Home

LP040 The instruction manual

1. Attention If this setting is performed successfully the response message will be sent not only to sender s phone number but also to all phone numbers for the warning SMS messages recipients IE GPR LP040 07 2 If the value to store is the same as the original already stored value executing the command will have no effect In this case the modem will only send back the same information as in the case of Information about permitting of the alarm SMS messages So if only the information is sent back though the user entered the setting command it means the parameter is already set as required it wasn t needed to change it 5 2 10 Information about numbers for the alarm SMS messages If the SMS message alarms without any parameters is sent the modem will send back the SMS message with the list of all phone numbers for the warning SMS messages recipients The command alarms The command for reading of information about phone numbers for the alarm SMS messages An example of the response message The list of the alarm phone numbers The list of the phone numbers is The list of the alarm phone numbers The list contains phone numbers 5 2 11 Adding a number for the alarm SMS messages This command is intended for adding the current sender s phone number to the list of phone numbers for the warning SMS message recipients The list can contain up to 8 phone numbers alarms The command for adding a phone number for the
2. The data logger is a target device The modem is intended for communication with this device Generally the data logger types Sxxxx Rxxxx and Gxxxx are supported A complete list of the supported devices can be found in the chapter The list of the supported data logger types on page 39 The paid version of program for data loggers SWRO004 This program makes possible to change of modem settings to communicate with the data logger to read information about actual settings and data logger status to change parameters for data recording and to read measured data Minimal program version must be 2 2 8 0 The latest program versions are available on www cometsystem cz A GPRS connection or a setting cable for example if the GPRS connection is not activated can be used for setting of the modem with this program The M2MTalk server service If you want use SMS messages only you will not have to activate this service For anything else like remote communication with the data logger including data downloading this service must be activated By default this service is not activated by manufacturer In addition if this service is used GPRS must be activated on your SIM card Method and amount of payment for this service are determined by valid trading conditions 3 2 Additional accessories The setting cable QMS2901 The cable is intended for setting of the modem with the program for data loggers from the computer via RS232 serial link
3. This command is intended for removing all phone numbers from the list of phone numbers for the warning SMS message recipients So the list of phone numbers will be cleared completely alarms The command for removing all phone numbers for the alarm SMS messages The possible response messages All alarm phone numbers were removed from The list of phone numbers was the list cleared An error occurred while accessing the The error occured clearing the list of the alarm phone numbers list of phone numbers didn t succeed IE GPR LP040 07 29 5 3 The alarm SMS messages These messages are being sent to the predefined phone numbers independently of the user see the chapter Settings of the communication with the modem and the modem parameters on page 29 The information that the alarm is active and information about correct operation of the data logger can be periodically taken from the data logger by the modem Concretely following states are monitored depending on the connected data logger e the measured value exceeds the alarm limit the alarm is active the binary input state is equal to the chosen state the alarm is active data logger type detection failed communication error the data logger state switched on off the data logger real time clock error the data logger memory is 90 full the data logger memory is full the expected data logger battery life expired the data logger battery voltage is too low If GPR
4. 9 32V DC peak input up to 10W The operating temperature range from 30 C to 65 C External influences according to HD 60364 5 51 normal Operating position arbitrary Device mounting optional equipment self adhesive Dual Lock wall holder DIN rail holder temperature from 40 C to 85 C 105 x 71 x 24mm without antenna and holders cca 180g without antenna and holders anodized aluminum 7 2 The modem interface I RS232 connector 9 pin male 4 yellow indicator LED 2 SIM card holder and connector 5 green indicator LED 3 antenna connector SMA female 6 supply terminal block WAGO 36 TE GPR LP040 07 7 3 A directory information about dimensions with the GSM antenna MP009 1 7 4 Dimensional drawing for a wall mounting of the modem with MP036 105 mm 88 mm 101 mm IE GPR LP040 07 37 38 7 5 Dimensional drawing for a DIN rail mounting of the modem with MP037 24mm 105 mm a GPRS MODEM SER N 71 mm 13 mm 84 mm 31 mm 7 6 Description of the indicator LEDs The green indicator LED The reason does not light the modem isn t connected to a power supply EM the modem power supply is on this is a correct e operation switches off for a short time 7 a checking signal this is a correct operation every cca 30s l the modem is restarting restart takes about 1 blinks minute The yellow indicator LED The reason d
5. It is needed for service purposes only possibly for local settings of the modem during its activation for example if the GPRS connection is not activated Using of standard RS232 crossover cable as current computer equipment is alternative variation New computers are not equipped with serial COM port generally For solution of this problem the converter MP006 RS232 USB is offered It is plugged between computer USB port and the setting cable After installing included driver a virtual serial port in the computer is created for communication with the instrument IE GPR LP040 07 e The self adhesive Dual Lock MD036 The industrial hook and loop fastener for easy installation of the modem on a flat surface e The modem wall holder MP036 The modem wall holder includes 2 screws for mounting on the back side of the modem and set of 2 pieces of wall plugs 2 pieces of screws for mounting on the wall Attention This type of mounting MAY NOT be used if the modem is operated in a vehicle The metal covering of the modem is conductively connected with negative pole of power supply Therefore it cannot be conductively connected with a vehicle chassis ground e The modem DIN rail 35mm holder MP037 The modem DIN rail 35 mm holders include 4 screws for mounting on the back side of the modem Attention This type of mounting MAY NOT be used if the modem is operated in a vehicle The metal covering of the modem is conductivel
