User Manual - Lightspeed Technologies, Inc.
Contents
1. e POWER 2 Ensure sensor cable is attached securely ANCED UDIO TPUTS CHANNEL B SENSOR INPUTS AUDIO OUTPUT 3 Connect DC end of power supply DC POWER to the black power jack labeled SE DC POWER 4 Connect the black AC power cable from the power supply to a wall outlet FINAL CHECK 1 Ensure all cables are appropriately routed out of walking paths and work areas to prevent safety hazards to individuals in the room 2 The amplifier packing material should be kept for warranty shipping purposes 3 Proceed to initial set up to test system performance Leave microphones charging so they are ready for use Microphones will need to be charged on a daily basis 800iX User Manual 14 SEC TO NS Initial Set up Charging and Additional Features 15 800iX User Manual INITIAL SET UP OF REDMIKE LES 800iX Wireless Microphone System 1 Turn the 800iX power switch to the ON position The RED LED on the lt gt x ee switch will glow i o T A VOLUME LightSPEED Slip the REDMIKE with lanyard around the neck and position the top of the microphone just below the collarbone NOTE Positioning of the REDMIKE is critical for proper volume adjustment A VOLUME 4 While speaking in a normal voice a slowly increase the volume of the aod corresponding channel on the 800iX until your voice is barely audible REMEMBER This equipment supplements the user s voice so they are able to speak in2. 1 Ensure that the LT 71 is turned OFF 2 Make sure the cradle charger is plugged into a wall outlet Connect one end of the charging cable into the jack labeled CHARGER on the side of the LT 71 and plug the other end into the charging jack on the rear of the REDMIKE cradle charger The LT 71 s rechargeable batteries are factory installed The LED on the front of the LT 71 will glow RED when charging 3 Leave the LT 71 plugged in overnight 8 10 hrs to obtain a full charge NOTE If the system was purchased without a REDMIKE or REDMIKE VC the LT 71 will utilize the charger jacks on the 800iX Connect the charging cable to one of the jacks labeled CHARGE on the back of the 800iX and connect the opposite end to mte the CHARGER jack on the LT 71 I ae LEVEL i Jg O MIC LINE AUDIO OUTPUT Hlelpiul Hint Microphones can be left in the charger for up to two weeks without degradation to battery life A full charge will be attained in 8 10 hours Fully charged Lightspeed microphones will last over 7 hours 800iX User Manual 25 OPTIONAL HM 70 CONTROLS amp CONNECTIONS ON OFF MUTE Switch This switch 5 Infrared Emitters Avoid covering turns the unit ON OFF or MUTE the emitters as you grip the HM 70 Channel Select Switch CH et cone une Located in the battery compartment transmission from the microphone the switch is set to Channel B at 6 Volume Gain Adjustment the factory Opt
3. Classroom Audio System User Manual CONGRATULATIONS Congratulations on your purchase of the 800iX Infrared Wireless Microphone System This simple yet powerful technology provides the ability to add the benefits of infrared microphone technology to existing amplifiers or to Lightspeed s popular 880iR and 850iR systems to create up to a four channel solution for the classroom The 800iX is a two channel receiver that allows the use of up to two additional microphones simultaneously A standard IR sensor can provide high quality reception in rooms up to 1600 square feet By connecting additional infrared sensors to the receiver the coverage area can be expanded to provide optimal reception in varying room sizes and configurations The REDMIKE is a two channel rechargeable classroom microphone that is clipped to a lavaliere cord and worn around the neck for teacher use or it can be used as a standard handheld microphone for students to pass around when speaking 800iX User Manual i JOUN Usar Manual SAFETY INSTRUCTIONS AND CERTIFICATIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s
