated Relay Position when Lock is Active e Relay is Activated This parameter selects the state the relay must assume when the lock function becomes active See note 2 41 64 Eelectron SpA Via Magenta 77 22 1 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato gg Tribunale di Milano 359157 8760 07 KR CCIAA Milano 148549 K x 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook e Relay is Deactivated e Relay is Activated Position when Lock Ends e Keep previous state and ignore telegrams e Keep previous state and dont ignore telegrams e Relay is Deactivated Relay is in OFF position See note 2 e Relay is Activated Relay is in ON position See note 2 e Keep previous state and ignore telegrams Relay returns in the state it was before lock function became active e Keep previous state and dont ignore telegrams the output channel returns to its condition prior to the activation of the block unless you have received a telegram on the switch object or scenario in this case the last command received is executed NOTES 1 If the parameter Initial Value for Lock Object has the same value of Telegram for Lock Activation
22. parameters when control value telegram is 1 byte W 1 1 1 Din Rail 8 Input 8 Output Module E01 x General Parameter Configuration Channel A Motor Reduction Driver Input Configuration Output Configuration Mete oo O OE X Channel A Motor Reduction Driver Dirver Control Telegram e Output 3 Relay ON OFF GE Output 4 Relay ON OFF Lower Limit Value a Output 5 Relay ON OFF Ge Output 6 Relay ON OFF Upper Limit Value fico DI Output 7 Relay ON OFF i Output 8 Relay ON OFF Total Travel Time sec en ed Pause Between 2 Movement 500 ms DI Anti Locking Function Disabled e Sending state telegram When status change DI Behaviour on power up Keep status before power down DI Lock Function Enabled Disabled DI 61 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DO0C C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato A Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 K N x 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook KNX PARAMETER SETTINGS Driver Control Telegram e 1 bit e 1 byte This parameter defines whether the control of the valve is carried out with 1 bit ON OFF only or 1 byte commands 0 to 100 with intermediate positons Total travel time 0 3000 sec This represent
23. telegram 0 Telegram NO is closed Contact type NO NO is open NO is closed Contact type NC NO is open 31 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato gt i A Tribunale di Milano 359157 8760 07 s CCIAA Milano 148549 K X 1088B01KNXF1I01010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook 12 6 Function ON OFF with delay In this configuration it is possible to set a time delay on the relay activation Ton and also a delay time for the relay deactivation TOFF The opening and closing of the contact when the parameters are different from zero occurs later than the receipt of the telegram activation and deactivation delays are set separately Function ON OFF with dey zl Delay on Activation we sl Delay on Activation Base Time sl Delay on Activation Factor DO D Delay on Deactivation M Delay on Deactivation Factor sl Delay on Deactivation Base Time i ti ea KNX PARAMETER SETTINGS Delay on Activation WE e False Delay on Deactivation Tiue e False e 1 sec Delay on Activation Base Time e 1 minute e 1 hour Delay on Activation Factor 1 255 The delay time between the receipt of a telegram and the execution of the c
24. the time the alarm is still active Wi 1 1 1 Din Rail 8 Input 8 Output Module E01 xj lt Channel gt Alarm General Parameter Configuration Input Configuration Output Configuration BEE a E ai Channel A Shutter and Blinds Supervision Time for Alarm min 30 ES lt Channel A gt Scene Shutter Position when Alarm is Active Move UP P lt Channel A gt Alarm lt Channel A gt Lock Output 3 Relay ON OFF Output 4 Relay ON OFF Output 5 Relay ON OFF Output 6 Relay ON OFF Output 7 Relay ON OFF Output 8 Relay ON OFF KNX PARAMETER SETTINGS Supervision Time for Alarm min 1 120 min This parameter selects how long the supervision time for the alarm function is If this time is set for example to 30 min the shutter need to receive at least one time in 30 min a telegram from the sensor even if the telegrams means no alarm It this not happens the alarm became active lack of supervision and need to receive a no alarm telegram to reset For this only sensor with cyclic sending can be used and we strictly recommend set the supervision at least double the cyclic sending period e Move Up Shutter Position when Alarm is Active e Move Down e Stop no movement This parameter selects the values associated to the alarm condition A If the Alarm Function is enabled it is mandatory to link a sensor with cyclic telegram sending if the communication ob
25. the total travel time necessary to move the motor reductor from totally open to totally close Pause between 2 movements 100 ms 5 sec This represent the minimum time the motor must be in stop between 2 movements 1 bit telegram Activation telegram e Telegram 0 e Telegram 1 It is possible to set a parameter to determine if the Open movement is activated with a telegram 0 and then Close with 1 or vice versa Sending State Telegram e Disabled e When status changes e On request e Disabled not visible e When status changes Status is never transmitted ad related communication object is Status is transmitted every time the relay switch changing his status from ON to OFF or from OFF to ON e On request Status communication object is available and updated when status changes but the telegram is not transmitted Read propriety is enabled Telegram Value for status sending e Telegram 0 is close e Telegram 0 is open This set the value you want transmit when the motor reductor is in open or close position 1 byte telegram Lower limit value j Ge 207 e 10 e 30 Defines the minimum value below which the valve is always closed Baca e 100 e 80 Upper limit value 7 90 70 Defines the maximum value above which the valve is always open Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 931
26. 0159 Capitale sociale 250 000 00 interamente versato gt a A Tribunale di Milano 359157 8760 07 KR CCIAA Milano 148549 K X 1088B01KNXF101010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook When the scene function is enabled a communication object named lt Output x gt Scene becomes visible It is possible to send to the device two possible commands recall scene is a command to create a specific condition store scene is a command to learn and store the current status at the moment the command is received of the contact and then reproduce it once the recall command is received For every channel it is possible to store a maximum of 4 output scene KNX PARAMETER SETTINGS Scene Number lt X gt 0 64 For the 4 possible scenes this number is the unique identifier for the scene valid numbers are from 0 to 63 64 means scene is not active e Contact Open Initial value Scene lt X gt BE For the 4 possible scene this number allow to initialize the status associated to previously selected scene number avoiding to execute the store scene procedure If the store scene is done this value is overwritten e Enabled Learn Scene e Disabled This parameter enable disable the output channel from storing value received from the bus if this parameter is set to disable the value associated are set only by the parameters Initial value Sce
27. 10002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato ua Tribunale di Milano 359157 8760 07 i CCIAA Milano 148549 K X 1088B01KNXF101010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook Output 3 4 Configuration Same values of Output 1 2 Configuration Output 5 6 Configuration Same values of Output 1 2 Configuration Output 7 8 Configuration Same values of Output 1 2 Configuration Output 1 2 Configuration Dutput are independent v Dutput 1 Configuration Generic Load Control v Generic Load Control Dutput 2 Configuration Electric Valve Control Output 1 2 Configuration Dutput are coupled DI Output 1 2 Coupled Driver Motor Reductor v Shutter Driver Motor Reductor KNX PARAMETER SETTINGS e Generic Load Control Output T Configuration e Electric Valve Control Output 1 works in single mode this parameter select which function is set identical parameter for output 2 3 4 5 6 7 8 if configured in single mode e Shutter Suipett EE e Driver Motor Reduction Output 1 and 2 works in coupled mode this parameter selects the function shutter management or motor reduction management Identical parameter for output coupled 2 3 4 5 7 8 Output 2 Configuration Same values of Output 1 Configuration Output 3 Configura
