100Base-FX Multi-mode to 100Base
Contents
1. 19 Application Diagram 1 19 Application Diagram 11 20 Application Diagram 111 20 100Base FX Multi mode to Single Mode Converter 1 Introduction About This Guide Welcome Thank you for choosing the 100Base FX Multi mode to Single Mode Media Converter This device integrates Fast Ethernet multi mode and single mode fiber segments in a highly flexible package Purpose This guide discusses how to install and configure your 100Base FX Multi mode to Single Mode Media Converter Terms Usage In this guide the term Converter first letter upper case refers to your 100Base FX Multi mode to Single Mode Media Converter and converter first letter lower case refers to other converters 100Base FX Multi mode to Single Mode Converter Features e Complies with IEEE 802u standard e Supports Multi mode ST or SC Single Mode SC Connectors e Fiber 850nm 1310nm 1550nm fiber where applicable e Extend fiber distance up to 60km per segment max possible distance of 120km with converter situated in middle of two segments e Auto detection of half full duplex mode e Compatible with other Fast Ethernet Multi mode to Single Mode devices e Status LEDs for Power Receive amp Link to easily monitor network activity e Suitable as stand alone or in 19 4 12 slot rack mount converter chas2. 400 Bose TX to FX Corwerter 400 Bose TXto FX Converter 100 m 2km 20km AU EI t c A T 79 c a 100825 FX MM to Coruerter 100Base FX Multi mode to Single Mode Converter Application Diagram II In the figure below the Converter is functioning as a server aggregation for an enterprise or LAN configuration The nodes can be situated 120km apart and the Converter is creating a long distance link between nodes using long haul single mode fiber Fast Ethemet Switch Fast Ethemet Switch Single Mode Single Mode LH Single Mode 120 000 m 00 Bose TXto FX Converter 400Base TXto FX Converter E 100 m 60km 60km 7 Em UTP UTP gt ms 400 Base FX M M to SM Converter Application Diagram 111 In the figure below the Converter is functioning as a high speed dedicated link within a campus network configuration It is providing a 100Mbps full duplex 4km link with multi mode fiber between networking nodes Fast Ethemet Switch Fast Ethemet Switch Multimode Multimode Total 4 000 m 400 Base TXto FX Converter 100Base FX WW to SM Corverter 400Base TX to FX Converter 2km UTP 20 100Base FX Multi mode to Single Mode Converter VOLKTEK CORPORATION 4F No 192 Lian Cheng Road Chung Ho Taipei 235 Taiwan ROC TEL 86 2 8242 1000 FAX 886 2 8242 3333 Tech Support 886 800 286 286 ISO 9001 Certified 21
3. 100Base FX Multi mode to 100Base FX Single Mode Converter Wy OLKTEK nnecting Communities NXF 708 Series User s Manual COPYRIGHT All rights reserved No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means whether electronic mechanical photo copying recording or otherwise without the prior written permission of the publisher pia FCC WARNING This equipment has been tested and found to comply with the limits for class A device pursuant to part 15 of FCC rules These limits are designed to provide reasonable protection against harmful interference in a commercial installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communication Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user s own expense CE lt This is Class A product In domestic environment this product may cause radio interference in which case the user may be required to take adequate measures us Take special note to read and understand all content given in the warning boxes A A Warning Table of Contents 1 Introduction 1 About This Guide eese 1 WelCcOlTi8 de
4. able distances can be greatly increased These Converters have been designed to support both ST and SC fiber optic connectors in Multi mode and SC Single mode configurations This allows it to connect up to 100Base networks using the existing connectors and fibers used in today s networking environments At full duplex these converters can create potential distances of up to 120km with long haul single mode to long haul single mode fiber between two respective nodes Note is not recommended to use the Converter in half duplex mode as back to back distance for multi mode fiber will only be 412m 100Base FX Multi mode to Single Mode Converter Due to the different types of connectors available and the modes of operation in use there are several converter combinations available See table below Operation Mode Single to Single mode sc Multi to Single mode sc Multi to Single mode sc Multi to Multi mode sc Multi to Multi mode ST Multi to Multi mode ST Converter connectors are Mode and Frequency Length dependant Converter view with ST and ST connectors 100Base FX Multi mode to Single Mode Converter Converter view with ST and SC connectors Single Mode Fiber Fiber Port of Status Port of SC or LEDs SC type ST types 100Base FX Multi mode to Single Mode Converter 3 Installation Installing Your Converter In this chapter we will take a look at how to install converters within its operating e
