English owner`s manual
Contents
1. left channel speaker output and the right channel speaker output Each output channel is designed to power one speaker The negative terminal of your loudspeaker terminal should be connected to_the speaker terminal on the Sonata marked as zero 0 and the positive terminal of your loudspeaker should be connected to the terminal on the Sonata that corresponds to the loudspeaker s nominal impedance 4 or 8 ohms If your speaker has nominal impedance of 6 ohms you can connect it to either of the two outputs You should try using each setting and select the one that performs better with your speakers Make sure to prevent a short circuit at the amplifier s speaker terminals as this will damage the amplifier Never run the amplifier without speakers connected since that may damage the transformers Powering ON and OFF When turning the unit on make sure the volume control is at its lowest setting the volume control is at minimum when turned counterclockwise to the mechanical limit At the end of your listening session make sure to turn the amplifier off Leaving it on does nothing for sound quality and it reduces life of the vacuum tubes The amplifier should always be turned on and off via its own power on off switch Tube Replacement Your Sonata amplifier was designed to maximize the life of the tubes You can expect that your EL34 power output tubes should last approximately 1200 hrs while the ECC82 input stage tubes should last2. approximately 2500 hrs We strongly recommend replacing the EL34 output tubes at 12 18 months intervals depending on your listening habits and the ECC82 input stage tubes at every other power tube replacement every 24 36 months This will ensure that the amplifier always performs at its best and tube failure will not overstress other parts Only matched pairs of EL34 output tubes should be used for each channel Servicing Because of its careful design and high manufacturing standards your Sonata amplifier should normally require only minimal service to maintain its high level of performance CAUTION Lethal voltages are present inside the amplifier Do not remove the amplifier s bottom cover and do not tamper with components inside the unit even with the power turned off Servicing should be left only to authorized and trained personnel Technical Specifications Output power 2x35W Class of operation A 0 20W AB 20 35W Configuration Push Pull Tubes 4x EL34 two matched pairs 4x ECC82 Inputs 3 single ended Outputs Can drive 4 or 8 ohm loudspeakers Input sensitivity 0 7Vrms for full power THD 0 03 1W 1KHz 3 30W 1KHz Frequency bandwidth 10Hz 1dB 60KHz 3dB S N ratio 78dB Input impedance 100K Input voltage 240V 50Hz option 120V 60Hz North America Power consumption 200VA Dimension 17 W x 11 5 D x 6 H Weight approx 35 lbs
3. listening experience The WLM Team SAFETY PRECAUTIONS CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT OPEN YOUR WLM SONATA THERE ARE NO USER SERVICEABLE PARTS INSIDE PLEASE CONTACT YOUR DEALER DISTRIBUTOR IF THERE IS EVER NEED FOR SERVICE 1 Read this User s Manual and refer to it frequently during use of this product All the safety and operating instructions should be read before the product is operated 2 Retain this User s Manual The safety and operating instructions contained in this manual should be retained for future reference 3 Follow Instructions All operating procedures and instructions should be closely followed 4 Power Sources This product should be operated using only the type of power source specified on the label next to the power input connector 5 Grounding This product is equipped with a three prong IEC connector Always use a power cord and an electrical outlet that is properly grounded If you do not know whether the outlet is grounded consult your electrician or local power company 6 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched Always use power cords with adequate current ratings and safety certifications UL CE TUV CSA etc 7 Fuses For continued protection against fire hazard replace fuses with the same type and rating of the fuses specified When changing fuses completely unplug the AC cord fro
4. VWILINI ACOUSTICS Souata Vacuum Tube Integrated Amplifier Owner s Manual Dear Customer We at WLM would like to take this opportunity to thank you for purchasing the Sonata vacuum tube integrated amplifier The Sonata was created for you the music connoisseur in search of an extraordinary listening experience dependability and high value Your Sonata was 100 designed and manufactured in Europe and demonstrates the finest level of craftsmanship throughout Sonically the Sonata presents to the listener an emotionally supercharged effortless musical presentation that easily competes with competition costing many times more The people that stand behind your amplifier draw on more than a decade of professional electronics design and manufacturing experience We are all committed to providing our customers with extraordinary sound reproduction at affordable prices We have achieved this goal through modern design high quality parts expert components sourcing and efficient manufacturing We are confident that your Sonata will give you many years of listening pleasure Before using your Sonata please take the time to carefully read and understand the safety instructions and operating procedures in this owner s manual Becoming familiar with all details about your Sonata amplifier will ensure safe usage and reliable operation The effort you invest now will be well rewarded as the time goes by Thank you and enjoy your
5. ay cause loss of contact and it may be necessary to reinsert tubes to restore the good connection 4 Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a dry cloth for cleaning Do not use any type of abrasive pad scouring powder or solvent such as alcohol or benzene Getting Started About Your Amplifier Your Sonata amplifier was designed to provide a significant value based on a high performance to price ratio Two matched pairs of EL34 power output tubes and four ECC82 input stage tubes are used by your Sonata which operates in Class A for the first 20 watts RMS per channel and in Class AB up to 35 watts RMS per channel All parts have been carefully chosen for the optimum sound quality and the overall circuit layout is maximized for sonic purity Construction and Testing Your Sonata amplifier has been carefully built by highly skilled European craftsmen To assure consistent performance each Sonata amplifier goes through extensive electrical testing before being shipped This time consuming perfectionist approach in the design and manufacturing of audio equipment is intended to provide the best in musical satisfaction with lasting value Handling Vacuum Tubes Many people have never had experience handling vacuum tubes The process is very similar to handling incandescent light bulbs As with light bulbs you should not touch a vacuum tube when it is operating sin