28. 1088BO1KNXFI01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook Din Rail Universal Module 8 inputs 8 outputs lO88E01KNX Product Handbook 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Q Jeelectron MODULE 8IN 80UT 1088E01KNX Ben KNX EIS Ab 220uAC iba CE KNX 23 24 25 2 27 28 17 YA 2 o 2 e 90000 9 p 2 KK E KK SS Product Description Din Rail Universal 8 in 8 out Module Order Code IO88E01KNX Document Version 1 1 Date 22 07 2011 1 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DO0C C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato ree Tribunale di Milano 359157 8760 07 Lafe CCIAA Milano 148549 KNX 1088B01KNXF101010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook INDEX 1 General IntrodUCHiON EE 4 2 Product and functional Overview E 4 2 1 Address and associations IESSE Eh 5 3 General Parameter Configuration ENEE 6 3 1 Parametrs E 6 3 2 Communications Objects Anke 8 4 Input E ee e EE 9 TE UD E 10 5 1 Digital Input Short Action Mode uk 10 5 2 Communications el 11 5 3 Digital Input Long Action Mode uk 11 5 4 Communications ele 12 67 e Kine Le meee ern nme tae ree eo oe De Aer eee ees Tee 13 6 1 Communications EE 14 o Inp t Sh tter and Bie ee
29. 6681 39 02 93507688 info eelectron com www eelectron com C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 62 64 1088B01KNXF101010002 DO0C N KNX 1088B01KNXF101010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook e Disabled Anti Locking Function e Enabled It is possible to enable an automatic valve movement useful when there are long periods of inactivity for example during the summer season If this function is activated you can select how long can be the period of inactivity see parameter Anti Locking Valve movement frequency before that the valve performs a switching ON and after 5 minutes a switching OFF e 1 day Anti Locking Valve movement frequency e 3days e 10 days Determines the maximum period of inactivity allowed e Disabled Lock Function Enabled When lock function is enabled it allows switching the relay in a defined state and forcing it to maintain this state even if the it receives 1 bit or 1 byte control commands e Valve Open Behaviour on power up e Valve Close e STOP no movement On power up it is possible to set the status of each valve with this parameter 15 3 Lock Function When lock function is enabled it allows as a result of receiving a telegram on the lt Output x gt Lock Function to switch the relay in a
30. B01KNXF101010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 13 2 Main Parameters ETS parameters when control value telegram is 1 bit Output 1 Electric Valve Driver Control Value Valve position when relay is open Activation Telegram Sending state telegram Telegram value for status sending Anti Locking Valve Function Lock Function Behaviour on power down Behaviour on power up Ji bit D ETS parameters when control value telegram is 1 byte Output 1 Electric Valve Driver Control Value Valve position when relay is open Cycle Base Time for PWM Lower Limit Value Upper Limit Value Sending state telegram Anti Locking Valve Function Lock Function Behaviour on power down Behaviour on power up Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 h byte De 3 0 v mz 45 64 1088B01KNXF101010002 D0C N KNX 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook KNX PARAMETER SETTINGS e 1 bit Control Value e 1 byte This parameter defines whether the relay controls of the valve is carried out with 1 bit ON OFF or 1 byte 0 to 100 commands When you select the 1 byte v
31. C WA wf K X 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook KNX PARAMETER SETTINGS e 2 pipes system System Type e 4pipes system 2 pipe system the hydraulic system is unique and conveys the warm or cold fluid depending on the season 4 pipe system the hydraulic system has 2 individual circuits one for heating and one for the cooling e Relay is open when valve is deactivated Relay stale Wiel Valve Su paelivateo e Relay is closed when valve is deactivated Set if the relay must switch ON or OFF in order to Open Close the valve the deactivated state for the valve is when it is closed and the fluid does not pass through 11 4 Fan Coil Speed Control The control of 3 speed fan coil can be achieved with 3 communication objects 1 bit which accept commands on off or with a 1 byte communication object for a proportional control KNX PARAMETER SETTINGS Delay between Speed Changes Sec 1 255 This parameter set the pause time between the switching off the relay which control one speed and the switching on of another relay to activate the next speed e 3x 1 bit objects Object type for speed control e 1x1 byte object This set the data type for the speed control e 3x 1 bit objects Object type for speed status e 1x1 byte object This set the data type for the speed feedback to be sent on the
32. F Contact Type Additional Function Activation Telegram Function Relay Feedback Telegram value for status sending Scene Behaviour on power down Behaviour on power up No Function Jonzo FF DI Keep status before power down sl KNX PARAMETER SETTINGS e ON OFF 8 e ON OFF with delay Funguo e ON with delay timing OFF e Continuous Switching e ON OFF After receiving a telegram on the switching objects relay switch e ON OFF with delay e ON with delay timing OFF e Continuous switching in ON or OFF position it is possible to set a delay between the reception of a telegram and the switch of the relay for both telegrams activation and deactivation it is possible to set a delay between the reception of a telegram of activation and the switch of the relay the OFF switch is automatic after a configurable time staircase timer with this function the relay when a 1 bit telegram is received starts switching ON and OFF with a configurable time with the opposite 1 bit telegram it stops and remains in OFF position Activation telegram e Telegram 0 e Telegram 1 For every function above selected you can set a parameter to determine if the function is activated with a telegram 0 and then off with 1 or is activated with telegram 1 and then off with 0 29 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info ee
33. F101010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 8 Input Scene Management Mf 1 1 1 I088E01KNX xi General Parameter Configuration Input 1 Input Configuration Input 2 Function Scene e Input 3 Input 4 Contact Type Normally Open v Input 5 Input 6 Scene Number 0 63 fi Input 7 Input 8 Send Learn Command on Long Action Disabled v Dutput Configuration Output 1 Relay ON OFF Output 2 Relay ON OFF Output 3 Relay ON OFF Output 4 Relay ON OFF Output 5 Relay ON OFF Output 6 Relay ON OFF Output 7 Relay ON OFF Output 8 Relay ON OFF In this configuration page it s possible to set the input channel for scene management learn and recall scene commands These different behaviour recall and learn are performed through two different actions short and long press on a push button connected to the input channel Learn scene on long press action is enabled by a parameter 17 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato gt ge N e Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 K N X 1088BO1KNXFI01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook KNX PARAMETER SETTINGS Contaci type See paragraph 4 Recall
34. Lock Function Enabled Enabled K Shutter Position after Lock and Alarm Previous position and ignore telegrams DI KNX PARAMETER SETTINGS e Shutter Shutter Type e Venetian Select Venetian if the shutter has louvres select shutter if it is a roller shutter Shutter travel time sec 0 3000 This parameter set the total travel time for shutter Extra Time for shutter travel sec 1 255 This parameter indicates the number of seconds to add to the travel time for all the movements that bring the shutter completely up or down Stop time between 2 shutter movements e 100ms e 800 ms e 200 ms e 1 sec e 300 ms e 2sec e 500 ms e 5 sec Eelectron SpA Via Magenta 77 22 1 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 52 64 1088B01KNXF101010002 DO0C eo KNX 1088B01KNXF101010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook Set the minimum time for the shutter to stop from passing from a movement to another Absolute position Ge When enabled this parameter shows 2 communication object SHUTTER POSITION OBJECT and VALUE SHUTTER POSITION OBJECT SHUTTER POSITION a positioning control command can be sent to the device usin
35. PLED e e JE RELAYS e SHUTTER MOVEMENT FEEDBACK OBJECT SHUTTER VALUE SHUTTER POSITION ALARM OBJECT Eelectron SpA Via Magenta 77 22 1 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 POSTION OBJECT 51 64 1088B01KNXF101010002 D0C aS KNX o Aenea 14 2 General Parameters 1088BO1KNXFI01010002 DOC Din Rail Universal 8 Input 8 Output Module Product Handbook W 1 1 1 Din Rail 8 Input 8 Output Module E01 General Parameter Configuration Input Configuration Output Configuration Channel A Shutter and Blinds lt Channel A gt Scene lt Channel A gt Alarm lt Channel A gt Lock Shutter Type Louvres Automatic Movement Step time for louvres movement x 100ms Channel A Shutter and Blinds Venetian Output 3 Relay ON OFF Never zi Output 4 Relay ON OFF E Output 5 Relay ON OFF Shutter Travel Time sec eo kd Output 6 Relay ON OFF a Output 7 Relay ON OFF Extra Time for Shutter Travel sec 2 Output 8 Relay ON OFF Stop Time between 2 Shutter Movements 500 ms D Absolute Position Enabled DI Delay on move up Disabled DI Delay on move down Disabled Scene Enabled be Alarm Function Enabled he
