LIN Fiber Optic Bridge User Manual – Version 2.0
Contents
1. and 5 p m Eastern Time You may also fax or e mail your questions to us Please include your voice telephone number for prompt assistance Phone 248 488 2080 Fax 248 488 2082 E mail techsupp dgtech com Web site http www dgtech com 1 5 Related documents N LIN Specification Package Dearborn Group Technology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 1 6 LIN FO Satellite Module EMC compliance The LIN Fiber Optic satellite module has been independently tested to the GMW 3097 Feb 2004 REV 4 EMC specification The following test methods were tested without any non compliances 3 3 1 Radiated Emissions Absorber Lined Shielded Enclosure ALSE 3 4 1 Radiated Immunity Bulk Current Injection 3 4 3 Radiated Immunity Reverberation Chamber Mode Tuning IMPORTANT Please read the following before using the fiber optic Product Dearborn Group Technology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 2 Fiber Optic Bridge Adapter Figure 2 that follows depicts the front label of the LIN Fiber Optic Bridge Adapter F O MODE WIRE MODE L LI Ld 2 LED 3 LED 4 LIN Fiber Optic Bridge see other side for connector and switch details Cable 1 FO Cable 2 Dearborn Group http www dgtech com 3 Figure 2 Front label for the LIN Fiber Optic Bridge Adapter Attention When connecting the fiber optic cables always connect Cable2. 1 of the Bridge to Cable 1 of the Satellite and likewise Cable 2 to Cable 2 and Cable 3 to Cable 3 Please see Figure 3 on page 15 for a view of the label for the Satellite Module Reference note Older labels for the Satellite Module and Bridge identified the cables as Rx Tx and vs Cable 1 2 and This resulted in some confusion regarding the proper connections between the two units and therefore the designations were changed to Cable 1 Cable 2 and Cable 3 on the latest Satellite Module and FO Cable 1 FO Cable 2 and FO Cable 3 on the Bridge Adapter Dearborn Group Technology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 2 1 Power switch This switch is used to apply disconnect power to the LIN Fiber Optic Bridge Power to the unit is applied when the switch is placed in the up position Please note that any change in the Configuration Dip switches will require a Power Cycling Turn Power Switch OFF and then On of the Fiber Optic Bridge Adapter 2 2 Power jack This standard 2 5 mm connector with positive center pin is used to provide power to the LIN Fiber Optic Bridge This power jack is designed to accept an input range between 8 to 18 VDC The typical operating voltage supplied by the included Universal Power Adapter is approximately 12 VDC ATTENTION FUSE FAILURE If the Bridge adapter appears dead check the fuse to see if it has opened the circuit It is located on the to
3. 1 Typical Setup for a Fiber Optic Bridge ATTENTION NOTE The need for Fiber Optic Satellite Module Isolation The FO SAT Modules need to be isolated by 50mm This applies to all satellite modules and is not specific to DG s The reason is the bypass capacitors typically are placed inside the fiber optic satellite modules from inputs to the Printed Circuit Board Chassis If the case of the fiber optic module is placed directly on the ground plane and there are bypass caps inside the satellite module from input to chassis then there is an additional RF path provided to travel This path can cause different behavior and is what is being avoided by isolating the fiber optic module by 50mm insulation above the ground plane Dearborn Group Technology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 1 3 Package contents The Fiber Optic Satellite Module package includes the following items LIN Fiber Optic Bridge including a 12 VDC Universal A C power adapter LIN Fiber Optic Satellite Module nine volt batteries not included Three fiber optic cables with SMA connectors 10 meters in length CD with the user Manual for the Fiber Optic Bridge If you discover that you are missing any part of this package please contact your Dearborn Group sales representative or the technical support hotline at once 1 4 Technical support In the U S technical support representatives are available to answer your questions between 9 a m
4. AN Low IN Pin 3 1850 Bus Pin 1 K Line L L Pin 5 Ground Pin 6 LIN Bus NOTE This is a DB 9 Male connector Only connect these pins when powered from the Bridge Adapter s Power Adapter Connector Fiber Optic Satellite Module Used with the Fiber Optic Bridge Pin Assignments Pin 6 CAN High Pin 2 J1850 Bus Pin 5 Ground Pin 4 VBAT L LIN Pin 5 Ground Pin 8 LIN Bus NOTE This is a High Density DB 15 Female connector Only connect these pins when powered from the Bridge Adapter s Power Adapter Connector Dearborn Group Tech n ology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 20