4. charge the optional LightMic or handheld mic as an alternative to amplifier using a standard XLR connecting them to the REDMIKE microphone cable cradle charger 6 SENSOR INPUT The IR sensor cable AUDIO OUTPUT This 1 4 unbalanced connects to the sensor input audio output jack may be connected Connect additional sensors to the to a line in jack on a mixer amplifier 8001 to cover large or odd shaped This output is a mixed audio of classrooms channels A and B 7 SENSOR SHORT This LED glows LEVEL MIC LINE Changes the audio when there is a short in one of the level output from the audio sensor cables output jack to mic or line level 800iX User Manual 4 REDMIKE CONTROLS AND CONNECTIONS 90Joq qey K1ojjeq 9sn Udo x REDMI TECHNO POWER BUTTON Press this button to AUDIO MICROPHONE INPUT Use this input turn the REDMIKE ON press again to to plug in a laptop MP3 player or other audio turn it OFF mute source to wirelessly transmit audio to be POWER LOW BATTERY INDICATOR A played through the system Alternatively an BLUE light indicates the REDMIKE is on external microphone can be connected and fully charged A RED light indicates 6 CHANNEL SELECT SWITCH This a charge is needed switch allows for selection between Channel BATTERY COMPARTMENT To access A or B If you are using a single microphone the battery compartment
5. enclosure that may be sufficient magnitude to constitute a risk of electric shock The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance CERTIFICATIONS Complies with 72 23 EEC Low Voltage Directive and 89 336 EEC Electromagnetic Compatibility Directive Compliance was demonstrated to the following specifications as listed in the Official Journal of the European Union EN 60950 Electrical Safety A1 1993 A2 1993 A3 1993 A4 1997 EN 55022 RF Emissions Information Technology Equipment EN 55024 EMC Immunity Standard EN 61000 3 2 Harmonics EN 61000 3 3 Voltage Fluctuation Lightspeed Technologies launched a formal product recycle program in Europe that complies with the European Union Directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE Directive Please visit our website at www Lightspeed tek com for more information This product is manufactured using lead free processes and is free of other materials harmful to the environment It conforms to the most stringent new European guidelines for consumer products RoHS ii 800iX User Manual Read Instructions All safety and operation instructions should be read before this Lightspeed product is operated Retain Instructions The safety and operating instructions should be kept fo
6. follow this procedure Adjust the volume at the computer television or other audio source if possible 2 If the audio source does not have a volume control such as many DVD players adjust the volume at the iRMC 3 If the first two options do not give optimum volume level the last place to adjust the volume is the CH B Volume on the 800iX Felpa mine If you adjust the CH B volume on the classroom audio system you will also be changing the volume for your second microphone Return the CH B volume knob to the original position before turning the second microphone back on 30 800iX User Manual SECTION 4 Troubleshooting Daily Use and Warranty 31 800iX User Manual PROVELES IOC ING e UNDAE Note Most problems are directly related to low battery power Please run through the Battery Check items first For remaining troubleshooting use known good fully charged batteries Battery Check Low Volume or Feedback e Confirm batteries are charged Ensure microphone is positioned each night appropriately just below the collar Confirm proper batteries are used DONE The REDMIKE requires the Lightspeed e Check volume level on the amplifier If BA NH2A27 rechargeable sensing the volume is too high feedback will battery for proper charging The LT 71 occur Adjust accordingly amp HM 70 require NiMH AA rechargeable e Adjust the volume level on the back of batteries the option