6. ce you can burn yourself Similarly if a tube is dropped on a hard surface it will break When replacing the tubes allow sufficient time a minimum of 15 minutes for the tubes to cool down and internal capacitors to discharge Before you insert a tube you should make certain the unit is disconnected from the AC outlet and that the tube has cooled down Inspect the tube for cracks and physical damage Make sure that the pins are straight If you need to straighten the pins be very careful as it may cause the glass envelope to break causing the tube to lose the vacuum and fail as soon as the amplifier is powered on Carefully align the pins with the socket and gently insert the tube Never force a tube into a socket Packaging Save all the packaging in a dry place Your Sonata amplifier is a precision electronic instrument and should be properly packaged any time shipment is made Because of its weight it is highly probable that the unit will be damaged during shipment if repackaged in a box and packing other than that designed for the unit Preparation for Use Place your Sonata amplifier on a flat surface Your Sonata amplifier is delivered with two matched pairs of EL34 output tubes It is important to follow markings on the tube boxes and insert them into appropriate sockets Your Sonata amplifier utilizes auto biasing circuitry so you never need to be concerned with the inconveniences of biasing the tubes Before inserting the tubes in
7. hat could obstruct the airflow and cause overheating 3 Surface Place the unit on a flat level surface Care should be taken to prevent objects from falling and liquids from spilling into the unit Do not subject the unit to excessive smoke dust vibration or shock SERVICE AND MAINTENANCE 1 Replacement Parts Unauthorized part substitutions may result in fire electric shock and degradation of audio performance Modifications are discouraged and will void your warranty 2 Tube Replacement Rolling It is recommended to replace the EL34 output tubes at 12 to 18 month intervals depending on your listening habits and the ECC82 input signal tubes at every other output tube replacement 24 36 months This will ensure best performance and avoid tube failure which could overstress other parts When it is time to replace your tubes remove the AC power plug from the wall and allow for at least 15 minutes for the tubes to cool and the internal high voltage capacitors to discharge Follow instructions outlined in this manual Frequent replacement of tubes for experimenting purposes is not recommended as tube sockets are sensitive mechanical parts and frequent insertions can cause premature failure and loss of contact which may result in amplifier damage and degradation in performance 3 Tube Socket contacts Tube pins and socket contacts are subject to oxidation If the amplifier is not used for several days at a time the oxidation m
8. m the wall outlet 8 Tubes During operation the tubes get very hot Do not touch the tubes since this may result in a severe burn Allow at least 15 minutes after removing power for tubes to cool down before touching them 9 Turn off when not using Turn off the unit as soon as you stop actively using it Unplug the power cord from the wall during a lightning storm or when the product is to be left unattended and unused for longer periods of time ENVIRONMENT 1 Water and Moisture Do not use this product near water Damp rooms and basements should be avoided 2 Heat This product should be situated away from heat sources such as radiators heat registers stoves ot other appliances that produce heat Also avoid putting the unit in the direct rays of the sun 3 This product is designed for indoor use only PLACEMENT 1 Accessibility It is normal for a vacuum tube power amplifier to run warm if used for prolonged periods Tubes are very hot when operating and should not be touched for at least 15 minutes after the unit is turned off to prevent burns Always place your amplifier away from children and pets to prevent burns 2 Ventilation Do not place your amplifier in a closed area e g bookcase as overheating could occur Ensure that there is at least 8 200mm of open space above the amplifier Also make sure that the the vents on the bottom of the amplifier are not covered Never place anything on top of your amplifier t
9. spect them for cracks and physical damage Make sure that the pins are straight If you need to straighten the pins be very careful as that may cause the glass envelope to break causing the tube to lose the vacuum and fail as soon as the amplifier is powered on Carefully align the pins with the socket and gently insert the tube fully into the socket Never force a tube into a socket Controls and their Functions Front Panel Selector Switch The three position selector switch is used to select the active audio source Volume control This control is used to adjust the output sound level Turning the control knob clockwise increases the sound level and turning it counterclockwise decreases the sound level RIGHT SPEAKER LEFT SPEAKER oy 7 4 8 0 4 8 WMILIM mase in europe C Back Panel Power Switch Press the power switch to the I position to turn the power on Within 10 20 seconds as the tube heaters reach operating temperature the tubes will begin to glow a soft orange light The red LED on the front panel will glow to indicate the unit is on Press the power switch to 0 to turn the unit off As the heaters cool off the orange glow will slowly disappear as will the red LED on the front panel Audio signal connection jacks Use these jacks to connect the audio interconnects from your source components to the amplifier Speaker terminals Your Sonata amplifier is stereo two output channels There is a
Download Pdf Manuals
Related Search