fi8910e quick installation guide - Foscam.us
Contents
1. IF Address 132 166 0 102 Subnet Mask 255 255 255 132z 166 0 1 Modify the HTTP Port to a four digit number other than 80 Gateway DHS Server 132 166 6 1 Http Port User Enter the Username and Password and then click OK Fassword Changing the port in IP Camera Tool Enter the username and password of the Administrator default username is admin with a blank password and click OK to apply changes Wait around 10 seconds or wait for the camera to reboot you ll see that the camera s LAN IP address has changed In our example it was changed to 2000 so we see http 192 168 8 102 2000 in IP Camera Tool Also the LAN IP address is now fixed at a static IP address of http 192 168 8 102 2000 This IP address will not change even if the camera is powered off and back on the camera will remain on this LAN IP address This is very important that a static LAN IP address is set or you may have problems later with remote access and seeing the camera remotely if the camera loses power and reconnects on a different LAN IP address Make sure you set a static LAN IP address any IP Camera Jool Camera name IP Adress Device ID Device type Anonymous http 192 168 8 102 2000 00626E4DFD88 H Static IP address and port 2000 set in IP Camera Tool Setting up Remote Access First check to see if your ISP Internet Service Provider provides a Static WAN IP add2. Quick Installation Guide x 1 CD ROM with Setup Software x 1 Security Warning Card x 1 Quick Installation Diagram Hardware Installation dL Software Installation JL Login to the Camera JL Remote Access Setup igs Other Settings Foscam Digital Technologies LLC FI8910E Quick Installation Guide Security Warning Foscam cameras require good security practices to safeguard your privacy You can help protect your camera by changing the default username and or password You should update your camera regularly at http www foscam us firmware html Make sure your camera has the latest firmware installed for your specific camera model Power over Ethernet PoE The Network Camera is POE compliant allowing transmission of power and data via a single Ethernet cable Such as the following picture connect the Network Camera to a POE enabled router switch via Ethernet cable w es ie 16 Foscam Digital Technologies LLC FI8910E Quick Installation Guide Start Installation 1 Hardware Installation When using a PoE enabled routerlswitch 1 Open the package Take out the camera out of the box carefully 2 Get the camera connected to the router Figure1 1 Connect the Network Camera to a PoE enabled router switch via Ethernet cable at your home or your office The green network light at the rear of the camera will blink and the camera will automatically pan tilt The red power light wi
3. Settings Multi Device Settings Enable Basic Network Settings Manufacturer s Domain Wireless LAN Settings ADSL Settings UPnP Settings DDNS Service Settings DDNS Service Settings Manufacturer s DDNS Enable FOSCAM DDNS Camera myfoscam org Third Party DONS Mail Service Settings MSN Settings DDNS Service FIP Service Settings Alarm Service Settings DDNS Settings page Foscam Digital Technologies LLC FI8910E Quick Installation Guide So for example once port forwarding is set up correctly and you have a DDNS optional you can use the three following methods to access the camera remotely Foscam s DDNS http Domain HTTP Port For example hitp ad6016 myfoscam org 2000 Using Third Party DDNS No IP DynDNS For example http foscamusat1 no ip org 2000 Using External IP http IP Address HTTP Port For example http 12 69 124 226 2000 If you do not have a DDNS set up you can use the third method to log into your camera NOTE If you are still unable to access the camera remotely try checking to see if your port forwarding is working correctly by going to www canyouseeme org Input your port number and click check to see if the port is opened properly If you have done port forwarding correctly but the port is being blocked you may need to contact your ISP and request the port be unblocked for your usage If you want to use a Third Party Domain like DynDNS or No IP please read
