INSTALLATION MANUAL
Contents
1. And Materials needed in installation Installation cable User s Manual and Installation Manual 2 3 Accessories The following accessories are available to HouseControl Magnetic door switch flush and surface mounting Security keypad with proximity tags Remote camera Moisture sensor Siren with light ha Temperature sensor gt N Heat detector Carbon monoxide detector HCE Wireless extension detectors and remote controls 4 HouseControl E Installation Manual 3 INSTALLATION 3 1 Opening Unit s Cover 7 7 There is a small curved indentation on the top of the central unit Place your hand into the indentation and carefully detach the cover The cover must be fastened with screws after installation is me complete The screws are included in the package A 3 2 HCE from Inside Heater Aircon relay see 3 3 Ext relay see 3 3 Camera and data connector gt N Inputs for temperature sensors siren magnetic door switches moisture sensor motion sensor smoke detector security keypad and 12V power supply see 3 3 Cable holder SIM card slot Power switch Tamper switch Manual heating switch red light is on when manual control is used 10 Door security on off switch Do not use your fingers when inserting wires into the spring clips Relays may be damaged if you push your fingers against them INSTALLATION2. You can take a picture with command PICTURE see User s Manual if the multimedia settings are ok Heater relay Send HEATER ON and HEATER OFF messages to the unit and make sure the heater starts and stops Ext relay Send EXT ON and EXT EI messages to the unit and make sure the controlled device works as expected Send ALARM ON and ALARM OFF commands to the unit and make sure that the status light on the security keypad displays the unit s operating mode correctly Unplug the battery backup unit and wait until you receive an alarm message It may take 15 to 30 minutes for the alarm to activate Plug the battery backup unit back in after you received the alarm message and wait until you receive Power OK message Notes Notes TELEMIC Isoharjantie 6 Tel 358 20 728 8740 71800 Siilinjarvi Fax 358 17 462 1212 FINLAND info telemic fi http www telemic net
3. To program security keypad for example if you want to change individual codes you need installer s key and installer s code 1234 Do not change the installer code because if installer s proximity key is lost you cannot program the security keypad anymore Keep the installer s key in a safe place away from the sun light To change monitoring on bring one of the proximity keys in front of the keypad momentarily OK light will flash The round LED light starts blinking and when exit delay is over it stops blinking and stays lighted monitoring is on If you want to cancel operating mode change during the exit delay you can use your key as described The OK light flashes and the round LED light goes off Tip You can silence the siren by using a proximity key without changing the operating mode To change operating mode with code 1 Press SIR 2 Key in the four digit user code 3 Press en INSTALLATION 11 To change user code Switch to programming mode in security keyboard 1 Press Fun and and start blinking 2 Bring installer s key near the keypad You will hear a short signal tone and only blinks 3 Key in installer code 1234 and press You will hear a long signal tone and D starts blinking To program a new user code 4 Press Fun and en starts blinking 5 Press o and en continues blinking 6 Key in a new 4 digit code Press continues blinking 7 Repeat the new 4
4. 3 4 Always use a screwdriver and pointed pliers when inserting wires into the connectors Push spring clips almost directly from the top with a screwdriver Before connecting individual wires to the connectors peel off about 10 cm of the insulation from the cable Join the uninsulated conductor to earth by using a connector strip see separate wiring diagram The DOOR IR motion sensor and FIRE smoke detector inputs have been short circuited with yellow wires This prevents alarms from the inputs that do not have sensors connected to them When connecting a sensor to an input remove the corresponding yellow wire NOTE Moisture sensor and security keypad are normally open Do not short circuit them Central Unit The central unit should be installed in a protected area No intruder should get to the central unit past the magnetic door switch or without the motion sensor being able to detect the trespasser You must have an access to the central unit if you intend to use door security at night The signal light on the security keypad tells the current operating mode is monitoring on or off Drill holes for the cables on the wall Leave at least 30 cm of surplus length to the cables to make installation easier Push surplus cable back inside the wall after you have connected the wires Fasten the central unit on the wall with three screws included in the package Alternatively you can run the cables on the wall surfac