7. or in places where the line of sight is or could be obstructed Best placement Good placement 800iX User Manual 10 IR SENSOR INSTALLATION cont d Suspended Ceiling Mount 1 Lift the ceiling tile nearest the grid rail in your desired sensor location Guide one side of the C clip over one edge of the grid rail Providing firm support to the back of the grid rail with one hand to prevent bending firmly and carefully snap the second side of the C clip over the edge of the rail Uncoil sensor wire Connect one end of the sensor cable to the plug on the sensor Secure wire overhead and route it back to the system Connect the other end of the sensor cable into one of the sensor inputs on the back of the system Use conduit to protect wires e Conduit is the best means to keep the wires cables out of sight and safe from wear Conduit is not included 11 800iX User Manual Wall Solid Ceiling Mount Il Fa sensor plug Screw the plastic mounting strip to a place high on the wall or in the middle of the solid ceiling Mount the strip horizontally as shown above Firmly snap the C clip on the back of the IR sensor onto the plastic mounting strip with the sensor plug hanging down if a wall mount or toward the receiver location if ceiling mount Uncoil the sensor wire Screw one end of the sensor cable to the plug on the sensor Route th
8. 800iX Wireless Microphone System A VOLUME B VOLUME BH 56 55 O 800iX Infrared Receiver Amplifier and Power Supply REDMIKE SR 70F Infrared Sensor and cable Classroom Microphone Charging Cradle and Power Supply 800iX User Manual 8 SEASONS ea al O EINER Before running wires to the 800iX A good location would be on any or plugging in find a suitable stable bookcase or shelf within Stable location for the amplifier 6 feet of an electrical outlet The Ideally the teacher should have optional Lightspeed wall shelf part ready access and an electrical Best AC 800WB is specifically designed outlet should be within to support the 800 six feet The best possible location for the 800iX is in a media cabinet with any existing audio video equipment Wires should be routed back directly to the amplifier so select a location that is free from obstructions that may make routing wire difficult Example placing the 800iX near a whiteboard or bulletin board would require the wiring to be run an extra distance in order to reach the amplifier 9 800iX User Manual 3 IR SENSOR INSTALLATION Sensor location is very important for optimum performance of the 800iX Classroom Audio System e BEST On the ceiling at or near the middle of the classroom e GOOD High and centered on the long wall e AVOID Locations in corners on walls at heights lower than 7 feet
9. a conversational tone Having the volume set too high will result in feedback and listener fatigue If a second REDMIKE was purchased repeat NOTE Each REDMIKE steps 2 4 has its channel pre set to either A or B a nd ested on the back of the Mic B VOLUME 800iX User Manual 16 1 Plug power cord into the cradle charger and then plug the AC end into an electrical outlet Ensure that the REDMIKE Place the REDMIKE into the cradle The LED on is turned OFF the cradle will glow RED indicating charging has started When the REDMIKE is fully charged the LED on the cradle charger will change to GREEN REDMIK LIGHTSPEED TECHNOLOGIE Helft mini A e REDMIKE incorporates alkaline protection into the microphone design Replacement AA NiMH batteries may only be purchased through Lightspeed Technologies part BA NH2A27 A blinking LED indicates a charging error Be sure to use a Lightspeed rechargeable sensing battery 17 800iX User Manual 83800iX User Manual USING THE REDMIKE TO AMPLIFY EXTERNAL AUDIO EQUIPMENT The REDMIKE includes a 3 5mm audio input jack to connect to an audio source like a laptop or MP3 player The REDMIKE will transmit the audio signal to be played through the system 1 3 If your system includes two REDMIKEs use the student microphone already set to Channel B NOTE This feature works on both channels but we recommend using Channel B so the t
