GOS7513 Manual
Contents
1. ADJUSTMENT TO DIFFERENT TYPES OF GAS A N WARNING This operation must be performed by a qualified technician If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label on the top of the hob change the injectors Remove the information label and keep it with the instructions booklet Use pressure regulators suitable for the gas pressure indicated in the Instruction e The gas injectors must be changed by After Sales Service or a qualified technician e Injectors not supplied with the appliance must be ordered from After Sales Service e Adjust the minimum setting of the taps NOTE when liquid petroleum gas is used G30 G31 the minimum gas setting screw must be tightened as far as it will go IMPORTANT should you experience difficulty in turning the burners knobs please contact the After Sales Service for the replacement of the burner tap if found to be faulty IMPORTANT when gas cylinder is adopted the gas cylinder or gas container must be properly settled vertical orientation REPLACING THE INJECTORS see the injector table in the Instruction e Remove grids A e Extract burners B e Using a socket spanner of the appropriate size unscrew the injector C unscrew the injector to be replaced e Replace it with the injector suitable for the new type of gas Re assemble the injector in D B i e If you have a multipl2. Whirlodo BUILT IN GAS HOB SENSING THE DIFFERENCE IMPORTANT SAFETY INSTRUCTIONS YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY IMPORTANT This manual and the appliance itself provide important safety messages to be read and observed at all times All safety messages will follow the safety alert symbol and either the terms This is the safety alert symbol pertaining to safety which alerts users to potential hazards to themselves and others Indicates a hazardous situation which if not avoided will cause serious injury N DANGER Indicates a hazardous situation which if not avoided could cause serious injury All Safety messages will tell you what the potential hazard is tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed The appliance must be disconnected from the power supply before carrying out any installation work Installation and maintenance must be carried out by a qualified technician in compliance with the manufacturer s instructions and local safety regulations Do not repair or replace any part of the appliance unless specifically stated in the user manual If the information in this manual is not followed exactly a fire or explosion may result AN WARNING causing property damage or injury Donot store or use gasoline or other flammable vapors and liquids in the vicinity of this appliance What to do if you smell gas Do not try to l
3. children Before cleaning or maintenance wait for hob to cool down These instructions are valid only for the countries whose symbol is shown on the rating plate under cooktop This product is not intended to be installed and operated outdoor CAUTION In case of hotplate glass breakage shut immediately off all burners and any electrical heating element and isolate the appliance from the power supply do not touch the appliance surface donot use the appliance SAVE THESE INSTRUCTIONS INSTALLATION After unpacking the hob make sure that it has not been damaged during transport In the event of problems contact the dealer or your nearest After sales Service TECHNICAL INFORMATION FOR THE INSTALLER e Use protective gloves for handling preparing and installing the product e This product can be embedded in a worktop 20 to 60 mm thick e If there is no oven beneath the hob insert a separator panel that has a surface at least equal to the opening in the work surface This panel must be positioned at a maximum distance of 150 mm below the upper surface of the work surface but in no case less than 20 mm from the bottom of the hob In the case that you intend to install an oven beneath the hob make sure that it is manufactured by Whirlpool and equipped with a cooling system The manufacturer declines all liability if another brand oven is installed beneath the hob e Before installation make sure that the local gas del
4. d damaging the electric ignition device do not use it when the burners are not in their housing DECLARATION OF CONFORMITY C e This hob has been designed constructed and marketed in compliance with safety requirements of EEC Gas Directive 2009 142 EC ex EEC 90 396 safety objectives of the Low Voltage Directive 2006 95 CE which replaces 73 23 CEE and subsequent amendments protection requirements of EMC Directive 2004 108 EC SAFEGUARDING THE ENVIRONMENT Disposal of packing material The packing material is 100 recyclable and is marked with the recycle symbol lt 4 The various parts of the packing must therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal Scrapping the product This appliance is marked in compliance with European Directive 2002 96 EC Waste Electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol et on the product or on the accompanying documentation indicates that it should not be treated as domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic equipment PRODUCT DESCRIPTION 1 Removable panstand grids Auxiliary burner Sem
5. e crown burner use side spanner to replace ie the injector E Before installing the hob remember to affix the gas calibration plate supplied with the injectors in such a way that it covers the existing information relating to gas calibration ADJUSTING MINIMUM GAS SETTING OF TAPS To ensure that the minimum setting is correctly adjusted remove the knob and proceed as follows e tighten screw to reduce the flame height e loosen screw to increase the flame height The adjustment must be performed with the tap in minimum gas setting position small flame e The primary air of the burners does not need to be adjusted e Atthis stage light up the burners and turn the knobs from max position A to minimum position to check flame stability Upon completion of adjustment reseal using sealing wax or an equivalent material REFERENCE TO LOCAL REGULATIONS Ensure that the installation and gas connections are performed by a qualified technician following the manufacturer s instructions and in compliance with current local safety regulations AFTER SALES SERVICE Before calling the After Sales Service make sure you can give the following information type of fault or problem exact model written on the label affixed to the instruction warranty service number that follows the word SERVICE on the rating plate under the hob and on the label affixed to instruction warranty your complete address and phone numbe