4. 0 0 1 100 Private UDP Ports 2000 Private TCP Ports 2000 Cancel Save As you can see we are inputting the port forwarding information such as the port IP address and the name of the port forwarding rule Fill these fields in accordingly based on what information you would like to include in terms of the port you want to forward your local IP address of the camera and the custom name you would like to provide Oo 8 AirPort Utility The device and its network services will be temporarily unavailable Are you sure you want to wS continue _ Do not show this warning again Cancel Continue Enable Access Control Timed Access Control Cancel Update Once the port forwarding rule has been created you will see it in the list where the Port Settings section is This confirms that you have successfully added a port forwarding rule Next click Update You will be prompted if you would like to continue the router will most likely update its settings for a few seconds and come back online Once it comes back online your port forwarding settings will be confirmed Congratulations port forwarding should now be done 25 Foscam Digital Technologies LLC FI8910E Quick Installation Guide Using the embedded DDNS to access the camera via the Internet Some Foscam cameras have an embedded unique DDNS domain name the format of this domain name is xxxxxx myfoscam org
5. On the bottom of the camera you can see the domain name sticker with this information on it or it should appear on the DDNS Settings page in your camera Device Status Alias Settings Date amp Time Setting Users Setting Manufacturer s DDNS Muki Device Setting Eis Enable FOSCAM DDNS s ins neal Manufacturer s Domain camera m cano Wireless LAN Setting Validity Queries DDNS Service Settings ADSL Setting UPnP Setting DDNS Service Setting N Third Party DDNS Mail Service Setting MSN Settings DDNS Service None FTP Service Setting i gt Alarm Service Setting DDNS Settings page So for example once port forwarding is set up correctly and you have a DDNS optional you can use the three following methods to access the camera remotely Foscam s DDNS http Domain HTTP Port For example http ad6016 myfoscam org 2000 Using Third Party DDNS No IP DynDNS For example http foscamusa1 no ip org 2000 Using External IP http IP Address HTTP Port For example http 12 69 124 226 2000 If you do not have a DDNS set up you can use the third method to log into your camera NOTE If you are still unable to access the camera remotely try checking to see if your port forwarding is working correctly by going to www canyouseeme org Input your port number and click check to see if the port is opened properly If you have done port forwarding correctly but the port is being blocked you may need to conta
6. V50 01 OSCAM Model FI8910E Quick Installation Guide Indoor Pan Tilt PoE IP Camera FOSCA Black White For Windows OS Page 1 For MAC OS Page 14 Foscam Digital Technologies LLC FI8910E Quick Installation Guide Quick Installation Guide For Windows OS Package Contents P Camera x 1 DC Power Adapter 5V 2 0A x1 Network Cable x 1 Mounting Bracket x1 Quick Installation Guide x 1 CD ROM with Setup Software x 1 Security Warning Card x 1 Quick Installation Diagram Hardware Installation b Software Installation d L Login to the Camera JL Remote Access Setup d L Other Settings Foscam Digital Technologies LLC FI8910E Quick Installation Guide Security Warning Foscam cameras require good security practices to safeguard your privacy You can help protect your camera by changing the default username and or password You should update your camera regularly at http www foscam us firmware html Make sure your camera has the latest firmware installed for your specific camera model Power over Ethernet PoE The Network Camera is POE compliant allowing transmission of power and data via a single Ethernet cable Such as the following picture connect the Network Camera to a POE enabled router switch via Ethernet cable gt power data transmission BF i ERE inana yawanamanamamamanka fi i _ u ff Za PoE Switch Fi i i _ l
7. VM_IPCam2 ActiveX Control Module from ShenZhen Foscam Intelligent Technology Co Ltd Allow 7 x What s the risk In the above screenshot we see a grey screen for camera video and a red X in the top left corner This indicates that our ActiveX controls are not configured properly Usually in Internet Explorer versions 8 or later you will see a pop up box at the bottom of the screen sbs Foscam Digital Technologies LLC FI8910E Quick Installation Guide which asks if you would like to allow the ActiveX control module to run for the camera Click Allow Once you login again you should be able to see live camera video Add onrecord enable v 640 480 X gF Device Management If you are logging into the camera using a server push browser like Google Chrome or Mozilla Firefox you would click on the Server Push Mode button which is used for these browsers Default user name is admin with no password Foscam Digital Technologies LLC FI8910E Quick Installation Guide FOSCAM www foscam us ActiveX Mode Server Push Mode r m Mobile Phone In Chrome or Firefox you will need to push the second login button on the login page From there you will be prompted to enter the username and password for the camera Type in admin for the username and leave the password field blank Then push enter or click Log In Once logged in click the Live Video button on the left side of the