10. al REDMIKE VC Make sure the microphones are turned off while charging so a full charge is attained Full charge will last eight e Turn the 820iR on Confirm that the hours POWER light located on the front panel switch is on No Sound From Speaker Inspect the battery contacts Clean and adjust if necessary e Confirm signal is being received at the 820iR The IR signal light will be RED indicating a signal is being received e Confirm that REDMIKE is turned on There will be a BLUE LED on the microphone to indicate it is powered on Hearing Static e Ensure sensor is in optimum location refer to sensor placement in manual A single sensor will cover a 1600 sq ft enclosed classroom e Ensure that no other REDMIKE LT71 HM70 is operating on the same channel If the optional iR media connection is in use set the microphone to Channel A If you review these instructions and still have questions write down the serial number and model number of your system and call Lightspeed Technical Services at 800 732 8999 5 a m 5 p m PST 800iX User Manual 32 DAILY USE INSTRUCTIONS 1 TURN ON THE 800iX LES 800iX Wireless Microphone System A VOLUME Ensure the power is switched on 2 POSITION THE REDMIKE Ke Remove the REDMIKE from the charging cradle and place it around your neck Adjust the neck strap so the top of the microphone rests just below your collarbone 4 CHARGE BATTERIES Turn the P
11. arranty service including return shipping labels please contact Lightspeed s Service Department at 800 732 8999 service lightspeed tek com Warranty on infrared microphones is FIVE 5 YEARS Warranty on Lightspeed rechargeable batteries all external cables and wires provided by Lightspeed is one 1 year Prepaid shipping labels are provided by Lightspeed factory or an authorized warranty service center for warranty repairs Warranty does not extend to finish appearance items or malfunctions due to abuse or operation other than specified conditions nor does it extend to incidental or consequential damages Repair by other than Lightspeed or its authorized service agencies will void this guarantee Information on authorized service agencies is available from Lightspeed Technologies Inc Our Service Department 800 732 8999 5 a m 5 p m PST will handle all your repair replacement needs 800iX User Manual 34 SYSTEM SPECIFICATIONS OVERALL SPECIFICATIONS Standard Carrier Frequencies IR Alternative Carrier Frequencies IR Frequency Stability nennen Signal to Noise Ratio Dynamic Range Frequency Response RECEIVER SPECIFICATIONS Receiver Type Receiver Sensitivity Image and Spurious Rejection Dimensions W x D x H TRANSMITTER SPECIFICATIONS REDMIKE and REDMIKE VC Audio Distortion Built in Microphone Battery Power 1 year warranty Audio Input Dimensions W x D x H LT 71 LightMic Au
12. ble REMEMBER This equipment supplements the user s voice so POWER they are able to speak in a conversational tone Having the volume set too high will result in feedback and listener fatigue NOTE A nominal volume level must be set on the 800iX before adjusting controls on the REDMIKE VC 5 The teacher can now use the controls on the REDMIKE VC to adjust the volume level from 3 anywhere in the room The microphone volume control has 4 steps up and 4 steps down from the mid point 9 levels total Help minu NOTE Each REDMIKE VC has its channel pre set to either A or B as indicated on the back of the Mic 21 800iX User Manual Plug power into the cradle charger and then plug the AC end into an electrical outlet 2 Ensure that the REDMIKE VC 3 Place the REDMIKE VC into the cradle The LED on the cradle is turned OFF will glow REDindicating charging has started When the REDMIKE VC is fully charged the LED on the cradle charger will change to GREEN mine e REDMIKE VC incorporates alkaline protection into the microphone design Replacement AA NiMH batteries may only be purchased through Lightspeed Technologies part BA NH2A27 A blinking LED indicates a charging or sensing error see page 7 Be sure to use a Lightspeed rechargeable sensing battery 22 800iX User Manual LT 71 ce ON OFF MUTE Switch This switch 5 Auxiliary AUX Plug a la
