Hardware manual EPV3TBR
Contents
1. Connector 2 power supply not isolated 24 VAC or 20 40 VDC or isolated 12 24 VAC or 15 40 VDC according to the model Terminal Meaning 4 power supply 5 power supply page 8 of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 A The maximum length of the connecting cables of the power supply is 10 m 32 8 ft In the models with not isolated power supply this must galvanically be isolated from the one of the other devices connected in the network 3 2 Additional information for electrical connection do not operate on the terminal blocks with electrical or pneumatic screwers if the interface has been moved from a cold location to a warm one the humidity could condense on the inside wait about an hour before supplying it test the working power supply voltage working electrical frequency and working electrical power of the interface they must correspond with the local power supply disconnect the local power supply before servicing the interface do not use the interface as safety device for repairs and information on the interface please contact Evco sales network page 9 of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 114VTOUHWEO1 4 CONFIGURATION 4 1 Preliminary information The following table shows the main meaning of the buttons Button Meaning esc button escape hereinafter called button ESC lt button move to left herei2. of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 7 TECHNICAL DATA 7 1 Technical data Purpose of control user interface for programmable controllers Construction of control electronic device to be incorporated Box self extinguishing transparent 3 118 0 x 111 0 x 26 7 mm 4 645 x 4 370 x 1 051 in ize Size refers to the interface with connector 1 and connector 2 properly plugged the installation is possible by panel built in by wall in traditional box like 506 by BTicino by wall on the support CPVWO00 by Evco to order separately look at chapter Installation 6 ACCESSORIES Fixing screws are always supplied by the builder At the front of the interface one can apply the plates CPVP by Evco to order separately made in plastic material and available in two different colorations white and black look at chapter 6 ACCESSORIES IP40 IP65 for panel mounting with gasket 0027000007 to order separately look at chapter Frontal protection degree 6 ACCESSORIES extractable male female terminal blocks power supply and CAN port 6 poles telephone connector programming port The maximum length of the connecting cables of the CAN port of the interface depends on the baud rate of the CAN communication as follows 1 000 m 3 280 ft with baud rate 20 000 baud Connections i 500 m 1 640 ft with baud rate 50 000 baud 250 m 820 ft with
3. turned supplied CAN RY it provides information on the status of the receiving line of the CAN port CAN Na i tee it provides information on the status of the transmitting line of the CAN port TX page 15 of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 6 ACCESSORIES 6 1 Frontal plates CPVP by Evco 1 1 1 Available models The following table shows the available models and the respective main features Code Main features CPVP00 plastic material white CPVPOI plastic material black 1 1 2 Size Size in mm in 112 0 4 409 133 0 5 236 6 2 Support for wall mounting CPVW00 1 1 3 Available models The following table shows the available models and the respective main features Code Main features CPVWO00 plastic material white page 16 of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 1 1 4 Size Size in mm in Ya O A OL 92 0 3 622 116 0 4 566 O_O a Lasi da i 94 0 3 700 138 0 5 433 gt 6 3 Gasket 0027000007 1 1 5 Available models The following table shows the available models and the respective main features Code Main features 0027000007 black to get a frontal protection degree IP65 only in case of panel mounting 1 1 6 Size Size in mm in k 106 0 ia ir 118 0 ue er page 17