8. Virtual Server or NAT Using the Linksys brand router as an example we would log into the router and go to the Applications amp Gaming menu We would then click on the Single Port Forwarding sub menu Create a new column using the LAN IP address amp HTTP Port of the camera within the router as shown below and then push OK or Submit to save your settings Wireless N Home Router WAT420N Applications amp Gaming Setup Wireless Security Access Restrictions Apphcations amp Administration Status Gaming Single Port Forwarding D Port Range Forwarding l Fort Range Triggering l Single Port Forwarding Internal Port Protocol To IP Address Enabled External Port Application Name Fill the HTTP Port of the peee O camera in the columns of External Port and Internal Port Example 2000 ewes a w W Fill in this section with the LAN IP of the camera we would enter 100 for our example s m IL My H Port forwarding in a Linksys Router Using the embedded DDNS to access the camera via the Internet Some Foscam cameras have an embedded unique DDNS domain name the format of this domain name is xxxxxx myfoscam org On the bottom of the camera you can see the domain name sticker with this information on it or it should appear on the DDNS Settings page in your camera Device Status Alias Settings Date amp Time Settings Users
9. a name for the i 192 1688 Port Example 2000 port forward setting here ae pp l r tin TT Foscamcam J E T 2 T son v TE Ld L bem ises a wra E Fill in this section with the LAN IP of the camera we would enter 100 for our example Port forwarding in a Linksys Router O32 Foscam Digital Technologies LLC FI8910E Quick Installation Guide For Apple Routers Foscam s AirPort Express network Foscam s Wi Fi Network IP address 169 254 243 203 LAN IP address 10 0 1 1 serial number C86J6LE9DW2R version 7 0 2 Status Internet Connection Foscam s AirPort Exp No DNS Servers AirPort Express Ethernet Unplugged __ Base Station Internet Router Mode DHCP and NAT ak DHCP Range 10 0 1 2 to 10 0 1 200 DHCP Reservations Description IPAddress a Enable Access Control Network Options Cancel J Update Click on the Network tab at the top we will be editing the Port Settings section of the Network page which is where port forwarding is done Click the symbol which will add a port forwarding rule JA Foscam Digital Technologies LLC FI8910E Quick Installation Guide Firewall Entry Type IPv4 Port Mapping Description Foscam Cam 1 7 Public UDP Ports 2000 Public TCP Ports 12000 _ Private IP Address 1
10. ct your ISP and request the port be unblocked for your usage If you want to use a Third Party Domain like DynDNS or No IP please read the DDNS Service Settings section in the User Manual on how to set it up D Foscam Digital Technologies LLC FI8910E Quick Installation Guide 5 Other Settings Security At your first time logging in the camera please go to Users Settings panel and reset the username or password to prevent intruders connect your device The default username is admin with a blank password Device Status U Setti Alias Settings SETS meus Date amp Time Settings Users Settings User Password Group Wireless LAN Settings m UPnP Settings aaas Alarm Service Settings PT Settings Upgrade Device Firmware Congratulations You have finished the quick installation guide of the camera Please refer to the electronic user manual in the CD ROM for other settings such as Alarm Settings Email Settings User Settings and much more Foscam Digital Technologies LLC 1402 7 Memorial Dr 132 Houston TX 77079 Telephone 1 800 930 0949 Sales sales foscam us Support support foscam us CEC lt E 27
11. ing Applications More search tools Your public IP address 16 12 69 124 226 Learn more This is your public WAN IP address external IP address 4 2 Dynamic IP Addresses DDNS is a service that allows your IP Camera especially when assigned with a dynamic IP address to have a fixed host and domain name This means that even though your WAN IP address is constantly changing you will have a fixed hostname you can use to access your cameras at all times You can access the camera directly from the Internet using the hostname and port number Foscam offers many different DDNS providers the most popular being No IP and DynDNS You can sign up for the following DDNS providers at the below websites http www no ip com http dyn com dns dyndns pro free trial What is Port Forwarding If you have never done port forwarding before you can open and view the following link to understand the basic concept Port forwarding allows for outside connections to access a specific device on your network from anywhere in the world Every router automatically blocks any incoming connections for safety purposes Using port forwarding you are telling your router to allow a connection through a certain port you can think of it as a gateway into your router You set this port to a specific device in our case an IP Camera so it can be accessed from anywhere in the world 22 Foscam Digital Technologies LLC FI8910E Quick Installation Guide C