36. Product Handbook 13 3 Lock Function When lock function is enabled it allows as a result of receiving a telegram on the lt Output x gt Lock Function to switch the relay in a defined state and force it to maintain this state even if the object switching value changes The behaviour of the lock function is the same described in par 12 11 Lock Function This function can be enabled or with 1 bit commands than with 1 byte commands W 1 1 1 1088E01KNX x lt Dutput 1 gt Lock General Parameter Configuration Input Configuration Output Configuration d d geg Dutput 1 Electric Valve Driver Initial Yalue for Lock Object Value 0 D Output 2 Relay ON OFF Telegram for Lock Activation Telegram 1 x Output 3 Relay ON OFF Output 4 Relay ON OFF Valve Position when Lock is Active Valve Close x Output 5 Relay ON OFF Output 6 Relay ON OFF Position when Lock Ends Keep previous state and ignore telegrams D Output 7 Relay ON OFF Output 8 Relay ON OFF KNX PARAMETER SETTINGS e Value 0 Initial Value for Lock Object kg e Value 1 This parameter selects the value of the lock object after a power on appropriately changing this value it is possible to start the output channel related to the lock function as locked or unlocked See note 1 e Telegram 0 Telegram for Lock Activation e Telegram 1 This parameter selects the values associated to the lock or
37. Scene Number of the scene 0 63 This parameter sets the value of the scene you intend to learn recall one per channel Remember that output devices i e actuators etc generally can manage several scenes each identified by a value that varies from 0 to 63 therefore is important to set this parameter correctly and matching the number set on the actuators Send learn the scene on long action e Disable e Enable If disable long press action is ignored and no telegram is sent to the bus if enable on long press action a learn scene telegram is sent to the bus Time for long operation g op Same values seen in short long action Determines how long must be a press to be considered long if shorter than the selected value the press action will be considered short 8 2 Communications Objects For every input channel configured as Scene these communication objects are used as shown below daer ges e ee A ee A rA u Ejas lt Input 1 gt Recall Scene Scene 1 Byte C R T G34 lt Input 2 gt Recall Scene Scene 1 Byte CR T G35 lt Input 3 gt Recall Scene Scene 1 Byte CR T Ese lt Input 4 gt Recall Scene Scene 1 Byte CR T E37 lt Input 5 gt Recall Scene Scene 1 Byte CR T Ejas lt Input 6 gt Recall Scene Scene 1 Byte CR T Ho lt Input 7 gt Recall Scene Scene 1 Byte CR T Dan lt Input 8 gt Recall Scene Scene 1 Byte CR T Number Nene ______ objet Funston __ eng
38. T 1 Ez Output 2 gt Relay Command OFF On 1 bit C R W Ejs lt Output 2 gt Relay Status OFF On 1 bit ECR T OUT 2 CDA Output 3 gt Relay Command OfF On 1 bit C R W CDe lt Output 3 gt Relay Status OFF On 1 bit CR T DUT 3 CDe lt Output 4 gt Relay Command OfF On 1 bit C R W CD lt Output 4 gt Relay Status Off On 1 bit CR T J OUT 4 Bs lt Output 5 gt Relay Command OfF On 1 bit C R W Ejo lt Output 5 gt Relay Status Off On 1 bit CR T OUT 5 E 10 Output 6 gt Relay Command OfF On 1 bit C R W Eii lt Output 6 gt Relay Status offjon 1 bit CR T OUT 6 EN 12 Output 7 gt Relay Command OFF On 1 bit C R W E13 lt Output 7 gt Relay Status offiOn 1 bit CR e T OUT 7 EN 14 lt Output 8 gt Relay Command OFF On 1 bit C R W H 15 lt Output 8 gt Relay Status OFF On 1 bit CR T i ours 39 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato gt a A Tribunale di Milano 359157 8760 07 7 CCIAA Milano 148549 K x 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 12 10 Logic Function Enabling logical operation allow to submit the command for the output to a result of a logical operation between the communication object lt Output x gt Relay C
39. UT 3 FAN COIL SPEED 1 Connect to fan coil speed 1 ON OFF contact OUT A FAN COIL SPEED 2 Connect to fan coil speed 2 ON OFF contact OUT5 FAN COIL SPEED 3 Connect to fan coil speed 3 ON OFF contact 1 When fan coil actuator is configured as 2 pipes system OUT2 is not used anyway it is configured to switch in the opposite mode of OUT1 When OUT1 goes ON OUT2 goes OFF and vice versa This behaviour can be used to manage systems where the Heating Cooling hydraulic system is based on a 3 way valve which switches 2 times a year when passing from Summer to Winter season and vice versa 11 3 Control of Heating Cooling Valve General Parameter Configuration Input Configuration Output Configuration Output 6 Relay ON OFF Output 7 Relay ON OFF Output 8 Relay ON OFF Relay State when Valve is Deactivated Fan Coil Actuator System Type 2 Pipe System DI Relay is Open when Valve is Deactivated DI Delay between Speed Changes sec hr ss Object Type for Speed Command 3x1 bitobjets zl Object Type for Speed Status 3x1 bitobiets zl Delay on ventilation start min cs Sending state telegram When status change zl Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 24 64 1088B01KNXF101010002 D0
40. al object for long press e Enable If this parameter is disable the telegrams sent to the bus operating on the input channel with short or long press are transmitted from a single CO named lt Input x gt Digital Input otherwise if this parameter is enable the telegram associated to the Long Press Action is transmitted by another CO named lt lnput x gt Long action In this way it is possible to send two different telegrams on two different group addresses e ON Action on short e OFF e Toggle A Action on long e Nothing This parameter selects which telegram in associated to the short or long press A When the TOGGLE function is used to control a single actuator from different inout channels inout channels on the same device but also on different devices the CO Write W flag must be set otherwise the toggle function will not work properly 5 4 Communications Objects Communication Objects associated to Short Long Action Mode are Number Name Lie Function ee Ce a Daa lt Input 1 gt Digital Input OfF On 1 bit C R T a1 lt Input 1 gt Long Action OfF On 1 bit C R WIT 12 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 SE Leer CCIAA Milano 148549 K X 1088BO1KNXFI01010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook
41. alue the control is done through a PWM See note 1 e Valve Open Valve Position when relay is open e Valve Close This parameter permits to set the behavior of the relay according to the state of the valve If you have a valve that opens when the relay is closed and you want it to be activated by an ON command of a thermostat most common situation you must set this parameter at the value Valve Closed and the parameter see below Activation telegram with value Telegram 0 close the valve e Telegram 0 close the valve EES e Telegram 1 close the valve It is possible to set a parameter to determine if the function is activated with a telegram 0 and then off with 1 or is activated with telegram 1 and then off with 0 Cycle Base Time For PWM 5 min to 60 min in step of 5 min See note 1 1 0 Se 2 10 Lower limit value 3 20 4 30 Defines the minimum value below which the valve is always closed 0 10 20 30 5 100 Upper limit value S SH 8 70 Defines the maximum value above which the valve is always open 70 80 90 100 9 Disabled Sending State Telegram 10 When status changes 11 On request e Disabled Status is never transmitted ad related communication object is not visible e When status changes Status is transmitted every time the relay switch changing his status from ON to OFF or from OFF to ON e O
42. ano 148549 K A 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 14 6 Lock Function When lock function is enabled it allows as a result of receiving a telegram on the lt Channel x gt Lock Function to set the shutter in a defined position and force it to maintain this position even if the channel receives move commands General Parameter Configuration lt Channel A gt Lock Input Configuration Output Configuration a Gas eats Initial Value for Lock Object Value 0 z lt Channel A gt Scene ae Channel A gt Alarm Lock Activation Telegram Telegram 1 Se lt Channel gt Lock open 3 ON OFF Shutter Position when Lock is Active Stop no movement e Output 4 Relay ON OFF Output 5 Relay ON OFF Output 6 Relay ON OFF Output 7 Relay ON OFF Output 8 Relay ON OFF KNX PARAMETER SETTINGS e Value 0 Initial Value for Lock Object KID e Value 1 This parameter selects the value of the lock object after a power on appropriately changing this value it is possible to have the shutter channel related to the lock function as locked or unlocked See note 1 e Telegram 0 Lock Activation Telegram af e Telegram 1 This parameter selects the values associated to the lock or unlock condition e Move Up Shutter Position when Lock is Active e Move Down e Stop no movement Th
43. bjects HEATING COOLING ee gef e e HEATING COOLING s FEEDBACK COOLING O SPEED 1 SPEED 1 FEEDBACK SPEED 2 SPEED 2 OUT3 5 e e FEEDBACK oo e SPEED 3 SPEEDS FEEDBACK SPEED CONTINUOUS CONTROL SPEED CONTINUOS CONTROL FEEDBACK 23 64 Eelectron SpA Via Magenta 77 22 1 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 D0C C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato een Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 K X 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 11 2 Electric connections For 4 pipes systems Uscita Descrizione Collegamento OUT 1 VALVE HEATING Connect to heating valve ON OFF contact OUT2 VALVE COOLING Connect to cooling valve ON OFF contact OUT 3 FAN COIL SPEED 1 Connect to fan coil speed 1 ON OFF contact OUT 4_ FAN COIL SPEED 2 Connect to fan coil speed 2 ON OFF contact OUT 5_ FAN COIL SPEED 3 Connect to fan coil speed 3 ON OFF contact For 2 pipes systems Uscita Descrizione Collegamento OUT 1 VALVE HEAT COOL Connect to heating cooling valve ON OFF contact OUT2 See note 1 O