6. SMS Check alarm status au Fhone number his 42073712345 Add Edit Delete Phone number in international format fe g 012345678901 Use 4 15 digits Expert Back Wert Sf hoe M Cancel The information that the alarm is active and information about correct operation of the data logger can be periodically taken according to the item Check alarm status from the data logger by the modem These information are processed and then the modem sends alarm SMS messages to a customer according to these analyses If you require sending of the warning SMS messages by the modem you will have to tick off the field Send warning SMS and enter the phone numbers for the warning SMS messages recipients Attention Sending of warning SMS messages from the modem can be temporarily suspended during the executing of some operations which involve data transfers A between the data logger modem and remote computer e g downloading data from a data logger In such cases the SMS messages are stored in a queue and are sent after the operation is finished After pressing Apply button all settings are stored into the modem and then the modem will be restarted Confirm all opened windows with pressing OK button 34 IE GPR LP040 07 6 2 Setting of the data logger parameters If you require sending of the warning SMS messages by the modem for example in the case of exceeding of the alarm limits you wil
7. The current values from the data DP 12 1C logger Sxxxx or RxXxXxXxX Logger Store_13 Templi 24 7C Temp2 The current values from the data the data logger is switched off An error occurred during communication A query can t be processed because with the logger a communication error between the modem and the data logger has occurred Data logger type detecting is still in A query can t be processed because progress please try it later detecting of the data logger type is J st n Progress Lb 18 necessary to repeat the command later 5 1 2 The query about the current values and their alarm settings To take the current measured values from the connected data logger and their alarm settings send the SMS message to the modem The first word of the message must always be values After this keyword parameter values can follow in specific order values phone number 1 phone number 2 IE GPR LP040 07 17 If the SMS message values is sent without any parameters the modem will send the values to telephone number from which the SMS message was sent Otherwise the modem will send the values to telephone numbers which are entered by using these parameters The parameters must be phone numbers in international format Don t enter the square brackets in the SMS message Individual items of the message must be separated by spaces The content of the response message is similar to a query values Moreover if the measured
8. automatically after its switching on but it isn t a standard factory setting To login the modem on the M2MTalk server you can send a SMS message login to the modem phone number The modem will send back an acknowledge SMS message The command The command for login on the M2MTalk server The response message The demand for login on the server was Information about acceptance of accepted demand for login on the M2MTalk server This module is already logged on the The message the modem was already Modem startup is still in progress A command can t be processed please try it later because modem startup has not finished yet It is necessary to repeat the command later Logging on the server is already in A command can t be processed progress because modem is already logging on the M2M server Using server is disabled login is not A command can t be processed accepted because communication with M2M server is disabled IE GPR LP040 07 19 5 2 2 Logout from the M2MTalk server Since the modem is logged on a limited data transferring also proceeds in case the remote communication with the device isn t in progress due to keeping the connection Transferred data is charged as per your GPRS tariff by the mobile operator If you intend to use remote communication via GPRS no longer you can logout the modem from the M2MTalk server to reduce transferred data The command for logout from the M2MTalk server The
9. card on page 10 e The GSM antenna The GSM antenna is also necessary for correct modem operation the facility doesn t work without it It must be mounted into antenna SMA connector It is possible to use the compact GSM antenna MPO009 1 which is offered by the manufacturer In case of need an external GSM antenna can be used e The electric power supply The modem must be powered from an external power supply a power supply adapter an accumulator battery A power supply is connected to a supply terminal block The supply terminal block is a modem component It is possible to use the power supply adapter A1940 which is offered as optional equipment by the manufacturer e The COM adapter IP65 LP012 for data loggers S Rxxxx The adapter is intended for the Sxxxx or Rxxxx data logger and the modem interconnection via RS232 serial link This adapter provides a communication between the modem and the data logger The length of the cable is cca 160 centimeters 4 1 afl ii 2 TE GPR LP040 07 7 Connection cable kit LP010 for data loggers Gxxxx The kit is intended for the Gxxxx data logger and the modem interconnection The kit consists of two cables the cable for the data logger and the modem interconnection via RS232 serial link and the cable for voltage distribution between the data logger and the modem Two pieces of contact tubes are also included along with the cable for voltage distribution The data logger
10. interconnection is provided with the COM adapter IP65 Connect the adapter connector to the RS232 connector on the modem and plug the adapter to the guide slots on the side of the data logger Heed to keep a minimum distance between the modem antenna and the data logger during installation to prevent the data logger interference This distance may not be in any case less than 50 centimeters Keeping the distance at least 1 meter is recommended The correct way to connect is shown in the picture given below The Sxxxx or Rxxxx data logger the modem and other accessories interconnection 12 IE GPR LP040 07 The Gxxxx data logger and the modem interconnection is provided with the connection cable kit LPO1O Attention The metal covering of the modem is conductively connected with negative pole of power supply Therefore it cannot be conductively connected with a vehicle chassis ground Use the self adhesive Dual Lock MD036 for mounting of the modem on a vehicle The cable for voltage distribution between the data logger and the modem must be cut to proper length Strip the insulation from the end of the wires and twine it with separated insulated conductors of the supply line Be careful of the polarity The supplied contact tubes must be forced on the pairs of twisted stripped wires This preassembled set must be connected to a supply terminal block of the data logger On the modem side the contact tubes were already forced on the wires
11. logger are operated in a vehicle it is necessary to have in mind that mobile operators will be allowed to change while crossing borders of various countries If you also want to communicate with the data logger remotely via GPRS in a foreign network you must have activated GSM and GPRS roaming data roaming on your SIM card Moreover the GPRS roaming contract must be concluded between home and foreign mobile operators It is advisable to ask the home mobile operator about it even before going abroad When in use GPRS roaming mode GPRS transferring prices can be markedly higher than in the case of a home network A PIN code entering must be deactivated on the SIM card Using the SIM card in any mobile phone is the simplest method how to make sure that a PIN code entering is deactivated If a demand for entering a PIN code is displayed after switching the mobile phone on you will have to deactivate a PIN code entering This procedure is dependent on a type of the mobile phone and it should be described in a mobile phone s user manual The SIM card is put in a holder The holder is a modem component The holder is ejected by pressing the button beside the holder by using a fit instrument for example a pencil Insert the prepared SIM card into the holder See that the SIM card stays in alignment with the holder correctly for all its size After it the holder with the inserted SIM card is pushed in the modem The correct way to install the SIM card is
