IntelliTone™ Pro
Contents
1. 6799 5566 e Taiwan 886 2 227 83199 e USA 1 800 283 5853 Visit our website for a complete list of phone numbers Unpacking The IntelliTone products come with the accessories listed below If an accessory is damaged or missing contact the place of purchase immediately IT200 IntelliTone Pro LAN Kit IT200 Toner with 9 V battery IP200 Probe with 9 V battery 2 RJ11 to RJ11 patch cords 2 RJ45 to RJ45 patch cords Test lead set banana jacks to alligator clips F connector adapter female to female Quick Reference Guide IT200 IntelliTone Pro LAN Toner IT200 Toner with 9 V battery 1 RJ11 to RJ11 patch cord 1 RJ45 to RJ45 patch cord Test lead set banana jacks to alligator clips F connector adapter female to female Quick Reference Guide A Safety Information IP200 Intellifone Pro Probe Z Warning A e P200 Probe with 9 V battery To prevent possible fire electric shock or e Quick Reference Guide personal injury e Never use the toner probe or test leads if they A Safety Information are damaged Inspect the cases and test leads for damage before use Table 1 describes the international electrical symbols used onthe testerand EE manal e Never open the case except to change the battery no user serviceable parts are inside Table 1 International Electrical Symbols e Turn off the toner or probe and disconnect all test leads before replacing the battery Warning Risk of personal injury See explanation2. Battery Status on page 4 13 IntelliTone Pro Users Manual Accessories To order accessories Table 2 contact Fluke Networks For the latest list of IntelliTone accessories and other cable testers visit the Fluke Networks website at www flukenetworks com Table 2 Accessories Fluke Networks Model Accessory or Part Number Test lead set banana jacks to MT 8203 22 alligator clips Test lead set banana jacks to MT 8203 20 alligator clips with bed of nails Soft carrying case MT 8202 05 See text regarding probe s switch position during battery replacement ASH10 EPS Figure 5 Replacing the Battery 14 Specifications Specifications Specifications apply at 23 C 73 F unless otherwise noted Environmental and Regulatory Specifications Operating temperature 32 F to 104 F 0 C to 40 C Storage temperature 4 F to 140 F 20 C to 60 C Operating relative humidity RH without 95 50 F to 95 F 10 C to 35 C condensation 75 95 F to 104 F 35 C to 40 C Uncontrolled lt 50 F lt 10 C 15 IntelliTone Pro Users Manual IT200 Toner Electrical Specifications Tone frequencies 1 digital tone 500 kHz 1 analog tone 1 kHz Battery type and life 9V alkaline NEDA 1604A or IEC 6LR61 20 hours typical Auto power down Turns off automatically after 4 hours of inactivity IP200 Probe Electrical Specifications Tone detection Detects the IntelliTonesign
3. FLUKE networks IntelliTone Pro 200 LAN Toner and 200 Probe Users Manual August 2014 2014 Fluke Corporation All product names are trademarks of their respective companies LIMITED WARRANTY AND LIMITATION OF LIABILITY Each Fluke Networks product is warranted to be free from defects in material and workmanship under normal use and service The warranty period for the mainframe is one year and begins on the date of purchase Parts accessories product repairs and services are warranted for 90 days unless otherwise stated Ni Cad Ni MH and Li lon batteries cables or other peripherals are all considered parts or accessories The warranty extends only to the original buyer or end user customer of a Fluke Networks authorized reseller and does not apply to any product which in Fluke Networks opinion has been misused abused altered neglected contaminated or damaged by accident or abnormal conditions of operation or handling Fluke Networks warrants that software will operate substantially in accordance with its functional specifications for 90 days and that it has been properly recorded on non defective media Fluke Networks does not warrant that software will be error free or operate without interruption Fluke Networks authorized resellers shall extend this warranty on new and unused products to end user customers only but have no authority to extend a greater or different warranty on behalf of Fluke Networks Warranty support is a
4. al from an IT200 toner and a 1 kHz signal from other toners Battery type and life 9V alkaline NEDA 1604A or IEC 6LR61 20 hours typical Auto power down Turns off automatically after 1 hour of inactivity 16 Feature Compatibility IntelliTtone Toner Probe Feature Intellitone locate mode IntelliTone isolate mode Cable map validation Shield validation Analog tone 1 kHz Visual audible proximity indicators O Requires IntelliTone IP200 probe Dimensions Toner 5 54 in x 2 94 in x 1 25 in 14 1 cm x 7 5 cm x 3 2 cm Probe 8 73 in x 1 88 in x 1 26 in 22 2 cm x 4 8 cm x 3 2 cm Product Compatibility Intellitone Toner and Probe Specificatio Works with Legacy Toner or Probe Weight with battery Toner 6 0 oz 170 g Probe 4 7 oz 133 g Ns 17 IntelliTone Pro Users Manual 18
