user MANuAL
Contents
1. Dip Switch Chart MicroSD Card Slot Battery mounting plate 1 4 20 Threaded socket Power switch Composite video output HDMI input Power Switch Composite video input Audio input Dip switches Antenna terminal POWERING ON amp OFF There are two ways to power the SkyVision AC or a Sony L series battery AC POWER To run the SkyVision via AC power use the included 12 V DC adapter to connect the SkyVision s DC power input to your AC power source To turn on the SkyVision press the power switch to the On position The SkyVision will turn on and enter standby mode and the power indicator LED will glow red Press the Power button to enter ready mode The power indicator LED will turn green and then glow red CAMERA BATTERY The SkyVision s built in battery plate accommodates Sony L series batteries This allows you to power the monitor with readily available batteries that you may already own For more information on compatible battery types refer to Specifications on page 28 To install a compatible battery slide the battery forward until it locks into place To turn on the SkyVision press he power switch to the On position The SkyVision will urn on and enter standby mode and the power indicator LED will glow red Press the Power button to enter ready mode The power indicator LED will turn green and then glow red USING THE WCM758 DVR MOUNTING THE SKYVISION Us2. cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation PRECAUTIONS Please read and follow these instructions and keep this manual in a safe place Exposure to high sound levels can cause permanent hearing loss Avoid istening at high volumes for extended periods of time eep this product away from water and any flammable gases or liquids Make sure this product is powered off when plugging it into a power source Use only the correct recommended voltage Do not attempt to disassemble or repair this product Do not place or store the SkyVision acedown since this can damage the screen Handle this product with care Avoid any unnecessary impacts to this product Do not block the vents in this product Disconnect this product from its power source before storage and during electrical storms Do not use chemical solutions to clean this product Clean it with only a soft dry cloth Keep this product away from children Make sure that this product is intact and that there are no missing parts To avoid damage to this product be careful not to overtighten or improperly thread any of the threaded fittings All photos are for illustrative purposes only TABLE OF CONTENTS ProdUcekContents errsn ee eee rene eed 6 OVERVIEW nino i 7 8 Powering ON and Off risen
3. from state to state o obtain warranty coverage contact the Elvid Customer Service Department to obtain a return merchandise authorization RMA number and return the defective product to Elvid along with the RMA number and proof of purchase Shipment of the defective product is at the purchaser s own risk and expense For more information or to arrange service visit www elvidcinema com or call Customer Service at 212 594 2353 Product warranty is provided by the Gradus Group www gradusgroup com Elvid is a registered trademark of the Gradus Group 2014 Gradus Group LLC AII Rights Reserved G com sana A Gradus Group Brand www elvidcinema com Gai
4. function separately from the Video buttons Up and Down Buttons Use these buttons to navigate the menu and the prompts Menu Button Use this button to the Video or Playback menu switch from the Video or Playback menu to the Setup menu or close out the menu from the Setup menu or a submenu Mode Button Use this button to alternate between recording and playback modes Rec OK Button Press this button to make a selection VIDEO MENU To access the Video menu press the Menu button when the DVR is in recording mode Resolution Select the video resolution You can choose D1 720 x 576 VGA 640 x 480 or QVGA 320 x 240 Higher resolution will produce a sharper image however the file size will increase as the resolution increases The default mode is D1 As you increase resolution you will increase the image quality as well as the file size You can choose D1 720 x 576 VGA 640 x 480 or QVGA 320 x 240 Loop Recording Loop recording will maintain a 3 5 or 10 minute file When video recording reaches the end of the designated time limit it will return or loop back to the beginning of the file and continue recording to overwrite the previously recorded data This mode is ideal for surveillance applications Motion Detection This mode will cause the DVR to automatically start recording when a moving object is detected Date Stamp This setting superimposes or burns a date stamp on the video an
5. il mo Ww Col mo nitor When this mode appear onscreen You no In mono a graysca or Temp When using 6500 K You can also con whi mode is usefu is enabled on can select red e image will a he SkyVision for calibrating the y the selected color green blue or ppear onscreen as a wired HDMI nitor you can select from the presets 9300 7500 and figure your own custom setting ch is labeled User in the Color Temp menu Customizing the color temperature is recommended only for advanced users OSD MENU Language You can set the onscreen language to English default Simplified Chinese French Italian German Spanish Japanese Korean Russian and Portuguese H Position Adjust the horizontal position of the onscreen menu V Position Adjust the vertical position of the onscreen menu OSD Timeout Use this setting to set the length of time the onscreen menu is d isplayed You can choose from 5 to 60 seconds in 5 second intervals or you can disable the feature so the menu remain out The default se s onscreen until you manually close it ing is 10 seconds Transparent Set the menu s level of opacity You can adjust this setting from 1 to 7 with 7 being the most transparent The default setting is off which makes the menu opaque FUNCTION MENU Reset Restore the SkyVision s menu to the factory default settings System Select the transmiss