12. login a text server the M2MTalk server name or IP address a text e port the port number a number value If the modem accepts the command the SMS message will be sent back And if the modem was logged on the M2MTalk server the modem will be restarted automatically An example of the command with parameters m2mtalk yes no 2006 2006 mypsw The communication via M2MTalk server will be enabled automatic login after switching on will be deactivated address will be 2006 user name will be 2006 and the password will be mypsw The M2MTalk server name or IP address and the port number stay unchanged The response message M2MTalk server parameters were set and All parameters were set and stored An error occurred while setting M2MTalk An error occurred during setting succeed 22 TE GPR LP040 07 If all values to store are the same as the original already stored values executing the command will have no effect In this case the modem will only send back the same information as in the case of Information about the M2MTalk server connection settings So if only the information is sent back though the user entered the setting command it means all parameters are already set as required it wasn t needed to change them 5 2 8 Information about permitting of the alarm SMS messages If the SMS message alarms without any parameters is sent the modem will send back the SMS message with information whether sending of the alarm SMS
13. messages is enabled or not alarms The command for reading of information about permitting of the alarm SMS messages The possible response messages Sending of warning messages is switched Sending of the alarm SMS messages fe is enabled Sending of warning messages is switched 5 2 9 Setting of permitting of the alarm SMS messages The syntax of this command is either alarms on or alarms off In the first case sending of the alarm SMS messages will be enabled Alarm states will be checked periodically If any alarm occurs the alarm SMS message will be sent to the predefined phone numbers In the second case sending of the alarm SMS messages will be disabled alarms on Sending of the alarm SMS messages will be enabled An example of the response message Sending of warning messages was switched Sending of the alarm SMS messages on from number 420123456789 was enabled from the phone number 420123456789 An error occurred while switching sending The error occurred saving of the of warning messages on parameter didn t succeed The command alarms off Sending of the alarm SMS messages will be disabled An example of the response message Sending of warning messages was switched Sending of the alarm SMS messages off from number 420123456789 was disabled from the phone number 420123456789 An error occurred while switching sending The error occurred saving of the of warning messages off parameter didn t succeed
14. set as required it wasn t needed to change them IE GPR LP040 07 21 5 2 6 Information about the M2MTalk server connection settings If the SMS message m2mtalk without any parameters is sent the modem will send back the SMS message with information about the M2MTalk server connection settings m2mtalk The command for reading of information about the M2MTalk server connection settings An example of the response message Enabled yes Autologin yes Information about the M2MTalk Address 1234 User usr server connection settings Password psw Server example com Port 9999 5 2 7 Setting of the M2MTalk server connection The first word of the message must always be m2mtalk After this keyword parameter values for an actual setting follows in specific order m2mtalk enabled autologin address user password server port If the trailing parameter values are not entered they will be unchanged Don t enter the square brackets in the SMS message Individual items of the message must be separated by spaces The parameters are optional from the back If any parameter isn t entered it will not be changed The meaning of the parameters is following e enabled enable the communication via M2MTalk server yes no e autologin automatic login on the server after switching on the modem yes no e address the modem address a number value e user the user name for login a text e password the password for
15. LP040 The GPRS modem for data loggers Sxxxx Rxxxx Gxxxx The instruction manual Please read the instruction manual before the first device connection This version describes FW 2 0 2 Contents 1 Description of working of the modem cc ccescesccceccccecceeesseeecceeeeecaaeseeeeeeeeeeeeaaeeneeeeeeseeeqaas 4 s GICMERANS ALCL Oe Sa sand ear ct ee eae ane E a ees 5 Ds Ehe moden ANG 11S ACCES SOMES rissa itsretiancccnasiencentntoisstaaa arene diectt ae cnntn tase Mace emtectt ae cenentons 7 ile ACCESSOTIES MCCUCO 10 OP ALON crann na A TA 7 e TIS SIN Carda eons cise E E eisand etme tees iaseaiad arate 7 OTC SA aneneen ea E N E E 7 lt Thecketiic power SUD Ply enere A een ees 7 e The COM adapter IP65 LPO12 for data loggers S RXXXX ceecccccccccccessseeeeeeeeeeeeeaeeeeeees 7 e Connection cable kit LPO1O for data loggers GXXXX woe seseesseceeeeeeeeeeeeeseeceeeeeeaeeeeeees 8 Thedat 048 cr errepreneNe orn a eee ee Rear ee cre rn Sse rR ree em oR eS eee ES ee re 8 e The paid version of program for data loggers SWRO04 s nnnenessssssssserrsssssssseerrssssssssseeeees 8 Toe IIIT a server Se Ce aeons E ance shee ena E eh aac ene oie Nena gaunt dase saan tac 8 os HNO CIMIONAACCES SOULE Sisssiersh cs denneleviat eds e andattusaasined ven deenetepaabeduandeenduanatendeoes 8 Pie Sette Cae ONS 2 Ua icra elas scesctenettenne teeter cco owas E T S 8 The self adhesive Dual Lock MDOS Ge crisis ces n
16. S connection isn t activated you will have to set up the alarm SMS messages parameters by using the setting cable Following parameters must be set with the program for data loggers e data logger reading interval e sending no sending of the warning SMS messages e phone numbers for the warning SMS messages recipients 5 3 1 Active alarms of the data logger Exceeding of the alarm limit for measured values and reaching of the chosen state for binary inputs are evaluated by the data logger To work it correctly following parameters must be set for the data logger e the data logger must be switched on e the alarm conditions must be set with desired means for all monitored channels e the alarm evaluating must be enabled for all monitored channels The incoming SMS message contains the same informations as in the case of the query about the current values and their alarm settings The measured value exceeds the alarm limit The incoming alarm SMS message Example 1 The current values and their alarm 12345678 1 24 7C 19 0 26 0 2 settings from the data logger 45 5 RH 0 0 50 0 6 12 1C 0 0 10 0 Example 2 Logger Store_13 T 24 7C 19 0 26 0 RH 45 5SRH 0 0 50 0 DP 12 1C 0 0 10 0 26 TE GPR LP040 07 The binary input state is equal to the chosen state data loggers Gxxxx only The incoming alarm SMS message Example 1 The current values and their alarm 12345678 1 24 7C 19 0 26 0 1m 2 settings from the dat