5. and electrical current in your country 100Base FX Multi mode to Single Mode Converter Connecting Fiber Cable When connecting fiber cable to a 100BASE FX port on the Converter be sure the correct type ST or SC connector is used Follow the steps below to properly connect fiber cable Remove and keep the ST SC port s rubber cover When not connected to a fiber cable the rubber cover should be replaced to protect the optics 2 Check that the fiber terminators are clean You can clean the cable plugs by wiping them gently with a clean tissue or cotton ball moistened with a little ethanol Dirty fiber terminators on fiber optic cables will impair the quality of the light transmitted through the cable and lead to degraded performance on the port 3 Connect one end of the cable to the ST SC port on the Converter and the other end to the ST SC port on the other device 4 Check the corresponding port LED on the Converter to be sure that the connection is valid Refer to the LED chart in next section Note When inserting the cable be sure the tab on the plug clicks into position to ensure that it is properly seated A Warning Because invisible laser radiation may be emitted from the aperture of the fiber port when no cable is connected avoid exposure to laser radiation and do not stare into the open apertures 100Base FX Multi mode to Single Mode Converter 4 LED Indicators LED Table This Converter has LED indica
6. ng into the Chassis 16 100Base FX Multi mode to Single Mode Converter Installing the Converter Once the Converter has been attached to the bracket it can be installed into the Chassis Special care must be taken to ensure the correct mating of the power connector Align the Converter so that it fits between the upper and lower guide rails A Warning Always ensure that the converter power socket is positioned at the base of the Chassis Never force the Converter into the Chassis check power socket position and alignment p R 100Base FX Multi mode to Single Mode Converter Rear view of Chassis and specifications KL Rear View of Chassis with AC Power Supply Power 100 240V AC Optional 12V Adapter Dimensions 109 x 174 x 44 3 mm Lx W x H Power 48V DC Optional 12V Adapter Dimensions 109 x 174 x 44 3 mm Lx W x H 100Base FX Multi mode to Single Mode Converter Appendix C Application Diagram To effectively expanding a Fast Ethernet network position two converters back to back as illustrated Application Diagram In the figure below the Converter is functioning as a high speed bridge between converters creating increased distance between each user node on the local area network It is providing a 100Mbps full duplex 22km link using single mode and multi mode fiber Fast Ethemet Switch Fast Ethemet Switch Single Mode Multianode Total 22 000 m Long Haul Total 62 000
7. nvironment First it is important to unpack the Converter and ensure that all the components listed in Package Contents present e Location e Installing Converter e Desktop Installation e Powering On Unit e Connecting Fiber Cable 100Base FX Multi mode to Single Mode Converter Location The location selected for installing the Converter may greatly affect its performance When selecting a site we recommend considering the following rules 1 Install the Converter in a fairly cool and dry place See Technical Specifications for the acceptable temperature and X humidity operating ranges 2 Install the Converter in a location free from strong electromagnetic field generators such as motors vibration dust and direct exposure to sunlight 3 Leave at least 10cm of space at the front and rear of the unit for ventilation 4 Affix the provided rubber pads to the bottom of the Converter for grip and to protect the case from scratching Install the Converter This Converter utilizes ports with fiber connectors functioning under the Fast Ethernet protocol 100Base FX Multi mode to Single Mode Converter Desktop Installation Follow the instructions listed below to install the Converter onto a desktop location 1 Locate the Converter in a clean flat and safe position that has easy access to AC power 2 Affix the four 4 self adhesive rubber pads to the underside of the Converter 3 Apply AC power to the Conve
8. rter The green PWR LED on the front panel should light 4 Connect cables from the network partner devices to the ports on the front panel The green LNK LED on the front panel associated with the port should light 5 This Converter can also be mounted on a vertical surface Simply use the underside of the unit as a template to measure and mark out the position of the holes on to the surface where the unit is to be installed Then use the two screws provided to mount the Converter firmly in place A Warning Please exercise caution when using power tools Also install this unit away from damp or wet locations or in close proximity to very hot surfaces These types of environments can have a detrimental effect on the converter and cables An ideal location is a lightly cooled place such as a typical equipment room 100Base FX Multi mode to Single Mode Converter Powering On Unit The Converter uses external power supply 12V DC at 0 8A frequency 50 60 Hz 1 Insert the power cable plug directly into the receptacle located at the back of the device 2 Plug the power adapter into an available socket 3 Check the front panel LEDs as the device is powered on to verify that the Power LED is lit If not check that the power cable is correctly and securely plugged in Note For International use you may need to change the AC power adapter cord You must use a power cord set that has been approved for the receptacle type
