CopyBox USB Duplicator
Contents
1. USB Duplicator CERTIFIED USB A eo A ee 5 l Hi Dt a iin Dom p User Manual v 7 0 X rs r Virtual Vision Table of Contents Introduction 1 Features 2 Control Panel Overview 3 Specifications Warning Synchronous Asynchronous Mode 1 Synchronous Mode 2 Asynchronous Mode Menu Overview 1 Copy 2 Compare 3 Copy Compare 4 Capacity Check 5 Utility 5 1 Format FAT32 9 2 Format exFAT 5 3 M easure Speed 5 4 Quick Erase o Full Erase 5 0 DOD Erase 3 7 Change Disk Signature 5 8 M edia Information 5 9 Device Model 5 10 System Information 5 11 System Update 6 1 Copy Area 6 2 Asynchronous M ode 6 3 Smaller Target 6 4 Unknown Format 6 5 Check Before Copy 6 6 Display Mode 6 7 Start up Menu 6 8 Button Beep 6 9 Show Result Time 6 10 Boot Password 6 11 Setup Password 6 12 Language 6 13 Clear Setup 6 14 Performance WO WO WO CO 09 O SS OO dd V E A 00 0 N N N RRR RP Te RRWWWWWNNPFPRRFEF OO OO Introduction This duplicator system is designed and developed based on the FPGA from the world famous semiconductor company XILINX Every processing channel is parallel to each other with its own control unit therefore the duplicator will not sacrifice soeed for the increasing number of targets loaded always remain the same and fast copy speed The duplicator supports fast copy with multiple file formats created by three major operating systems Windows Linux MAC and ma2. Final result 4 Capacity Check This command allows to verify the device capacity It can detect the actual capacity of devices within 3 seconds 4 Capacity Check Check 8 Result Ready device 8 Pass 8 Fail O Source and target devices inserted Display progress status Final result 5 Utility 5 1 Format FAT32 This option allows to format the target device to FAT32 file format It will not format the source device avoiding accidently erasing the original data content User will be asked if it is sure to format the target devices before the Format process starts Utility Sure to format Format 7 1 Format FAT32 Yes P OF 0 0 Use Aor Y to select option Display progress status Result Pass 7 Fail O Final Result 5 2 Format exFAT This option allows to format the target device to exFAT file format It will not format the source device avoiding accidently erasing the original data content User will be asked if it is sure to format the target devices before the Format process starts Utility Sure to format Format 7 1 Format exFAT Yes P OF O 0 Use Aor Y to select option Display progress status Result Pass 7 Fail O Final result 5 3 Measure Speed This option allows to measure the actual Read and Write speed of the target device This option will NOT alter or erase existing data on the target device Utility 0 Read 20M 1 Read 20M 3 Measure Speed 1sec Write 16 5M 1
3. Y Button Down Forward ESC Button Escape Cancel 3 Specifications Model USB duplicator Target 6 13 20 27 34 41 55 69 83 Operation Standalone No PC or Software is required USB eUSB USB 1 1 2 0 3 0 compatible devices eUSB embedded USB Supported Media Model FAT 16 FAT32 exFAT NTFS Windows Ext2 Ext3 Ext4 Linux HFS HFSHM ac Display 2 line Backlit Monochrome LCD Power Supply 115V or 230V Control Button 4 push button control panel ENT ESC UP DOWN Working 20 80 Humidity Storage 5 95 Working 32 F 167 F Temperature Storage 4 F 185 F ll Warning 1 The duplicator tasks mentioned in this user s manual are as following Copy Compare Copy Compare Capacity Check and the functions under Utility Sub menu such as Format FAT32 Format exFAT Quick Erase Full Erase and DOD Erase 2 All the tasks can be executed in synchronous mode and asynchronous mode except Copy Compare function 3 The Green LED flashes during the execution process of a task After the task is done the Green LED will stay solid if the process is successful otherwise the Red LED will be on if the process is failed 4 Press and hold ESC button during the execution process of a task will stop and exit the execution of the task 5 DO NOT unplug USB drive and flash media from the duplicator during the execution process of a task It may cause damage to the duplicator system and media 6 It is stro