17. Setting up a modem GPRS Modem COM Adapter E Ja Logger Gxxxx ia Feeder cable and M2M GPRS communication cable i y INTERNET M2MTalk server Downloading data from logger Showing of current values Setting up a logger Setting up a modem Working principle for the modem with the data logger block diagram 4 IE GPR LP040 07 2 General safety rules The following summary describes a basic safety features related to device installation and operation Please read it properly before device installation The following safety precautions must be observed during all phases of the operation usage installation or repair of the device Operate the instrument in accordance with this manual to prevent damage of this device damage of three side devices or electric trauma Comet system s r o declares that the modem LP040 complies with the essential requirements and other relevant provisions of Directive 1999 5 EC Declaration of Conformity is available at www cometsystem cz A Risk of electric shock Do not use the instrument without the cover Use only a safety adapter with the power voltage recommended by device manufacturer Before connecting check that the adapter has undamaged cables and cover Do not use the instrument if it does not work correctly If the instrument seems not to work correctly have it checked by a qualified service person Qualified service and installation Service should be perf
18. Using these messages you can take the current measured values from the connected data logger the modem firmware version and the current modem state information 5 1 1 The query about the current values To take the current measured values from the connected data logger send the SMS message to the modem The first word of the message must always be values After this keyword parameter values can follow in specific order values phone number 1 phone number 2 If the SMS message values is sent without any parameters the modem will send the values to telephone number from which the SMS message was sent Otherwise the modem will send the values to telephone numbers which are entered by using these parameters The parameters must be phone numbers in international format Don t enter the square brackets in the SMS message Individual items of the message must be separated by spaces If a data logger Sxxxx or Rxxxx is connected to the modem it will send back a SMS message with the following contents e data logger identification the user s description of the data logger is displayed If this description isn t set the serial number of the data logger will be displayed If the total message length would exceed 160 characters the serial number of the data logger will be displayed instead of the description e measured values of single quantities the channel number or channel description if it is set is displayed the measured v
19. a logger 125 0C 10 0 24 0 2m 3 OFF 1m 4 ON 10m Example 2 Logger Store_13 Templ 24 7C 19 0 26 0 Im Temp2 25 0C 10 0 24 0 2m Binl OFF lm Bin2 ON 10m 5 3 2 Other data logger states Data logger type detection failed A problem occurred while detecting a The modem is not unable to logger type determine type of data logger which 1s connected to it Most likely communication between the data logger and the modem will not be functioning properly Communication error The incoming alarm SMS message An error occurred during communication An error occurred while with the logger communication between the modem and the data logger The data logger state Switched on off data loggers S Rxxxx only The incoming alarm SMS message The logger is switched off The data logger is switched off The incoming alarm SMS message The logger is switched on The data logger is switched on The data logger real time clock error The incoming alarm SMS message The logger real time clock error The data logger real time clock isn t adjusted correctly The data logger memory is 90 full data loggers S Rxxxx only The logger memory is 90 full The data logger memory is 90 full IE GPR LP040 07 27 The data logger memory is full The incoming alarm SMS message The logger memory is full The data logger memory is full The expected data logger battery life expired data loggers S Rxxxx only The i
20. adio frequency energy while switched on Remember that interference can occur if it is used close to TV sets radios computers or inadequately shielded equipment Always switch off the cellular device wherever forbidden or when you suspect that it may cause interference or danger Service availability Devices operate using radio signals and cellular networks Because of this connection SMS GPRS etc cannot be guaranteed at all times under all conditions Therefore you should never rely solely upon any wireless device for essential communications emergency systems safety related systems Remember for hi reliability systems is redundancy necessary For more information please see IEC 61508 TE GPR LP040 07 3 The modem and its accessories To use the entire facility not only the modem but proper accessories are also required 3 1 Accessories needed to operation e The SIM card The SIM card is necessary for correct modem operation It makes possible to send SMS messages and to communicate with the data logger remotely via GPRS In addition GPRS data services must be activated for data transferring via GPRS If the running modem is used among areas with different mobile operators GSM and GPRS roaming data roaming must be also activated Method and amount of payment for these services are determined by your mobile operator A PIN code entering must be deactivated on the SIM card For more details see the chapter The SIM
21. alarm SMS messages An example of the response message The alarm phone number 420123456789 was The sender s phone number was added added to the list tor the List The alarm phone number 420123456789 is The sender s phone number was not already contained in the list added to the list because this number already occurs in the list The list of the alarm phone numbers is The sender s phone number was not already full added to the list the list is already full An error occurred while accessing the The error occured adding the list of the alarm phone numbers sender s phone number didn t succeed 24 TE GPR LP040 07 5 2 12 Removing a number for the alarm SMS messages This command is intended for removing the current sender s phone number from the list of phone numbers for the warning SMS message recipients alarms The command for removing a phone number for the alarm SMS messages An example of the response message The alarm phone number 420123456789 was The sender s phone number was removed from the list removed from the list The alarm phone number 420123456789 was The sender s phone number was not not contained in the list removed from the list because this number was not found in the list An error occurred while accessing the The error occured removing the list of the alarm phone numbers sender s phone number didn t succeed 5 2 13 Removing all numbers for the alarm SMS messages
