INFRARED QUARTZ HEATER
Contents
1. the temperature display on another thermostat like the one mounted to your wall or a purchased external thermostat This is because the temperature sensor on the heater reads the temperature directly around the heater With the heater near the cold floor and heat rising any readings on elevated or external thermostats will differ in readings on the heater The best way to operate your heater is to set the unit on High and dial up to a temperature that feels comfortable to you Then leave it at that temperature regardless of the mismatch The heater will cycle off when the set temperature is met or exceeded slightly lifeszpro PREPARATION Place the heater on a firm level surface and plug into a grounded 120 V 60 Hz power outlet Only operate heater in upright position Please note that infrared heaters do not heat like a traditional space heater You should not expect infrared heaters to blow hot air like a traditional space heater Infrared heaters heat objects not air Infrared heaters are intended to supplement an already heated insulated room Square footage specifications assume a single enclosed room not an entire home Infrared heaters do not heat through walls floors and are not intended to replace a main heat source Infrared heat can take at least 24 hours to warm a room but operate much more efficiently to maintain the desired temperature Infrared heaters will not work well in uninsulated unheated spaces like screened in porc2. MAREE oh Re ee ea 13 lifezpro PACKAGE CONTENTS E of Jo Goaeees Geeeeen Geceece ennenen fenan Genesee Ganeees Gassees Eeee esse EE BERE EEEEEEB CD Front View Rear View PART DESCRIPTION QUANTITY A Infrared Heater 1 B Master Power Switch pre assembled to Infrared Heater A 1 C Control Panel pre assembled to Infrared Heater A 1 D Filter Cover pre assembled to Infrared Heater A 1 lifezpro SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble operate or install the product IMPORTANT SAFETY INSTRUCTIONS A WARNING POTENTIAL ELECTRICAL HAZARD IF NOT ADHERED TO When using electrical appliances basic precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following This heater must be plugged into a 120 V 15 amp or more circuit of its own Do not plug anything else into the same circuit If unsure if your home meets this specification consult a certified electrician prior to use Risk of fire overh
3. cidental or consequential costs expense or damages without irrefutable foundations Under no circumstances shall the manufacturer or any of its representatives be held liable for injury to any person or damage to any property however arising Any implied warranty shall have duration equal of the applicable warranty stated above Specifications are subject to change without notice or obligation This limited warranty gives the original purchaser specific legal rights Other rights may vary from state to state lifegzpro 12 REPLACEMENT PARTS LIST For replacement parts call our technical support department at 1 866 484 2066 8 a m 5 p m CST Monday Friday PART DESCRIPTION PART A Mode Switch MO SW B Fan FAN213 C Thermostat THER SW D Tip Over Switch TIPSW O o E Limit Switch LIMIT110 i O o 7 F Infrared Tube QUAR R21 G Temp Sensor SENSOR O H Power Switch MAINSW S a Ri o macs PLEASE REMEMBER TO REGISTER YOUR WARRANTY Registration lifecorpproducts com Printed in China lifepro is a registered trademark of lifecorp products lifezpro 13
4. eating malfunction property damage injury or even death may result if not adhered to Connect to a properly grounded 3 prong outlet only Do not connect the heater to extension cords surge protectors timers direct breakers or an outlet with other appliances connected to the same outlet Risk of fire overheating malfunction property damage injury or even death may result if not adhered to This heater is hot when in use To avoid burns do not let bare skin touch hot surfaces Use handles certain models or wheels to move this heater Keep combustible materials such as furniture pillows bedding papers clothes and curtains at least 3 ft 0 9 m from the front of the heater and keep them away from the sides and rear of the heater Extreme caution is necessary when any heater is used by or near children invalids pets or when the heater is left operating unattended Always unplug the heater when not in use Do not operate any heater with a damaged cord or plug or after the heater malfunctions has been dropped or damaged in any manner Contact the manufacturer for resolution options Do not use outdoors Exposure to outdoor elements such as rain snow sun wind or extreme temperatures may cause the heater to become a safety hazard This heater is not intended for use in bathrooms laundry areas and similar indoor locations nor any locations that use GFCI outlets Never place the heater where it may fall into a bathtub or o
