Installation Guide/User manual
Contents
1. Navigation radios in 5 Series 7 Series and X5 models Radio specific text field configuration should be performed during installation Please refer to interface setting DISC 5 section on page 19 Supported iPod models and firmware version requirements Model O Firmware OS Version Model O Firmware OS Version 1G nano 1 3 1 160 GB classic iPod 5G 1 3 5G nano 2G nano 4 1 3 3G touch iPod classic 1 1 2 iPhone 4 3G nano A413 iPhone 4S iPod touch iOS 3 1 3 4G touch iPhone iOS 3 1 3 6G nano iPhone 3G iOS 4 2 1 4G nano 1 0 4 120 GB classic 2 0 1 2G touch iOS 4 2 1 iPhone 3GS iOS 5 10 Attention Installer Please read the following DICE Electronics strongly recommends that the unit be installed in an easily accessible place DO NOT PLACE IT BEHIND THE RADIO AND DO NOT HIDE UNDER CARPET Whether the unit is professionally or self installed put the module where you the end user can get to it easily in the future Have the installer show you where the interface module is installed Installing the module behind the radio will make it difficult to e Add possible future upgrades changing software adding new features improving operation e Access the AUX input on the module to attach any audio device Access the DIP switches located on the module e Remove the unit in case of failure MAKE SURE THAT THE MODULE IS IN AN ACCESSIBLE PLACE 11 Connection diagram CD changer cab2. caution when removing trim pieces as they may break The module should be placed in an accessible location such as the glove box consoles under the front seats or in some cases in the trunk to allow iPod SIRIUS AUX cables to be connected The module firmware may need to be updated periodically and must be removed from the vehicle and connected to a computer to apply the update 1 Disconnect both battery terminals These cables must be disconnected during installation to ensure proper initialization of the module when it is connected This step is REQUIRED for proper operation of the module 2 Access the CD changer cable The location of this cable varies by BMW model for connector locations see page 13 3 If the vehicle you are performing the installation on has DSP refer to page 12 and then proceed to step 5 Locate both the 3 pin amp 6 pin connectors If the vehicle has a factory CD changer installed the 3 pin amp 6 pin cables will be connected to it and will need to be disconnected If there is nota CD changer installed the cables will be bundled and may be tucked away behind carpeting Some vehicles will have the CD changer wiring in a protective sheath which may make it more difficult to locate Non US models may not be pre wired for a CD changer and require an additional harness from BMW to be connected 15 4 Connect both 3 pin and 6 pin cables to the BMW Interface Harness ATTENTION There are two 3 pin connectors presente
3. humidity or shock Keep the unit and iPod iPhone away from fluids Keep away from children Interface components may contain small parts can be broken or disassembled and components may become loose from vibration and heat Small components and packaging materials may be a choking hazard when handled by children Congratulations on your purchase Thank you for purchasing this integration kit Please review this booklet before operating the unit This interface was designed and manufactured to seamlessly integrate with your vehicle s factory audio system Product registration We recommend registering your DICE product so you can receive news about important firmware updates and have unlimited access to our online support system To register your DICE product please complete the following steps 1 Visit http www register diceelectronics com 2 Look up and save the serial number of the product 3 Complete the product registration form 4 Submit the form 5 Save the registration support warranty sheet in a safe place for future reference If you are unable to complete the registration via internet please call DICE Electronics at 1 888 342 3999 Prior to installation make sure the module s firmware is up to date to ensure compatibility with the latest features and enhancements Please refer to page 33 to update firmware 6 MediaBridge kit content Poice MediaBridge module User manual MediaBridge connect