22. alue and the quantity unit follow 16 TE GPR LP040 07 The response message example Logger Store_13 Temp 24 7C Hum 45 5 RH DP 12 1C If a data logger Gxxxx is connected to the modem it will send back a SMS message with the following contents e data logger location the user s description of the data logger location is displayed If this description isn t set the serial number of the data logger will be displayed If the total message length would exceed 160 characters the serial number of the data logger will be displayed instead of the description e measured values of single quantities and current binary inputs states the channel number or channel description if it is set is displayed If a measured quantity is assigned to the channel the measured value and the quantity unit will follow If a binary input is assigned to the channel the user s description of the current binary input state will be displayed The response message example Logger Store_13 Temp 24 7C Temp2 25 0C Binl OFF Bin2 ON If it is not possible to take information about the values 1 e the data logger is switched off a communication error between the modem and the data logger has occurred or detecting of the data logger type is in progress the modem will send back a SMS message with a proper error description The command for reading of the current values An example of the response message Logger Store_13 Temp 24 7C Hum 45 5 RH
23. at the factory The correct way to connect wires for the feeder cable is shown in the table given below The wire Connection to a supply terminal Connection to a supply terminal block of the data logger block of the modem red stripped the positive pole terminal U the positive pole terminal the negative pole terminal GND the negative pole terminal The connector of the communication cable must be connected to the RS232 connector on the modem and the wires of this cable must be connected to the supply terminal block on the data logger The correct way to connect wires for the communication cable is shown in the table given below Connection to a supply terminal red yellow black brown Heed to keep a minimum distance between the modem antenna and the data logger during installation to prevent the data logger interference This distance may not be in any case less than 50 centimeters Keeping the distance at least 1 meter is recommended The correct way to connect is shown in the picture given below Lmin 0 5m The Gxxxx data logger the modem and other accessories interconnection IE GPR LP040 07 13 4 4 Switching on the modem The properly assembled modem is switched on by feeding of electric voltage into the modem supply terminal block The green LED diode lights up The modem will be prepared for communication after cca minute from its switching on It is advisable to check the communication b
24. e parameter service The available way how to achieve it click on the button Start select the item Run then select the item Browse find the program LOGGER EXE in your drive if the destination of this program wasn t changed during installation it will be placed in the directory C Program Files CometLoggers Logger Logger exe select it by using the mouse and click on the button Open In the displayed field Open write the char space followed by parameter service at the end of displayed path past the quotation mark Then click on the button OK After program start the submenu Service should appear in the main menu Select the item M2M modem in the submenu Service Choose the correct COM port number and confirm it with pressing OK button Now you can set up all modem parameters with no limitations TE GPR LP040 07 35 7 Technical specification 7 1 Technical parameters Communication with the device Frequency band Output power SIM card type GPRS class Antenna Supply terminal block IP code Operating conditions Storage conditions Dimensions Weight Box material RS232 connector Canon 9 for the COM adapter 850 900 1800 1900 MHz Class 4 433dBm 2dB for EGSM850 Class 4 33dBm 2dB for EGSM900 Class 1 30dBm 2dB for GSM1800 Class 1 30dBm 2dB for GSM1900 1 8V or 3V multislot class 12 50 ohm SMA connector removable WAGO 734 max size of conductors 1 5 mm IP30 The power supply external
25. er detecting of the data logger type LS Just Im progress It 15 necessary to repeat the command later 5 1 3 The query about the modem firmware version To take the modem firmware version send the SMS message firmware to the modem The command The command for reading of the modem firmware version Datalogger Communicator v 1 1 0 The modem firmware version 18 IE GPR LP040 07 5 1 4 The query about the current modem state information To take the current modem state information send the SMS message gsmstatus to the modem The modem will send back a SMS message with followed information The command for reading of the current modem state information An example of the response message Uptime Od Ohr 26min M2MTalk online Elapsed time from the modem s yes Operator T Mobile CZ T Mobile Swit ChaenG ON CZ RSSI 66dbm Signal 99 Registered on The current M2MTalk server login The SIM card registration on the cellular network GSM The SIM card registration on the foreign network it says if the roaming iS active 5 2 The statement SMS messages Using these messages you can control and set up the modem remotely 5 2 1 Login on the M2MTalk server If you intend to use remote communication with the modem or data logger via GPRS for example to set up this device remotely the modem always must be logged on the M2Mtalk server before starting the communication The modem can be set up to login on the server
26. esserstaviiansonciueniauatnans uetcertdapibatonsiaeaaateceuess 9 Theoden wallynolder MEO Gisissecssiesccatitts cotosa a a tesa Oiler eenedu uae ica eumeaeees 9 e The modem DIN rail 35mm holder MPO37 orrae E 9 A 2 VK aah abo 2 L218 0 a ir Ren T en SCO O Sai mre 10 Bil Chock Ol ACCES SONICS yin cisi setae aa ele cate at oe aeaneshary ogee ee eee cesta eee 10 ADs OLIWALG INS CAA OM eein tencahonitelicnan snide A anise cdaanseceantn elimina ayes 10 ADs Pnemodemassemb lino toad di aater ut out aeiiat erat a oat cater ad eeaeatenat 10 4 3 1 MGT SVC A Ch os eet E ET E ete E E A E E eee E E S E 10 43 2 Me ApS VE AST ies a E a ea tausenet en aaannatas 11 4 3 3 Connecting the power supply to the modem sssssoeeesssssssseerresssssssseerrssssssseeeeees 11 4 3 4 The data logger and the modem interconnection cccccecceceeeseeeeeeceeeeceeaaeeseeeeeeees 12 Ad Switching onthe Mode Miercssiassgnn n a Uunghiaea aes cubaaelatasvecditns 14 ds SCL LMS MOJEN seris A E A E adveeaendeeeese 14 4 5 1 Setin of GPRS connection parameters serors as aE a EA a 14 4 5 2 setting of M2M Talk chent parameters eeror a a T 14 4 6 Login the modem on the M2MTalk servet ccccccssssssseececceeceeeesseeecceeeeeeaaeeeeeeeeeeeeeaas 15 Ate SEMN OFCOMEr parane eT Sree E NEE 15 Ds Comm nmcaton via SMS MESSAGES on aa E e ai 16 Delt THEeGU VSMS MOS Oana a a pee enced eee 16 SEN Theguery about the cutrent Values icesrii e ead ale ea