6. HADE The sunshade prevents glare on the monitor s screen by blocking out stray light and is useful when shooting outdoors 1 Insert the sunshade s pegs into the monitor s sunshade slots 2 Slide the sunshade down until it locks into place To deploy the sunshade fully open its lid and wings THE MENU Before using the SkyVision make sure the monitor s settings are properly configured All of the setting configurations are located in the main menu which has four submenus Color Onscreen Display OSD Function and Sound The submenus are located in the left column of the main menu window Note The menu is accessible only when the SkyVision is receiving a video signal The Video menu has its own set of buttons that function separately from the DVR buttons Source Exit Button When the menu is open use the Source Exit button to exit the current menu submenu or menu item Menu Button Press the Menu button to access the menu or make a selection within the menu Minus and Plus Buttons When the menu is open use the Minus and Plus buttons to navigate the menu or adjust the value of a menu item When the menu is closed out you can use these buttons to adjust the monitoring volume of the SkyVision COLOR MENU In he Color menu you can adjust brightness contrast hue and saturation of the monitor from O dimmest to 100 bri ghtest for example Check Field Check Field mo
7. Make sure Check Field mode is turned off The images are not synchronized The onscreen image size is incorrect The SkyVision is emitting a high pitched whine feedback There is no sound NTSC and PAL settings may not be correctly set Make sure the monitor s display format matches that of the input Refer to System under the Function Menu section on page 19 for further reference The RF signal is too weak Make sure that Camera mode is disabled Check whether the aspect ratio is set correctly Make sure that the correct input signal is selected If you are using the SkyVision as a wired monitor check your cables to make sure they are properly connected and that they are reliable e Turn the monitor s volume all the way down or plug headphones into the headphone jack Increase the monitoring volume If you are using the SkyVision as a wired standard definition video monitor make sure your composite audio cable is fully plugged into the composite audio input DIP SWITCH 5880 5785 5752 5847 5645 5740 5840 5860 5805 5733 5828 5665 5945 5820 5825 5725 5809 5685 5925 5800 5845 5745 5790 5705 5905 5780 CHART 5865 5765 5771 5866 5885 5760 FCC STATEMENT This device complies with Part 15 of the FCC Rules Operation is subj
8. SKYVISION WCM 758DVR WIRELESS 7 DVR MONITOR USER MANUAL elvid INTRODUCTION hank you for choosing Elvid he Elvid WCM 758DVR SkyVision is a monitor designed to wirelessly receive video and audio from your 5 8 GHz composite video transmitter Equipped with an integrated DVR this monitor can record incoming content to a microSD card The DVR incorporates practical functions such as loop recording for maintaining a specific file length and motion detection to initiate recording when a moving object is detected he 7 LED panel s native resolution is 1024 x 600 with an aspect ratio of 16 9 native that you can set to 4 3 The onscreen menu makes it easy to fine tune your image offering adjustments or brightness contrast hue and saturation Broadcast specific eatures include safety frame markers and multiple display ormats The SkyVision can also be used for wired monitoring via its HDMI and composite video inputs as well as composite video oop through via its video output he SkyVision incorporates advanced tools like Check Field to calibrate the monitor a Focus setting to fine tune your focus and Camera mode to scale the incoming video signal when shooting on a DSLR There s also an integrated speaker and a 3 5 mm stereo headphone output for live audio monitoring FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not
9. d is useful for security or legal applications because it cannot be alte ed after recordi ng Recording Audio Choose to record audio along with video Image Quality The higher the image quality the shar per and more detailed the image but the larger the file size You can choose Super Fine Fine and Normal Motion Detection Sensitivity Adjust t he sensitivity o the motion detection setting You can choose high medium or low SETUP MENU Format This formats the microSD card inserted in the SkyVision and will erase all data on the card To optimize the file system it is recommended to format the microSD card in he monitor before use Date Time Set the SkyVision s internal clock Use the Up and Down buttons to make adjustments and the Rec OK button o advance to the next field Language Set the onscreen language You can choose English default German French Spanish Italian Portuguese raditional Chinese simplified Chinese or Japanese TV Mode Set the display format of the monitor You can choose NTSC or PAL Note If the image is not synchronized or you are unable to access the DVR menu after you the TV output format this is likely because the DVR output format is not synchronized with the monitor format If this occurs set the format via the monitor menu not the DVR menu For more information refer to System under Function Menu on page 19 Default Setting Restore t