6. er after installation Do not touch the appliance with any wet part of the body and do not operate it when barefoot This hob class 3 is designed solely for private household use for cooking food Do not use this appliance as a space heater to heat or warm the room Doing so may result in carbon monoxide poisoning and overheating of the hob The Manufacturer declines all responsibility for inappropriate use or incorrect setting of the controls The appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or with lack of experience and knowledge of the appliance unless supervised or previously instructed in its use by those responsible for their safety Young children should be kept away from the appliance and supervised to ensure that they do not play with it The use of a gas appliance produces heat and humidity in the room Make sure the room is well ventilated or install an extractor hood with exhaust duct Incase of prolonged use additional ventilation may be necessary by opening a window or increasing the hood extraction speed ee 277 TEN CEs CD GR CD After use make sure the knobs are in off position and close the main gas supply cock or the gas cylinder valve QOverheated oils and fats catch fire easily Always remain vigilant when cooking foods rich in fat oil or alcohol e g rum cognac wine Keep the packaging materials out of the reach of
7. ess steel surfaces may be stained by calcareous water or aggressive detergents if left in contact for too long Any food spills water sauce coffee etc should be wiped away before they dry e Clean with warm water and neutral detergent and then dry with a soft cloth or chamois Remove baked on dirt with specific cleaners for stainless steel surfaces NOTE clean stainless steel only with soft cloth or sponge e Do not use abrasive or corrosive products chlorine based cleaners or pan scourers e Donotuse steam cleaning appliances e Do not use flammable products e Do not leave acid or alkaline substances such as vinegar mustard salt sugar or lemon juice on the hob CLEANING THE HOB PARTS e Clean glass and enamelled parts only with soft cloth or sponge e Grids burner caps and burners can be removed to be cleaned e Clean them by hand with warm water and non abrasive detergent removing any food residues and checking that none of the burner openings is clogged e Rinse and dry e Refit burners and burner caps correctly in the respective housings e When replacing the grids make sure that the panstand area is aligned with the burner e Models equipped with electrical ignition plugs and safety device require thorough cleaning of the plug end in order to ensure correct operation Check these items frequently and if necessary clean them with a damp cloth Any baked on food should be removed with a toothpick or needle NOTE to avoi
8. h as metal mesh or any other types HAM g Two burners simultaneously for one receptacle e g fish kettle Rapid 214 g h Liquids spilled on hot hob area can cause glass damage a ena use g ge PETROLEUMGAS Semi rapid 125 g h HOW TO USE THE HOB Propane G31 Auxiliary 71 g h 3 Do not let the burner flame extend beyond the edge of the pan Model Rated thermal Total rated Air required m for AN WARNING configuration flow rate kW consumption burning 1 m of gas IMPORTANT WHEN THE HOB IS IN USE THE ENTIRE HOB AREA MAY BECOME HOT ATLASA alai e To ignite one of the burners turn the relative knob anti clockwise to the maximum flame setting 2R 2SR 1 AUX 763 g h e Press the knob against the control panel to ignite the burner e After the burner has ignited keep the knob pressed for about 5 10 seconds to allow proper device operation This burner safety device shuts off the gas supply to the burner if the flame goes out accidentally because of sudden ELECTRIC SUPPLY 220 240 V 50 60 Hz draught an interruption in the gas delivery boiling over of liquids etc e The knob must not be pressed for more than 15 sec If after that time has elapsed the burner does not remain lit wait at least one minute before trying to light it again NOTE should particular local conditions of the delivered gas make the ignition of burner difficult it is advisable to repeat the operation with the knob turned to small flame setting The burner migh
9. i rapid burner Semi rapid burner Rapid burner 2 3 4 Rapid burner 5 6 7 Semi rapid burner control knob a 8 Semi rapid burner control knob 9 Rapid burner control knob s 10 Auxiliary burner control knob 11 Rapid burner control knob s Symbols Tap closed A Maximum flame A Minimum flame PRACTICAL ADVICE FOR USING THE BURNERS INJECTORS TABLE CATEGORY II2H3 This hob has burners of different diameters For better burner performance Pot please stick to the following rules Type of gas Type of burner Injector Rated thermal Rated Reduced heat Gas pressure Use pots and pans with bottoms the same width as that of the burners or From 24 to 26 cm used marking flowrate consumption capacity slightly larger see table on the right From 16 to 22 cm KW Only use flat bottomed pots and pans Use the correct amount of water for cooking foods and keep the pot Rapid 286 l h covered Nee wise Semi rapid 167 l h Make sure pots on the grates do not protrude beyond the edge of the hob Methane G20 7 IMPORTANT improper use of the grids can result in damage to the hob do Auxiliary 95 Ih not position the grids upside down or slide them across the hob LIQUEFIED Rapid 218 g h Donotuse PETROLEUMGAS Semi rapid 127 g h Cast iron griddles ollar stones terracotta pots and pans Butane G30 Auxili 73 a h Heat diffusers suc