27. etting this parameter values via SMS command see the chapter Setting of the GPRS connection on page 20 The example You can set up the parameter apn to value internet without other parameters user password and dns by sending the SMS message gprs internet For getting information about GPRS connection parameters please contact an appropriate mobile operator 4 5 2 Setting of M2MTalk client parameters These parameters are already preset at the factory don t change it gratuitously If you can verify a setting compare it with data listed in the card which was delivered with the modem M2MTalk client parameters can be set via the SMS command see the chapter Setting of the M2MTalk server connection on page 22 or via the setting cable see the chapter Setting of the modem using the setting cable on page 35 14 TE GPR LP040 07 4 6 Login the modem on the M2M Talk server If you intend to use remote communication with the modem or data logger via GPRS for example to set up this device remotely the modem always must be logged on the M2Mtalk server before starting the communication The modem can be set up to login on the server automatically after its switching on but it isn t a standard factory setting To login the modem on the M2MTalk server you can send a SMS message login to the modem phone number The modem will send back an acknowledge SMS message It is advisable to check the login status by sending SMS message gsmstatus to
28. hapter 6 1 on page 29 e phone numbers for the warning SMS messages recipients see the chapter 6 1 on page 29 e phone numbers from which the incoming SMS messages will be accepted by the modem see the chapter 6 1 on page 29 e setting of the alarm conditions for the data logger if this functionality is required see the chapter 6 2 on page 35 TE GPR LP040 07 15 5 Communication via SMS messages It is possible to control and monitor the device operation remotely via the special SMS messages which are being sent to the modem phone number The user can select phone numbers from which the SMS messages are accepted by the modem The factory configuration doesn t restrict the phone numbers for any incoming SMS messages that means any SMS messages are accepted regardless of the sender phone number Phone numbers restriction can be done with the program for data loggers see the chapter Settings of the program for data loggers to use it with the modem on page 29 Generally SMS command messages aren t case sensitive and the space serves as a parameter separator If the accepted command isn t supported or it hasn t a correct syntax or parameters the modem will send back an SMS message with a proper error description This information will be returned only three times in maximum The fourth and every next incorrect command from the one phone number is ignored until the incoming command will be correct again 5 1 The query SMS messages
29. ically after its disconnecting IE GPR LP040 07 39
30. l have to set these data logger parameters at least e the data logger must be switched on e the alarm conditions must be set with desired means for all monitored channels e the alarm evaluating must be enabled for all monitored channels If you use GPRS connection for communication with the data logger you will be allowed to set up the data logger remotely by using the program for data loggers For the remote connection you must select the item Select port manually in the window File Options Communication and confirm it with pressing OK button Then select the item Configuration Device setting in the main menu Choose the correct communication port name from the displayed list If you don t use GPRS connection for communication with the data logger you will be allowed to set up the data logger locally via the proper communication adapter COM adapter IP65 USB adapter Use the program for data loggers to set up data logger Attention The serial communication interface of data logger Gxxxx is out of service while the data logger is connected with a computer via a USB communication cable It A means that communication between the data logger and connected GPRS modem will not proceed during this period 6 3 Setting of the modem using the setting cable If GPRS connection isn t available you will have to use the setting cable for setting up the modem with no limitations In this case the program for data loggers must be run with th
31. ncoming alarm SMS message The end of the expected logger battery The expected data logger battery life life expired The data logger battery voltage is too low data loggers S Rxxxx only The incoming alarm SMS message The logger power supply is low The data logger battery voltage is too low 28 TE GPR LP040 07 6 Settings of the program for data loggers to use it with the modem Attention If GPRS connection isn t available you will have to use the setting cable Move ahead the chapter Setting of the modem using the setting cable on page 35 All following parameter settings are mentioned for an information only the correct values must be entered everywhere 6 1 Settings of the communication with the modem and the modem parameters Run the program for data loggers Select the item File Options in the main menu In the window Options select the item M2M connection on the left bar first A following window will be displayed Options l Es Data storing oe Communication oe Data presentation B 2h connection He Aukodawnload Sener talkserver m2msensor com Eart M2hd connection PC to M2ZM server Connection parameters PC s MaM address Se MeM login password A cs The items Server and Port are already pre filled don t change it gratuitously Fill the items PC s M2M address a M2M login password with data listed in the card which was delivered with the modem Confirm these se
32. oes not light a GSM part is switched off the modem is successfully connected via the cellular network GSM 1 e the modem replies for the SMS messages GPRS isn t connected blinks two times for a short GPRS connection is active 1 e it 1s possible to time every cca 3s communicate with the data logger remotely the modem replies for the SMS messages the SIM card is not inserted a PIN code isn t deactivated on the SIM card blinks regularly the GSM antenna isn t mounted searching for the network is in progress login to the network is in progress blinks one time for a short time every cca 3s IE GPR LP040 07 7 1 The list of the supported data logger types The supported data logger types R0110 R0111 R0121 R0122 R0141 R0841 R3120 R3631 R3541 R6011 R6021 R5011 R5021 R3121 ROLIOE S0110 S0111 S0121 S0122 S0141 S0841 3120 S3631 S3541 S6011 S6011 S6021 S6021 S5011 S5011 S5021 S5021 3121 7021 S0541 S0442 3532 S7841 S0842 SO110E SOLLOF SO111F G0241 and G0841 data loggers support was added 8 Technical support Technical support is provided by a distributor of this device The contact is presented in the included warranty certificate In case of need you can also make use of a discussion forum on http www forum cometsystem cz A short description of the discussion forum is on http www cometsystem cz forum htm 9 Liquidation The device must be liquidated ecolog
33. ormed by a qualified person only We recommend you use only original accessories to avoid possible damage When connecting to any other device read its user guide for detailed safety instructions Do not connect incompatible products It is forbidden to connect other devices while the device is under electric voltage If a damage of the device occurs due to gross violation of these rules a free guarantee repair will not have to be executed Usage in hospitals When in a hospital or other health care facility observe the restrictions on the use of mobiles Respect the directions and switch the cellular device off on places where using mobile phones is forbidden Medical equipment may be sensitive to RF energy Switch off in aircraft Switch off the cellular device before boarding an aircraft Make sure it cannot be switched on inadvertently The operation of wireless appliances in an aircraft is forbidden to prevent interference with communications systems IE GPR LP040 07 5 Avoid fire and explosion Do not use the instrument in an explosive environment Do not operate the cellular device in the presence of flammable gases or fumes Switch off the cellular device when you are near petrol stations fuel depots chemical plants or where blasting operations are in progress Operation of any electrical equipment in potentially explosive atmospheres can constitute a safety hazard Interference Your cellular device receives and transmits r