4. not stopped To resume playback of your iPod music library stop Livio playback by tapping on the screen below the Livio Radio logo An icon representing stop will show on the main Livio screen Press the home button to send the application to the background Other apps may need to be terminated manually Please see next page A few seconds after this the iPod music playback application will reinitialize itself and become active again if the iPod was locked when it was connected to the kit This is indicated by an Accessory Connected message being shown when the iPod icon is tapped If the iPod was in unlocked state when it was connected to the kit press the play button on the iPod application Text Display from the Internet Radio App Text that scrolls across the radio s screen is associated with the stream shown on the radio and displays current song or station information Stream must be playing before information on the display is updated 32 Terminate kill the App If you need to terminate kill the app please follow the steps below 1 Double tap on the home button of the iPhone to bring up the list of running apps If you don t see the app s icon right away swipe the screen left or right to locate it Note If you do not see such task bar but rather a music control popup then you have an iOS device that does not support background run of apps therefore this section is not applicable to you 2 Press and hold the
5. other incurred damages resulting from product defects Any expenses in the removal and reinstallation of products are not covered by this warranty PLEASE NOTE International customers requiring a product replacement please contact the dealer your product was purchased from Installation notes Installed by Installed date Other notes Illustration 39 pOICE ELECTRONICS BMW Mini Cooper compatible integration for iPod iPhone Internet Apps Bluetooth SIRIUS and AUX www diceelectronics com DICE MB BMW 0312
6. source mode see page 24 On Mini Navigation radios the RND button is used to toggle be tween Menu and Text modes Text Mode RND enabled Dis plays text from the MediaBridge such as Song Artist Playlist titles Menu Mode RND disabled Displays the default Navigation and vehicle menu screens coc 1 TROT D 1 Use DISC buttons 1 6 to change between DISC modes and to recall and store SIRIUS stations MediaBridge SIRIUS source mode Selected source indica tor AM FM CD CDC Used to store stations to Presets 1 5 Icon legends Press button A Press and hold button Oo Turn dial AN Press button repeatedly Controlling the MediaBridge iPod Source Use DISC 1 6 to enter browsing modes SONG PLAYLIST ARTIST ALBUM PODCAST and AUDIO BOOK e Within each mode use the TRACK button to browse the items available Note if the iPod is unlocked radio control will be limited to Songs Playlists and Albums Text display will also be limited to show only current song information CHANGE SONGS DISC 1 4 TRACK gt CHANGE PLAYLIST DISC2 4 TRACK gt CHANGE ARTIST DISC 3 gt 4 TRACK gt CHANGE ALBUM D x 4 gt 4 TRACK gt CHANGE PODCAST DISC5 gt 4 TRACK gt CHANGE AUDIO BOOK DISC6 gt 4 T
7. 0 Operating the MediaBridge from select BMW and Mini radios NOTE 99 01 3 Series and Z3 will require double clicking buttons when text is displayed Illustration showing BMW Business CD Radio o s Selected source indicator AM FM CD CDC cpc 1 Song Artist Album RND TP Press the MODE button to access MediaBridge as the audio source AM F SC MODE amje Use DISC buttons 1 6 to change between DISC modes and to recall and store SIRIUS stations MediaBridge SIRIUS source mode Use RANDOM to turn shuffle songs ON OFF Press RND followed by DISC 1 6 to store a preset while in Sirius mode Press the TRACK buttons to go to the next previous song playlist artist or album de pending on which DISC number is selected Press and hold the TRACK buttons to RW or FFW On some older BMW radios the m button must be engaged to perform the same action Use DISC buttons 1 6 to change between DISC modes and to recall SIRIUS stations Press and hold to store SIRIUS stations MediaBridge SIRIUS source mode Illustration showing BMW 16 9 Navigation radio Song title Selected iPod mode Song Playlist Artist etc Current source iPod Sirius AUX Shows whether Bluetooth enabled phone is paired BT Not paired BT Paired Variou
8. RACK gt 23 24 Controlling the MediaBridge USB memory source Select DISC 1 then use the track buttons to change from song to song e Select DISC 2 6 to browse Folders and use the track buttons to navigate through the folders on your USB flash drive e The MediaBridge unit will recognize the first 8 levels of folders with up to 200 accessible folders within each folder Only the first 1000 files will be read in each folder the rest will be ignored Songs play in the order they were added to the flash drive e Use the Random feature on radio to shuffle all songs on the flash drive This may take a long time to complete if the flash drive is more than 4GB CHANGE SONGS DISC 1 lt 4 TRACK gt CHANGE FOLDER DISC 2 lt 4 TRACK gt CHANGE FOLDER DISC 3 lt 4 TRACK gt CHANGE FOLDER DISC 4 lt 4 TRACK gt CHANGE FOLDER rs 5 lt 4 TRACK gt CHANGE FOLDER DISC 6 lt TRACK gt 25 Controlling the MediaBridge SIRIUS source The MediaBridge integration kit features SIRIUS connectivity requires additional tuner Use the TRACK buttons or jog DIAL to browse between subscribed channels To store a subscribed channel to memory e Single line radio Tune to desired station Press RANDOM button and select which DISC button preset 1 6 to save to Press RANDOM button once more to store the station e Navigation radios Tune to desired statio