12. l software is installed double click the icon on the desktop and the following screen should appear any IP Camera Jool Camera name IP Adress Device ID Device type Anonymous http 192 168 1 100 88 00626E4DFD88 H IP Camera Tool for Windows The IP camera tool should find your camera s IP address automatically your IP address may be different after you plug in the network cable If not please make sure that DHCP is enabled on your router and that MAC address filtering firewalls and anti virus are disabled temporarily until the camera is set up Double click the IP address of the camera your default browser will open to the camera login page Language English Default user name is admin with no password Foscam Digital Technologies LLC FI8910E Quick Installation Guide FOSCAM www Tfoscam us Note Please note that there are three login methods for IE browser please choose Activex mode for Safari Firefox Google Chrome please choose Server Push mode for mobile phone please choose the third mode If it is your first time logging into the camera using Internet Explorer click the ActiveX Mode button This mode is used for Internet Explorer It will then prompt you to download the ActiveX plugin OosD disabled Add OSD onrecord disable Resolution 32024 50 HZ 20 fps Flip Mirror SI ow amp vy 2 Device Management This webpage wants to run the following add on D
13. lick this link to learn more about port forwarding http portforward com help portforwarding htm How do we configure Port Forwarding For this section we will be using an example For our Linksys example let s say the camera s IP address is http 192 168 8 100 2000 For our Apple Router example let s say the camera s IP address is http 10 0 1 100 2000 Login to the router and go to your router s port forwarding or port triggering menu Sometimes this is also under the name of Virtual Server or NAT Using an Airport Express router as an example we would open the Airport Utility program and then edit our Apple router s information as seen in the following screenshots First we will go over how to port forward within a Linksys router in case you do not have an Apple brand router For Linksys Create a new column using the LAN IP address amp HTTP Port of the camera within the router as shown below and then push OK or Submit to save your settings Wireless N Home Router WRT120N Applications amp Applications amp Administration Status Gaming Gaming Setup Wireless Security Access Restrictions s s s npm am a single Port Forwarding Port Range Forwarding l Fort Range Triggering l DMZ l Single Port Forwarding Application Name External Port Internal Port _ Fill the HTTP Port of the s2tee____ O None W camera in the columns of nsziess OF External Port and Internal Assign
14. ll also turn on When using a non PoE routerlswitch 1 Open the package Take out the camera out of the box carefully 2 Get the camera connected to the router and get it powered Figure1 2 Use the network cable to connect the camera to the router or the switch in the LAN network at your home or your office Plug in the power The green network light at the rear of the camera will blink and the camera will automatically pan tilt The red power light will also turn on Figure1 1 Plug the network cable Figure1 2 Plug the network cable and Power 2 Software Installation Insert the CD into the CD drive of your Mac and find the folder For MAC OS Copy the IP camera tool to your MAC and start the program f Foscam Digital Technologies LLC FI8910E Quick Installation Guide UP Combai las IPP IP Camera Tool Icon for Mac 3 Login to the Camera Double click the IP Camera Tool icon and the following screen should appear enn IP Camera Tool Camera name IP Adress Device ID Device type Anonymous http 192 168 1 100 88 00626E4DFD88 H IP Camera Tool for Mac The IP camera tool should find the camera s IP address automatically after you plug in the network cable If not please make sure that DHCP is enabled on your router and that MAC address filtering firewalls and anti virus are disabled temporarily until the camera is set up Double click the IP address of the camera Safari will prompt you for a