4. copy process The default setting is disable Setup Show Result Time 9 Show Result Time Disable Use Aor Y to select 6 10 Boot Password This option allows to set up password for system boot up to prevent from the unauthorized use of the duplicator The password must be 6 characters Setup Boot Password Boot Password 10 Boot Password Enable Use Aor Y to select Use Aor Y to select Press ENT to confirm 6 11 Setup Password This option allows to set up password for Setup function to prevent from the change of system settings on the duplicator The password must be 6 characters Setup Setup Password Setup Password 11 Setup Password Enable Use Aor Y to select Use Aor Y to select Press ENT to confirm 6 12 Language This option allows to choose the language for display English Spanish Portuguese and Japanese English is the default language Setup Language 12 Language English Use Aor Y to select 13 6 13 Clear Setup This option resets the duplicator back to factory default settings Setup Clear Parameter To Default Clear Parameter To Default 13 Clear S etup Yes All Parameters were cleared Use Aor Y to select 6 14 Performance This option allows to set up the performance for Copy function based on the following modes Speed Balance and Compatibility Speed mode is to execute the Copy function at the fastest speed but may have compatibility issue with
5. show the number of successful and failed target s and execution time Go to section 6 9 Show Result Time to set up the display of time 2 Asynchronous Mode Asynchronous Mode means that the duplicator will read the data from source device into system memory buffer and start to execute a task immediately when target device s inserted Duplicator does not have to wait for all target device s inserted in order to start the execution of the task at the same time No matter the data size of the source device duplicator can asynchronously execute a task if Asynchronous Mode is enabled Go to 6 2 Asynchronous Mode to enable or disable this function a Insert source media into the source channel select the task to execute from the menu and press ENT button Duplicator will start to execute the task now Target devices can be plugged in during the execution process and will start to execute the task immediately Target device can be removed when it finishes the execution process and its green LED is solid on New target device can be plugged into the same channel for execution of the task again LCD display will show the percentage of execution process the number of successful and failed target s Here the percentage of execution process displayed is only for the least processed target device During the execution process the status of each target device can be checked by using the A and Y buttons After the t
6. ask is done for all target devices press ESC button to exit from the task LCD display will show the total number of successful and failed target s and total execution time Go to 6 9 Show Result Time to set up the display of time Don t need to wait for all target devices to be done Each channel executes the task asynchronously IV Menu Overview 1 Copy To copy from source device to target device s please go to 6 1 Copy Area to select the setting first before this step 1 Copy 1 Copy Copy 7 7 8G Source Not Ready Ready device 7 P OF 0 10 No source device Source and target devices inserted Display copy progress Result Copy 7 number of targets 7 8G data to be copied Pass 7 Fail 0 P number of passed i F number of failed 10 rate of progress Final result The process of all tasks are displayed in the same format 2 Compare This command allows to compare the copied target devices against the source for accuracy 2 Compare COMP 7 7 8G Result Ready device 7 P OF 0 80 Pass 6 Fail 1 Source and target devices inserted Display compare progress Final result 3 Copy Compare This command allows duplicator to start Copy process first then follow with Compare process immediately 3 Copy Compare amp COMP 7 7 8G Ready device 7 P OF O 10 Source and target devices inserted Display copy progress Display compare progress Result Pass 6 Fail 1
7. certain brands flash media Balance mode is to execute the Copy function at stable speed and have less compatibility issue with certain brands flash media Compatibility mode is to execute the Copy function at the most stable speed and almost have no compatible issue with flash media The default mode is Speed Setup Performance 14 Performance Speed Use Aor Y to select Version 7 0 All rights reserved 2015 14
