LEDSPOT 300 User Manual
Contents
1. 2 70 8 99 4 00 13 32 5 30 17 65 Signal Set Wire DMX Wireless DMX Act WDMX amp Out Program1 Scenes 01 Pan XXX Set each scenes one value and time Programs Scenes XX Time xx xS Mode of channel Standard Mode Basic Mode Extended Mode2. 11 Maintenance and Cleaning The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed CAUTION Disconnect from mains before starting maintenance operation In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakneness of the lights due to accumulation of dust 2 Clean the fan each week 3 Adetailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instructions
3. D shutter strobe effect with variable speed Preset variable random strobe and dimming pulse effect 17 15 17 DMX channels USITT DMX 512 Customizable DMX channel assignment 17CH DMX512 master slave and sound activated controllable or auto operation 8 built in programs DMX recorder and edit function integrated Blue background LCD display Powercon IN OUT 3 pin XLR connectors IN OUT Fan cooling system 2 Safety Instructions l CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch iton immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate voltage and frequency Make sure that t
4. N Open White White Color 1 FE Pin XLR Socket 3 Pin XLR Socket COMMON ee DMX512 OUT Ee DMX512 IN 024 031 031 Color 1 Colr2 1 Color 2 Data 1 3 PIN XLR Joe 3 PIN XLR Color 2 5 Color er For installations where the DMX cable has to run a long distance or is in an electrically noisy Mode 2 Color 3 environment such as in a discotheque it is recommended to use a DMX terminator This helps in Color 3 Color 4 preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an Color 4 XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then plugged into the output 072 079 Color 4 Color 5 XLR socket of the last fixture in the chain Please see illustrations below 080 087 Color 5 S 088 095 Color 5 Color 6 z PIN 3 PIN 2 6 Photometric Data 7 Menu Operations Ib Photometric Beam Angle Data 12 36 Beam Angle LUX x 0 0929 FC DMX Address A001 AXXX P 1875 201 4 2 223 2400 126 1350 36 418 4500 105 1130 48 510 28 300 FC LUX a fow owen fo owe fow mems o ooo Sensitivity of mic Calibration Code Code 088 PAN TILT Color Wheel Gobo 1 Wheel 1 Gobo Wheel 2 Focus l l l l l l l l l i ee Om 0ft 2 5m 8 2ft 5m 16 4ft 7 5m 24 6ft 10m 32 8ft Prism Beam Diameter 12 0 55 1 83 1 04 3 46 1 50 4 99 2 06 6 86 m ft XXX CF Beam Diameter 36 1 40 4 66
5. Should you need any spare parts please order genuine parts from your local dealer CE LEDSPOT 300 User Manual KEEP THIS MANUAL FOR FUTURE NEEDS 1 Unpacking Thank you for choosing the LEDSPOT 300 with linear motorized zoom from 12 to 36 For your own safety please read this manual before installing the device This manual covers the important information on installation and applications Please install and operate the fixture with following instructions Meanwhile please keep this manual well for future needs The LEDSPOT 300 is made of a new type of high temperature strength of engineering plastics and cast aluminum casing with nice outlook The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol It s available independently controlled and linkable with each other for operation And it is applicable for large scale live performances theater studio nightclubs and discos LEDSPOT 300 adopts powerful 300W pure white LED which features high brightness and stability Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation And please check whether the following items are included inside the box LEDSPOT 300 One Signal Cable One Omega Clamp Two Power Cable One Safety Chain One User Manual One Constant temperature readout and management function 45 C max
6. ambient temperature IP20 protection rating 55dB at 3 dB rating 2 1 4 turn fastening Omega clamps 10 Specifications Input Voltage AC90 260V 50 60Hz LED Quantities 1 300W High brightness white LED lamp Control Signal DMX512 master slave and sound activated or auto operation Control Channel 17 15 17 DMX Channels Power Consumption 390W Dimensions 318 D 411 W 628 H mm Packing Dimensions 480 D 610 W 460 H mm Net Weight 21kg Gross Weight 23 5kg 9 Key Features A 300W single white LED lamp 50000 hours life span and low power consumption 8 16 bit smooth and precise resolution for PAN TILT movement 540 630 PAN and 270 TILT movement Scan position memor y auto reposition after unexpected movement Linear motorized zoom with 12 to 36 beam angle Improved optics and flat beam field 1 rotatable gobo wheel with 7 rotatable and interchangeable glass gobos plus open with speed adjustable stream effect dithering effect and rotatable clockwise or anticlockwise Gobo indexing Gobo size 27 9mm external dimensions 23mm inner dimensions 1 static gobo wheel with 9 gobos plus open Gobo overlay gobo morphing 1 color wheel with 7 colors plus open Variable direction rainbow effect with speed adjustable 2 meter to infinite electric focus Motorized linear IRIS 3 facet prism with variable speed and direction Variable linear frost filter Hybrid effect for wash 0 100 linear LED dimmer 20T sec high speed LE