15. n fa Foscam Digital Technologies LLC FI8910E Quick Installation Guide Start Installation 1 Hardware Installation When using a PoE enabled routerlswitch 1 Open the package Take out the camera out of the box carefully 2 Get the camera connected to the router Figure1 1 Connect the Network Camera to a PoE enabled router switch via Ethernet cable at your home or your office The green network light at the rear of the camera will blink and the camera will automatically pan tilt The red power light will also turn on When using a non PoE routerlswitch 1 Open the package Take out the camera out of the box carefully 2 Get the camera connected to the router and get it powered Figure1 2 Use the network cable to connect the camera to the router or the switch in the LAN network at your home or your office Plug in the power The green network light at the rear of the camera will blink and the camera will automatically pan tilt The red power light will also turn on Figure1 1 Plug the network cable Figure1 2 Plug the network cable and Power 2 Software Installation Insert the CD into the CD drive of your computer and find the folder For Windows OS Copy the IP camera tool to your computer and start the program or double click on the setup file to install Foscam Digital Technologies LLC FI8910E Quick Installation Guide THU Smersa IP Camera Tool icon 3 Login to the Camera Once the IP camera too
16. onfiguration this brings up the network configuration box as shown ar IP Camera Tool anonymous Upgrade Firm Refresh Came Select which camera Flush Arp Buff you d like to change the About IP Camd port for and right click Click on Network Configuration 20 Foscam Digital Technologies LLC FI8910E Quick Installation Guide anonymous Network Configuration Obtain IP from DHCP server H anonym IP Address 192 168 8 100 Subnet Mask 255 255 255 0 Gateway 192 168 8 1 DNS Server 192 168 8 1 Http Port 2000 Modify the HTTP port User Enter the Username and Password password click OK Cancel Changing the port in IP Camera Tool Enter the username and password of the Administrator default username is admin with a blank password and click OK to apply changes Wait around 10 seconds or wait for the camera to reboot you ll see that the camera s LAN IP address has changed In our example it was changed to 2000 so we see http 192 168 8 100 2000 in IP Camera Tool Also the LAN IP address is now fixed at a static IP address of http 192 168 8 100 2000 This IP address will not change even if the camera is powered off and back on the camera will remain on this LAN IP address This is very important that a static LAN IP address is set or you may have problems later with remote access and seeing the camera remotely if the camera lo
17. page and it will take you to the live video feed for the camera ol gS D c Q _ w e Flip L Mirror Resolution 640 400 Mode onz x Brightness _ 6 _ Wy Contrast ae 4 Wty Preset Set Alel Ga Refresh camera params Refresh video Snapshot Audio Close Audio a Device Management Congratulations You have succeeded in accessing the camera by a wired connection Be sure to leave all other menu options alone until finishing the rest of the installation fy ae Foscam Digital Technologies LLC FI8910E Quick Installation Guide 4 Remote Access Setup We have been able to access the camera within the LAN network and have set up a wireless connection but how do we access the camera via WAN or from outside networks through the internet to view from anywhere in the world or on our smart phones We have to set up Remote Access via Port Forwarding before we can access the camera outside of our own local area network What is the HTTP Port The HTTP Port is used to access the camera remotely All cameras have the default HTTP port of 80 For example if the LAN IP address of the camera is http 192 168 8 102 this means that the camera s HTTP port is 80 Since port 80 is set by default if you input the IP address at http 192 168 8 102 80 with a colon and 80 at the end it will default back to hitp 192 168 8 102 This is because it is understood that any time you are entering an IP add