9. SNIN MEDIABRIDGE MULTIMEDIA INTEGRATION KIT for select BMW Mini Cooper vehicles Installation Guide User manual Copyrights and Trademarks Copyright 2012 DICE Electronics LLC The DICE Electronics logo is trademarks of DICE Electronics LLC iPod and iPhone are trademarks of Apple Inc All Trademarks and Logos are the property of their respective owners All rights reserved Printed in the U S A Table of Contents Warning and Safety sc stcccccsssgecsccesceedeeuseteasedeececestenesbened 4 Product registration cccsccescceeseeseeeeaeeseeeeeneetseeeeees 5 MediaBridge kit content DIP switch overview DIP switch settings for BMW Mini Supported iPod models cc cessceeeeeeeeeeteeeeteeeteeeeeee 9 Note to Installet rece ada Connection diagram Connection diagram for DSP option Factory CD changer cable locations 0 c eeeeee INStAIIAOM TEENE A Geet ae ee eee iPod content browsing Charging iPod locked unlocked settings and features 05 18 BASIC OPERATION m fi 10 Seid heaped recesses iaieee et 19 Operating the MediaBridge unit from select radios 20 Controlling the MediaBridge iPod source ceeee 23 Controlling the MediaBridge USB memory source 24 Controlling the MediaBridge SIRIUS source Bluetooth amp MAT configuration Pairing MediaBridge with cell phone via BT Answering Ma
10. active as shown on the left the iPod iPhone is locked Press the power button to lock the iPhone iPod Touch 19 Basic Operation Accessing MediaBridge as the audio source Much like the radio s AM FM tuner satellite radio or CD audio sources the MediaBridge is integrated to be part of the vehicle s audio system To access the MediaBridge source press the MODE or CD button on the radio Pressing this button repeatedly will cycle through sources present in the vehicle CD gt MediaBridge MediaBridge source selection The MediaBridge adds additional audio sources including iPod SIRIUS Satellite Radio and auxiliary audio input To cycle between these sources use the next previous TRACK buttons within the first 5 seconds of accessing the MediaBridge as the audio source while in DISC 1 This source require additional parts accessories service from DICE and or third parties MediaBridge Interface settings within first 5 seconds of accessing the MediaBridge as the audio source Select DISC 1 to apply settings and resume audio playback Select DISC 3 to change default volume level use track up down to adjust between Min and Max Select DISC 4 to enable disable scrolling text Select DISC 5 to choose between single line display and multiline display modes multiline display mode only available on 16 9 Navigation radio Select DISC 6 to view MediaBridge serial number and firmware version DISC 2 has no settings available 2
11. and is licensed only not sold No warranty explicit or implied is stated Neither DICE Electronics LLC nor any of its agents distributors dealers or vendors shall be liable for damages IN NO EVENT SHALL DICE ELECTRONICS LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT ITS ACCOMPANYING SOFTWARE OR ITS DOCUMENTATION 38 Support and Warranty If you experience any problems or need help please contact you local dealer or call DICE Electronics LLC At 888 342 3999 or visit us at http diceelectronics com product support Products carry a 1 year limited warranty that protects you from defects in material and workmanship of products sold by DICE Electronics or its authorized agents distributors and dealers The warranty period begins the day a product is purchased by the end user Products found to be defective during the warranty period will either be repaired or replaced by DICE Electronics at no charge unless warranty is void Unauthorized attempt of repair or alteration of the product in any way immediately voids this warranty Warranty does not extend to cosmetics or finish A DICE product specialist must determine that a defect is present in the product and issue an RMA Be sure that all wiring is connected as described in the user manual and all related equipment is functioning properly DICE Electronics disclaims any liability for
12. d in the vehicle During installation make sure that the 3 pin connector from the vehicle DOES NOT have a brown wire in the middle The 3 pin connector of the phone pre wiring looks identical to the 3 pin connector of the CD changer pre wiring Locate and use the correct 3 pin cable with the brown wire on the outside Incorrect connection will result in permanent damage to the unit and will not be covered by warranty 3 pin and 6 pin BMW cables Note that in the X3 there may be two 6 pin audio connectors present Connect the harness to the one without the CD label 16 Route the interface cable to the front of the vehicle Fold down rear seats if applicable and route the extension cable through the rear seat bottom cushion Route the remainder of the interface cable ie under the door sill or under the driver s seat to a location where the module can be easily accessed in the future Make sure you have set the DIP switches on the MediaBridge as specified on page 8 Connect the BMW interface cable iPod Dock Cable and SIRIUS Connections if applicable to the MediaBridge module and double check all connections See page 11 and page 12 if the vehicle has DSP for the connection diagram Test the installation Replace any trim carpeting or panels that were removed during installation 17 iPod content browsing A la By default the interface creates a Playlist having a name that is the same 8 a as the name o