13. dio Distortion Built in Microphone Battery Power 1 year warranty Audio Inputs HM 70 Handheld Microphone Audio Distortion Built in Microphone Battery Power 1 year warranty Dimensions W x D x H Mounting Dimensions Weight 35 800iX User Manual JOOX Usar Manual 2 06 2 54 MHz 3 2 3 7 MHZ 3 gt 73 dB gt 73 dB 100 Hz 10 KHz Superheterodyne 6 uV for 60 dB S N gt 70 dB 17 3 x 8 5 x 1 75 5 2 Ibs lt 1 Unidirectional Electret 1 AA NiMH Rechargeable Sensing Battery 3 5 0 9 x 1 0 x 3 5 2 1 oz lt 1 Unidirectional Electret 2 AA NiMH Rechargeable Mic Level 3 5 mm Line Level 3 5 mm 1 375 x 75 x 4 625 Unidirectional Electret 2 AA NiMH Rechargeable 2 25 x 2 25 x 8 75 Up to 1600 square feet per sensor 50 ft Plenum rated Ceiling clip Wall bracket 4 25 Diam x 2 0 H BEN 3000 Usar Ms mus Bs PO OMPFONENTS C ESSORIES Part Number Description RX 800 Infrared receiver amplifier mixer PS 16V 1 0 Power supply battery charger for 800iX Infrared sensor with cable and wall or ceiling mounting Plenum sensor cable 50 ft REDMIKE classroom microphone RMT w lavaliere cord and rechargeable AA battery Lightspeed AA rechargeable sensing battery BA NH2A27 for REDMIKE AC LTCB Lavaliere cord for REDMIKE LT 71 REDMIKE cradle charger PS 5V 1 0 Cradle charger power supply Optional Accessories LT71 LightMic micro
14. disposable protective tab before use 20 800iX User Manual 210354 qey 100P K ayeq apis AUDIO MICROPHONE INPUT Use this input to plug in a laptop MP3 player or other audio source to wirelessly transmit audio to be played through the system Alternatively an external microphone can be connected CHANNEL SELECT SWITCH CH A B This switch allows for selection between Channel A or B If you are using a single microphone we recommend using Channel A VOLUME CONTROLS UP DOWN Adjusts microphone volume by pressing the up or down arrow buttons on the back of the REDMIKE VC CHARGER CONTACTS These contacts interface with the charging tabs in the BC RMCC cradle charger for daily charging Simply place the REDMIKE VC in the charger INITIAL SET UP OF OPTIONAL REDMIKE VC LES 800iX Wireless Microphone System 1 Turn the 800iX power switch to the ON In A VOLUME position The RED LED on the switch ha wi OW LightSPEED 7 2 Turn on the REDMIKE VC The RED IR LED on the 800iX will light to indicate a signal is being received 3 Slip the REDMIKE VC with lanyard around the neck and position the top of the microphone just below the collarbone NOTE Positioning of the REDMIKE VC is critical for proper volume adjustment 4 While speaking in a normal voice slowly increase the volume of the corresponding en A VOLUME channel on the 800iX until your voice mt Ai is barely audi
15. e wire back to the system securing it along the way Connect the other end of the sensor cable to one of the sensor inputs on the back of the system EH EH EN UN NND E UD D D D S S e 1 4 4 CONNECTION TO THE AMPLIFIER 1 Ensure the power switch is in the OFF position and all front panel volume controls are turned fully counter clockwise LES 800iX Wireless Microphone System A VOLUME B VOLUME Al 6 i 2 2 Locate the 1 4 1 4 mono cable 3 Connect the cable from the 1 4 audio output jack on the 800iX to the input jack on the 880iR 850iR or an existing amplifier AUDIO INPUTS VOL VOL COMPUTER ADJ ALD OUT AUX OUT 9 ADJ 850iR Receiver 9 g DC POWER CHARGERS Amplifier ix mi OFF 2avpc AS 880iR Receiver _ 99 m Amplifier Existing 6 OO OO Amplifier KPD MA a ib ASA cC AUDIO OUTPUT DC POWER BALANCED 16V 1A AUDIO O 9 CHARGE LEVEL OUTPUTS 7 SHORT OOO ew 9 9 2 06 2 54 CHANNEL A CHANNEL B SENSOR INPUTS 800iX Receiver 12 800iX User Manual Video In Teacher s Microphone VGA Out Speaker s Video Out Video Out Existing Amplifier 800iX User Manual 13 6 FINALIZING CONNECTIONS 1 Ensure the power switch is in the OFF position and all front panel volume controls are turned fully counter clockwise LES 800iX Wireless Microphone System e of
16. eacher s volume on the CH A does not have to be adjusted REMEMBER It s easy to determine which REDMIKE is set to Channel B by speaking into the mic and watching which set of LED s glow on the front panel of the 8001 B VOLUME Plug your laptop MP3 player or other audio source into the input on the REDMIKE labeled INPUT using a 3 5mm patch cable AUDIO Adjust the volume e LES 800iX Wireless Microphone System of the selected mic lt channel to achieve A VOLUME IR1 AF1 desired loudness meiul hinu The optional LT 71 can also amplify external audio Simply plug the 3 5mm patch cable from the audio source into the input labeled AUX IN and adjust the volume of the source to the desired sound level 800iX User Manual 18 SECTION 4 Optional Microphones and Accessories 19 800iX User Manual 3001 Usar Manus OPTIONAL REDMIKE VC Volume Control CONTROLS amp CONNECTIONS POWER BUTTON Press this button to turn the REDMIKE VC ON press again to turn it OFF mute POWER LOW BATTERY INDICATOR A BLUE light indicates the REDMIKE VC is on and fully charged A RED light indicates a charge is needed BATTERY COMPARTMENT To access the battery compartment slide the door downward The battery should only be replaced by a Lightspeed AA rechargeable sensing battery part BA NH2A27 YELLOW PROTECTIVE TAB Slide the battery compartment door open to remove this