4. 0K 500 000 baud Auto the interface recognizes the baud rate automatically on condition that it is one of the those mentioned above One suggests modifying the value of the parameter and assign each device in the network the same baud rate CAN Network Net Timeout 240 s Remote or of the devices in the network CAN communication time out after this time without CAN communication with a device this will be excluded by the network CAN Network Network Node 1 1 32 127 due Remote or of the devices in the network CAN nodes address example for 2 1 node 2 node s address Modbus Address 247 25 Modbus address reserved Modbus Parity page 13 of 22 even Modbus communication parity reserved none no parity odd odd even even Evco S p A Vtouch Hardware manual ver 1 01 Code 114VTOUHWEO1 Modbus communication baud rate reserved 1200 1 200 baud 2400 2 400 baud 4800 4 800 baud Modbus Baudrate 9600 9600 9 600 baud 19200 19 200 baud 28800 28 800 baud 38400 38 400 baud 57600 57 600 baud Modbus communication stop bit number Modbus Bit Stop 1 bit d reserve 4 4 Configuring a device through the interface Operate as follows 1 fs ih Switch off the power supply of the device and of the interface Connect the device to the interface thr
5. CAL CONNECTION Avsiisna niles ARL RRO RIE RARA Ae 8 3 1 Electrical connectioni t maiala TERN I III II 8 3 2 Additional information for electrical connect Oni s alla lia allena ia lalanena ites 9 4 CONFIGURATION siii a RAR a ad ped ad aera at eer oon aaa Agy 10 4 1 Preliminary mforimation iene stai alain 10 4 2 Conti purine the interface esses a a ER ER E E aan nate dh II SERRE SO a 10 4 3 List of Configuration parameters titani ina Sai ail vii ia giliui a ALLO lille liu ili ill lil lil ced iii LUI 11 4 4 Configuring a device through the interface ssri nna e n a ssh Lalla lalla i 14 5 SIGNAL S ts fo REA RIO INI N IRA O Aa 15 Sal s Sista sissies LIO NILE ga A ee LOR E NSE LEN RA i EA AR al 15 6 ACCESSORIES ciccia REA ORALE RIA OO sa serevedaredenarebeseureernness 16 6 1 Erontal plates CPVP byEycorm t usi ella ei RA LL e RAOUL AR A E E ERE 16 SA Avallablesmodels iii EL LL IO I 16 2 SIZE E ERE RICE I RAPIRE E AE SEA I TRN AEREI I OI RE EAE REA FE SIANO SANI VERRI DONA BRIO 16 6 2 Support for wall mounting CEVWOO eo NANO ER eet ecard Ao 16 2133 Avallable models utrac enel oa lio ilaele 16 4 SIZE Asian DA EE ala ERA a Ri MALO ELARIO E era 17 6 3 Gasket 0027000007 GL IIC RS LO E O ORA 17 5 Available ModE E a a a sdevsbic custsibu edeusbec doe shive sass bis ca oiSbs ed Lelli leo lele lui lei alleluia lu 17 6 SIZE RI RE INIT II RARO RI ara 17 ts TECHNICAL DATA irta ilaele el osa linea 18 eM CERRO RE RR RR RR RR cveuansa
6. Evco S p A Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 eVCoO Every ControlGroup Vtouch CANBUS USER INTERFACE WITH TOUCH SCREEN LCD GRAPHIC DISPLAY ENGLISH HARDWARE MANUAL ver 1 01 CODE 114VTOUHWEO01 page of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 Important Important Read these instructions carefully before installing and using the instrument and follow all additional information for installation and electrical connection keep these instructions close to the interface for future consultations The interface must be disposed according to the local legislation about the collection for electrical and electronic equipment page 2 of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 Index 1 MRO VOTON 00 seats as ak gs ee iia IRE IRE RR RO RE RI NR SRI 4 1 1 Introduction aaa bea RE E E EN A RARI 4 1 2 Available models for the programmable controllers of the family C pro0 5 1 33 Available models for the programmable controllers of the family C pro 3 eesceseseeseeecseeseseeseseesesacsecsececsesaeseescsesseeecsecaeesseeesseeacsesaeees 5 Di SIZEAND INSTALEATION icnae eli EEEE I IAA 6 Zdi SIAO I RR vou de E E TE RARE RR RO IRON RR 6 2 2 Installation anice lean IGO GN AEDES ES ene ENEA ANI 6 2 3 Additional information for Installation series rnea aA OS SE ESEE SEASTAR STER EEIN EEEE sauenvea ARIANNA T 3 ELECTRI
7. alue 28 Press and release button ENTER or button RIGHT to confirm the value and modify the following field 29 Repeat steps 26 and 27 30 Press and release button ESC to go back to the Main menu To quit the procedure 31 Press and release over and over again button ESC possible modifications will not be saved A Switch off the power supply and then switch it on after the modification of the configuration 4 3 List of configuration parameters Submenu Parameter Min Max Unit Default Description Date Char Parameters Date separator ASCII character Separator page 11 of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 Year format Parameters Year format YY YY two numbers for example 10 YYYY four numbers for example 2010 Date format yymmdd year month and day Parameters Date format ddmmyy mmddyy month day and year ddmmyy day month and year Time Char Parameters Time separator ASCII character Separator Showing the seconds in the real time Parameters Time With Sec YES YES yes Time format Parameters Time AM PM NO NO 24h for example 15 20 YES 12h for example 3 20 PM Backlight mode OFF backlight is never lit ON backlight is always lit Parameters Backlight Mode TIME TIME backlight is lit the time one has set with parameter Backlight Timeout sinc