13. eams and phone calls aren t audible on the phone but can be resumed by re entering MediaBridge mode Answering I Making a phone call To answer an incoming call press the button that tunes to the next Phone calls interrupt any music track or channel audio that is currently playing on To reject an incoming call or terminate an active call press the but the radio while MediaBridge is the ton that tunes to the previous track or channel selected audio source To make an outgoing call dial on the phone like you would normally Playing music from a cell phone through MediaBridge via Bluetooth 1 Enter Bluetooth mode on MediaBridge 2 Make sure your cell phone is paired with MediaBridge 3 Select and play a song from your cell phone s music player Note Some cell phones require you to manually select the option to play music via A2DP Bluetooth Streaming Song information is shown on the radio display if your phone supports AVRCP1 3 4 Use Track UP DOWN to skip tracks FF RW songs on the AVRCP compatible phone 28 Accessing the auxiliary input CHANGE VOLUME SETTING An auxiliary audio device can be connected to the MediaBridge DISC 1 gt 4 S p unit through it s 1 8 headphone jack CHANGE BASS SETTING DISC 2 gt 4 TRACK gt In AUX mode music is controlled only through the auxiliary audio device CHANGE MID EQ SETTING x DISC 3 gt 4 TRACK gt x Zs e Audio equi
14. ee if iPod charges while connected to computer or iPod does NOT charge wall charger You may need to reset the iPod Music is distorted or sound level is too Make sure all EQ and BASS boost options are turned off on your iPod low with iPod connected Adjustments to the gain setting may be required refer to page 19 Reset the iPod Verify proper connection to iPod interface Check for No audio from iPod source compatibility Older iPod models don t support USB audio and may only operate in Locked mode 35 Problem Solution Ensure the cable connecting the SIRIUS tuner is securely connected to the Sirius tuner can t be selected correct receptacle on the MediaBridge module Refer to page 19 for cycling through MediaBridge audio sources Why does the radio display show The iPod has reached the end of a selection Go ahead and browse for EMPTY STOP and no music plays another selection Verify that the correct button is being pressed to access the interface CD Cannot select the interface or Mode Disconnect the MediaBridge module s power connection for one minute to reset it Reset iPod and make sure the most recent iPod firmware is installed Check vehicle user manual on how steering wheel controls work long presses may toggle alternate function Engine may need to be running on some models Radio steering wheel controls do not operate iPod Why does category read Playback of content s
15. elected on the iPod before it is connected to the PRESELCTD interface continues until new content is selected 36 Problem Solution Why does the message iPod UNLOCKED display on screen When the MediaBridge is playing iPod music in UNLOCKED mode browsing mode information isn t available so the iPod UNLOCKED notification is shown To view information associated with browsing modes ensure the hold button of the iPod is set before connecting it to the MediaBridge Why is the interface not controlling the iPod USB drive What size of USB flash drive should use Please make sure that the USB connection is not loose Make sure that an iPod case is not preventing the dock connector from being fully seated Disconnect and reconnect the device If iPod is not responding please try resetting it USB device must also be FAT16 32 format and contain supported MP3 WMA or AAC content Large capacities are supported however up to 4GB is recommended for optimal user experience Text is not scrolling Scrolling is not supported in multiline display mode however you can configure for single line operation to see scrolling text Please refer to page 19 DISC 5 setting 37 Disclaimer Important disclaimer please read Unauthorized reproduction or reverse engineering is strictly prohibited Intellectual property included is distributed under specific license agreement with respective owners