5. ertified electrician A WARNING Risk of fire damage to property or injury may result if requirements are not met Q Why does my heater s fan continue to run after the set temperature is reached or the power is turned off A This is normal The heater s fan will continue to run even after the heater automatically cycles down The fan continues to run so that every last bit of heat is blown out of the heat chamber while allowing the unit to continue filtering your air Once the internal box components cool completely the fan should then shut off on its own In this case allow a few minutes after the heat cycles off with power on The fan will shut off faster when the power is turned off Q My heater s power cord gets warm My cord is showing signs of heat or melting at the outlet Is this normal A Awarm power cord is normal These power cords are rated safe for up to 105 C 221 F by the UL CSA or ETL The exception is if you detect heat smoke or signs of melting at the contact point of the wall outlet it may be due to loose or worn wall contacts or arcing Please stop using the heater immediately contact warranty support for a replacement power cord and have a certified electrician replace the wall outlet as soon as possible Q The temperature on my heater does not match the temperature display on my wall or external thermostat Why A This is completely normal The temperature display on your heater may vary from
6. h the highest quality materials and is warranted to be free from defects in materials and workmanship at the time of purchase This limited warranty applies to products manufactured or distributed by the manufacturer are delivered in the continental United States and extends to the original purchaser or gift recipient This warranty becomes valid at the time of purchase and terminates either by the specified time frame listed above and or owner transfer Any refunds or monetary compensations must be claimed through the place of purchase retailer and not through the manufacturer Any extended warranties warranties that cover above and beyond this manufacturer warranty that are sold through a retailer or third party are not directly correlated with this products limited warranty and may be redirected to said retailer or third party for coverage This warranty extends through the manufacturer of the product and covers functional parts only Cosmetics are not covered unless unequivocally determined it is a workmanship defect Shipping damage should be addressed with the shipping company retailer or place of purchase not the manufacturer unless the manufacturer was the direct shipper The manufacturer s sole obligation under this warranty shall be limited to furnishing the original purchaser replacement parts for units deemed repairable by the supplier s warranty department The purchaser is responsible for insuring any parts shipped or retur
7. hes RV s garages unheated basements etc TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION The heater does not 1 The power cord is not plugged in 1 Plug the power cord into an electrical outlet turn on 2 The electricity at the main fuse boxis 2 Check the electricity at the main fuse box not working 3 Increase the thermostat temperature on the 3 The thermostat on the heater is set heater for a higher heat setting lower than the room temperature There is no heat 1 The unit is in Fan Only mode 1 Turn the MODE dial to one of the two heat 2 The temperature needs to be increased settings 1 1 000 W or 2 1 500 W on the heater 2 Turn the THERMOSTAT dial clockwise until you hear a click If the unit shuts down There was a power outage 1 Turn MODE to OFF and Thermostat to HI 2 The unit overheats 2 Unplug the unit and wait 5 10 minutes then plug in and turn MODE to ON lifes2pro CONTROL PANEL DESCRIPTION 1 Thermostat Dial Increases and decreases desired temperature 2 Digital Display Readout of ambient room temperature 3 Mode Dial Toggles between Off Fan Low High Modes lifezpro OPERATING INSTRUCTIONS 1 Turn the heater on or off by turning the MODE dial on the control panel C to the 1 position Once the power is off the heating elements and fan will stop working This is a norma
8. ked questions on the next few pages prior to using your heater Q My heater emits a strange odor when first open the box and when turn the heater on for the first time Why is this happening A This is normal This heater is treated with a special heat safe resistant coating This odor will sometimes be present when the box is opened When the coating is exposed to heat it produces this particular odor during the first few hours of operation This will dissipate after the break in period If you are sensitive to odors you may want to pre burn the unit in a garage with the door open until the initial odor dissipates Q If my heater runs on approximately 1 500 watts how many BTUs is that Is that a lot of heat A At 1 500 watts your heater will produce approximately 5 100 BTUs This heater is intended to be used as supplemental heat in areas most needed It may take several minutes to several hours to heat your area depending on various factors Q Can the heating elements be replaced A Replacement heating elements can be obtained from the manufacturer All parts may be purchased through the manufacturer if your product is out of warranty If you feel that the elements are definitely faulty right out of the box contact technical support A representative can then direct you to the next step Q Once plug the unit in and turn it on how long will it take to heat my room A The heating process in the heater begins immediately