18. r own local area network What is the HTTP Port The HTTP Port is used to access the camera remotely All cameras have the default HTTP port of 80 For example if the LAN IP address of the camera is http 192 168 8 102 this means that the camera s HTTP port is 80 Since port 80 is set by default if you input the IP address at http 192 168 8 102 80 with a colon and 80 at the end it will default back to hitp 192 168 8 102 This is because it is understood that any time you are entering an IP address without a colon and port number at the end it is defaulting to port 80 no matter what so the colon and port 80 are taken out of the end of the link because of this It is recommended to change port 80 to a different port usually in the 4 digit range The reason for this is because some other devices such as your router also share port 80 If this is the case you may experience slow speeds on the camera or you may not even be able to connect at all It is best to assign a specific port to your camera so that only your camera is using that specified port number We usually suggest changing your port to 8080 8090 or any type of 4 digit number just as long as it is not at port 80 You can set the port anywhere between 1000 and 20000 How do you assign a new HTTP port and a Static Local IP Address Open the IP Camera Tool and select the camera you would like to change the port for Right click on the IP address and click on Network C
19. ress service or a Dynamic WAN IP address service This guide has been divided into two different sections of setting up remote access one for Static IP addresses and one for Dynamic IP addresses If your ISP provides a Static WAN IP Address continue reading below If your ISP provides Dynamic WAN IP Address please go to Chapter 5 2 directly 4 1 Static IP Addresses Users who have static IP addresses do not need to set DDNS service settings for remote access When you have finished connecting the camera using the LAN IP address and port forwarding you can access the camera directly from the Internet using the WAN IP address and port number 9 Foscam Digital Technologies LLC FI8910E Quick Installation Guide How to Obtain the WAN IP address from a public website To obtain your WAN IP address you can go to Google at www google com and search What is my IP address It will offer you your public IP address which is your WAN External IP address You can also use http www whatismyip com if needed what Is my Ip address Web Images Maps shopping Applications Mare search tools Your public IP address I amp 12 69 124 226 Learn more This is your public WAN IP address external IP address 4 2 Dynamic IP Addresses DDNS is a service that allows your IP Camera especially when assigned with a dynamic IP address to have a fixed host and domain name This means that even though your WAN IP address is constantly changing
20. ress without a colon and port number at the end it is defaulting to port 80 no matter what so the colon and port 80 are taken out of the end of the link because of this It is recommended to change port 80 to a different port usually in the 4 digit range The reason for this is because some other devices such as your router also share port 80 If this is the case you may experience slow speeds on the camera or you may not even be able to connect at all It is best to assign a specific port to your camera so that only your camera is using that specified port number We usually suggest changing your port to 8080 8090 or any type of 4 digit number just as long as it is not at port 80 You can set the port anywhere between 1000 and 20000 How do you assign a new HTTP port and a Static Local IP Address Open the IP Camera Tool and select the camera you would like to change the port for Right click on the IP address and click on Network Configuration this brings up the network configuration box as shown me IP Camera Tool ok anonyRous Http 7 192 168 8 10 Basic Properties Hetwork Configuration Select which camera you d like to change the port for and right click Upgrade Firmware Refresh i Flush About IF Click on Network Configuration Foscam Digital Technologies LLC FI8910E Quick Installation Guide AS IP Camera Tool BAA IPCAN Network Configuration x IFCAN
21. ses power and reconnects on a different LAN IP address Make sure you set a static LAN IP address O IP Camera Tool Camera name IP Adress Device ID Device type Anonymous http 192 166 8 100 2000 O0626E4DFD66 H Static IP address and port 2000 set in IP Camera Tool Setting up Remote Access First check to see if your ISP Internet Service Provider provides a Static WAN IP address service or a Dynamic WAN IP address service This guide has been divided into two different sections of setting up remote access one for Static IP addresses and one for Dynamic IP addresses If your ISP provides a Static WAN IP Address continue reading below If your ISP provides Dynamic WAN IP Address please go to Chapter 5 2 directly 21 Foscam Digital Technologies LLC FI8910E Quick Installation Guide 4 1 Static IP Addresses Users who have static IP addresses do not need to set DDNS service settings for remote access When you have finished connecting the camera using the LAN IP address and port forwarding you can access the camera directly from the Internet using the WAN IP address and port number How to Obtain the WAN IP address from a public website To obtain your WAN IP address you can go to Google at www google com and search What is my IP address It will offer you your public IP address which is your WAN External IP address You can also use http www whatismyip com if needed what Is my Ip address Maps Shopp
