Stereo Box Manual - Henley Designs Ltd.
Contents
1. 1 is selected the LED over the Input Select button lights up green If Input 2 is selected it lights up red If the optional input expander Pro Ject Switch Box is connected Input Select will also select the additional inputs provided by the Switch Box Volume Adjust the volume to the desired level using the large knob marked Volume on the front panel Audio Trade GmbH Pro Ject Pre Box Revision 1 6 10 1 8 10 3 Replacing batteries Proceed as follows e Slide open the battery case cover e Replace the battery Make sure the battery is the right way round e Close the battery case cover Al Battery type 1 x CR 2032 3V neg Do not dispose the batteries as ordinary domestic refuse Please dispose your exhausted batteries at the appropriate collection sites usually located at supermarkets and drugstores Technical specifications Pro Ject Stereo Box Power output 2 x 20W 30W at 8ohms 4ohms both channels driven Frequency response 20Hz 20kHz 0 2dB Channel separation gt 40dB at 20kHz Noise floor gt 100dB A weighted THD lt 0 05 ot 10W Gain 22dB Line level inputs 2 pairs RCA Phono sockets Input impedance 20kohms Trigger Switch 2 pole 2 5mm co axial jack Speaker connectors 4mm banana plugs spades connectors or naked wire Outboard power supply 20V 3A DC peak 7A DC suitable for your country s mains supply Power consumption 20V 3A DC Replacement battery remote control 1 x CR 202. per channel Remote switching Optional Pro Ject Switch Box The Trigger Switch socket connects the input expander Pro Ject Switch Box The Switch Box provides four extra line level inputs A 30cm remote switching cable is supplied with the Pro Ject Switch Box for connecting the Trigger Switch socket of the Pro Ject Stereo Box Do not use this socket for any other connections for which it is not designed Mains power connection The unit is supplied with a power supply suitable for your country s mains supply Check the label before connecting to ensure compliance with the mains rating in your house Connect the low voltage plug from the power supply to the Power 20V socket before connecting the power supply to the mains 2 Audio Trade GmbH Pro Ject Stereo Box gt Revision 1 6 10 1 8 10 Remote control ON OFF nori turns the unit on or back into standby The blue LED on the front panel shows that the unit is powered on wo co and adjust the sound volume om CH and select the inputs Front panel controls O 102 Input O QO Select Volume gt O Power O Stereo Box d Stand By The switch marked Power press and hold to switch into standby mode on the front panel turns the unit on or back into standby The blue LED on the front panel shows that the unit is powered on Input selector After the unit is powered on pressing the Power button selects the In 1 and In 2 inputs in turn If Input
3. 32 3V Dimensions W x H x D D with sockets 103 x 36 x 103 122 mm Weight 720g without power supply Service Should you encounter a problem which you are not able to alleviate or identify please contact your dealer for further advice Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use Modification or change to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawtul rights of the customer PRO JECT is a Registered Trademark of H Lichtenegger The information was correct at the time of going to press The manufacturer reserves the right to make This guide was produced by Audio Trade GmbH changes to the technical specification without prior Copyright 2008 All rights reserved notice as deemed necessary to uphold the ongoing process of technical development 4 Audio Trade GmbH Pro Ject Stereo Box gt Revision 1 6 10 1 8 10
4. A U D Om Ss YSTEMS INSTRUCTIONS FOR USE Pro Ject Stereo Box Dear music lover thank you for purchasing a PRO JECT AUDIO amplifier In order to achieve maximum performance and reliability you should study these instructions for use carefully V Warning of a hazard for the user the unit or possible misuse neg Important notice Help to protect the environment If you are not going to use the amplifier for an extended period of time e g vacation we suggest to disconnect it from the AC mains Please be certain that the amplifier is in standby mode prior to unplugging the power supply from the AC mains Connectors O Trigger Switch gt Right Left Right ao Ini In O i 9 Make all connections whilst the amplifier is disconnected from the power supply Take care to connect the left and right channels correctly The right channel is usually marked red V the left channel black or white The red speaker terminals carry the positive signal the black speaker terminals the negative signal Make sure the polarity of the connection is correct at each end of the cables Inputs Line level sources such as CD player radio or TV can be connected to the input sockets marked In 1 or In 2 Connection to the speakers The output terminals accept loudspeaker cables terminated with 4mm Banana plugs spades connectors or naked wire V Only connect one loudspeaker with an impedance not less than 4 Ohm
Download Pdf Manuals
Related Search