8. baud rate 125 000 baud 50 m 164 ft with baud rate 500 000 baud According to the default settings the interface recognizes the baud rate automatically on condition that it is one of the those mentioned above Working temperature from 0 to 50 C 32 to 120 F 10 90 of relative humidity without condensate Pollution situation 2 or more page 18 of 22 Evco S p A Power supply Vtouch Hardware manual ver 1 01 Code 114VTOUHWEO01 according to the model 12 24 VAC min 11 4 VAC max 27 6 VAC 50 60 Hz 3 VA approximate isolated or 15 40 VDC 3 W approximate isolated 24 VAC min 20 4 VAC max 27 6 VAC 50 60 Hz 3 VA approximate non isolated or 20 40 VDC 2 W approximate non isolated supplied from a class 2 circuit The maximum length of the connecting cables of the power supply is 10 m 32 8 ft In the models with not isolated power supply this must galvanically be isolated from the one of the other devices connected in the network Protect the power supply with an UL listed or recognized fuse rated 80 mA T if the user interface is powered with 15 40 VDC 250 mA T if the user interface is powered with 12 19 VAC 160 mA T if the user interface is powered with 19 24 VAC Overvoltage category MI Real time clock data maintenance in absence of power supply 2 days will battery fully charged Battery charging time 2 min without interruptions th
9. e battery is charged by the power supply of the interface Alarm buzzer incorporated Display 240 x 140 pixel single colour touch screen LCD graphic display black with rearlighting through white LED Communication ports 2 ports 1 non optoisolated CAN port 1 programming port page 19 of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 Notes page 20 of 22 Evco S p A Vtouch Hardware manual ver 1 01 PT January 2011 Code 114VTOUHWEO1 Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 This document belongs to Evco unless you are authorized by Evco you can not publish this document Evco does not take any responsibility about features technical data and possible mistakes related in this document Evco does not take any responsibility about damages coming by the non observance of additional information Evco reserves the right to make any change without prior notice and at any time without prejudice the basic safety and operating features page 21 of 22 Evco S p A A y EveryControlGroup Evco S p A Via Mezzaterra 6 32036 Sedico Belluno ITALIA Tel 0437 852468 Fax 0437 83648 info evco it www evco it page 22 of 22 Vtouch Hardware manual ver 1 01 Code 114VTOUHWEO1
10. e the last operation with the buttons Backlight Backlight duration only if parameter Backlight Parameters 0 240 s 60 Timeout Mode has value TIME Local or of the interface CAN communication time out after this time without CAN Parameters T O Timeout 0 240 s 60 communication the display will show Checking and the PIO of the interface will be disabled Showing the indication Loading while Parameters Print Loading NO loading a page YES yes CAN Network submenu access password time out after this time without one has operated Parameters Password Timeout 0 240 s 60 with the buttons to gain access again to the submenu one has to set the password again Parameters Contrast 100 250 160 Display s contrast page 12 of 22 Evco S p A Parameters Buzz On Key Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 Modality to use to utter the beep while pressing an area of the user interface 0 Il the beep is never uttered 1 the beep is always uttered 2 the beep is uttered only if the area is sensitive Parameters Print Frame Showing frames instead small size pages 1 yes CAN Network MyNode 127 ae 99 Local or of the interface CAN node s address CAN Network Master YES The interface always works as master CAN Network Baud Auto CAN communication baud rate 20K 20 000 baud 50K 50 000 baud 125K 125 000 baud 50