16. f the iPod This Playlist is the very first on the list of Playlists 2 pj shown while browsing in Playlist mode This Playlist contains all the songs 3 8 on the iPod Once a Playlist is selected an Artist may be selected within p 8 that Playlist using the Artist Mode Albums by the selected Artist within a z the selected Playlist may be selected in Album Mode ALL ARTIST and E ALL ALBUM designate all available content in those categories Song Charging The interface automatically charges the battery of the iPod when Charging may be shown by an connected and your vehicle ignition key is in the ACC ON position icon that appears on the upper right corner of the iPod screen May vary by model 18 iPod locked unlocked Settings and Features Radio control iPod hold ON iPod hold OFF Limited iPod control v Before connecting the iPod to the MediaBridge module turn the hold switch ON to fully control and browse the songs from the radio The iPod is locked in this state Before connecting the iPod to the MediaBridge module turn the hold switch OFF to fully control and browse the songs from iPod Browsing capabilities are limited from the radio Note Setting the iPod s hold switch must be done prior to connecting it to the dock cable iPod nano 6th generation will always be in locked mode since it does not have a lock switch cs slide to unlock For iPod touch and iPhone when the screen is not
17. h audio streaming playback DISC 4 controls the Autoconnect feature Available options are Enable and Disable This controls whether or not the MediaBridge will reconnect automatically when phone becomes disconnected Only the most recently paired device will be reconnected automatically DISC 5 controls the paired devices memory There is only one option Change tracks to clear the listing of paired devices with the MediaBridge and put module into discoverable mode DISC 6 controls MAT setting Available options are Default Extended Phone only and Off refer to the chart below Options Function Default Reset MAT back to factory default configuration Extended Turn on ALL MAT feature Phone only Turn on the phone relative MAT only off Turn off MAT completely 27 Pairing MediaBridge with your cell phone via Bluetooth 1 Turn on the Bluetooth feature on your cell phone 2 Select MediaBridge as your audio source from your radio then select Bluetooth mode 3 Search device from your cell phone 4 Select MediaBridge from device list and enter password 0000 to connect Note MediaBridge is only discoverable for Bluetooth pairing for the first 60 seconds after selecting Bluetooth mode within the MediaBridge This is indicated with a DISCOVRABL message on the radio display Please perform pairing while the vehicle is parked Bluetooth devices remain paired 30 seconds after exiting MediaBridge mode within this time active audio str
18. icon of the app until a red minus icon shows 3 Tap the red minus icon shown on top of the app 4 This will close the app 5 In a few seconds the iPod music playback app should reinitialize itself and become active again This can be verified by going back to the list of running apps and swiping the screen unit the music control section is shown The iPod app icon next to the music control sections shows that iPod is your audio source Internet Radio App Settings Many radio stations offer lower bitrates Selecting streams with a lower bitrate will reduce data usage and may reduce stream interruptions during the drive For example with the Livio Car Internet Radio app to adjust bitrates manually users can Go to the Setting menu of the device select the Livio Radio settings the change the Maximum Bitrate Filter and set it to 64K Other settings such as Buffer time and Reliability filter may also help in getting a more stable connection Updating Firmware Mac OS illustrated B OCE Firmware Updater v3 0 0 Connect a device Connect module via mini USB Product must be registered before it can be updated Please register your product at hto realster diceeiectronics com Use the following serial number when registering 900012345678 C o Product registration notification The above screen shots are for illustration purposes only AN DICE Firmaare Updater v3 0 0 MediaBridge Dice Electronics Mode usr 1500 vce aaraa Car i
19. king a phone Call ceceeeeeeeeteeeeeeeeees Playing music through MediaBridge via BT ee Accessing the auxiliary input Internet Radio application support Data connection requirement cccee cece eeeeeeeeeeeee Controlling Internet Radio APPS cceeeseeeeteeeteeteeeeeees Text display from the Internet Radio App Terminating the Internet Radio App Firmware Update 22 5 ccsscc2 05yceveacectes deeds dedeedecessenecscensieaveasesce Troubleshooting sxcccessscncarcesrnenstassesencrsincmdianrsnnnaanseriorenseasss WAIT AINY esiscccsiincncceccrnisccsiiencerennasacndaoncctecnn main rin icici 4 Warning and safety Please read these instructions carefully before proceeding Failure to follow instructions may result in improper operation or injury Neither DICE Electronics LLC nor Apple Inc its regional offices distributors or resellers take any responsibility for any damage or injury as a result of using the integration kit Do not open disassemble or alter the interface in any way Do not insert anything into the casing ye Do not cut or try to alter cables in any way and always use the correct connections Only operate unit when stationary or ask passengers to operate it for you Do not allow the Apple iPod iPhone to distract you from driving MK Exercise good judgement and keep your eyes on the road at all times Do not expose unit to extreme temperatures