5. Tape the sensor to the floor Hide the excess of the cable Connect the moisture sensor to the Water connector as depicted in the separate wiring diagram 3 12 Motion Sensor Motion sensor should be installed in the living area where it has the best coverage for sensing movement Do not install motion sensor in entrance hall if security keypad is in the same space The user must be able to come in and switch monitoring off from the security keypad without activating the motion sensor INSTALLATION 9 Detach the cover of the motion sensor by opening the screw at the bottom Connect the motion sensor to the central unit as depicted in the separate wiring diagram It is recommended that you make the following adjustments to the motion sensor Turn the red screw counter clockwise to 11 o clock Change the Pet jumper to 25kg Change the Pulse jumper to place 2 The motion sensor works best with these settings in domestic environment By turning the red screw clockwise you can increase sensitivity Attach the motion Hide the surplus of the cable Connect the motion sensor to the IR sensor to a wall near connector as depicted in the separate ceiling wiring diagram 3 13 Smoke Detector The smoke detector should be attached to the ceiling Do not place the detector in a corner or cranny because then it will not detect smoke so easily Note You can connect up to 8 smoke detectors in the fire connector in HCE Open th
6. digit code you just entered Press is for one second after which you will hear a long signal tone Note Setting the user code to 0000 removes the user code altogether Exit programming mode 8 Press Fun and en The security keypad returns to normal user mode Note Go through the aforementioned steps in one succession without interruption otherwise the security keypad will return to user mode automatically after awhile and the user code is not changed 3 15 Heater Relay You can use HCE for controlling heating in your house You can control an individual heater or an entire heating system with HCE Connect the heater to the central unit HEATER relay Note You cannot control heating from your mobile phone if manual control is turned on Important Make sure that max load 230VAC 10A is not exceeded under any circumstances Important When relay is used to steer inductive load for example another contactor connect RC filter or EMC suppression component in parallel to load to stop voltage spikes when contactor releases Voltage spike may break the relay 3 16 EXT Relay There is a second relay in HCE EXT and its use can be selected freely You can also set this relay to auto mode when it follows device s operating mode If monitoring is on ALARM ON the relay pulls and when monitoring is off ALARM OFF the relay releases This allows you to easily switch off electricity and close water pipe
7. Hide the surplus of the cable Connect the temperature sensor area where you want to measure to the Temp1 connector as temperature depicted in the separate wiring diagram 3 7 Outdoor Temperature Sensor Remember not to place the temperature sensor in direct sunlight Put the temperature sensor outside Hide the surplus of the cable Connect the temperature sensor to the Temp2 connector as depicted in the separate wiring diagram INSTALLATION 7 3 8 Water Temperature Sensor Slide the temperature sensor in the Hide the surplus of the cable Connect the temperature sensor to casing pipe the Temp3 connector as depicted in the separate wiring diagram This sensor can be used for measuring other temperatures besides water and it can be named to describe its usage better see User s Manual 3 9 Siren Install the siren in a such a place where it can be heard Note If a different siren for example an outdoor siren with bigger current consumption is connected to HCE you must use a 12V output relay in between The current consumption of the coil of the relay must not exceed 300mA 12VDC Fasten the siren with the Connect the siren to the Siren screws included in the connector as depicted in the separate package wiring diagram Notice polarity black and red wires 3 10 Magnetic Door Switches Connect magnetic door switches in series as shown in the separate wiring diagram Install them in doors
8. SIM card that will remain in the central unit after the installation is complete If a camera is installed you should make sure that MMS messages messages that contain pictures can be sent from the subscription Some operators require that the service is activated before it can be used You can activate MMS by inserting the SIM card in an MMS compatible phone and sending an activation message to your operator Please consult your telecommunications operator for more information Before inserting the SIM card in HouseControl make sure that you indeed can send MMS messages with that SIM card by testing it with your mobile phone Use an unlisted phone number in your HouseControl so that it is not publicly available However make sure that the HouseControl s phone number is displayed on the screen of your mobile phone when it calls you i e HouseControl s phone number is sent with the call and is not hidden Required Tools You will need the following tools e Side cutters for cables e Pointed pliers to help you connect wires to connectors e Electrical drill and drill bits of various sizes e Screwdriver PREPARATION 2 2 Package Contents Central unit package Battery backup unit package Temperature sensors Battery Check the package contents Central unit Moisture sensor Magnetic door switch flush mounting 2 temperature sensors Siren Motion sensor Smoke detector Battery backup unit