11. esse asiey ish IE VII AER EO ET 18 page 3 of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 114VTOUHWE01 1 INTRODUCTION 1 1 Introduction Vtouch is a new and innovative user interface for the programmable controllers of the family c pro that support the CAN bus and for the programmable controllers of the family c pro 3 The main features of the interface are the possibility to communicate to the user a great deal of information and the remarkable ease of control these features are due to the use of a 240 x 140 pixel single colour touch screen LCD graphic display black with rearlighting through white LED to the 6 buttons with preset functions membrane keyboard and to the CAN bus for the connection to the controllers This last also allows the use of the interface in multimaster networks Thanks to its constructive features Vtouch offers several mounting typologies this is possible by panel at the front of units of machines for refrigeration or for air conditioning of electrical panels and as well as in all those applications where a frontal protection degree IP65 is required built in by wall in traditional box like 506 by BTicino by wall on the support CPVW00 by Evco to order separately Also the necessity to customize the interface in order to integrate it aesthetically in residential and commercial environments is satisfied by Vtouch since at the front of the interface one can apply both the plate
12. nafter called button LEFT A button increase hereinafter called button UP Vv button decrease hereinafter called button DOWN D button move to right hereinafter called button RIGHT button confirm hereinafter called button ENTER 4 2 Configuring the interface To gain access to the procedure operate as follows 1 Switch off the power supply 2 Keep pressed buttons ESC and RIGHT 3 Switch on the power supply 4 When the display shows the following menu hereinafter called Main menu release buttons ESC and RIGHT V TOUCH Parameters Contrast CAN Network Modbus Info Data e ora reale It is also possible to show the Main menu operating as follows 5 Make sure the power supply is switched on 6 Keep pressed 2 s buttons LEFT and ENTER the display will show the following men hereinafter called Network Status menu address status more gt gt local 99 ok back to the Main menu node 1 1 gt gt node 2 0 gt gt node 3 0 gt gt node 4 0 gt gt node 5 0 gt gt node 6 0 gt gt page 10 of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 he Press and release button ENTER the display will show the Main menu To gain access a submenu operate as follows 8 From step 4 press and release button UP or button DOWN to select the submenu 9 Press and release button ENTER A The access to the CAN Ne
13. of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 2 SIZE AND INSTALLATION 2 1 Size Size in mm in panel cut out Le 48 5 1 909 gt 111 0 4 370 a D SDAP Ie MM i fs at Le lt 118 0 4 645 Size Minimum Typical Maximum A 104 0 4 094 104 0 4 094 104 8 4 125 B 70 0 2 755 70 0 2 755 70 8 2 787 C 22 0 0 866 23 0 0 905 24 0 0 944 D 40 8 1 606 41 8 1 645 42 8 1 685 2 2 Installation The installation is possible by panel built in by wall in traditional box like 506 by BTicino by wall on the support CPVW00 by Evco to order separately look at chapter 6 ACCESSORIES The following drawing shows the installation by panel with 4 screws supplied by the builder page 6 of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 At the front of the interface one can apply the plates CPVP by Evco to order separately made in plastic material and available in two different colorations white and black look at chapter 6 ACCESSORIES 2 3 Additional information for installation working conditions working temperature humidity etc must be between the limits indicated in the technical data do not install the interface close to heating sources heaters hot air ducts etc devices provided with big magnetos big speakers etc locations
14. ough the CAN port look at chapter 3 ELECTRICAL CONNECTION Switch on the power supply of the device and of the interface Operate on the interface to set parameter Network Node look at chapter 4 CONFIGURATION Parameter Network Node belongs to the CAN Network submenu According to the default settings the CAN node s address of a controller has value so operate on the interface to set parameter Network Node to 1 1 and the CAN node s address of an expansion has value 2 so operate on the interface to set parameter Network Node to 2 2 Keep pressed 2 s buttons LEFT and ENTER of the interface the display will show the Network Status menu Network Status CAN address status more local 99 ok gt gt node 1 1 ok gt gt node 2 2 ok gt gt node 3 0 gt gt node 4 0 gt gt node 5 0 gt gt node 6 0 gt gt Press and release button UP or button DOWN to select the device Press and release button ENTER the display will show the device s Main menu Operate as indicated in paragraph 4 2 Configuring the interface Switch off the power supply of the device and then switch it on after the modification of the configuration page 14 of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 5 SIGNALS 5 1 Signals The following table shows the meaning of the LEDS at the back of the interface LED Meaning POWER if it is lit the interface will be