5. an active pin flashes briefly then should light for about 1 second The brief flash shows which LED is next in the sequence The probe also beeps in different tones to indicate good wiring miswires shorts and opens Miswire If one LED flashes briefly then another LED lights for one second the wire for the first LED is miswired to the pin for the second LED Short If two LEDs turn on for 1 second at the same time those two pins are shorted together If more than 2 wires are shorted together the LEDs for the shorted pins indicate opens Open If an LED flashes briefly then no LEDs turn on that pin is open Validating RJ11 and RJ45 Cable Maps C4 C 53 C2 Oi C4 C3 C2 D1 CD4 C3 C2 SN A O4 D n C 3 E KE D3 2 C D2 C 3 CH CH O A CC 24 i E L 2 C3 27 C2 2 Cu Can Ca A C4 X4 TI SE C 23 2 C 3 C A3 Cu Cu Ca CO Shield If enabled See text Figure 2 Validating Cable Maps ASHO05 EPS IntelliTone Pro Users Manual Validating the Cable s Shield To use the probe s SYNC LED for shield validation during cable map tests do the following 1 10 Remove the battery door and disconnect the battery from the probe as described under Battery Life and Replacement on page 13 Turn the probe s rotary switch to CABLE MAP Note The battery must be disconnected from the probe for at least 30 seconds Replace the battery and battery door The SYNC LED will now indic
6. ate a good open or shorted shield as described in the previous section To disable shield validation via the probe s SYNC LED do the following 1 Remove the battery door and disconnect the battery from the probe Turn the probe s rotary switch any position except CABLE MAP Note The battery must be disconnected from the probe for at least 30 seconds Replace the battery and battery door Validating Ethernet Service The toner detects link pulses for 1OBASE T 100BASE TX and 1000BASE T Ethernet service on pins 1 2 and 3 6 of its RJ45 jack 1 Tum off the toner 2 Connect the toner to the circuit as shown in Figure 3 3 Turn the toner s rotary switch to SERVICE 4 The Ethernet LED indicates service on pins 1 2 or 3 6 as shown in Figure 3 The toner checks for continuity between pins 4 5 Continuity indicates the toner is connected to a network device that is turned off The toner checks for continuity between the red and black test leads and across the middle pair of the RJ45 RJ11 jack line 1 Note If the Ethernet LED alternates between red and green the Ethernet service is Auto MDIX Validating Ethernet Service Punch down block Green service on 3 6 Red service on 1 2 Continuity or non Ethernet voltage D ge No voltage Ge e No continuity ASH01 EPS Figure 3 Validating Ethernet Service 11 IntelliTone Pro Users Manual Testing for Continu
7. ent noise The analog tone is primarily used on voice cables and on bare wire The SmartTone analog technology will change cadence when a pair is shorted at the far end This makes exact pair identification easy and precise Intellitone Pro 200 LAN Toner IntelliTone Pro 200 Probe The IntelliTone feature also lets you use the toner and probe to validate and troubleshoot wiring on RJ11 and RJ45 cables The toner detects Ethernet service_and indicates active pair number on Ethernet circuits The toner and probe also provide standard functions such as visual and audible signal strength indication digital toning detection SmartTone analog toning detection and continuity testing Registration Registering your product with Fluke Networks gives you access to valuable information on product updates troubleshooting tips and other support services To register fill out the online registration form on the Fluke Networks website at www flukenetworks com registration IntelliTone Pro Users Manual Contacting Fluke Networks For technical support please contact us via support flukenetworks com a www flukenetworks com Z support flukenetworks com T 1 425 446 5500 e Australia 61 2 8850 3333 or 61 3 9329 0244 e Beijing 86 10 6512 3435 e Brazil 11 3759 7600 e Canada 1 800 363 5853 e Europe 31 0 40 2675 600 e Hong Kong 852 2721 3228 e Japan 03 6714 3117 e Korea 82 2 539 6311 e Singapore 65
8. he toner or probe turn the rotary switch to any position except OFF Locating and Isolating Terminated UTP STP Cables with the IntelliTone The IntelliTone Pro toner provides two toning modes for locating and isolating cables one digital tone Zeg and one SmartTone 1kHz analog tone WII With the toner set to digital tone mode the probe can be set to either locate or isolate gt Both toning signals are available at all connectors on the toner The digital tone js optimized for 4 pair UTP data environments and the SmartTone analog tone WI is optimized for two wire locating To locate and isolate cables using the digital tone do the following 1 Connect the IT200 toner to a jack or punch down block as shown in Figure 1 2 Turn the toner s rotary switch to 3 Turn the IP200 probe s rotary switch to locate 4 Use the probe to find the general location of the tone at a cable rack patch panel or behind a wall The SYNC LED lights up green when the probe is receiving the IntelliTone signal Locating and Isolating Terminated UTP STP Cables with the IntelliTone In locating mode the probe s LEDs light up from 1 to 8 as the signal strength increases The higher the number the stronger the signal Note If you cannot locate the IntelliTone signal on 2 conductor cables the cable may be shorted Use the cable map test page 8 to test for shorts on cables with RJ11 and RJ45 connectors Use the c