22. the DDNS Service Settings section in the User Manual on how to set it up 5 Other Settings Security At your first time logging in the camera please go to Users Settings panel and reset the username or password to prevent intruders connect your device The default username is admin with a blank password Device Status Users Settings Alias Settings Date amp Time Settings Users Settings User Password Group e a O E ADSL Settings UPnP Settings _ Alarm Service Settings PT Settings Upgrade Device Firmware 12 Foscam Digital Technologies LLC FI8910E Quick Installation Guide Congratulations You have finished the quick installation guide of the camera for PC Please refer to the electronic user manual in the CD ROM for other settings such as Alarm Settings Email Settings User Settings and much more Foscam Digital Technologies LLC 1402 7 Memorial Dr 132 Houston TX 77079 Telephone 1 800 930 0949 Sales sales foscam us Support support foscam us 13 Foscam Digital Technologies LLC FI8910E Quick Installation Guide OSCAM Model FI8910E Quick Installation Guide For Mac OS Indoor Pan Tilt PoE IP Camera FOSEN Black White Foscam Digital Technologies LLC FI8910E Quick Installation Guide Quick Installation Guide For MAC OS Package Contents IP Camera x 1 DC Power Adapter 5V 2 0A x 1 Network Cable x 1 Mounting Bracket x1
23. username and a password Enter the username admin and leave the password field blank This is the default login information You will then see the camera s login page Language English Default Username is admin with no password 18 Foscam Digital Technologies LLC FI8910E Quick Installation Guide FOSCAM www foscam us ActiveX Mode Server Push Mode a Mobile Phone The Login Screen Since ActiveX mode is not compatible on Mac you will always click the Server Push Mode option to access the camera whether you are on Safari Chrome or Firefox Once you click on Server Push Mode you should be taken to the live video screen immediately AO TAI IMGOOr el UL LL a ele yoy YY p ag a alco ow Ney ee E Flip Cl Mirror Resolution 6404800 Mode 50Hz e Brightness 2 5 4 Contrast a why Preset Set pe Go Refresh camera params Refresh video Snapshot Audio Close Audio gF Device Management The Live Video Page 19 Foscam Digital Technologies LLC FI8910E Quick Installation Guide 4 Remote Access Setup We have been able to access the camera within the LAN network and have set up a wireless connection but how do we access the camera via WAN or from outside networks through the internet to view from anywhere in the world or on our smart phones We have to set up Remote Access via Port Forwarding before we can access the camera outside of ou
24. you will have a fixed host name you can use to access your cameras at all times You can access the camera directly from the Internet using the host name and port number Foscam offers many different DDNS providers the most popular being No IP and DynDNS You can sign up for the following DDNS providers at the below websites http www no ip com http dyn com dns dyndns pro free trial What is Port Forwarding If you have never done port forwarding before you can open and view the following link to understand the basic concept Port forwarding allows for outside connections to access a specific device on your network from anywhere in the world Every router automatically blocks any incoming connections for safety purposes Using port forwarding you are telling your router to allow a connection through a certain port you can think of it as a gateway into your router You set this port to a specific device in our case an IP Camera so it can be accessed from anywhere in the world Click this link to learn more about port forwarding http portforward com help portforwarding htm How do we configure Port Forwarding For this section we will be using an example Let s say the camera s LAN IP address is http 192 168 8 100 2000 Login to the router and go to your router s port forwarding or port triggering menu Sometimes this is 10 Foscam Digital Technologies LLC FI8910E Quick Installation Guide also under the name of
Download Pdf Manuals
Related Search