20. le 3 pin and 6 pin BMW cables iPod USB thumb drives AUX audio device Sirius SC C1 SAT tuner Microphone MediaBridge module MediaBridge vehicle connector AUX connector Sirius SC C1 factory cable USB cable or iPod docking cable Do not connect an iPod dock cable under any circumstance to the SIRIUS module connector Improper connection can cause permanent damage to iPod SIRIUS module 12 Connection diagram for DSP option BMW vehicles with Digital Signal Processing DSP amplifiers must use the DSP Kit PN ACC BMW DSP To confirm if the vehicle has DSP check for a bare metal coax cable and a 3 pin connector for connector locations see page 13 This DSP was only an option on some BMW 5 Series 7 Series X5 Z4 and X3 vehicles DSP Converter Connect to car coax connector Connect to r module Connect to 12V ee switched power and ground Power Cable Connect to car 3 pin connector RCA 6 PIN DSP Harness Fle ee eb BMW Interface Harness 12ft Factory pre wired CD changer cable locations DSP Amp X 3 pin 6 pin or coax connector location Mini 3 Series and Z3 5 Series 7 Series and X5 Z4 13 X3 14 Installation Note Installation should only be performed by a qualified professional Beware of sharp edges to avoid injury and exercise
21. lizer setting can be adjusted while in auxiliary mode by selecting DISC 1 4 and using the TRACK button to increase or decrease levels DISC numbers and corresponding setting are shown on the right chart CHANGE TREBLE EQ SETTING DISC 4 gt lt 4 TRACK gt D S OS SoS a ee SF 9 vY 4555 1 8 mini stereo jack not included 29 Internet Radio Application support iPhone iPod touch This kit includes support for internet radio streaming apps available on muara gt 14 49 3 esna the iTunes Store Thousands of stations can be streamed through data connections Supported apps include Livio Car Internet Radio Pandora iHeart Radio and more Supported features such as text display on screen and next previous track functions will vary by app To learn more about each app specifically please visit the website for the app you need information about Data connection requirements 3G 4G WiFi Users must have an active wireless data connection in order to stream music from an app while in the car Data connections including 3G or 4G through wireless carriers or a third party wireless Internet access point connected to your mobile device through WiFi will work Because this app requires a data connection it will only work on connected devices such as the iPhone and iPod touch 30 Controlling Internet Radio Apps NOTE The following features may not be supported by all apps For de
22. mertace MBR Firmware Version 2496 Serial Number 30012345678 Bootloader Version 1 01 _ Update From File Device specifications and update selection Verifying Device s Program Memory i Firmware update progress 33 the fationng Lanes Agreement You mst acer the terme of hi agreement Nna Sn voce End User cane Agreement r YOU SHOULD CAREFULLY READ TE FOLLOWING END USER UCENSE ACRSIMENT BEFONE INSTALLng Ts SOFTWARE macaAie BY NALIN COPYN OX OTHERWISE USING Ienitio YOU OO NOT ACRE TO TME TERMS OF Tes ACAKLMENT PLEASE License Agreement click Agree to proceed Your module is now up to date Device updated to version 4905 OK een areal Module updated successfully 34 Troubleshooting Problem Solution Radio NAV display only shows DISC Make sure DIP switch settings are correctly set for text display refer to page and track number and there is no iPod 8 for DIP switch settings control Make sure DIP switch settings are correctly set for text display refer to page No text display on radio 8 for DIP switch settings Please also select proper display mode refer to page 19 DISC 5 Make sure the module is reconnected with the vehicle off when changing any dip switches Verify that the vehicle s radio is capable of displaying CD text Some early model year radios don t support text display Correct DIP switch settings but still no text display Check all connections S