44. d state and forcing it to maintain this state even if the it receives 1 bit or 1 byte control commands e Valve Open Behaviour on power down e Valve Close e STOP no movement When bus voltage fall down under approximately 18V device enters the power down routine and it is possible to set the status of the relay status See note 2 e Valve Open Behaviour on power up e Valve Close e STOP no movement On power up it is possible to set the status of each valve and therefore the relay with this parameter See note 3 NOTES 1 This type of control is used when you want to eliminate the hysteresis of the temperature typical of ON OFF control The relay drives the valve with ON OFF commands and make a proportional control 0 100 based on the value received on the CONTINUOUS ONTROL OBJECT modulating the amplitudes of the On and OFF pulses PWM This mode is active when 1 byte control was previously selected It is defined a cycle time in which the actuator is activated at a rate of time and then off again until the end of the cycle time itself 47 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato aa Tribunale di Milano 359157 8760 07 R CCIAA Milano 148549 K X 1088B01KNXF1I01010002 DOC O eceleciron Din
45. e for ON OFF mode 1 bit or when the control value is less than the minimum control value Continuous control parameter Lower limit value 1 byte Vice versa it is considered open when the relay that controls it puts it in open state for ON OFF mode 1 bit or when the control value is greater than or equal to the value of the minimum control value When outputs are configured as Electric Driver with 2 point control ON OFF valve is considered closed when the relay that controls it puts it in a close state and open when the relay puts it in the open state 64 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato aa Tribunale di Milano 359157 8760 07 KR CCIAA Milano 148549 K A
46. e for the relay is ON Duration Time Time ON Base Time x Time ON Factor e 1 sec Time OFF Base Time e 1 minute e 1 hour Time OFF Factor 1 255 The duration time of the OFF state for the relay is OFF Duration Time Time OFF Base Time x Time OFF Factor 38 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 int t t S Tribunale di Milano 3591 7 876007 SE CCIAA Milano 148549 K xX 1088BO1KNXFI01010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook Activation Telegram Telegram 1 Contact Type Normally Open Telegram 1 0 NO close Normally Open NO open KNX PARAMETER SETTINGS Start Continuous Switching on Power Up a If set to True this parameter enable the activation of continuous switching on power up without waiting for the activation telegram it starts automatically A If this parameter is set to TRUE the continuous switching starts automatically on Power ON regardless of the setting on the parameter Behaviour on power up 12 9 Communication objects Number Name Object Function Length CIR WIT U Data Type Galo Output 1 gt Relay Command OFF On 1 bit C R W map lt Output 1 gt Relay Status OFF On 1 bit CR T DU
47. e telegram When status change be KNY PARAMETER SETTINGS e 90 Ko e 80 Limit Value Speed 2 3 e 70 e 60 Limit value of control to pass from Speed 2 to Speed 3 e 10 oe e 20 Limit Value Speed 1 2 e 30 e 40 Limit value of control to pass from Speed 1 to Speed 2 e 0 Lower Limit Value e 5 e 10 Limit value of control to pass from Speed 1 to OFF For example if values 70 30 and 0 are selected 100 S3 ON Values of CO 70 Fan Coil Speed Control Yo Dey cane Bee vee Active speed S2 ON 30 S1 ON 0 26 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato gt ge N Tribunale di Milano 359157 8760 07 AD CCIAA Milano 148549 K IN x 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook KNX PARAMETER SETTINGS Sending state telegram e Disable e When status changes e On request The parameter defines the behavior of the object as Disabled Not available When status changes updated on switching and transmitted on the bus On request updated on switching spontaneously and not transmitted on the bus but only on request 12 Output Configuration for Generic Load Control The functional diagram of each
48. electron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 SE eer CCIAA Milano 148549 K X 1088B01KNXF1I01010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook Example of logic function If a relay has AND function enabled and delay on activation deactivation enabled RELAY CONTROL LOGICAL FUNCTION RESULT BEHAVIOUR 0 0 0 1 0 0 Start a delay on deactivation 1 1 1 Start a delay on activation 12 11 Lock Function When lock function is enabled it allows as a result of receiving a telegram on the lt Output x gt Lock Function to switch the relay in a defined state and force it to maintain this state even if the object switching value changes Output 1 Relay ON OFF General Parameter Configuration Input Configuration Output Configuration Output 1 Relay ON OFF Contact Type NO Normally Open DI lt Output 1 gt Lock SE Output 2 Relay ON OFF Additional Function Lock Function Enabled KNX PARAMETER SETTINGS e Value 0 Initial Value for Lock Object as e Value 1 This parameter selects the value of the lock object after a power on appropriately changing this value it is possible to start the output channel related to the lock function as locked or unlocked See note 1 e Telegram 0 Telegram for Lock Activation ugn e Telegram 1 This parameter selects the values associated to the lock
49. es a function for enabling disabling the opening and closing of the valve send information about the position open closed of the valve using a 1 bit telegram send information about the proportion of active regulation using a 1 byte telegram 60 64 Eelectron SpA Via Magenta 77 22 1 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 1088B01KNXF101010002 DOC N KNX 1088B01KNXF101010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 15 2 Main Parameters ETS parameters when control value telegram is 1 bit W 1 1 1 Din Rail 8 Input 8 Output Module E01 x General Parameter Configuration Channel A Motor Reduction Driver Input Configuration Output Configuration AA WA SEEGER aa Driver Control Telegram Output 3 Relay ON OFF DE Output 4 Relay ON OFF Activation Telegram Telegram DI DI Output 5 Relay ON OFF E Output 6 Relay ON OFF Total Travel Time sec Jet I Output 7 Relay ON OFF Output 8 Relay ON OFF Pause Between 2 Movement 500 ms 7 Anti Locking Function Disabled v Sending state telegram when status change Telegram value for status sending Telegram 0 is close DI Behaviour on power up keep status before power down Lock Function Enabled Disabled DI ETS
50. g a percentage value the value is relative to the percentage of closure 10 50 etc 0 shutter totally up shutter totally down VALUE SHUTTER POSITION through 1 byte telegram the information on the current shutter position can be sent the value is relative to the percentage of closing Enabled e E sec Delay on move up Time for Delay on move up Delay on move down S Time for Delay on move down 5 sec z KNX PARAMETER SETTINGS e Disabled Delay on move up e Enabled Enable disable a delay between the receipt of an up command and the start of the movement e 5sec Time for Delay on move up Ge Ge e 30sec Values for the delay e Disabled Delay on move down e Enabled Enable disable a delay between the receipt of a down command and the start of the movement 5 sec 10 sec 20 sec 30 sec Time for Delay on move down Values for the delay 53 64 Eelectron SpA Via Magenta 77 22 1 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 1088B01KNXF101010002 D0C gg KNX 1088BO1KNXFI01010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook These parameters can be used if you want to drive double doors In this case one door must star
51. h the condition of valve powered the other to valve not powered f you use this configuration the control algorithm must be resident in the control device thermostat etc the relay act only to power or not the valve The functional diagram of each output configured as electric valve control is represented in the following scheme LOCK FUNCTION OBJECT 2 POINT CONTROL OBJECT 1 BIT STATUS OBJECT CONTINUOUS CONTROL OBJECT 1 BYTE STATUS OBJECT RELAY wes 2 POINT CONTROL OBJECT CONTINUOUS CONTROL OBJECT LOCK FUNCTION OBJECT 1 BIT STATUS OBJECT 1 BYTE STATUS OBJECT receive 1 bit commands to open and close the valve receives 1 byte commands 0 100 to open and close the valve throught a PWM sequence if enabled according to the receipt of a 1 bit telegram realizes a function for enabling disabling the opening and closing of the valve send information about the position open closed of the valve using a 1 bit telegram send information about the proportion of active regulation using a 1 byte telegram 44 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 1088B01KNXF101010002 D0C aS KNX 1088