17. full charge The GREEN light will turn off when fully charged NOTE If the system was purchased without a REDMIKE or REDMIKE VC the HM 70 will utilize the charger jacks on the back of the 800iX AUDIO OUTPUT DC POWER BALANCED 16V 1A AUDIO D CHARGE LEVEL OUTPUTS SH r3 A LINE CHANNEL A CHANNEL B SENSOR INPUTS Help minu Do not attempt to charge alkaline batteries They can overheat and expand creating a significant hazard and damaging the LT 71 and HM 70 This is not covered by the warranty 28 800iX User Manual Video In IR Sensor IR Transmission 2 4 Teacher s Microphone VGA Out gt Audio Out Speaker s Audio In Video Out Audio Out Se EET Video Out Audio Out The iRMC is designed to integrate with the 800iX and multiple audio sources allowing other instructional technologies to be clearly heard throughout the classroom 29 800iX User Manual INITIAL SET UP OPTIONAL IR MEDIA CONNECTOR 1 TURN OFF SECOND MICROPHONE The iR Media Connector uses the same channel channel B as the optional second microphone REDMIKE LT71 or HM70 As a result they cannot be used simultaneously If you have a second microphone turn it off before transmitting audio from the iRMC 2 VOLUME ADJUSTMENT The iR Media Connector volume is preset for most standard audio signals If you need to turn the 4 OFF ON ACH B volume up or down
18. imum volume level is Power Charge Indicator The pre set at the factory and no light glows RED when the HM 70 adjustment should be necessary is powered ON GREEN when charging Charger Input CHARGER Plug the charging cable from the charger into this jack for daily charging 800iX User Manual 26 INITIAL SET UP OF OPTIONAL HM 70 re 1 Ensure the 800iX is ON The RED LED on the power switch will glow y N 2 Turn on the HM 70 by sliding the switch to the top position 3 Grip the barrel in the center section Avoid covering the infrared emitters circling the base This could interrupt signal transmission 4 While speaking in a normal voice increase the B VOLUME level until your voice is barely audible REMEMBER This equipment is designed to supplement and distribute the user s voice so they are able to speak in a conversational tone Having the volume set too high will result in feedback and listener fatigue 800iX User Manual 27 1 Ensure that the HM 70 is turned OFF 2 Make sure the cradle charger is plugged into a wall outlet Connect one end of the charging cable into the jack labeled CHARGER on the side of the HM 70 and plug the other end into the charging jack on the rear of the cradle charger The HM 705 rechargeable batteries are factory installed The LED on the front of the Handheld Mic will glow GREEN when charging Leave the HM 70 plugged in overnight 8 10 hrs to obtain a
19. lace the REDMIKE back into the microphone ON using the ON OFF switch on the side of the REDMIKE and speak normally charging cradle to recharge at the end of the day e gt EA Er REDMIK LIGHTSPEED TECHNOLOGIE 33 800iX User Manual Speak in a natural voice Anormal conversational speech levelwill provide an adequate signal It is not necessary to increase the intensity of your voice the audio system provides adequate amplification approximately 5 10 dB above ambient room noises Avoid wearing jewelry that may rub or bump against the microphone Turn the REDMIKE off during private conversations with a student parent or other classroom visitor You can also cover the LED lens on top of the REDMIKE to block the signal Recharge batteries each night When recharged nightly operating time actual usage for the transmitters will last through a typical school day vy Hte Warren Lightspeed Infrared Audio Systems and optional accessories are warranted against malfunction due to defect in materials and workmanship for a period of five 5 years from date of purchase System components will be repaired or replaced at Lightspeed s option Rechargeable batteries and connecting cables are guaranteed for one 1 year Warranty does not extend to finish appearance or malfunctions due to abuse or misuse Repairs performed by other than Lightspeed Technologies will void this warranty For w