15. s CPVP by Evco to order separately made in plastic material and available in two different colorations white and black and the numerous plates series Living and Light by BTicino Vtouch also has got real time clock alarm buzzer page 4 of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 1 2 Available models for the programmable controllers of the family c pro The following table shows the available models and the respective main features Code Main features Not isolated power supply 24 VAC or 20 40 VDC 240 x 140 pixel touch screen LCD graphic CPV3L3C4 display real time clock alarm buzzer Isolated power supply 12 24 VAC or 15 40 VDC 240 x 140 pixel touch screen LCD graphic CPV3L3C7 display real time clock alarm buzzer For further models contact the Evco s sales network Evco at the address sales evco it 1 3 Available models for the programmable controllers of the family c pro 3 The following table shows the available models and the respective main features Code Main features Not isolated power supply 24 VAC or 20 40 VDC 240 x 140 pixel touch screen LCD graphic EPV4TBR display real time clock alarm buzzer Isolated power supply 12 24 VAC or 15 40 VDC 240 x 140 pixel touch screen LCD graphic EPV3TBR display real time clock alarm buzzer For further models contact the Evco s sales network Evco at the address sales evco it page 5
16. subject to direct sunlight rain humidity dust mechanical vibrations or bumps according to the safety legislation the protection against electrical parts must be ensured by a correct installation of the interface the parts that ensure the protection must be installed so that you can not remove them if not by using a tool page 7 of 22 Evco S p A Vtouch Hardware manual ver 1 01 Code 1I4VTOUHWEO1 3 ELECTRICAL CONNECTION 3 1 Electrical connection programming port connector 2 evco Every Control Group Vtouch connector 1 Position micro switch 4 on position ON to plug in the termination of the CAN port micro switches 1 2 and 3 are reserved The following tables show the meaning of the connectors Connector 1 CAN port Terminal Meaning 1 ground 2 signal 3 signal A The maximum length of the connecting cables of the CAN port of the interface depends on the baud rate of the CAN communication as follows 1 000 m 3 280 ft with baud rate 20 000 baud 500 m 1 640 ft with baud rate 50 000 baud 250 m 820 ft with baud rate 125 000 baud 50 m 164 ft with baud rate 500 000 baud Connect the CAN port of the interface using a twisted pair According to the default settings the interface recognizes the baud rate automatically on condition that it is one of the those mentioned above hereinafter one suggests setting the same baud rate of the others devices in the network
17. twork submenu is protected by password To gain access to the CAN Network submenu operate as follows 10 From step 4 press and release button UP or button DOWN to select the submenu CAN Network 11 Press and release button ENTER 12 Press and release again button ENTER 13 Press and release over and over again button DOWN to set 19 14 Press and release button ENTER To modify a configuration parameter belonging to the Parameters submenu to the CAN Network submenu or to the Modbus submenu operate as follows 15 From step 9 press and release button UP or button DOWN to select the parameter 16 Press and release button ENTER 17 Press and release button UP or button DOWN to modify the value 18 Press and release button ENTER to confirm the value 19 Press and release button ESC to go back to the Main menu To modify the display s contrast operate as follows 20 From step 4 press and release button UP or button DOWN to select the Contrast submenu 21 Press and release button ENTER 22 Press and release button UP or button DOWN to modify the value 23 Press and release button ENTER to confirm the value 24 Press and release button ESC to go back to the Main menu To modify the real date and time 25 From step 4 press and release button UP or button DOWN to select the item Real date and time 26 Press and release button ENTER 24 Press and release button UP or button DOWN to modify the v
Download Pdf Manuals
Related Search