9. l function 2 Select a heat setting by turning the MODE dial on the control panel C to the 1 2 or fan only position Power for setting 1 mode is 1 000 W setting 2 mode is 1 500 W FAN mode is an cooling function When FAN mode is chosen the heater will operate at approximately 15 W 3 Set the thermostat by turning the THERMOSTAT dial clockwise or counter clockwise on the control panel C You can set the temperature on the heater anywhere between and of the thermostat Turn the THERMOSTAT dial towards or to get a lower or higher desired temperature Once you have chosen the desired temperature the heater will cycle on and off to maintain the desired room temperature For continuous heat set the thermostat towards 4 The digital display will show ambient room temperature at all times 10 CARE AND MAINTENANCE A WARNING Before performing any maintenance task unplug the unit and allow it to cool completely 1 To keep the heater clean clean the outer shell with a soft damp cloth Use a mild detergent if necessary After cleaning dry the unit with a soft cloth CAUTION DO NOT let liquid enter the heater 2 DO NOT use alcohol gasoline abrasive powders furniture polish or rough brushes to clean the heater This may cause damage or deterioration to the surface of the heater 3 DO NOT immerse the heater in water 4 Wait until the unit is completely dry before use 5 If you
10. lifegzpro INFRARED QUARTZ HEATER MODEL LS21 2W BPIQT lifepro is a registered trademark of lifecorp products All Rights Reserved PA JUULI l ATTACH YOUR RECEIPT HERE c ell us Intertek Purchase Date Serial Number located on back of unit 1 866 484 2066 8 00 a m 5 p m CST Monday Friday or www lifecorpproducts com Ey Questions problems missing parts Contact technical support department at Please have your model and serial number ready m life2pro TABLE OF CONTENTS Package CONS 0 narra o AE 3 Safety NOMAN ss acd enana i a a A a a 5508 o DE a a EA E EE E Ea 4 Frequently Asked Questions cv cta cache wee A AA RARA eed le aw 6 Preparation A o eat EE ee i ote os Se ee we ee as oe te ae 8 a s 2 6 2 3 05 gee eee hoe eae oes 4 43288 2 685222 ne bee eset ee Betas Gen 8 Control Panel 2 evade ted cee heeds dees cee eed ee eee ae lous Seabees de 9 Operating Instructions n n anaana eE AAA 10 Cale and Maintenant h2 lt 4e0464544 355008 4 62066066055454 5566 oe ais os Be 11 One Year Limited Warranty lt lt lt taeda sands eed AAA A eed cee eee ae tes 12 Replacement Parts List cor cccnateken dle dw ook cee
11. ned if desired The purchaser is responsible to prepay any shipping charges both ways including but not limited to taxes and duties All exchanged parts and products replaced under this warranty will become the property of manufacturer The manufacturer reserves the right to change manufacturers of replacement parts or products for use in order to cover any existing warranty The purchaser may be asked to provide the supplier with proof of purchase documents including the date of purchase if requested Any evidence of alteration erasing or forgery of proof of purchase documents will be just cause to VOID this limited warranty Products in which the serial number has been defaced or removed are not eligible for warranty coverage This warranty does not apply if the unit has been subject to negligence fabrication misuse abuse or repairs alteration by non manufacturer authorized personnel inappropriate installations or any case beyond the control of the manufacturer Examples of warranty invalidation may also include but are not limited to e Use of lacquer or paints in and around the heaters e Heater placed on non approved surfaces e Electrical requirement deficiencies 15 20 amp dedicated outlet e Use on extension cords timers surge protectors GFCI e Outdoor applications e Normal wear tear weathering e Pet consumer accidents The manufacturer shall not be liable for any loss due to use or misuse of the heater or other in