34. pes cccccccsssssssccecceceeeaeeseeeceeeeeeaaeeeeeeeeeeeeeeaaas 39 Se Tocame Suppor ah ice let er tered teen ne aac tase eines a One ince A tee tea sr tee 39 9 TAGUIC At Oireen E A 39 IE GPR LP040 07 3 1 Description of working of the modem The modem is intended for remote communication with data loggers Sxxxx Rxxxx Gxxxx via cellular network GSM In light of a customer this way of communication offers the same functions like a direct connection between the data logger and the computer for example by using COM USB adapter The modem can be set and controlled with a program for data loggers and also with SMS messages but with restrictions It is possible to select phone numbers from which SMS messages are accepted by the modem These are possibilities of usage the program for data loggers e downloading data from the connected data logger e reading of current values from the connected data logger o setting up the modem locally via RS232 link e setting up the modem remotely via GPRS networking o setting up the connected data logger remotely These are possibilities of usage the SMS messages e sending of alarm SMS messages to preconfigured phone numbers in case of beyond the set alarm limits for measured values and binary inputs or in case of error conditions e getting of current values from the connected data logger e setting up the modem remotely with restrictions Logger Current values RXXXX Alarms SXXXX
35. r for the alarm SMS message ccccccsssseeeseeeeeeeeeaeeesseeeeeees 25 5 2 13 Removing all numbers for the alarm SMS messages ccccsssessecceeeceeeeeeeeeeeeeees 25 2a hie alarm S MS mesa eSa E aleeeialane 26 2 ie el Actiye alarms OF the data lOS COR cenusie a a a eah 26 T Oe UME rata logoer Sta CCS eeni a a 21 6 Settings of the program for data loggers to use it with the modem ccccesesseeeeeeeeeeeeeeees 29 6 1 Settings of the communication with the modem and the modem parameters 29 6 2 Seting or the datalogger parameters yess cceivcuagivenooehiats dima vianestaeteienaotncedeaioebseneeces 35 6 3 Setting of the modem using the setting Cable noossseonnnssssssssseerrssssssssceersssssssseeresssssssses 35 Te TecmmicalspecihieaNON sa casthaasucnen stables naw meniieuateaigesmce iets teniaascecesaehes 36 Take Techmeal Parameters srecreicranecetiee a E 36 Ts MVS TNO CLS TAY mteri tists ata E ce stove San esactae saben tea acacia ele eaeas 36 7 3 A directory information about dimensions with the GSM antenna MP009 1 37 7 4 Dimensional drawing for a wall mounting of the modem with MP036 ccccccee 37 7 5 Dimensional drawing for a DIN rail mounting of the modem with MP037 00 38 COo Desenptonor the mdicator LEDS je bsueseiestoirntsanseenesiarealawiniehacaeny ea detandieucelondaismsnieencewen tel 38 7 7 The list of the supported data logger ty
36. response message The demand for logout on the server was Information about acceptance of accepted demand for logout from the M2MTalk server This module is not logged on the server The message the modem wasn t logged on the M2MTalk server Modem startup is still in progress A command can t be processed please try it later because modem startup has not finished yet It is necessary to repeat the command later 5 2 3 Restart of the modem This command is intended for the remote restart of the modem for example in the event of the problem with GPRS connection The complete restart of the modem takes about 2 minutes The command The command for restart of the modem The response message The demand for application restart was Information about acceptance of accepted demand for restart of the modem 5 2 4 Information about the GPRS connection settings If the SMS message gprs without any parameters is sent the modem will send back the SMS message with information about the current GPRS connection settings gprs The command for reading of information about the GPRS connection settings An example of the response message APN internet User Password DNS Information about the GPRS connection settings 5 2 5 Setting of the GPRS connection The first word of the message must always be gprs After this keyword parameter values for an actual setting follows in specific order gprs apn user pa
37. scription of connection choose your own name Fill the item Address with data listed in the card which was delivered with the modem If you want to prevent unauthorized access to your modem data logger you will have to fill the item Secure communication key with your entered password Remember this password well it will have to be entered during setting of the modem later Continue with pressing Modem configuration button Communication with the modem begins If all previous settings are correct a following window will be displayed If not please check the settings described in the chapter Settings of the communication with the modem and the modem parameters on page 29 TE GPR LP040 07 31 GPRS modem settings op x Mz Talk server Insert parameters to establish connection between modem and M2M server This information is delivered to every moder W MM communication On Off Accoun Auto login to Meh server m ser 2003 Basswood Connectio GEET ftalkserver m2msensor com Eart 9999 Modem address 2003 Security communication key M pSecurekep i Back Next gt gt M Cancel In this window enter Security communication key according to setting in the window M2M port properties on page 31 If you require the modem s login on the server automatically after its switching on so that GPRS communication can be available you will have to tick off the field Auto login to M2M server Don t change o
38. shown in the picture 10 IE GPR LP040 07 The way to install the SIM card 4 3 2 The GSM antenna The GSM antenna must be mounted to the antenna connector by lightly tightening a sleeve nut 4 3 3 Connecting the power supply to the modem The power supply is connected on a WAGO terminal block which is a modem component Insert a flat bladed screwdriver to rectangle terminal hole and push the screwdriver towards away from you the contact is released Connect a wire to the released terminal and close the terminal by removing the screwdriver Connect positive pole of the terminal marked with and negative pole of the terminal marked with The correct way to connect wires is shown in the picture given below Way to connect wires The entire terminal block is possible to remove from the modem by pulling it up from the connector TE GPR LP040 07 11 In the case of using the power supply adapter A1940 connect the white wire to positive pole and the black wire to negative pole 4a D O ee 4 Connecting of power supply adapter A1940 If the modem and the data logger Gxxxx are operated in a vehicle it will be necessary to use the cable for voltage distribution between the data logger and the modem For more detailed information see the chapter The data logger and the modem interconnection on page 12 4 3 4 The data logger and the modem interconnection The Sxxxx or Rxxxx data logger and the modem