52. hter Darker 1 4 Brighter D arker Dimming step 1 8 Brighter D arker 1 16 Brighter Darker 1 32 Brighter Darker 1 64 Brighter Darker 13 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato mg Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 K x 1088BO1KNXFI01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook Max brightness min brightness When a long press is detected device sends on the bus a specific command in order to increase decrease 100 the brightness when the contact returns in its normal condition open or close it depends on the Contact type parameter selects a STOP telegram is sent 1 2 or other values Brighter Darker Behaviour is the same of the previous setting but when a long press is detected device sends a command to the bus in order to increase decrease 1 2 50 the brightness 1 4 means 25 1 8 means 12 5 1 16 means 6 25 1 32 means 3 125 1 64 means 1 56 Minimum Time for long press operation Same values seen in short amp long action Determines how long must be a press action to be considered long if shorter than the selected value the press will be considered short A When the BRIGHTER DARKER function is used to control a
53. il a lock off command is received any command received during the period in which the block is activated is not executed e ALARM FUNCTION this function allows linking the shutter channel to a rain or wind sensor to protect it from damage This function if enabled requires the sensor linked to send cyclically a telegram even if The alarm is off If the shutter does not receive any telegram for a defined time see parameter supervision time for alarm it goes in the alarm position as if it would have been received a alarm telegram 55 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato aa Tribunale di Milano 359157 8760 07 R CCIAA Milano 148549 K X 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook Channel Shutter and Blinds lt Channel A gt Scene lt Channel A gt Alarm lt Channel gt Lock 14 5 Scene Function When the scene function is enabled a communication object named lt Channel x gt Scene becomes visible It is possible to send to the device two possible commands recall scene is a command to create a specific position of the shutter store scene that is a command to learn and store the current position of the shutter in the moment the command
54. is parameter selects the state the relay must assume when the lock function becomes active See note 2 NOTES 1 If the parameter Initial Value for Lock Object has the same value of Telegram for Lock Activation happens that on power up the shutter channel starts in lock mode waiting for a unlock telegram in order to become active Note that even if the shutter channel starts with lock function active it does not go automatically in the position defined by the parameter Shutter Position when Lock is Active avoiding to have automatic and unexpected movements when the power returns after a black out 57 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato aa Tribunale di Milano 359157 8760 07 KR CCIAA Milano 148549 K X 1088B01KNXF1I01010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook 14 7 Alarm Function Alarm function must be activated if the shutter has to be controlled by weather sensors typically rain and wind sensors The sensor must send telegram 0 if no alarm is active ad telegram 1 if the alarm becomes active When shutter has the alarm function active goes in a defined position and cannot be moved except with if the lock function became active for
55. is received and then reproduce it once the recall command is received For every channel it is possible to store a maximum of 4 output scene KNX PARAMETER SETTINGS Scene Number lt X gt 0 64 For the 4 possible scenes this number is the unique identifier for the scene valid numbers are from 0 to 63 64 means scene is not active Initial value Scene lt X gt Values between 0 and 100 in steps of 5 For the 4 possible scene this number allow to initialize the position associated to previously selected scene number avoiding to execute the store scene procedure If the store scene is done this value is overwritten e Enabled Learn Scene e Disabled This parameter enable disable the output channel from storing value received from the bus if this parameter is set to disable the value associated are set only by the parameters Initial value Scene lt X gt and cannot be modified without a ETS download L I 1 After a ETS download the device assumes the value of parameter Initial value Scene lt X gt as a value in memory for the corresponding scene and overwrites previous memorized scene positions 56 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 int t t S Tribunale di Milano 3591 7 876007 SE CCIAA Mil
56. ject is not linked or no telegram is received before the end of supervision time the alarm becomes active and the shutter goes in alarm position 58 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato gt i A Tribunale di Milano 359157 8760 07 KR CCIAA Milano 148549 K X 1088B01KNXF101010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook 14 8 Shutter position after lock and alarm This parameter set the final position of the shutter after the end of a lock or an alarm condition of course if both functions are no active the value of this parameter is not considered KNX PARAMETER SETTINGS e Move Up e Move Down e Previous position and ignore telegrams Shutter position after lock and alarm This parameter selects the values associated to the alarm condition 14 9 Priority table for communication objects Priority Description high Lock Object PRIORITY Alarm Object Low Move Object Absolute Position Object Scene Object 59 64 Eelectron SpA Via Magenta 77 22 1 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato g
57. le or double push button Scene management LED driving as independent channel ON OFF or BLINKING Output main functions Device 8 outputs on board can be configured in different ways Each output can be configured independently for load control R1 to R8 Each output can be configured independently for ON OFF or continuous switching PWM for Electric valves solenoid actuators EV1 to Ev8 Outputs can be configured in pairs for the management of roller shutters and blinds up to 4 channels Channels A to D Outputs can be configured in pairs for management of Motor Reductor or for solenoid valves with 3 point control or for ventilating grilles up to 4 channels Channels A to D s Fan Coil Actuator for 2 4 pipes systems for Heating Cooling with 3 speed motors relays from 1 to 5 Different configurations can exist simultaneously on the same device as long as they do not use the same outputs relays for example you can set the following configuration 4 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato ream Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 K x 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook e Relay1tos gt Fan Coil Actuator e Out6 gt Generic l
58. lectron com www eelectron com C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 1088B01KNXF101010002 D0C aS KNX 1088B01KNXF1I01010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook e Disabled Relay Feedback e When status changes e On request e Disabled Status is never transmitted ad related communication object is not visible e When status changes Status is transmitted every time the relay switch changing his status from ON to OFF or from OFF to ON e On request Status communication object is available and updated when status changes but the telegram is not transmitted Read propriety is enabled Telegram value for status sending e Telegram 0 when value is OFF e Telegram 0 when value is ON This parameter defines which telegram value is associated to the ON or OFF status 12 4 Additional Functions In IO88E01KNX 3 additional function can be enabled LOCK FUNCTION this function according to the command received from the bus blocks the relay in a specific condition when a lock on command arrives this state is kept until a lock off command is received any command received during the period in which the block is activated is not executed LOGIC FUNCTION This function allows you to control the load not only using the relay Switch Command objec
59. n e Move UP Move DOWN Action on shutter e Move UP on short operation Command STEP UP STOP is sent to the bus on long operation telegram MOVE UP is sent to the bus e Move DOWN on short operation Command STEP DOWN STOP is sent to the bus on long operation telegram MOVE DOWN is sent to the bus e Move UP Move DOWN on short or long operation telegrams STEP STOP and telegrams MOVE UP DOWN are sent alternatively A Time for long operation e SE Same values seen in short long action Determines how long must be a press to be considered long if shorter than the selected value the press action will be considered short 15 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 SE rer CCIAA Milano 148549 K X 1088B01KNXF101010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook A When the Move UP MovE DOWN function is used to control a single shutter from different input channels input channels on the same device but also on different devices the CO Write W flag must be set otherwise the function will not work properly Number Name Group Addresses Object Function Length C R WT U Priority 433 lt Input1 gt Shutter Movement Up Down 1 bit c R wW Low 441 lt Input 1 gt Stop Step Stop Step 1 bit CR T Low