10. e 12 V DC adapter is fully plugged in and that your AC power source is reliable Try switching AC power sources Make sure the SkyVision is not in standby mode See Powering On and Off on page 9 for further reference Make sure your transmitter is working properly Make sure the SkyVision and your 5 8 GHz composite video transmitter are set to the same channel See the DIP Switch Chart on page 33 for further reference If you replace the included antenna you may experience a degraded signal or even no signal at all Make sure the antenna matches the transmitter The SkyVision is f you are using the SkyVision turned on but there is as a wired monitor make sure no onscreen image or he HDMI or composite video the image is weak cable is securely plugged into he proper input connection on the SkyVision and that the input mode is set correctly Try pressing the Mode button to set he input mode Make sure the monitor is set to he proper input mode f you are powering the SkyVision with a battery make sure the battery is fully charged and properly seated in the battery plate f you are powering the SkyVision via AC power use only the supplied 12 V DC adapter f you are using the SkyVision as a wired monitor check your cables to make sure they are reliable The screen displays Check the brightness contrast only a black and white hue and saturation settings and image adjust as necessary
11. e the SkyVision s 1 4 20 threaded socket to attach the monitor to your mounting system Make sure your bracket can support the monitor SETTING THE SIGNAL Before setting the signal screw the antenna into the antenna erminal Use the DIP switches on the SkyVision to set the proper channel Make sure the SkyVision and your 5 8 GHz composite video transmitter are set to the same channel Refer to the DIP Switch Chart on page 33 for further eference For your convenience there is an included DIP Switch Chart quick reference card Press the Mode button to cycle through the input modes until RF appears on the monitor If your 5 8 GHz composite video transmitter is using the same frequency as the monitor the image will appear onscreen and the power indicator LED will glow green WIRED INPUT amp LOOP THORUGH HDMI INPUT The SkyVision is equipped with HDMI input for use as a wired high definition video monitor Use the included HDMI cable to connect your HDMI video source to the SkyVision s HDMI input and then press the Mode button to cycle through the input modes until HDMI appears on the monitor If your HDMI video source is sending a signal to the monitor the image will appear onscreen and the power indicator LED will glow green COMPOSITE VIDEO INPUT The SkyVision also has a composite video input for use as a wired standard definition video monitor Use the included composite video input cable to connect your com
12. ect to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FE ONE YEAR LIMITED WARRANTY his Elvid product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one 1 year from the original purchase date or thirty 30 days after replacement whichever occurs later The warranty provider s responsibility with respect to this limited warranty shall be imited solely to repair or replacement at the provider s discretion of any product that fails during normal use of this product in its intended manner and in its intended environment Inoperability of the product or part s shall be determined by the warranty provider If the product has been discontinued the warranty provider reserves the right to replace it with a model of equivalent quality and function his warranty does not cover damage or defect caused by misuse neglect accident alteration abuse improper installation or maintenance EXCEPT AS PROVIDED HEREIN THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY MPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO ANY MPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE This warranty provides you with specific legal rights and you may also have additional rights that vary
13. he SkyVision to the factory default settings This will erase all current settings and replace them with the default settings PLAYBACK MENU To access the Playback menu press the Mode button to switch to playback mode and then press the Menu button Delete Delete either a single file or all the files on the inserted microSD card Protect This function protects a file from accidental deletion You can lock or unlock the current file or all files on the inserted microSD card RECORDING amp PLAYBACK To start recording wi h the DVR follow these steps Before recording make sure all monitor and DVR settings are properly configured 1 In DVR recording mode insert a microSD card into the card slot When the DVR recognizes the card it will display To SD onscreen and bottom right corner of the screen 2 Set the SkyVision amemory card icon will appear in the o RF mode and make sure it s receiving a signal from your wireless video source For more information refer o Setting the Signal on page XX 3 Press the Rec OK button to start recording video The status LED will bli nk red during recording To stop recording press the Rec OK button To play back video from the DVR follow these steps 1 Switch the SkyVision to DVR playback mode 2 Use the Up and Down buttons to cycle through the video and photo files on the inserted microSD card Videos are indicated by a film ico