9. ity You can use the toner to test circuits and components for continuity 1 12 If you are testing a circuit verify that it is not powered Use the toner s continuity O function to check for continuity Use a voltage meter to check other types of circuits for power Turn off the toner Connect the toner to the circuit or component as shown in Figure 4 Turn the toner s rotary switch to Q The LED indicates an open or closed circuit as shown in Figure 4 Figure 4 Continuity Test ASHO9 EPS Maintenance Clean the case with a soft cloth dampened with water or a mild soap solution dh Caution To avoid damaging the case do not use solvents or abrasive cleansers Battery Life and Replacement The toner and probe batteries last for about 20 hours of typical use Figure 5 shows how to replace the battery in the toner and probe Note The position of the probe s rotary switch when the battery is replaced enables or disables shield validation for cable map tests See Validating the Cable s Shield on page 10 Maintenance AN Warning To avoid possible electric shock or personal injury Turn off the toner or probe and disconnect all test leads before replacing the battery Use only a 9 V battery properly installed in the case to power the toner and probe dh Caution To avoid unreliable test results replace the battery as soon as the low battery indication appears See
10. lead must be connected to the other wire of the pair Put the toner and probe in the wll position At the far end of the cable run place the probe near the wires you are tracing Pick the pair that gives the loudest signal in the toner speaker Short and release the two wires of the pair If you hear a change in the pattern of the tone then you have located the target pair of wires If you don t hear a change in the tone pattern then pick a different pair and try again until you find the pair that causes the tone pattern to change IntelliTone Pro Users Manual Validating RJ11 and RJ45 Cable Maps You can use the IT200 toner and IP200 probe to validate the cable map on RJ11 and RJ45 connectors The cable map function finds the most common wiring faults on twisted pair cabling shorts opens and crossed pairs 1 Connect an IT200 toner to a RJ11 or RJ45 jack as shown in Figure 2 Turn the toner s rotary switch to If necessary use the IP200 probe to locate the correct connector at the other end of the cabling as described in the previous section Connect the IP200 probe to the RJ11 or RJ45 jack then turn the probe s rotary switch to CABLE MAP The probe s LEDs and beeper indicate the cable map as follows e The number of each LED corresponds to a pin on the connector You can enable the SYNC LED to validate the shield See Validating the Cable s Shield on page 10 Each LED that corresponding to
11. ontinuity test page 12 to check for shorts on coax and non terminated cables 5 Turn the probe s rotary switch to gt isolate 6 Use the probe to isolate the tone source in the cable bundle or at the patch panel The SYNC LED lights up green when the probe is receiving the IntelliTone signal In isolating mode the probes LEDs light up from 1 to 8 as the signal strength increases IntelliTone Pro Users Manual Connecting the Toner Locating Cables Isolating Cables JOM SmartTone Analog 1kHz toning Ba EE 32 3 R a ce AN ii Digital toning ASH04 EPS Figure 1 Locating and Isolating Cables Isolating Individual Wire Pairs with the SmartTone Analog Function Isolating Individual Wire Pairs with the SmartTone Analog Function The Wl position on the IntelliTone probe and toner lets you use the probe to trace using an analog 1kHz tone SmartTone is intended for use on dry pairs of wires that are un terminated at both ends of the run It is not intended to be used on live wires with a DC power source e g live telephone lines nor will it work on wire pairs that are carrying AC signals SmartTone works on many types of wire pairs including twisted pair house wiring and coax the shield is one wire and the center conductor is the other wire of the pair SmartTone Positive Identification 1 The toner red lead must be connected to one of the wires of the pair and the black