60. n request Status communication object is available and updated when status changes but the telegram is not transmitted Read propriety is enabled 46 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 SE eer CCIAA Milano 148549 K A 1088B01KNXF101010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook e Telegram 0 when relay is open Telegram Value for status sending e Telegram 1 when relay is open This set the value you want transmit when relay is open or close and therefore the valve is open or close according to the parameter Valve Position when relay is open e Disabled e Enabled Anti Locking Valve Function It is possible to enable an automatic switching valve function useful when there are long periods of inactivity for example during the summer season If this function is activated you can select how long can be the period of inactivity see parameter Anti Locking Valve Activation Period before that the valve performs a switching ON and after 5 minutes a switching OFF e 1 day Anti Locking Valve Activation Period e 3days e 10 days Determines the maximum period of inactivity allowed p e Disabled Lock Function e Enabled When lock function is enabled it allows switching the relay in a define
61. ne lt X gt and cannot be modified without a ETS download NOTES 1 When a scene is recalled the output channel behaves in the same way as it would have received a telegram 0 or 1 on the lt Output x gt Relay Command communication objects this means that if a output is normally open with the staircase light timer enabled the receipt of a telegram 1 triggers a timed ON with automatic OFF when the timer expires 2 After a ETS download the device assumes the value of parameter Initial value Scene lt X gt as a value in memory for the corresponding scene and overwrites previous memorized scene positions 43 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 D0C C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato AA Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 K x O celeciron oin 1088B01KNXF1I01010002 DOC Rail Universal 8 Input 8 Output Module Product Handbook 13 Output Configuration for Electric Valve Control Each of the 8 outputs can be configured to drive an electric valve solenoid valve typically used in heating and cooling systems for floor panels Use this output configuration when you want to drive an ON OFF type solenoid valve without motor reductor In this type of valve one of two states open or closed is associated wit
62. niversal 8 Input 8 Output Module Product Handbook KNX PARAMETER SETTINGS e True Timing can be stopped e False This allows you to set the behaviour of the device when it receives a OFF command e True On receiving a OFF command the device immediately executes the command and switch off the relay without waiting the end of the timing phase e False On receiving a OFF command the device ignores the command and continues the timing phase the load is deactivated at the end of the set time and it is not possible to deactivate it using a bus command True Warning Function False 15 sec 30 sec 1 minute 2 minutes Warning Time seconds before time ends 0 5 sec 1 0 sec 1 5 sec 2 0 Sec Switch Off Time Here you can set the warning time before the deactivation of the stairway light function upon which the device will consequently signal the imminent termination of the stairway light function by switching off for a brief time the light Duration of relay timing can be stopped with an OFF command Telegram 1 0 NO close Normally Open NO open v n 35 64 Eelectron SpA Via Magenta 77 22 1 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 e e a eer CCIAA Milano 148549 K A 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input
63. nt from totally up e Movement for a Position command if brings the shutter in a position different from totally up This automatic function moves the louvres up after a shutter down movement and down after a shutter up movement KNX PARAMETER SETTINGS e Never e After up movements Louvres automatic movement e Always e After down movements Set when the automatic movement must start Number of automatic steps after move up 1 15 Number of automatic steps after move down 1 15 This parameter set the time of the movement if this parameter is set to 2 and Step time for louvres movement x 100ms is set to 3 then the automatic movement is 300ms x 2 600ms Pause time between 2 step move x100ms 3 10 Set the minimum time delay between 2 step movements 14 4 Additional Functions In 1O88E01KNX for channels configured for shutters 3 additional functions can be enabled e SCENE FUNCTION The scene function manage two possible commands to the device perform scene that is a command to create a specific condition learn scene that is a command to memorize the current status at the moment the command is received of the shutter position and then reproduce it once the perform command is received e LOCK FUNCTION this function according to the command received from the bus blocks the shutter in a specific condition when a lock on command arrives this state is kept unt
64. oad managment e Out7 Out8 gt Shutter management Channel D Scheme of all possible configurations for each output Relay coe Fan Coil Act ere PETE EE Out2 me On OH Cam EV Channel A OMA R4 Fancolispood2 Channel B Eva Channel B a a SE 2 Channel C Ey 2 Channel C SC e Channel D Ey ji Channel D The physical address group address and parameters are assigned and programmed with ETS tool software In order to commission the device a PC with ETS2 version V1 3 or higher is required as well as an interface to the bus RS232 USB etc 2 1 Address and associations limits The maximum number of group addresses allowed for the device is 50 this means that it is possible to associate the communication objects to a maximum of 50 group addresses The maximum number of logical associations allowed for the device is 63 this means that the maximum number of logical connections between communication objects and group addresses is 63 Caution there is a limit to the number of associations that can be created on the same device between transmission communications objects i e inputs and receiving communication objects i e outputs If you want on the same device add a group address already linked to a transmission communication object input to a receiving communication object output which already has a different group address associated please note that you can
65. of 0 25 mA The output channel can drive the led in 2 different way ON OFF or Blinking flashing KNX PARAMETER SETTINGS Function ON OFF Blinking This parameter selects behaviour associated to the led when is active Time for blinking mode 250 ms 500 ms 750 ms 1 sec This parameter is visible when the function mode period of flashing Blinking is selected and sets the on off Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 19 64 1088B01KNXF101010002 D0C mmm KNX 1088B01KNXF101010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 9 1 Communications Objects For every input channel configured as ed output two different communication objects are used as shown below Number Ri wlt u 433 lt Input 1 gt Led On Off Option 1 bt CRW Dau lt Input 2 gt Led On Off OfF On 1 bit CRW Gass input 3 gt Led On Off OfF On 1 bit CRW 36 lt Input 4 gt Led On Off OfF On 1 bit C R W G37 lt Input 5 gt Led On Off OfF On 1 bit CRW Das lt Input 6 gt Led On Off OfF On 1 bit CRW E39 lt Input 7 gt Led On Off OfflOn 1 bit C R W G40 lt Input 8 gt Led On Off OfF On 1 bit CRW Number
66. ommand is given by Delay of Activation Time Delay on Activation Base Time x Delay on Activation Factor e 1 sec Delay on Deactivation Base Time e 1 minute e 1 hour Delay on Deactivation Factor 1 255 The delay time between the receipt of a telegram and the execution of the command is given by Delay of Deactivation Time Delay on Deactivation Base Time x Delay on Deactivation Factor 32 64 Eelectron SpA Via Magenta 77 22 1 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 SE eer CCIAA Milano 148549 K x 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 12 7 Function ON with delay timing OFF After receiving a telegram from the Relay Command Object the relay is active for a time TLs that can be set by a parameter when TLs expires it turns off automatically It is also possible to set a delay on activation time Ton see ON with delay function Delay on Activation z Delay on Activation Base Time 1 sec Delay on Activation Factor 1 Timing Time Base ji sec DI Timing Factor fi KNX PARAMETER SETTINGS Delay on Activation GE e 1 sec Delay on Activation Base Time e 1 minute e 1 hour Delay on Activation Factor 1 255 The delay time between the receipt of a telegram and the execution