5. Dearborn Group l echnology LIN FIBER OPTIC BRIDGE USER MANUAL Satellite Module and Bridge Adapter Version 2 0 2008 Dearborn Group Inc 27007 Hills Tech Court Farmington Hills MI 48331 Phone 248 488 2080 FAX 248 488 2082 http www dgtech com This document is copyrighted by the Dearborn Group Inc Permission is granted to copy any or all portions of this manual provided that such copies are for use with the product provided by the Dearborn Group and that either the name s Dearborn Group Inc and or Dearborn Group Technology is retained on all copies as on the original IMPORTANT NOTICE It is essential that you read this document carefully before using the Fiber Optic products Damage caused by misuse of this product is not covered by the seller s product warranty When using this manual please remember the following e This manual may be changed in whole or in part with or without notice e Dearborn Group Inc assumes no responsibility for any damage resulting from any accident or for any other reason while the Fiber Optic products are in use e Specifications presented herein are for illustration purposes only and do not necessarily represent the latest revisions of hardware Dearborn Group Inc assumes no responsibility for any intellectual property claims that may result from use of this material e No license is granted by implication or otherwise for any patents or any oth
6. age to the hardware 3 3 Optical Connectors These SMA connectors are used to connect the LIN Fiber Optic Satellite Module to the LIN Fiber Optic Bridge using the supplied optic cables each 10 meters in length NOTE To ensure reliable data transmission the length of each fiber optic cable used should not exceed 100 meters Dearborn Group Technology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 17 3 3 4 Fiber Optic and Copper wire connections linking the LIN Bridge to the DUT See Table 6 for the fiber optic connections between the Bridge Adapter and the Satellite Module and for the copper wire connections between the Satellite Module and the DUT Fiber Optic Cables Bridge to Satellite DB 15 Satellite Connector to DUT wired Connect Cable 1 to Cable 1 Pin 4 VP Connect Cable 2 to Cable 2 Pin 5 Ground Connect Cable 3 to Cable 3 Pin 8 LIN Bus Table 6 Fiber Optic and Copper Connections to Satellite Module 3 3 2 Fiber Optic connections The fiber optic cable needed for connecting the units is a 100 140 Micro multimode fiber optic cable with SMA connectors Please see Figure 2 as a reference in connecting the fiber optic cables 3 4 Synchronization and Slew Rate indicators for Satellite Module This status LED closest to the power switch will flash for approximately 1 2 seconds at power up as synchronization occurs between the Satellite Module and Bridge Adaptor The
7. csaisssasasansaannsodosessssesennnddcnensenenerssneieiieaesesesaas 15 3 1 1 Power to Satellite 76 3 12 76 3 2 DB 15 CONNGCIOR 16 3 3 Optical 17 3 3 1 Fiber Optic and Copper wire connections linking the LIN Bridge to the DUT 18 3 3 2 Fiber Optic CODheCllOTliS iiiieiieso e oie oo ee eie poen ena EE p Ee ea pasa vea eee F oaa SERRE E Per 18 3 4 Synchronization and Slew Rate indicators for Satellite Module 18 Dearborn Group Technology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 3 5 Configuration and Battery Low indicators for Satellite Module 18 APPENDIX A FIBER OPTIC BRIDGE PIN ASSIGNMENTS 20 Dearborn Group Technology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 1 Product Overview Getting Started Dearborn Group supports several interfaces for use in an EMC test environment These products using fiber optic cabling provide vehicle network connectivity to device s under test DUT The Fiber Optic Bridge Local Interconnect Network LIN System Part number DG FO BRIDGE L consi
8. earborn Group Tech nology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 11 25 LED indicators for configuration The LIN Fiber Optic Bridge has four LEDs that indicate the system status and configuration See Table 2 below for a description of these indications Fiber Optic Side DUT LED Color Green Red Off LED Position LED Meaning LED 1 Master pull up resistor IN Master pull up resistor OUT Battery Low LED 2 Slew rate Fast Slew rate Slow Slew rate Normal Copper Wire Side Host LED Position LED Meaning LED 3 Slew rate Fast Slew rate Slow Slew rate Normal LED 4 Master pull up resistor IN Master pull up resistor OUT Battery Low Table 2 Fiber Optic Bridge LED Indications 2 6 Configuring DIP switches for the Host system copper side This DIP switch bank is used to configure the copper side of the LIN Bus There are three slide switches the up position is on and down position is off This switch bank is located on the right end of the Bridge while viewing the product label normally See Table 3 below for the DIP switch options Note The default setting is for all three switches to be in the off position when the product Table 3 DIP Switch Selections Host Dearborn Group Technology is shipped DIP Switch Selections copper wire side Functional Config