20. ng Your System Location of the Receiver Amplifier IR Sensor Installation Suspended Ceiling Mount Wall Solid Ceiling Mount Audio Integration Finalizing Connections Final Check SECTION 3 Initial Set up Charging and Additional Features Initial Set Up of REDMIKE Charging the REDMIKE Using the REDMIKE to Amplify External Audio Equipment SECTION 4 Optional Microphones and Accessories Optional REDMIKE VC Controls and Connections Initial Set Up of Optional REDMIKE VC Charging the Optional REDMIKE VC Optional LT 71 Controls and Connections Initial Set Up of Optional LT 71 Charging the Optional LT 71 Optional HM 70 Controls and Connections Initial Set Up of Optional HM 70 Charging the Optional HM 70 Audio Integration for the Optional iR Media Connector Intial Set Up of Optional iR Media Connector SECTION 5 Troubleshooting Daily Use and Warranty Troubleshooting Guide Daily Use Instructions Tips on Classroom Audio Warranty Statement System Specifications Individual Components and Optional Accessories User Notes 800iX User Manual iii SEC HONDI System Overview 1 800iX User Manual 5 001 User Manual LES 800iX Wireless Microphone System A VOLUME e e SR 70F Infrared Sensor Charging Cradle and Power Supply REDMIKE amp Classroom Microphone Optional LT 71 LightMic and Charger Cable Optional HM 70 Handheld Microphone and Charger Cable Optional REDMIKE VC Volume Control Mic
21. phone with lavaliere cord rechargeable batteries and charging cable Handheld microphone with rechargeable batteries and charging cable HM70 MC TK250LTM Noise canceling headset microphone AC TCC7 Charging cable for LT 71 and HM 70 microphones AC 800WB Audio patch cable 2 5 mm mono to 3 5 mm mono Contact Lightspeed at 800 732 8999 for speaker 800iX User Manual 36 Uses INO Wes Record your system serial numbers and purchase information This is helpful when ordering additional components accessories and or warranty service Components Serial Number 800iX Microphones Sensors Speakers Purchase Information Your School Organization District Purchase Date Invoice 37 800iX User Manual USER NOTES 800iX User Manual 38 USER NOTES 800iX User Manual 39 USER NOTES 800iX User Manual 40 USER NOTES 800iX User Manual 41 gt lightspeeo AC MN800 LIGHTSPEED TECHNOLOGIES 11509 SW HERMAN ROAD TUALATIN OR 97062 TOLL FREE 800 732 8999 PHONE 503 684 5538 FAX 503 684 3197 LIGHTSPEED TEK COM MNO191US01 1
22. ptop MP3 turns LT 71 ON or OFF mute player or other audio source into Channel Select Switch CH this jack to wirelessly transmit the This switch allows for selection signal to be played through of Channel A or B If you are LOSC using a single microphone we Charger Input CHARGER Plug recommend using Channel A the charging cable from the Power Charge Indicator The into this jack daily light glows BLUE when the LT 71 Wie EP one tront m is powered ON RED when being glow RED to indicate charging charged External Microphone Input MIC Use the 3 5mm MIC jack for the optional TK 250 headset microphone part MC TK250LTM 23 800iX User Manual INITIAL SET UP OF OPTIONAL LT 71 1 Turn the 800iX power switch to the SEEN ON position The RED LED on the co switch will glow d 2 Turn on the LT 71 and set the operating channel to 3 Slip the LT 71 with lanyard around the neck and position the top of the micro phone just below the collarbone NOTE Positioning of the LT 71 is critical for proper volume adjustment 4 While speaking in a normal voice increase the B VOLUME level until your voice is barely audible REMEMBER This equipment is designed to Supplement and distribute the user s voice so they are able to speak ina conversational tone Having the volume set too high will result in feedback and listener fatigue 24 800iX User Manual