8. en you have a source device with unknown file format For instance a source device has 8GB capacity and 50MB of data with unknown file format the duplicator will copy the whole 8GB of content to target device 10 6 2 Asynchronous Mode This option allows to enable or disable Asynchronous Mode By default the Asynchronous Mode is disabled Please refer to Chapter Ill for the detail of Operation on Synchronous and Asynchronous Mode Setup Asynchronous Mode 2 Asynchronous Mode Disable Use Aor Y to select 6 3 Smaller Target If the capacity of the target device is smaller than the source device the duplicator will partly copy or cannot copy Partly Copy is the default setting Setup Smaller Target 3 Smaller Target Partly Copy Use Aor Y to select 6 4 Unknown Format This option allows you to Copy or Skip unknown format If option Skip is selected here the unknown format from source will not be copied during copy process Copy unknown format is the default setting Setup Unknown Format 4 Unknown Format Copy Use Aor Y to select 6 5 Check Before Copy This option allows to check device real capacity before copying By default this option is disabled Setup Check Before Copy 5 Check Before Copy Disable Use Aor Y to select 11 6 6 Display Mode There are three display modes Basic Show Timer and Expert Basic Mode shows the copy progress in general Show Timer Mode displays the t
9. ime used for the task Expert Mode shows the devices with highest copy speed and lowest copy speed and their copy progress respectively By default it is Basic Mode Setup Display Mode 6 Display Mode Basic Use Aor Y to select Copy 1 number of target 2 5G data to be copied P number of passed copies I I F number of failed copies Basic Mode 10 rate of progress Copy 1 number of target 2 5G data to be copied 03 45 copy time used 10 rate of progress Show Timer Mode L A 10 number of targets in copy process 4 2303M P 0 number of targets passed copy speed and data copied so far 1 2183M the port with lowest copy speed and data copied so far l l l 1 2183M 4 2303M the port with highest copy l Expert Mode l l l 6 7 Start up Menu Choose one of the following as the default start up function Copy Compare Copy Compare Capacity Check Utility and Setup The default start up function is Copy Setup Start up Menu 7 Start up Menu Copy Use Aor Y to select 12 L 6 8 Button Beep This option allows to set up button sound from the following options Button amp Warning OFF Warning only The default setting is Button amp Warning Setup Button Beep 8 Button Beep Button amp Warning Use Aor Y to select 6 9 Show Result Time This option allows to enable or disable the display of copy time after finishing the
10. kes mirror copies of data efficiently 1 Features gt Each processing channel has its own control unit and operates independently with dedicated bandwidth of up to 33MB per second Standalone operation No PC or software is required minimizing possible computer virus infection Instant power on and off no warm up or cool down required Easy to use One Touch copy operation Compare function available for verification of copy accuracy Menu options are user friendly and easily accessed through the 4 button control panel Use Aor Y button to scroll through the options and view the operation status of each channel on the 2 line backlit LCD display Support Synchronous and Asynchronous copy modes for best operation efficiency Powerful 32 bit CRC checksum to assure data integrity Heavy duty hardware construction for commercial production or personal use 115V and 230V switching power supply maximizes portability for operation anywhere Designed to save users time and effort in creating multiple copies quickly and reliably Unique source data analysis to copy data area only to achieve highest efficiency Supports multiple file formats Windows FAT 16 32 exFAT NTFS Linux Ext 2 3 4 Mac HFS HFS gt Not only to do copy but also test flash media capacity and reading writing speed M MMMM MMMMMMM 2 Control Panel Overview 2 line backlit LCD A Button ENT Button ESC Button Y Button A Button Up Backward ENT Button Enter OK
11. ngly recommended that the capacities of the source and target media are equal or similar 7 Itis not recommended to use USB card reader to copy different media on the USB duplicator such as CF SD MS cards It may cause damage to the duplicator system and media 8 DO NOT plug in USB or flash media until the duplicator boots up It may cause abnormal results if a USB or flash media with quality issue is plugged in before or during the boot up process lll Synchronous Asynchronous Mode 1 Synchronous Mode Default Synchronous Mode means that the duplicator will start to execute a task after the source and target devices have been inserted and the ENT button is pressed The task will begin and end at the same time for all target devices Any other target device plugged in during the process of a task will not be executed with the task Go to section 6 2 Asynchronous Mode to enable or disable this function a Insert source media into the source channel and blank media into the target channels properly The LCD display will show no source disk when source media is not plugged in yet and show the number of target media inserted when source media plugged in b The green LED will be on if the target device is plugged in properly c Select the task from menu and press ENT button to execute it d During the execution process the status of each target device can be checked by using the A and Y buttons e After the task is done LCD display will