7. he available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more than 50cm distance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard 3 Operation Instructions ee The LEDSPOT 300 is for spot effect for on site decoration purpose 006 127 PON Don t turn on the fixture if it s been through severe temperature difference like after Re 128 189 transportation because it might damage the light due to the environment changes So make sure 190 193 to operate the fixture until it is in normal temperature 193 255 This light should be keep away from strong shaking during a
8. nt integrated in the base assembly Omega Bracket sSatety Clamp safety Cable 1 4 Turn Quick Lock Fasteners 1 4 Turn 1 4 Turn Regardless of the rigging option you choose for your LEDSPOT 300 always be sure to secure your fixture with a safety cable The fixture provides a built in rigging point for a safety cable on the hanging bracket as illustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle Gobo 1 Rot p om o 8 DMX Channels 5 DMX 512 control connections Mode Channel Description Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to EE on the male 3 pin XLR input of the moving head You can chain multiple 0 255 PAN Movement Moving head together through serial linking The cable needed should be two core screened cable with 0 255 Fine control of Pan movement XLR input and output connectors Please refer to the diagram below 0 255 Tie Movement DMX 512 connection with DMX terminator 0 255 Fine control of Tilt movement 0 015 Open White MH 016 031 Color 1 032 047 Color 2 t 048 063 Color 3 N 064 079 Color 4 Color NU gt 2 S 080 095 Color 5 Yt Mode 1 096 111 Color 6 112 127 Color 7 I ITO 128 189 Forwards rainbow effect from fast to slow 190 193 Color rotation stop POWER IN 194 255 Backwards rainbow effect from slow to fast DMX I
9. ny transportation or movement 0 191 0 191 Frost 0 100 Frost Don t pull up the light by only the head or it might cause damages to the mechanical parts Iris Don t expose the fixture in overheat moisture or environment with too much dust when installing it And don t lay any power cables on the floor Or it might cause electronic shock to the people Make sure the installation place is in good safety condition before installing the fixture 192 223 Pulse opening fast to slow 224 254 Pulse closing slow to fast Make sure the lens are in good condition It s recommended to replace the units if there are any vr damages or severe scratch Speed of 226 235 Blackout by movement Make sure the fixture is operated by qualified personnel who knows the fixture before using Pan Tilt 236 245 Blackout by all wheel changing Keep the original packages if any second shipment is needed Don t try to change the fixtures without any instruction by the manufacturer or the appointed Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture repairing agencies lt is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation like shock short circuit electronic shock lamp broke etc 200 219 Internal program 6 220 239 Internal program 7 240 255 Internal program 8 Gobo 2 Shutter pao fe oe mer 0255 oone ufo fa
10. r sos os momsen 4 Mounting and Installation Cautions For added protection mount the fixtures in areas outside walking paths seating areas or in areas were the fixture might be reached by unauthorized personnel Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture from a periodic safety inspection of all installation material and the fixture If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet Clamp Mounting The LEDSPOT 300 provides a unique mounting bracket assembly that integrates the bottom of the base the included Omega Bracket and the safety cable rigging point in one unit see the illustration below When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the omega bracket As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the safety cable rigging poi
Download Pdf Manuals
Related Search