23. r future reference Heed Warnings All warnings on this Lightspeed product and in these instructions should be followed Follow Instructions All operating and other instructions should be followed Water and Moisture This Lightspeed product should not be used near water Heat This Lightspeed product should be situated away from heat sources such as radiators etc Power Sources This Lightspeed product should be connected to a power supply only of the type described in the operation instructions or as marked on this Lightspeed product Power Cord Protection Power supply cords should be routed so that they are not likely to be walked upon or pinched by items placed upon or against them Object and Liquid Entry Care should be taken so that objects do not fall onto and liquids are not spilled into the Lightspeed product 10 Damage Requiring Service This Lightspeed product should be serviced only by qualified service personnel The user should not attempt to service this Lightspeed product 11 Prevent Electric Shock Do not use this polarized plug with an extension cord receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure Safety Instructions and Certifications SECTION 1 System Overview System Components Front Panel Controls Rear Panel Controls REDMIKE Controls and Connections Cradle Charger Controls and Connections SECTION 2 Installation Unpacki
24. rophone Q nlalprul Himnu Keep ALL packaging materials If the system must be returned using the original packing material will be quick convenient and prevent damage 800iX User Manual 2 POWER POWER Switch POWER Indicator This switch is used to turn the 8001 ON switch up or OFF switch down When the POWER switch is in the ON position the POWER light will glow red IR Indicators IR These lights will glow red when the corresponding microphone is turned on This light confirms the 800iX is receiving a steady infrared signal 3 800iX User Manual OO E FRONT PANEL CONTROLS B VOLUME IR1 e AF Indicators AF These lights flash green when audio voice from the microphone is detected VOLUME Controls the volume level of the teacher microphone that is switched to Channel A Rotating the knob clockwise increases output level VOLUME Controls the volume level of the optional second microphone that is switched to Channel B Rotating the knob clockwise increases output level DC POWER me p NS NS C2 Bid LEVEL OQ e N y WP M 4 CHANNEL CHANNEL e INPUTS 2 06 2 54 DC POWER Plug the 16V power 5 BALANCED AUDIO OUTPUTS Two supply into this jack independent audio outputs that may be connected to a balanced CHARGERS These jacks can be used microphone input jack on the mixer to
25. slide the we recommend using Channel A door downward The battery should CHARGER CONTACTS These contacts only be replaced by a Lightspeed interface with the charging tabs in the BC AA rechargeable sensing battery RMCC cradle charger for daily charging part BA NH2A27 Simply place the REDMIKE in the charger YELLOW PROTECTIVE TAB Slide the battery compartment door open to remove this disposable protective tab before use NOTE do not attempt to remove the tab without first opening the compartment door as it may tear leaving fragments 5 800iX User Manual CRADLE CHARGER CONTROLS AND CONNECTIONS 1 CHARGE INDICATORS The light glows DC POWER PORT Connect the DC power RED while the REDMIKE is charging cord here When fully charged the light will glow GREEN A blinking RED light indicates that no battery is sensed REDMIKE Yellow Protective Tab may not have been completely removed see page 5 item 4 A blinking Green LED means a non Lightspeed battery has been installed possibly an alkaline battery OPTIONAL CHARGING PORT Plug the charging cord for the optional LT 71 or the HM 70 microphones here International Note Appropriate power cord and adaptor are provided with all Lightspeed equipment Mims 9 pu 800iX User Manual 6 SECTION Installation 7 800iX User Manual 1 UNPACKING YOUR SYSTEM Ensure that you have received all of the components of your system LES
Download Pdf Manuals
Related Search