12. r This function allows to change disk signature Attention it will cause error data mismatch if compare the disks after execution of this function Utility D Signatures 0 Result 7 Change Disk Signatures ENT P OF 0 Wait ENT Pass 7 Fail O Display progress status Final result 5 8 Media Information This option displays the information of selected device media such as total Capacity file format and the size of data content a LESS RBBB BRB RBBB RBBB BEE BE BEE BB BB BB BB BB BB ee ee ee E Utility Port Total Capacity gt 8 Media Information File Format Data Size Use Aor Y to select device 5 9 Device Model This option displays the model information of selected device such as device model serial information and firmware version Utility 0 P 0 1 P 1 9 Device Model Model information Model information Use Aor Y to select device 5 10 System Information This option displays general information of the duplicator including controller model system memory size firmware version and number of targets a BEB BR BERBER ERR RRR RRR REPRE RRR Ree eee eee ee ee eee Utility F0107V 128MB Controller Model Memory gt l 10 System Info V1 05 12 1 7 Firmware Target Number Display system information 5 11 System Update This option allows user to update the firmware of duplicator when necessary Please obtain the proper firmware file from manufacturer and save the
13. sec Write 16 6M Display read write speed Use Aor Y to select device 5 4 Quick Erase This option erases the table of content of file system of the target device so it is fast to do Quick Erase There is chance that some files can be retrieved by software Utility Sure to erase Q Erase 7 4 Quick Erase Yes P OF 0 0 Use Aor Y to select option Display progress status Result Pass 7 Fail 0 Final result 5 5 Full Erase This option completely erases the content of target device lt takes longer time to erase and the content will not be retrieved by software Utility Sure to erase F Erase 7 5 Full Erase Yes P 0 F 0 0 Use Aor V to select option Display progress status Result Pass 7 Fail O Final result 5 6 DoD Erase This is to comply with the U S A Department of Defense DoD 5220 standard to fully erase the media by rewriting bit by bit three times to guarantee the data to be permanently deleted It takes the longest time to erase and the content will not be retrieved by software Utility Sure to erase DoD Erase 7 6 DoD Erase Yes P OF 0 0 Use Aor V to select option Display progress status Result Pass 7 Fail O Final result 5 7 Change Disk Signatures Duplicator generates the same disk signatures after copy which may cause computer unable to read the disk correctly when two disks with identical disk signatures are presented or shut down the compute
14. unzipped file under home folder on the flash device DO NOT save the file under sub folder Insert the flash device containing the firmware into the source port of duplicator and press ENT It will update the system reboot the duplicator after update active and operate under the new firmware Utility Update BIOS Update BIOS 11 System Update Identify disc ENT Complete Reboot Looking for firmware 6 Setup 6 1 Copy Area This option allows to select the area on the source device to copy onto the target devices You may select either System And Files to skip all the unoccupied area on the source device or Whole Media By default the copy area is set up as System And Files 6 1 1 System And Files The duplicator first analyzes the file format of source device You may copy only the system and files area to save overall copy time if the file format is FAT16 FAT32 exFAT NTFS Windows EXT2 EXT3 EXT4 Linux and HFS HFS Mac Otherwise the duplicator will copy the entire source device content to the target devices including unoccupied space For instance the source device has 8GB capacity but with only 50MB of data in FAT32 file format The duplicator will copy only the 50MB of data area to the target device hence shortening overall copy time 6 1 2 Whole Media When selected the duplicator copies the entire content on the source device including both the data and empty spaces This option is used wh
Download Pdf Manuals
Related Search