67. ontrol and another communication object called lt Output x gt Logic Function By ETS is possible to select the logical operation to use every time a telegram is received on the logical object or on the control object the logical operation is calculated again and the result is taken as a command for the relay lt Output 1 gt Logic General Parameter Configuration Input Configuration Output Configuration Output 1 Relay ON OFF lt Qutput 1 gt Logic M EES Output 2 Relay ON OFF Initial Yalue for Logic Object Output 3 Relay ON OFF Logic Function AND SS KNX PARAMETER SETTINGS e AND Logic function e OR XOR This parameter selects the logical operation e Value 0 Initial Value for logic Operation a Value 1 This parameter selects the value the logical object must have on power up see note 1 If the relay has a timing or a delay on activation or deactivation etc a logical operation result that bring to command 0 or 1 determines a new behaviour of the relay that follows its own parameterization NOTES 1 The value assumed by the logic communication object set by the parameter Initial Value for logic Operation does not switch automatically the relay because this behaviuor is determined by the parameter Behaviour on power up 40 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www e
68. output configured as Generic Load Control is represented in the following scheme SCENE OBJECT LOCK OBJECT LOGIC OBJECT RELAY FEEDBACK a OBJECT SWITCH OBJECT Eelectron SpA Via Magenta 77 22 1 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 27 64 1088B01KNXF101010002 D0C aS KNX 1088B01KNXF1I01010002 DOC Q eelectron Din Rail Universal 8 Input 8 Output Module Product Handbook 12 2 General Parameters KNX PARAMETER SETTINGS e NO Normally Open Contact type e NC Normally Close With this parameter you can set the operating mode of the relay The relay can be used as open contact or close contact This difference is logical because the relay has only one pole and it is not available a terminal connected to the NC contact OUTPUT Relay status NO Normally Open NC Normally Close ON Activated NO contact is closed NO contact is open OFF Deactivated NO contact is open NO contact is closed KNX PARAMETER SETTINGS e ON Behaviour on power down e OFF e STOP no movement When bus voltage fall down under approximately 18V device enters the power down routine and it is possible to set
69. r selects which is the normal condition for the input channel open or close If you select Normally Open the device detects the closing of the input to determine which telegram to send otherwise if you select Normally Close the front detected is the opening one This parameter must be considered also for the short and long press function if you select Normally Open the device detects how long the input is closed to determine if the press is short or long otherwise if Normally Close is selected the device detects how long the input is opened to distinguish between short or long press 5 Digital Input KNX PARAMETER SETTINGS e Only short Action e Short Long Through this parameter it s possible to configure an input channel to send a telegram with different values associated using long or short press or decide to send commands only on one of these two events 5 1 Digital Input Short Action Mode KNX PARAMETER SETTINGS ON OFF TOGGLE Nothing Action on push ON OFF TOGGLE Nothing Action on release This parameter allows to set which behaviour is expected when a edge is detected on a input channel the difference between make or break contact is made with the parameter Contact type e ON on make break contact telegram 1 ON is sent e OFF on make break contact telegram 0 OFF is sent e TOGGLE on make break contact the actual CO value i
70. rts in lock mode waiting for a unlock telegram in order to become active Note that even if the relay starts with lock function already active it does not go automatically in the position defined by the parameter Relay Position when Lock is Active because this behaviuor is determined only by the parameter Behaviour on power up 2 The valve opened and valve closed conditions for each output channels correspond to ON or OFF condition of the upon the settings made for the Valve Position when relay is open parameter 50 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 SE Leer CCIAA Milano 148549 K A 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 14 Output Configuration for shutter and blinds Outputs can be configured in pairs for the management of roller shutters and blinds up to 4 channels Channels A to D Channel Output Function Output Function CHA OUT 1 closed A move up OUT 2 closed YV move down CHB OUT 3 closed A move up OUT 4 closed V move down CHC OUT 5 closed A move up OUT 6 closed Vv move down CH D OUT 7 closed A move up OUT 8 closed XZ move down SCENE OBJECT LOCK OBJECT SHUTTER MOVEMENT SHUTTER STOP LOUVRES COU
71. s Through this parameter is possible to set the delay of transmission of telegrams after a power on by selecting the time by which the device is allowed to send telegrams In large systems after a power failure or shutdown this delay avoids to generate excessive traffic on the bus causing slow performance or a transmission block If there are different devices that require sending telegrams on the bus after a reset these delays must be programmed to prevent traffic congestion during the initialization phase The input detection and the values of objects are updated accordingly at the end of the transmission delay time At the end of ETS programming the device behaves like after a power on 6 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato gt N Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 K xX 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook KNX PARAMETER SETTINGS Debounce time 20 ms 80 ms 150 ms 40 ms 100 ms 200 ms When a button is pressed it is possible to have the contact opened or closed more than once before fixing into a stable position this can be caused by a rapid succession of bounces between mechanicals contacts For this reason it is
72. s evaluated and a telegram with opposite value is sent A e Nothing Edges on input channels are ignored 10 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 SE eer CCIAA Milano 148549 K x 1088B01KNXF101010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook A When the TOGGLE function is used to control a single actuator from different inout channels inout channels on the same device but also on different devices the CO Write W flag must be set otherwise the toggle function will not work properly 5 2 Communications Objects Communication Objects associated to Short Action Mode are Number Name i ject Function tenath cfr wt u m33 lt Input 1 gt Digital Input OfF On 1 bit C R W T Dan lt Input 8 gt Digital Input OfF On 1 bit C R W T E34 lt Input 2 gt Digital Input OFF On 1 bit C R W T Ess lt Input 3 gt Digital Input OFF On 1 bit C R W T CDze lt Input 4 gt Digital Input OfF On 1 bit C R W T Da lt Input 5 gt Digital Input OfF On 1 bit C R W T Hiss lt Input 6 gt Digital Input OFF On 1 bit C R W T ss lt Input 7 gt Digital Input OFF On 1 bit C R W T 5 3 Digital Input Long Action Mode E 1 1 1 I088E01KNX MAA Na xl General Parameter Configuration Input Configuration Input 1 Output Configuration
73. single dimmer from different input channels input channels on the same device but also on different devices the CO Write W flag must be set otherwise the function will not work properly Number Name Group Addresses Object Function Length CRW TU Priority 433 lt Input 1 gt Off On Dimmer Off On 1 bit CR WT Low ES lt Input 1 gt Dimming Brighter Darker 4 bit CR T Low 6 1 Communications Objects For every input channel configured as Dimming two different communication objects are used as shown below Number Name Object Function Length CIR WIT ju CDA lt Input 1 gt Dimming Brighter Darker 4 bit CR T Das lt Input 1 gt OftiOn Dimmer OfF On 1 bit C R W T G42 input 2 gt Dimming Brighter Darker 4 bit CR E G34 lt Input 2 gt Off On Dimmer OfF On 1 bit C R W T G43 lt Input 3 gt Dimming Brighter Darker 4 bit C R T Gass lt Input 3 gt Off On Dimmer OfF On 1 bit C R W T 44 lt Input 4 gt Dimming Brighter Darker 4 bit CR T G36 lt Input 4 gt OFF On Dimmer OfF On 1 bit C R W T Ejas lt Input 5 gt Dimming Brighter Darker 4 bit CR T Dan lt Input 5 gt OFF On Dimmer OFF On 1 bit C R W T 46 lt Input 6 gt Dimming Brighter Darker 4 bit ER T Ejas lt Input 6 gt OfF On Dimmer OFF On 1 bit C R W T 47 lt Input 7 gt Dimming Brighter Darker 4 bit CR T Daa lt Input 7 gt Off On Dimmer off on 1 bit CR WT 4a lt Input 8 gt Dimming Brighter Darker 4 bit CR T Dan
74. t N Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 K x 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 15 Output Configuration for motor reduction driver Outputs can be configured in pairs for the management of motor reductor up to 4 channels Channels A to D Channel Output Function Output Function CHA OUT 1 closed OPEN OUT 2 closed CLOSE CHB OUT 3 closed OPEN OUT 4 closed CLOSE CHC OUT 5 closed OPEN OUT 6 closed CLOSE CH D OUT 7 closed OPEN OUT 8 closed CLOSE This configuration can be used to drive a bistable device with motor reductor typically a solenoid valve with 3 point control or a driver for ventilation grilles in gt AC systems etc Motor MUST have position limit switches Typical wiring scheme Communication object scheme LOCK FUNCTION OBJECT 2 POINT CONTROL OBJECT CONTINUOUS CONTROL OBJECT 2 POINT CONTROL OBJECT CONTINUOUS CONTROL OBJECT LOCK FUNCTION OBJECT 1 BIT STATUS OBJECT 1 BYTE STATUS OBJECT Common Open O Close e Position limit switch 1 BIT STATUS OBJECT COUPLED e e 1 BYTE STATUS OBJECT RELAYS se 1 bit command to open close the valve completely 1 byte command 0 100 to set the valve position if enabled according to the receipt of a 1 bit telegram realiz