23. monstration purposes the following examples will show the features for the Livio Car Internet Radio app The app must be active on the screen of the device To do so simply tap the app s icon and it will load Next previous TRACK buttons execute application specific features such as skipping stream or cycling between station presets DISC 1 6 buttons are associated with station presets when used with the Livio Car Internet Radio application iPhone operating system iOS5 enabled application developers to share the now playing screen information For example when using the Pandora App you will see artist album and song information on the radio s screen When using an application that doesn t implement this feature or running iOS4 only the name of the application will be shown Please note that although iOS 4 4 2 1 is supported on iPhone 3G and iTouch 2nd generation applications do not run in the background As such loading the app takes longer than on devices where the app is present in the background am AT amp T gt V 2 1 33 10X FM Dance 128kbs MP The Project Butter ing Gta i in 3 31 If your listening experience is interrupted by a call under most conditions the app will resume playback at the end of the call Music playback apps running on your iPhone are sent to background automatically when the home button of the phone is pressed but the music playback itself is
24. n Press and hold the desired DISC button preset 1 6 to save as preset e Mini Navigation radio Tune to desired station Press jog DIAL press desired DISC button 1 6 press DIAL to save To recall a memorized channel Simply press the desired DISC preset 1 6 Non Navigation radios to store current station to PRESET 1 6 then _DISC1 6 When done press RND again to deselect Navigation radios Sirius mode o sc 6 to recall PRESET 1 6 stations To store stations to buttons 1 6 DISC 1 6 _ to store current station to PRESET 1 6 2 w Mini Navigation radios Common control O 5 gt O aw Press DIAL Press DISC button 1 6 within Press DIAL lt 4 TRACK gt or to change channel 5 seconds to store station Note If a SIRIUS CONNECT compatible tuner is not detected then a No Tuner message is displayed Go to Channel 000 to view the SIRIUS Tuner ID for activation The 12 digit SID display format is shown in two parts as SID 123456 followed by 789ABC 26 Bluetooth amp MAT Music Announcer Technology configuration To alter voice announcement and Bluetooth pairing settings select Bluetooth as your audio source press the DISC button that corresponds to the feature you want to configure and then use Track to browse through configuration options DISC 1 2 or 3 should be selected if you want to control Bluetoot
25. or Optional accessories sold separately DSP kit Cradle ACC BMW DSP BMW SAT cable DCR 150 USB For more accessories visit www diceelectronics com Microphone USB extension DIP switches overview The configuration switches located on the MediaBridge module are used to set various operation modes of the interface Incorrect DIP switch settings may cause the interface to not work properly or to not operate at all Disconnect the vehicle harness from the module and set the ignition to the off position for 60 seconds after changing the switches then reconnect the module MediaBridge Module 1 2 ON OFF Switch Positions 8 DIP switch settings for BMW Mini The following DIP switch settings are used to configure the MediaBridge module to interface with the various vehicle radios Before installation set the DIP switches to the position shown for the corresponding radios Car configuration switches BMW amp MINI 16 9 Navigation Radio BMW Business CD Radio HOFF OFF BMW 4 3 Navigation Radio BMW MID Radio HOFF EE ON EHON ION HOFF HON For single line Non Navigation radios in Mini 3 Series Z3 Z4 and X3 models For 16 9 wide screen Navigation radio system in BMW and Mini For 4 3 small screen Navigation radio system in BMW For single line Non
26. s Ar This Song Press the MODE button to access MediaBridge as the audio source 01 02 2008 21 buttons to RW or FFW Press the TRACK buttons to go to the next previous song playl ist artist or album depending on which DISC number is selected Press and hold the TRACK Turn the jog dial to change tracks Note that a 5 second timeout is engaged once any of the alternate display buttons are pressed If exiting from any of these sub screens without waiting for the normal timeout you must wait 5 seconds before being able to use the jog dial again to navigate through content 22 You must have the correct display mode selected for proper operation see page 19 DISC 5 Song Artist Playlist displayed here Press the MODE button to access MediaBridge as the audio source Press the TRACK buttons to go to the next previous song playl ist artist or album depending on which DISC number is selected Press and hold the TRACK buttons to RW or FFW On some older BMW radios the m button must be en gaged to perform the same action Illustration showing Mini Navigation radio Unlocked iPod Unlock 33 48 19 North 118 10 25 West Altitude 280 ft Turn DIAL for next previous track Press DIAL to store SIRIUS sta tion presets MediaBridge SIRIUS
Download Pdf Manuals
Related Search