9. TELEMIC HouseControl 0006000000 INSTALLATION MANUAL HOME ENERGY SAVINGS REMOTE CAMERA INTERNET USER INTERFACE TEMPERATURE ALARMS BURGLARY PROTECTION DOOR SECURITY FIRE SAFETY SECURITY KEYPAD WITH PROXIMITY TAGS PREVENTION OF WATER DAMAGES WIRELESS EXTENSIONS Installation Certificate This certificate states that Telemic Oy s HouseControl remote control and alarm system has been installed in the real estate mentioned below Property holder holder of real estate Location of the real estate Real estate Alarm system type Central unit s serial number SIM card phone number Smoke detector model Motion sensor model Magnetic door switches Remote camera Security keypad Siren Installed by We assure that the alarm system was installed in accordance with the manufacturer s instructions thatthe alarm system has been tested and it works as documented thatthe end user has received guidance as to how to use the alarm system Location and date Installed by Signature This form needs to be filled and signed in order to apply for possible refund from your insurance company and before contacting product support 1 u gt Io jp Bleu Ale E E A A 2 2 S PREPARATION 2 2 1 RESUIREBATOOLS A A nen De Rh Ge kuis en en 2 2 2 PACKAGE CONTEN
10. TS 0cc ccececeeeececeeceeeeueecsuueesaeeseaueceaueesaeeesaaseeaueesaueeeausesausesaueesaesesasesaaeea 3 2 3 ACCESSORIES rue A n tat 3 3 INSTALLATION 2 4 3 1 OPENING UNIT S COVER 4 3 2 AGEFFROMINSIDE lt aaa 4 3 3 CONNECTORS ee er a ee 4 3 4 CENTRACUNIT ee A Eee 5 3 5 REMOTE sinnet beer A cw 6 3 6 INDOOR TEMPERATURE SENSOR c0ececeececeececeececuceceucecuucecueseceaseeasecaeseeaeseuaesesaeeesaneenanes 6 3 7 OUTDOOR TEMPERATURE SENSOR 6 3 8 WATER TEMPERATURE SENSOR susosreserosseorsesrrosreorseorssrrrss ers rss rss rss KASSE SSE RARE RSKR SRS SDR SSR SSR 7 3 9 SIREN HD FDR AE 7 3 10 MAGNETIC DOOR SWITCHES sts sah eaa Mau sa sekaan del talados 7 3 11 MOISTURE SENSOR Het LSS Se 8 3 12 MOTION SENSOR 8 3 13 SMOKE DETECTOR ra a a De a a es iia 9 3 14 SECURITY KEYPAD Ss a a re 10 3 15 HIEATERRELAY Ar Set et ed a a e Ka hol 11 3 16 EXT iaa netter er et 11 3 17 POWER SUPPLY AND BATTERY BACKUP UNIT susuamsessressesrresrrosseorsesrres reor rr r 12 3 18 SIM CARD sa fob tel e dol a details 12 3 19 VVIRELESSIEXTENSION ah bon ada 13 4 SETUP 5 2 aa asda aaah a
11. and windows that are most usually left open by accident This prevents burglars from getting in but also prevents the house from cooling down in the winter because of an open back door Connect the installation cable to the switch as Install the parts C and B so that they are no depicted in the wiring diagram Use cover D more than 5mm apart from each other Attach to protect the screw connectors part C to a wall door frame and part B to the door by using screws and two sided tape 8 HouseControl E Installation Manual i o Hide the excess of the cable Connect the installation cable to the Door connector as depicted in the separate wiring diagram Drill a hole in the door frame for flush mounting Push the switch in the hole with your hands Note Do not use hammer Alarm is not activated immediately when the door is opened The user must have some time to cancel the alarm from the security keypad when coming in see User s Manual Note Install the switch on the opposite side of the hinges 3 11 Moisture Sensor Moisture sensors are available as accessories Install the sensor under a bypass manifold or a dishwasher If there is a leakage in the water pipe water will flow in the casing pipe and come out near the bypass manifold and eventually end up in the floor drain By placing the moisture sensor under the bypass manifold you can detect leakages easily
12. e central unit Switch power ON and leave the cover open Wait 30 seconds for the HCE to start up Power switch Picture 1 Opening the cover location of the power switch and the SIM card slot Wait 30 seconds after inserting the SIM card and powering up the unit HCE goes into programming mode and the unit s status light starts blinking If the light does not blink make sure the PIN code SETUP AND TESTING 13 request is disabled from the SIM card the GSM connection has been opened by your operator the GSM signal strength is sufficient in the area and that the SIM card was placed properly in the SIM card slot you will hear a click when it is locked You can ask the GSM signal strength from the device when SIM card is in the device and power is switched on green lights blink and cover is open the device is in programming mode Send message containing only a question mark to your HCE The signal strength should be at least 10 for text messages and 15 for multimedia messages although 20 or more would be better Use an external antenna or install the central unit in a different place if needed 3 19 Wireless extension You can use wireless components with HCE if you have an extension module available as an accessory The extension comes with its own installation manual To start using wireless extension send the following message to HCE no wireless smoke detector WIRELESS BASIC If you have a wireless smoke de