75. t but using the result of a logic operation the logic function consists in two logic ports the operation is performed among the logic input and the relay command object SCENE FUNCTION The scene function manage two possible commands to the device perform scene that is a command to create a specific condition learn scene that is a command to memorize the current status of the contact at the moment the command is received and then reproduce it once the perform command is received LOCK and LOGIC function are alternative functions and only one of them can be enabled at a time 30 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 D0C C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato AA Tribunale di Milano 359157 8760 07 s CCIAA Milano 148549 K X 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 12 5 Function ON OFF The relay switches when a message is received on the Relay Command Object Behavior of the relay set to NO and NC when activation telegram is telegram 1 Telegram 0 1 1 0 NO is closed Contact type NO NO is open SE __ 3 L_ NO is closed a Contact type NC NO is open es Behavior of the relay set to NO and NC when activation telegram is
76. t e Same values of command object e Valve Open valve open position e Valve Close valve closed position e Stop no movement motor remains in the state it is when the lock was active e Same values of command object the output channel returns to its condition prior to the activation of the block unless you have received a telegram on the command object in this case the last command received is executed NOTES 1 If the parameter Initial Value for Lock Object has the same value of Telegram for Lock Activation happens that on power up the output channel starts in lock mode waiting for a unlock telegram in order to become active Note that even if the channel starts with lock function already active it does not go automatically in the position defined by the parameter Relay Position when Lock is Active because this behaviuor is determined only by the parameter Behaviour on power up 15 4 Function VALVES ALL CLOSED When at least one output is configured on the device type Electric Valve Driver or Motor Reduction Driver Solenoid Actuator you can enable a communication object that sends 1 bit value telegram 0 when all the valves are turned off and a telegram 1 when at least one valve among those the device is controlling is active For outputs configured as Motor Reduction Driver the valve is considered closed when the relay that controls it puts it in closed stat
77. t first in opening and the other must start first in closing 1st TO OPEN OPENING az IA Be w CLOSING d f bw TO CLOSE Shutter Type Step time for louvres movement x 100ms Louvres Automatic Movement Number of Automatic Step after move up Number of Automatic Step after move down Pause Time between 2 Step Move x 100ms KNX PARAMETER SETTINGS Step time for louvres movement x 100ms 1 180 This parameter selects how long the movement for every step of the louvres is visible only if shutter type is Venetian range from 100 ms to 18 sec 54 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato gt N Tribunale di Milano 359157 8760 07 K x CCIAA Milano 148549 1088B01KNXF1I01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 14 3 Louvres automatic movement If the channel is configured for Venetian control Parameter Shutter Type Venetian it is possible to enable an automatic movement of the louvres which is executed at the end of movements of the shutter these movements are e Movement for scene command if brings the shutter in a position different from totally up e Movement at the end of a lock or alarm state if brings the shutter in a position differe
78. th is w 1 fo Das lt Input 1 gt Recall Store Scene Scene 1 Byte C R T E34 lt Input 2 gt Recall Store Scene Scene 1 Byte CR T Gass lt Input 3 gt Recall Store Scene Scene 1 Byte CR T G36 lt Input 4 gt Recall Store Scene Scene 1 Byte C R T E37 lt Input 5 gt Recall Store Scene Scene 1 Byte CR T Ejas lt Input 6 gt Recall Store Scene Scene 1 Byte CR T E39 lt Input 7 gt Recall Store Scene Scene 1 Byte CR T Dan lt Input 8 gt Recall Store Scene Scene 1 Byte CR T 18 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato gt a A Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 KI X 1088BO1KNXFI01010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 9 Led Output E 1 1 1 IO8S8EO1KNX General Parameter Configuration Input Configuration Input 1 Input 2 Input 3 Input 4 Input 5 Input 6 Function Input 1 Led Output ON OFF Ml 1 1 1 1088E01KNX i x General Parameter Configuration Input Configuration Input 1 Input 2 Input 3 Input 4 Input 5 Input 6 Input 7 Input 8 Function Led Blinking Time Input 1 Led Output Blinking IO88E01KNX device has 8 input channels configurable as output able to drive one led with a maximum current consumption
79. the status of the relay status See note 1 e ON Behaviour on power up e OFF e Keep status on power down On power up it is possible to set the status of each relay with this parameter see note 2 NOTES 1 the device has to accumulate the energy it needs to switch the relays when it is on and stores it into capacitors For this reason when a power down is detected the device has the energy to switch all the 8 relays only if it has been powered from at least 60 seconds and it has not done a full 8 relay switch from at least 20 seconds It is strongly recommended not to select_a full 8 relay switch on power down because the full switch cannot be done in all the situations 2 When is selected the value Keep status on power down for the parameter Behaviour on power up it is maintained the state selected on power down unless you have selected on power down the behaviour STOP no movement in that case it is maintained the state active before power down 28 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato AA Tribunale di Milano 359157 8760 07 e CCIAA Milano 148549 K X 12 3 Relay Functions 1088B01KNXF101010002 DOC Din Rail Universal 8 Input 8 Output Module Product Handbook Output 1 Relay ON OF
80. tion Same values of Output 1 Configuration Output 4 Configuration Same values of Output 1 Configuration Output 5 Configuration Same values of Output 1 Configuration Output 6 Configuration Same values of Output 1 Configuration Output 7 Configuration Same values of Output 1 Configuration Output 8 Configuration Same values of Output 1 Configuration Output 3 4 Coupled Same values of Output 1 2 Coupled Output 5 6 Coupled Same values of Output 1 2 Coupled Output 7 8 Coupled Same values of Output 1 2 Coupled 22 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF101010002 DOC C F e P IVA 11666760159 Capitale sociale 250 000 00 interamente versato ream Tribunale di Milano 359157 8760 07 CCIAA Milano 148549 K x l 1088B01KNXF101010002 DOC O eceleciron Din Rail Universal 8 Input 8 Output Module Product Handbook 11 Output Configuration Fan Coil Actuator This mode should be chosen first in the ETS configuration of the device as if it is enabled commits the outputs from 1 to 5 exclusively Outputs 1 and 2 are interlocked and are dedicated to the operation of switching from cooling mode air conditioning cooling to heating mode and vice versa Outputs from 3 to 5 are interlocked and dedicated to the management of the 3 speed of the Fan Coil Communication o
81. utput 2 Configuration Generic Load Control DI Output 3 4 Configuration Dutput are independent Dutput 3 Configuration Generic Load Control DI Output 4 Configuration Generic Load Control 7 Output 5 6 Configuration Dutput are independent pa Dutput 5 Configuration Genetic Load Control DI Output 6 Configuration Generic Load Control 7 Output 7 8 Configuration Dutput are independent Me Output 7 Configuration Generic Load Control DI Output 8 Configuration Genetic Load Control sl KNX PARAMETER SETTINGS e Disable FAN COIL ACTUATOR Output 1 2 3 4 5 e Enable This parameter defines whether the outputs from 1 to 5 are configured to manage fan coils if the function is enabled outputs 6 7 and 8 remain available as output for generic loads or electric valves control outputs 7 and 8 can be still configured for control of shutters blinds or motor reduction driver e Output are independent Output 1 2 Configuration e Output are coupled Here it is possible to set if outputs are independent and therefore can be set with functions which use only one relay at a time generic loads and electric valve if the option selected is Output are coupled the relays work together to realize functions which use a double relay shutter and motor reduction driver 21 64 Eelectron SpA Via Magenta 77 22 20017 Rho MI Italia 39 02 9316681 39 02 93507688 info eelectron com www eelectron com 1088B01KNXF1010

Din Rail Universal Module 8 inputs / 8 outputs

Contents

Download Pdf Manuals

Related Search

Related Contents