9. sis or the single slot mini chassis with internal power supply e External power supply e FCC Class A and CE approved 100Base FX Multi mode to Single Mode Converter Specifications Standard Connector Max Distance Unit LEDs Port LEDs Power Temperature Humidity Emissions Dimensions IEEE 802 3u Depending on model ST or SC fiber optic Fast Ethernet Multi mode 2km Single Mode 20km Long Haul Single Mode 60km Power illuminated for normal operation Link illuminated when connectors are attached Receive flashing or illuminated when receiving data packets External power supply 12V DC at 0 8A Operating 0 C to 50 C Storage 20 C to 70 C Operating 10 to 90 RH Storage 5 to 90 RH FCC Part 15 of Class A amp CE Approved 109 2 x 73 8 x 23 4 mm LxWxH Go to Location 100Base FX Multi mode to Single Mode Converter Package Contents The Converter package should include e One converter e One AC adapter for external power supply e Four pieces self adhesive pads e One user s manual Go to Installing Your Converter 100Base FX Multi mode to Single Mode Converter 2 Hardware Description Product Overview The Converter range is primarily designed for network or data installations that require extended fiber distances between 850nm 1310nm and 1550nm fiber media for Fast Ethernet Used individually or in conjunction with other converters the fiber c
10. st one media converter The Chassis provides protection for converter units and an option of AC or DC power supplies Now network designers can plan their Ethernet Fast Ethernet ATM or Gigabit networks without having to worry about the power source Furthermore its unique sizes allows it to be installed in locations where space is limited Features e Simple and easy to install e Adds fiber connectivity to otherwise copper based networks e Supports 10 100 1000Base copper fiber single multi mode converters with RJ 45 ST SC MT RJ VF 45 LC WDM connectors e Accommodates one media converter e Suitable for all size of networks in all locations e Provides internal AC or DC switching power supply e Made from high quality durable steel e Optional external redundant power adapter 15 100Base FX Multi mode to Single Mode Converter Affixing Brackets We have supplied 2 special brackets that easily attaches to the Converter This allows for the secure placement of the converter into the Chassis It also seals off the front of Chassis and allows it to function correctly Step 1 Using a Phillips screwdriver remove two screws from the side panels on the converter F Step2 Place the converter and brackets on a flat horizontal surface as illustrated above Secure the brackets by replacing the screws Ensure that the rails are flush mounted with the underside of the converter The converter is now ready for loadi
11. tors located at the front of the device The LEDs have been designed to give easy at a glance network status and provides real time connectivity information Please see below for an interpretation of their functions LED Indicators LED Condition Status Converter is receiving PWR On Green Off Power off or failure On Green Illuminated when connectors are attached LNK Flashing Data traffic passing Green through port Off No link established On Amber Receiving data packets RCV Receiving data packets at Flashing a slower rate Off No data packets received 13 100Base FX Multi mode to Single Mode Converter Cables Appendix A The following are some recommendations as to what you should and should not do when installing cables Remember cables are the deciding factor in network performance Try to maintain a bend radius of min 4x the diameter of the cable for UTP and 100x for fiber Place cabk ties at regular intervals do not over tighten cable ties try to avoid using with fiber 14 Try not to allow the cableto twist too much this creates a strain on the internal cables Do not stretch the cable especially on corners in vertical cable trays and when spanning long distances 100Base FX Multi mode to Single Mode Converter Appendix B Mini Converter Chassis The Chassis was developed to accommodate ju
12. tte teet ete recto cis 1 PUrpOS6 teet fe ERE RE 1 5 1 2 3 Package Contents 4 2 Hardware Description 5 Product Overview 4 00 5 222 0 8 Installing Your 8 9 Install the 9 Desktop Installation 10 Powering On Unit 11 Connecting Fiber 12 4 LED 13 LED Table ac Ree ie Rea 13 Appendix 14 14 15 Mini Converter 15 Affixing Brackets sss 16 Installing the Converter 17 Rear view of Chassis and specifications 18 19 Application Diagram
Download Pdf Manuals
Related Search