13. e cover cerefully by using a Connect the installation cable to Place a battery in the detector The screwdriver the smoke detector as depicted battery is used only when power in the separate wiring diagram supply from HCE is cut off for some reason Hide the surplus of the cable Connect the smoke detector to the Fire connector as depicted in the separate wiring diagram 10 HouseControl E Installation Manual 3 14 Security Keypad A security keypad is available as an accessory Install the security keypad in the entrance hall in a place where it can be used easily The operating mode is monitoring on or off is displayed by the signal light on the security keypad Make sure the signal light is not visible from outside q E a kin U d Connect the RJ connector to the Attach the security keypad to a wall security keypad in entrance hall F Hide the excess of the cable Connect the security keypad to the GA and Ind1 connectors as depicted in the separate wiring diagram Note Because the key reader on the security keypad uses radio frequencies you should avoid placing it near cables or devices that cause electromagnetic fields contactors Security keypad is preprogrammed in such way that nine keys can be used for changing the operating mode alarm on off Installers key cannot be used for this purpose Operating mode can also be changed by using a secret code The codes are attached to the installer s key
14. e if you wish to avoid drilling holes If this is the case open the indentations on the side of the unit for the cables Note Metal casing so called Faraday cage weakens the GSM signal If the device is installed in a metal case for example an electrical cabinet you need to place antenna outside the cabinet external antenna is available as an accessory Note Some other materials also weaken the GSM signal especially walls that contain metal framing 6 HouseControl E Installation Manual 3 5 Remote Camera You can connect Telemic Oy s remote camera to your HCE When choosing a location for the remote camera it is important to respect privacy and know the law in your country HouseControl can take a picture automatically when motion sensor detects movement Mount the camera Remove the Coil the surplus length of the Connect the remote camera to the lens cover cable and hide it central unit as depicted in the separate wiring diagram lower miniDin connector You can adjust the direction of the camera by loosening the screw at the bottom 3 6 Indoor Temperature Sensor Place the indoor temperature sensor in the living area in an unnoticeable place Run the cable behind a baseboard to the HCE Note Do not leave sensors uninstalled Shorten cables as needed and install temp1 and temp2 sensors inside HCE so that there will be no unnecessary temperature alarms Place the temperature sensor inthe
15. ing You can test the system by going through the following steps after you have selected language and put the cover back on the central unit You can change the unit s operating mode is monitoring on or off by using text message commands or by using the security keypad and proximity key 14 HouseControl E Installation Manual The operating mode does not change immediately if you use security keypad There is a 30 second delay when switching monitoring off and a 45 second delay when switching monitoring on There are no delays if you use text messages ALARM ON and ALARM OFF except the time it takes the message to travel in the GSM network When testing the system you can silence the siren by using a proximity key the operating mode does not change if alarm is active 1 10 11 Magnetic door switches Send ALARM ON message to the unit and trigger an alarm by opening a door or a window with magnetic door switches Wait until you receive an alarm text message Send ALARM OFF to the unit to clear alarms Moisture sensor Drop some water on the sensor so that it alarms Wait until you receive an alarm message Send ALARM OFF to the unit to clear alarms Motion sensor Send ALARM ON message to the unit and go inside the house so that the motion sensor detects you Wait until you receive an alarm message Send ALARM OFF to the unit to clear alarms Smoke detector Test the detector as instructed by the smoke detector manufactu