9. er rights of Dearborn Group Inc or of any third party GRYPHON is a registered trademark of Dearborn Group Inc All other products referenced in this manual are trademarks of their respective manufacturers Dearborn Group Technology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 Table of Contents PRODUCT OVERVIEW GETTING STARTED 5 1 1 Fiber Optic Bridge Functions Features 5 1 2 Typical usage of a LIN Fiber Optic Bridge 6 1 3 Package CNIS 7 1 4 Technical support 7 15 Related COCUMEINS ere ote inu cu dev VO vw uM UG 7 1 6 LIN FO Satellite Module EMC 8 FIBER OPTIC BRIDGE 9 2 1 c p ELE 10 PAP OWT FAH e E 10 2 3 DBBO9COBDDOCIOE eoe ioo neci iras ds cacadiaasocsnmanhhidadnastenneeieeareatoccees 11 2 4 Fiber Optical 11 2 5 LED indicators for configuration eese eene 12 2 6 Configuring DIP switches for the Host system copper side 12 2 7 Configuring DIP switches for the Satellite system fiber optic side 13 FIBER OPTIC SATELLITE MODULE 15 31 cctiscscansi
10. ic Satellite Module Isolation The FO SAT Modules need to be isolated by 50mm This applies to all satellite modules and is not specific to DG s The reason is the bypass capacitors typically are placed inside the fiber optic satellite modules from inputs to the Printed Circuit Board Chassis If the case of the fiber optic module is placed directly on the ground plane and there are bypass caps inside the satellite module from input to chassis then there is an additional RF path provided to travel This path can cause different behavior and is what is being avoided by isolating the fiber optic module by 50mm insulation above the ground plane 3 4 Power Switch This switch marked I O PWR on the label above it is used to turn power on or off to the LIN Satellite Module Power is applied to the unit when the switch is moved to the left D and power off to the right O Dearborn Group Technology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 15 3 1 1 Power to Satellite Module Power is supplied to the Fiber Optic Satellite Module via two internal nine volt batteries and may be turned on or off via the toggle switch see Section 3 1 above 3 1 2 Battery compartment The Fiber Optic Satellite Module is powered by two nine volt batteries inserted into the battery compartment and connected as indicated on the label of the module 3 2 DB15 Connector This connector is used to connect the LIN Fiber Optic Satellite Mod
11. p circuit board in a fuse socket near the ON OFF switch The fuse in the bridge is a commonly available type Littlefuse sells the product under the Nanofuse name The fuse in the bridge is a slow blow 1 5A fuse Digikey part number F2601 Other companies also sell compatible fuses Dearborn Group Tech nology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 10 2 3 DBO9connector This connector is used to connect the host controller to the LIN Fiber Optic Bridge Table 1 below provides the pin assignments for the DB 9 male connector on the LIN Bridge Adapter that connects to the host test device LIN Protocol Bridge Adapter DB 9 Connector male Pin Number Function Remarks 5 Ground Connect to Ground of Host 6 LIN Bus Connect to LIN Bus of Host All other pins N A Make no connection to these pins Table 1 Pin Assignments for LIN Bridge Adapter for connections to Host 2 4 Fiber Optical connectors These three connectors are used to connect the LIN Fiber Optic Bridge to the LIN Fiber Optic Satellite Module using the supplied 10 meter length fiber optic cables Note To ensure reliable data transmission the length of each cable used should not exceed 100 meters Reminder note When connecting the cables between the Bridge and Satellite Module always connect Cable 1 to Cable 1 Cable 2 to Cable 2 and Cable 3 to Cable 3 See Figures 2 and 3 for a view of the labels for the respective units D
12. reafter this LED will provide the user information regarding the selected slew rate wherein red slow green fast and off unlighted normal Note The default slew rate is normal and is the most commonly used Please note that not all LIN transceiver Integrated Circuits support the fast slew rate 3 5 Configuration and Battery Low indicators for Satellite Module This status LED farthest from the power switch also serves as a multifunction indicator Red indicates the unit is functioning in a Slave mode while green indicates Master mode Dearborn Group Technology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 18 During operation this LED will always be illuminated either red or green unless there is a low battery condition in which case the LED will be turned off When this LED is no longer illuminated i e turned off it indicates that the enclosed batteries are not providing sufficient power for the proper operation of the module and the batteries should be replaced Important Do not attempt to run further tests until the batteries have been replaced Dearborn Group Technology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 19 APPENDIX A Fiber Optic Bridge Pin Assignments FO Bridge Adapters and supported FO Satellite Modules NOTE Fiber Optic Bridge Released Version FY 2007 and later Pin Assignments Voltage supplied by Power Adapter Connector Pin 2 C