10. ight any appliance Do not touch any electrical switch Do not use any phone in your building Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or the gas supplier Use appliance in well ventilated rooms only The electrical and gas connections must comply with local regulations When the hob is installed provide a multi pole circuit breaker with a contact separation of at least 3 mm that provides full disconnection Regulations require that the appliance is grounded The power cable must be long enough for connecting the appliance once fitted in its housing to the power supply Use only flexible or rigid metal hose for gas connection If necessary the electrical power cable must be replaced exclusively with a power cable having identical characteristics to the original supplied by manufacturer type HO5V2V2 F 90 C or HO5RR F This operation must be performed by a qualified electrician The manufacturer cannot be held responsible for any injury to persons or animals or damage to property arising from failure to comply with these requirements Do not use multiple plug adapters or extension cords Donot pull the power supply cord in order to unplug the appliance The electrical components must not be accessible to the us
11. ivery conditions nature and pressure are compatible with the settings of the hob see the rating plate and injector table the outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations this appliance is not connected to a fume exhaust device It shall be installed in accordance with current installation regulations Particular attention shall be given to the relevant requirements regarding ventilation combustion products are discharged outdoors through specific hoods or wall and or window mounted electrical fans GAS CONNECTION AN WARNING This operation must be performed by a qualified technician e The gas supply system must comply with local regulations You can find specific local regulations for some countries in the paragraph Reference to Local Regulations If no information concerning your Country is given please ask details to your Installer The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or steel pipe with fittings complying with local regulations or by means of a continuous surface stainless steel hose complying with local regulations The maximum length of the hose is 2 linear metres Connect elbow A or B supplied with to the hob inlet main pipe and interpose the washer C supplied in compliance with EN 549 Use elbow A for France and elbow B for all other destinations IMPORTANT if a stainles
12. r If any repairs are required please contact an authorised After Sales Service as indicated in the warranty py eee mess 0000 000 00000 TROUBLESHOOTING GUIDE If the hob will not operate correctly before calling the After Sales Service refer to the Troubleshooting Guide to determine the problem 1 The burner fails to ignite or the flame is not even Check that e The gas or electrical supplies are not shut off and especially that the gas supply tap is open The gas cylinder liquid gas is not empty The burner openings are not clogged e The plug end is not dirty e All the burner parts have been positioned correctly e There are no draughts near the hob 2 The burner does not stay lit Check that When lighting the burner the knob has been pressed for enough time to activate the protection device e The burner openings are not clogged near the thermocouple e The end of the safety device is not dirty e The minimum gas setting is correct see relevant paragraph 3 The containers are not stable Check that The bottom of the container is perfectly flat e The container is centered on the burner The grids have not been exchanged or positioned incorrectly If after the above checks the fault still occurs get in touch with the nearest After Sales Service CLEANING THE HOB SURFACE WARNING Disconnect power before servicing All the enamelled and glass parts should be cleaned with warm water and neutral solution Stainl
13. s steel hose is used it must be installed so as not to touch any mobile part of the furniture It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length After connection to the gas supply check for leaks with soapy water Light up the burners and turn the knobs from max position A to minimum position f to check flame stability Manufacturer Whirlpool Europe S r l Viale G Borghi 27 21025 Comerio VA ITALY ELECTRICAL CONNECTION A N WARNING This operation must be performed by a qualified technician AN WARNING e The electrical connections must comply L with local regulations e The earthing of this appliance is compulsory by law e Do not use an extension cord Earth yellow green IMPORTANT the data relevant to the voltage and power absorption are indicated on the rating plate ASSEMBLY After having cleaned the perimeter surface apply the supplied gasket to the hob as shown in the figure Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction NOTE the power supply cable must be long enough to permit its upward extraction To secure the hob use the brackets A provided with it Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws in accordance with the thickness of the worktop see the following figures Top 40 mm i ZZ 40
14. t go out when the knob is released This means that the safety device has not warmed up enough In this case repeat the operations described above DIMENSIONS AND DISTANCES TO BE MANTAINED mm WOK ADAPTER not included this accessory can be purchased separately from the After sales Service NOTE if the distance A between the wall cabinets is between 600 mm and 730 mm the height B must be a minimum of 530 mm If the distance A between the wall cabinets is greater than the width of the cooktop the height B must be a minimum of 400 mm In case of installation of a hood above the cooktop please a Y aT RE Mi P i i refer to the hood instructions for the correct distance hari Hi Tae key il Hal i Re Ma af i i DE i 1 i sea H li ij il 4 li 1E i l Lae aija li
Download Pdf Manuals
Related Search