14. ion display format You can choose NTSC M default PAL M NTSC BG PAL N NTSC DK PAL DK PAL or SECAM BG Display Ratio You can set the aspect ratio for the onscreen image The options are 16 9 and 4 3 The default setting is 16 9 which is the SkyVision s native aspect ratio The 4 3 setting will scale the image to fit that aspect ratio Screen Markers You can set the SkyVision to display an onscreen box as a safety frame marker at a set percentage of he screen size You can set this to 80 85 90 93 96 or off The screen marker will not display at the same time as he menu Centre Markers This setting displays a marker in the center of the screen The center marker will not display at the same ime as the menu Camera Camera mode scales the incoming video signal to fill he screen This is useful when shooting on a DSLR You can urn this mode on or off SOUND MENU Volume Adjust the monitoring volume of the SkyVision from O to 100 Focus Use this setting to check the areas of the image that are in focus Activating this setting increases the sharpness and contrast of the monitor and exaggerates in focus areas USING THE DVR The DVR can record your incoming wireless video to a microSD card Before getting started make sure the DVR settings are properly configured The settings are located in the three DVR menus Video Setup and Playback The DVR system has its own set of buttons that
15. n in the top right corner of the screen and photos are indicated by a camera icon 3 To play or pause a video file press Rec OK To fast forward or rewind press the Down or Up buttons You can increase playback speed in either direction up to 2x 4x or 8x by pressing Down or Up a second third or fourth time To resume normal playback press Rec OK elvid SPECIFICATIONS Panel Size Panel Type Backlight Resolution Brightness Contrast ratio Viewing angle Dot pitch W x H Display ratio Input Output 7 TFT LED 1024 x 600 250 cd m 700 1 URT U D 70 75 0 05 x 0 15 16 9 RF HDMI composite video mono audio Composite video headphone 3 5 mm stereo mono speaker Supported formats 50 60 Hz Threaded socket nput voltage Power consumption Battery type RF receiving frequency RF wireless receiving sensitivity Frequency stability Dimensions L x W x H Weight 480i 480p 576i 576p 720p 1080i 1080p 1 4 20 6 to 24 V DC lt 8 W Sony L series 5 8 GHz broadband FM A V synchronization 32 channels 90 dBm typical value 100 ppm 7A x 5 3 x 2 0 18 9 x 13 4 x 5 cm 1 Ib 0 5 kg The SkyVision will not turn on The SkyVision is in RF mode but no wireless signal is detected If you are powering the SkyVision with a battery make sure the battery is fully charged and properly seated in the battery plate Make sure that th
16. posite video source to the SkyVision s composite video and audio inputs and then press the Mode button to cycle through the input modes until video appears on the monitor If your composite video source is sending a signal to the monitor the image will appear onscreen and the power indicator LED will glow green Note Your composite audio cable must be plugged into the SkyVision s composite audio input in order to monitor the sound Loop Through The SkyVision offers composite video loop through also known as pass through To loop the video signal through the monitor make sure the SkyVision is receiving a video signal from your composite video source and then connect a compatible composite video output cable to the output connection on the monitor You can monitor sound via the integrated speaker or the 3 5 mm stereo headphone jack To monitor via the headphone jack plug in a pair of compatible headphones For more information on volume control refer to Volume under the Sound Menu section on page 20 and Right Button under the Using the DVR section on page 21 MONITORING SOUND You can monitor sound via the integrated speaker or the 3 5 mm stereo headphone jack To monitor via the headphone jack plug in a pair of compatible headphones For more information on volume control refer to Volume under the Sound Menu section on page 20 and Right Button under the Using the DVR section on page 21 THE SUNS
17. s 9 10 Using the WCM 758DVR iiiiii 11 Wired Input And Loop Throughi 12 13 onitoring Sound di The SUNSHACE ou eeseessecsesssestesseeseessestestecseesscsteateesecseeseesseatees The Meni recsa dii aaa Color Menu sas aaa 7 OSOM EMU ee ee ese ene tegen 18 Fonction Men iano eitatbececetese 9 Sauna MENU iena 20 Using Video Setup Playback Menu 25 Recording and Playback w ccccesccsssesseseseesecsteseeeeseens 26 27 SPECIMCAtionst s pprrenso i caceecceczecesletecdectscecaesinles 28 29 Troubleshootinp rrra sai 30 32 Dip switchichart nie lana 33 FCC Statement e Warrame ea RES 35 PRODUCT CONTENTS 7 Wireless DVR Monitor Antenna Sunshade Mini HDMI to HDMI cable 12 V DC adapter Dip Switch Quick Reference Card User manual NOTE Additional battery plates and or battery adapters compatible with other popular brands can be purchased by visiting www elvidcinema com OVERVIEW GG id j sourceeor menu QO elvid Headphone jack Rec OK button Status LED Mode button Screen Source Exit button Menu button Minus DVR Menu Button Up Down Plus Speaker
Download Pdf Manuals
Related Search