12. rges FOB Shipping point THIS WARRANTY IS BUYER S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE FLUKE NETWORKS SHALL NOT BE LIABLE FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES INCLUDING LOSS OF DATA ARISING FROM ANY CAUSE OR THEORY Since some countries or states do not allow limitation of the term of an implied warranty or exclusion or limitation of incidental or consequential damages the limitations and exclusions of this warranty may not apply to every buyer If any provision of this Warranty is held invalid or unenforceable by a court or other decision maker of competent jurisdiction such holding will not affect the validity or enforceability of any other provision 4 04 Fluke Networks PO Box 777 Everett WA 98206 0777 USA Contents Title Page Overview of Features ET 1 REJST AION EE 1 Contacting FOKE NETWORKS EE 2 Beie Te a ue EE 2 E200 intelli Prone Feet tege E Ee Madaalete EE Et Een 2 IT200 IntelliTone Pro LAN Toner mgceegeienresebeeugge g t Stied Guerre Sheet 2 IPZO0 Intelli tone Fre Probe enee ees deiv el eed ENNER 3 A safety Jet rd EE 3 Battery E TE 4 PLUTO SP OWN DOWR WEE 4 Locating and Isolating Terminated UTP STP Cables with the IntelliTone 4 Isolating Individual Wire Pairs with the SmartTone Analog Function sssssseseeess
13. s in the manual e Use only a 9V battery properly installed in the case to power the toner and probe Caution Risk of damage or destruction to i WW equipment or software See explanations in the e If this equipment is used in a manner not specified manual by the manufacturer the protection provided by the equipment may be impaired A AN Warning Risk of electric shock This equipment not for connection to public Caution communications networks such as active communi systems e Avoid touching the probe tip to patch panel connections and using the tip to dig into cable X Do not put circuit boards in the garbage Dispose bundles Doing so regularly may damage the of circuit boards in accordance with local probe tip over time regulations e To avoid unreliable test results replace the Meets RCM standard battery as soon as the low battery indication Europeenne appears IntelliTone Pro Users Manual Battery Status LEDs on the toner and probe light for 1 second at power on to indicate the battery status SYNC GE Toner battery status Probe battery status LED LED Green Battery is good Yellow Battery is marginal Red Battery is low See Battery Life and Replacement on page 16 for more information on the battery Auto Power Down The toner turns off automatically after approximately 2 V2 hours of inactivity The probe turns off automatically after 1 hour of inactivity To reactivate t
14. ssn 7 SMartTone Positive Identification seere a a 7 Validating RIIT and RJ45 Cable Maps sssssssssssnsssssssssnsssrnrnnnrnrrnnnnsssnrnnrnnnrrnnennenrnnnnnnnnne 8 IntelliTone Pro Users Manual Validating tne Gable s TE e WEE 10 Validating Ethernet Service ccccccccsssseseseeeeeeeeeeeeeeeaeasseseeeeeeeeesesseaaaaaaeeeeeeeeeeesaneaaaaaes 11 E ele Wu e eege EE 12 Maintenance EE 13 Battery Life and Replacement ccccccccccccccceeeecceeeeceeeeeeeeeeeeeeeeeeaaeeeeeeeeeeeeaananaaanaanes 13 ACCESSO ES begeestert ee 14 Si Re le ee EE 15 IT200 Toner Electrical Specifications cccceeeseeeeceeeeeeecceeaeeeeseeeeeeeeesseesanaaseeeeeeeess 16 IP200 Probe Electrical Specifications ccceseseseeccceeeeeeeeeeseeseeeceeeeeeseeesenaaseeeeeeees 16 FEaLUre COMPa ClO UE 17 DIMENSIONS oase a a a 17 Weight EELER errien E a O 17 Overview of Features The IntelliTone Pro 200 LAN toner and Pro 200 probe let you locate isolate and validate twisted pair UTP Cat 5e Cat 6 coax cables RG6 RG59 and others for CATV CCTV bare wire such as speaker wire and security network wire and Cat 3 telephone cabling The toner also lets you validate data services The toner and probe feature both digital and analog toning and detection The digital IntelliTone tone is primarily used on data cables and on active networks In these environments the digital signal eliminates cable misidentification due to signal bleed and radiated or ambi
15. vailable only if product is purchased through a Fluke Networks authorized sales outlet or Buyer has paid the applicable international price Fluke Networks reserves the right to invoice Buyer for importation costs of repair replacement parts when product purchased in one country is submitted for repair in another country Fluke Networks warranty obligation is limited at Fluke Networks option to refund of the purchase price free of charge repair or replacement of a defective product which is returned to a Fluke Networks authorized service center within the warranty period To obtain warranty service contact your nearest Fluke Networks authorized service center to obtain return authorization information then send the product to that service center with a description of the difficulty postage and insurance prepaid FOB destination Fluke Networks assumes no risk for damage in transit Following warranty repair the product will be returned to Buyer transportation prepaid FOB destination If Fluke Networks determines that failure was caused by neglect misuse contamination alteration accident or abnormal condition of operation or handling or normal wear and tear of mechanical components Fluke Networks will provide an estimate of repair costs and obtain authorization before commencing the work Following repair the product will be returned to the Buyer transportation prepaid and the Buyer will be billed for the repair and return transportation cha
Download Pdf Manuals
Related Search