16. rer The alarm must be at least 10 seconds long for HCE to react to it Wait until you receive an alarm message Send ALARM OFF to the unit to clear alarms Notice that both sirens the siren in the smoke detector and the siren connected to HCE must go on when there is an alarm Exception if interconnect feature is enabled in the smoke detectors every smoke detector siren should alarm Carbon monoxide detector Test the detector as instructed by the manufacturer Wait until you receive an alarm message Send ALARM OFF to the unit to clear alarms Enabling remote camera Send CAMERA ON message to the unit and then ask report from the unit with command Check that the camera is enabled CAMERA ON from the report Taking pictures with remote camera You must tell HouseControl the multimedia settings MMS of the particular GSM subscription before it can send pictures In addition some operators may require an explicit activation of these settings If this is the case place the SIM card in an MMS capable phone and consult your operator for further instructions You will usually find the multimedia settings and activation instructions from telecommunications operators web pages Command Example command MMSAPN Access point name MMSAPN MMSURL URL address MMSURL http xxx xx xx MMSIP Gateway IP address MMSIP xx xx xx xx MMSPORT Port number MMSPORT xxxx MMSUSERNAME User name MMSUSERNAME MMSPASSWORD Password MMSPASSWORD
17. ssa asda rr 13 4 1 TESTING Rn eae E 13 1 2 1 HouseControl E Installation Manual INTRODUCTION This manual describes the installation of HouseControl remote control and alarm system The instructions in this manual can be applied to many kinds of houses It is important that you plan carefully how you are going to install HouseControl For example to achieve finished look make sure the cables run inside the walls and other structures This requires that you have a plan for where you are going to install smoke detectors motion sensors and other accessories as you are building your house You can connect up to three temperature sensors a siren a magnetic door switch a moisture sensor a smoke detector a motion sensor a security keypad a remote camera and a control panel to the central unit You can connect several motion sensors magnetic door switches smoke detectors and moisture sensors to one input Always connect the sensors according to the separate wiring diagram The central unit contains two relay outputs 230VAC AC 6A and 10A The 10A relay can be controlled thermostatically PREPARATION You need a GSM subscription and a SIM card from a telecommunications operator for testing and using HouseControl You must disable the PIN code request from the SIM card before inserting the card in the central unit It is recommended that testing is conducted with the same
18. tector in the system use command WIRELESS FULL SETUP AND TESTING Now it is time for post installation setup and testing See the Trouble Shooting chapter in the User s Manual if you encounter any problems 1 Make sure there is a SIM card in the central unit Switch power ON and leave the cover open Wait 30 seconds for the HCE to start up The unit s status light starts blinking as it goes into programming mode If the light does not blink make sure the PIN code request is disabled from the SIM card the GSM connection has been opened by your operator the GSM signal strength is sufficient in the area and that the SIM card was placed properly in the SIM card slot Leave the cover open 2 Make a test call to the unit to make sure it is connected to the GSM network If the call is connected GSM connection is open and everything is ok HCE answers with three beeps and disconnects the call 3 Select language with command LANG xx where xx is the language of your choice see list of available languages from the User s Manual This command initializes the unit and sets your phone number in the first location of the phone directory The HCE can be used only from this phone number at this point More users can be added later see User s Manual LANG EN LANG EN Language EN English P1 35844nnnn Your phone number in directory location one 4 Put the cover back on and fasten it with screws Start testing 4 1 Test
19. when leaving home EXT relay can also be used as a LEAKGUARD When moisture sensor detects moisture the EXT relay pulls The relay releases when leakguard is disabled or reset When leakguard is in use you cannot set the relay on or off with EXT command 12 HouseControl E Installation Manual Connect the device to the EXT relay You can use the relay for example for controlling magnetic valve in water pipe and prevent water damages Important Make sure that max load 230VAC 6A is not exceeded under any circumstances Important When relay is used to steer inductive load for example another contactor connect RC filter or EMC suppression component in parallel to load to stop voltage spikes when contactor releases Voltage spike may break the relay 3 17 Power Supply and Battery Backup Unit 1 Connect the cable from the battery backup unit to the 12V and GND connectors as depicted in the separate wiring diagram 2 Connect the battery 3 Attach the battery to the casing with two sided tape 4 Connect the mains cable Make sure the HCE works even if you detach the mains cable from the wall outlet This proves that the battery has been connected properly and the 4A fuse is ok 3 18 SIM Card First disable the PIN code request from the SIM card Make sure the power is switched off from the HCE power switch is OFF see picture below and insert the SIM card in the SIM card slot in the bottom right corner of th
Download Pdf Manuals
Related Search