instruction manual
Contents
1. ES USER S MANUAL version 1 1 AWST 8802 WIRELESS DUPLEX WALL SWITCH AWST 8802 WIRELESS DUPLEX WALL SWITCH Picture of the AC 300 A Removable button D Battery not included B Removable switch E Mounting point plate F Or button C Off button AWST 8802 WIRELESS DUPLEX WALL SWITCH 1 Remove both buttons from the base 2 Install the battery with the pole face up A If necessary use a screwdriver to carefully pry A Ifthe battery must be replaced press the clip off the buttons A recess is provided on the release above the battery underside of the buttons for this purpose AWST 8802 WIRELESS DUPLEX WALL SWITCH 3 Snap the wall plate off of the base 4 Mount the switch transmitter at the desired location AWST 8802 WIRELESS DUPLEX WALL SWITCH 5 Activate the automatic search mode of the 6 Press one of the on buttons upper edge To receiver see the corresponding manual confirm the receiver switches on and off two times A This product only works with receivers with a product code that begins with A A The figure shows the AC 300 not includea AWST 8802 WIRELESS DUPLEX WALL SWITCH 7 Repeat 5 6 to assign the second button to 8 Place the wall plate and buttons back on the another receiver or if desired to the same base The product is ready for use receiver AWST 8802 WIRELESS DUPLEX WALL SWITCH co E Remarks A Reminders This2. attempt to repair this product If the product is damaged or if you are in doubt about the proper operation take the product back to the place of purchase Do not use the product in damp areas Clean the device with a clean cloth AWST 8802 WIRELESS DUPLEX WALL SWITCH co E A Power When some time has passed if a receiver no longer responds when the product is used replace the battery Only use a 3 Volt CR2032 lithium battery Do not throw the battery into an open fire Respect the local regulations when disposing of batteries A Wireless This product works using a radio signal that passes through walls windows and doors The range is maximum 75 metres in the open air The range indoors is strongly influenced by local conditions such as concrete glass and metals On average the indoor range is approximately 30 metres New double glass often includes a thin metallic layer This type of glazing HR glass allows most visible light to pass through but has a negative impact on radio signals If there is HR glass between the transmitter and receiver you should expect a significant reduction of the range of the wireless signal This product operates at a frequency of 433 92 MHz It complies with the essential requirements and other conditions of R amp TTE Directive 1999 5 EC and can be used in all EU countries There may be restrictions on the use of this device outside the EU If this device is used outside the EU check whether the
3. device complies with the local directives This product complies with the essential requirements and other relevant provisions of the applicable European directives The Declaration of Conformity DoC is available at www coco technology com Tf possible submit this product for recycling after use Do not dispose of the product with household trash Warranty and copyright This device is covered by a 2 year warranty that begins on the day of purchase Visit www coco technology com warranty for additional information Reprinting of portions of this manual without permission from Pan Trade International B V is expressly prohibited AWST 8802 WIRELESS DUPLEX WALL SWITCH co EP pit PAN TRADE INTERNATIONAL B V P O BOX 126 4760 AC ZEVENBERGEN THE NETHERLANDS www coco technology com Declaration of Conformity Pan Trade International BV declares that the COCO product model type designation AWST 8802 WIRELESS DUPLEX WALL SWITCH item number 74012 is in compliance with the essential requirements and other relevant provisions of directives R amp TTE 1999 5 EC EMC 2004 108 EC and LVD 2006 95 EC and is compatible with the standards EN 300 220 1 3 EN 55015 EN 301 489 1 3 and EN 60950 Manufacturer Authorised representative Afh M A Hoekstra managing director Zevenbergen 2008 01 30
4. product is a transmitter for operation of one COCO receiver independently or multiple receivers simultaneously This product must be used in combination with at least one COCO receiver not included The wireless system can be expanded indefinitely with other COCO remote controls and or receivers For all practical purposes the transmission code is unique 1 out of 67 million and is pre programmed at the factory You cannot change the house code This product can only be used with COCO receivers that automatically program themselves with the transmission code The type designation of these products always begins with an A This product can be used as a conventional wall switch but it can also be mounted on virtually any surface and at any location to control a COCO receiver To prevent interference avoid placing multiple products close to each other The minimum distance between units should be approx 50 cm If the product does not work Check the correct placement and or function of the battery replace if necessary Check step for step whether this product and the receiver are configured properly A Safety instructions Never use COCO products for life support systems or other applications in which equipment malfunctions can have life threatening consequences Do not expose this product to excessive heat direct sunlight or moisture Remove the battery from this product if it will not be used for an extended period Do not
Download Pdf Manuals
Related Search