12. peration turn on the heater using the supplied remote control or the control panel on the heater Overheat Safety Feature This heater is equipped with an overheat safety feature When the internal components of the heater reach a certain temperature that could cause overheating or possible fire the heater will automatically shut off Ay WARNING This heater has a voltage rating of 120 volts The cord has a three blade grounding type plug An adapter is available for connecting three blade grounding type plugs to two slot receptacles The grounding lug extending from the adapter Grounding Pin must be connected to a permanent ground such as a properly grounded outlet box The adapter should not be used if a three slot grounded receptacle is available DO NOT DEFEAT THE SAFETY PURPOSE OF THE GROUNDED PLUG Metal Screw A Cover of Grounded Outlet Box A O o Grounding Means Grounding Pin A WARNING It is normal for the power cord to feel warm to the touch However a loose fit between the outlet and the plug may cause overheating of the plug If this occurs try inserting the plug into a different outlet Contact a qualified electrician to inspect the original outlet for damage Specifications Voltage Rating 120 V 60 Hz Power Consumption 1 000 W 1 500 W Unit Size 8 4 in W x 11 5 in D x 20 1 in H Unit Weight 14 2 lbs lifes2pro FREQUENTLY ASKED QUESTIONS Please review these frequently as
13. ther water receptacles Do not run the cord under carpet Do not cover the cord with throw rugs runners or similar coverings Arrange the cord away from traffic areas and where it will not be tripped over The heater must be plugged into a wall outlet that is a dedicated circuit with a minimum 15 amp rating on that individual circuit To disconnect the heater first turn the power button to the OFF position and then remove the plug from the wall outlet Do not allow foreign objects to enter or block any ventilation or exhaust opening as this may cause electric shock fire or damage the heater Allow at least 3 ft of unobstructed space to the front and rear of the heater to allow for maximum heat air and ventilation flow A heater has hot and arcing or sparking parts inside Do not use it in areas where gasoline paint or flammable liquids are used or stored nor use flammable solvents to clean the heater Keep the heater dry at all times Use this heater only as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons Do not use abrasive solvents to clean the heater as it may cause T SAFETY INFORMATION Tip Over Safety Feature This heater is equipped with a tip over safety feature Once the heater is tipped over an internal switch will automatically shut the heater off Once the heater is restored to an upright position the heater will reset To continue o
14. upon powering on and setting the desired temperature above the ambient temperature A noticeable change in the ambient temperature of the room will vary due to variables such as the location of the heater in the home floor plan and size of the room how well the room is insulated how many doors windows how much bare concrete acts as a heat sink with any type of heating the opening and closing of an exterior door long hallways high ceilings etc Customers with smaller rooms experience quick heat changes Rooms with larger and open floor plans can expect up to 24 hours to completely heat up Q do not have a grounded outlet Can use a 2 prong power strip or remove the ground prong from the cord A NO If you do not have a grounded outlet contact a certified electrician for advice Removing or altering any part of the heater s original design or intent including the power cord will void the warranty and make you liable for any unexpected or hazardous results lifezpro FREQUENTLY ASKED QUESTIONS Q Can use more than one heater at a time Can use the heater and another appliance at the same time A Yes but make sure they are not plugged into the same circuit Each heater requires its own minimum 15 amp circuit with no other items plugged into that circuit or outlet This is because heaters are considered appliances and draw out high amperage If you are unsure whether your circuit meets these requirements verify with a c
15. will not be using the heater for a while take the batteries out of the remote control and store for future use 6 Store the heater in a cool dry location when not in use To prevent dust and dirt build up use the original packaging to repack the unit CLEANING THE AIR FILTER 1 Clean the air filter 2 after three months or if it appears to be blocking airflow With the heater unplugged remove the filter guard holding the filter in place 1 as illustrated below Clean all parts of the filter assembly and allow parts to completely dry 2 Reassemble and reinstall the filter guard 1 A WARNING Do not use the heater without the filter assembly in place ONE YEAR LIMITED WARRANTY The manufacturer warrants this heater against defects in materials and workmanship on functional parts for a period of 1 year from the original date of purchase Your sales receipt showing the date of purchase of the product is your proof of purchase Keep it in a safe place for future reference This product is made wit
Download Pdf Manuals
Related Search