13. s switched IN or OUT depending upon the need for the DUT to have this load included e g a slave DUT may need this load switched IN while a master DUT may not Switching this load resistor IN when not needed could result in a reduction of battery life for the Satellite Module Remember If the DIP switches are changed power must be recycled on the LIN Fiber Optic Bridge to enable the changes The LEDs will flash for several seconds and then stabilize to the selected mode of operation as shown by the color state of each LED Dearborn Group Tech nology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 13 Note Changes made to the left side DIP switches control the configuration of the LIN Fiber Optic Satellite Module This feature allows you to change the configuration without having to enter the test chamber The changes are transmitted to the Satellite Module via the fiber optic communications channel Cable 3 Dearborn Group Technology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 14 3 Fiber Optic Satellite Module The LIN Fiber Optic Satellite Module is normally placed inside of the test chamber although it is often used for tests performed outside the chamber as well Figure 3 that follows depicts the label for the LIN Fiber Optic Satellite Module LIN J 2602 Fiber Optic Satellite Module Figure 3 LIN Fiber Optic Satellite Module NOTE The need for Fiber Opt
14. sts of two major components e A Fiber Optic Bridge Adapter The component connected to a Tester outside of an EMC chamber e A Fiber Optic Satellite Module The component inside the EMC chamber connected to the device under test 11 Fiber Optic Bridge Functions Features The Bridge Adapter works as a pass through hardware device It translates the vehicle network electrical signals from a user s host test device such as the GRYPHON tool into fiber optic signals These fiber optic signals are used to interface with the Satellite Module placed in the EMC Test Chamber The fiber optic signals are then translated back into vehicle network electrical signals by the Satellite Module and used to communicate with the DUT Hardware features of the Satellite Module Anodized aluminum enclosure Anteroom with feed through capacitors SMA Fiber Optic connectors Indicators for slew rate and configuration Powered via two internal nine volt batteries Low battery status indicator Hardware dimensions of the Satellite Module Housing Height 1 Width 6 Depth 2 3 Dearborn Group Technology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 1 2 Typical usage of a LIN Fiber Optic Bridge EMI EMC Test Chamber Fiber Optic cables DG Fiber Optic Customer Bridge dri Adapter LIN Bus Pin 8 VBat Pin 4 GND Pin 5 Copper connection DB9 output to external tester LIN Bus Pin 6 GND Pin 5 Figure
15. ule to the DUT Device Under Test Table 5 provides the DB 15 H D female connector pin assignments used to connect the Satellite Module to the DUT The purpose of the V9 connection between the DUT and the Satellite Module is to power the LIN transceivers residing in the Satellite Module This is necessary in order to conserve battery power from the nine volt batteries enclosed in the Satellite Module that power the fiber optic isolation for the communications necessary for the testing process ATTENTION The DUT cannot be powered from the LIN Satellite Module Important All three connections indicated in Table 5 below must be made between the Satellite Module and the DUT Caution Making a connection to any of the other pins of the DB 15 connector could result in damage to the equipment Dearborn Group Tech nology User Manual Version 2 0 LIN Fiber Optic Bridge 2008 16 LIN Protocol Satellite Module DB 15 Connector high density female Pin Number Function Remarks 4 VP T Connect to of DUT 5 Ground Connect to Ground of DUT 8 LIN Bus Connect to LIN Bus of DUT All other pins N A Make no connection to these pins Table 5 LIN Satellite Module Pin Assignments for Connections to DUT Make only the connections to the DB 15 and DB 9 connectors as indicated in Tables 1 and 5 above Other pins contain signals and voltages and any connection made to them could cause dam
16. uration for Host Soren 0 Off On Off On Off On Slew rate Slow X X Slew rate Fast X X Slew rate Normal X X Master pull up resistor switched IN X Master pull up resistor switched OUT X User Manual Version 2 0 LIN Fiber Optic Bridge 2008 12 Important If the DIP switches are changed power must be recycled on the LIN Fiber Optic Bridge to enable the changes The LEDs will flash for several seconds and then stabilize to the selected mode of operation as shown by the color state of each LED 2 7 Configuring DIP switches for the Satellite system fiber optic side This DIP switch bank is used to configure the fiber optic side of the LIN Bus There are three slide switches the up position is and down position is off This switch bank is located on the left end of the Bridge while viewing the product label normally See Table 4 below for the DIP switch options Note The default setting is for all three switches to be in the off position when the product is shipped DIP Switch Selections fiber optic side 2 Switch 1 Switch 2 Switch 3 Functional Configuration for DUT Off On Off On Off On Slew rate Slow X X Slew rate Fast X X Slew rate Normal X X Master pull up resistor switched IN X Master pull up resistor switched OUT X Table 4 DIP Switch Selections Satellite Note The Master pull up resistor i
Download Pdf Manuals
Related Search