39. ssword dns 20 TE GPR LP040 07 If the trailing parameter values are not entered they will be deleted Don t enter the square brackets in the SMS message Individual items of the message must be separated by spaces The meaning of the parameters is following e apn the access point name e user the user name for login e password the password for login e dns the DNS server name or IP address If any of the parameters user password or dns are not entered from the back they will be always deleted If the modem accepts the command the SMS message will be sent back And if the modem was logged on the M2MTalk server the modem will be restarted automatically An example of the command with parameters gprs internet Setting of the parameter apn to the value internet The values of the parameters user password and dns will be deleted The response message GPRS parameters were set and stored All parameters were set and stored correctly An error occurred while setting GPRS An error occurred during setting parameters the parameters Their saving didn t succeed If all values to store are the same as the original already stored values executing the command will have no effect In this case the modem will only send back the same information as in the case of Information about the GPRS connection settings So if only the information is sent back though the user entered the setting command it means all parameters are already
40. t eats 16 52 The query about the current values and their alarm SettingS cccccccsssseeseeeeeees 17 5 1 3 The query about the modem firmware version ccccccccccccceeeeesseeeeeeeeeeaaseeeeeeeess 18 5 1 4 The query about the current modem State information cc ceeeeeeeeeeeeceeeseeeeeeeeeees 19 Did Tie Statements MS TNCSSA CCS iea A E 19 JN Lesion the VIZ MT alk sef yefe a a a a Se beeetes 19 a2 Losout from the VID MIT al Set Vier usaron AE EAE 20 Dida IRES ARMOl Tie MOUEIN ge55cutesecetiiassiauduaestAi ae netusecesee daa iaaeteaardt cath ucupeceieniuaessauseneteees 20 5 2 4 Information about the GPRS connection settings esesssssseoeeresssssssseerrsssssseeeerees 20 529 Scetine OF the GPRS CONNEC Olsena a E E 20 52220 Information about the M2MTalk server connection settings cccccccccsssseeeeeeeeees 22 S241 Setting of the M2MTalk server connection ccccccccssssesseeeeceeeeeaeeeeeeeeeeeeeeeaaaeeeees 22 5 2 8 Information about permitting of the alarm SMS messages ccccccececcceesseeeeeeeeees 23 3 29 Setting of permitting of the alarm SMS messages ccccccccccececeesseeeeeeeeeeeeeeeeeeees 23 5 2 10 Information about numbers for the alarm SMS messages ccccccceeeceessseeeeeeeees 24 2 IE GPR LP040 07 5 2 11 Adding a number for the alarm SMS Messages ccccccccccccccesseeeeeecececeeaaeeesseeeeees 24 5 2 12 Removing a numbe
41. the modem phone number If the modem works correctly it will send back SMS message with information The login status is also including in these information M2MTalk online yes Attention Since the modem is logged on a limited data transferring also proceeds in case the remote communication with the device isn t in progress due to keeping the connection Transferred data is charged as per your GPRS tariff by the mobile operator AN Around 26 kB of data per day are transferred for keeping connection purposes If the full up data logger memory is about to be downloaded around 73 kB of data per day are transfered for data loggers S Rxxxx and around 1162 kB of data per day are transfered for data loggers Gxxxx Logout from the server is described in the chapter Logout from the M2MTalk server on page 20 4 7 Setting of the other parameters The information that the alarm is active and information about correct operation of the data logger can be periodically taken from the data logger by the modem These informations are processed and then the modem sends alarm SMS messages to a customer according to these analyses The program for data loggers is used for setting of these parameters If GPRS connection isn t activated you will have to set up the modem by using the setting cable There are these parameters e data logger reading interval see the chapter 6 1 on page 29 e sending no sending of the warning SMS messages see the c
42. ther parameters in this window gratuitously it can cause problem with communication After pressing Next gt gt button the window for settings of phone numbers restriction for communication via SMS messages will be displayed 32 IE GPR LP040 07 GPRS modem settings Oe x SMS remote control Insert phone numbers from which modem accepts SMS commands Commands from other phone numbers will be ignored If the following lists empty modem accepts SMS commands from all phone numbers Phone number lis 4703 71 235456 Phone number in international format e g 012345678901 Use 4 15 digits Expert Back Next gt x Cancel Communication via SMS messages can be restricted to selected phone numbers only If no phone numbers are in the list the modem will process the incoming SMS messages from all phone numbers If you add some phone numbers to this list the modem will process the incoming SMS messages only from these selected phone numbers After pressing Add button enter the phone numbers from which you want to send SMS command messages to the modem All phone numbers must have the international format for example 420123456789 After pressing Next gt gt button the window for settings of the alarm SMS messages parameters will be displayed IE GPR LP040 07 33 GPRS modem settings OP x Alarms SMS alarm settings Insert phone numbers of warning SMS recipients Send warning
43. ttings with pressing Apply button Further in the window Options select the item Communication on the left bar A following window will be displayed IE GPR LP040 07 29 5 Options a Data storing Communication Communication Data presentation Serial ports Device models Mabli connection C Search all serial ports Autodowrload P Wo Dataloggers lee Das new C Search only ports BlackBoses with or without display iW Dataloggers Black Bos types L TN Mains failure loggers E i Commeter E f Select port manually List of ports A Select the item Select port manually and press the button List of ports The window List of communication ports will be displayed List of communication ports interface pe COM COMe2 Seral COMe Add port Delete port iI Properties Lo a cen In this window press the button Add port The window Add communication port will be displayed 30 IE GPR LP040 07 Add communication port Interlace typ Serial port COM C LAN Adapter C GSM Mavecom modem x cores Select the item GPRS M2M modem here and then press the button Next gt Name required m2mTak Address 2003 3 Secure communication key MySecureKey Autodownload Modem configuration X con The window M2M port properties will be displayed Set the connection parameters for the modem here The item Name is intended for user s de
44. value exceeds any alarm limit or if the binary input is in a state of active alarm the symbol will be displayed in front of the value This response message also includes alarm limits for measured values but not for binary inputs If a data logger Gxxxx is connected to the modem information about adjusted alarm delays in minutes for all measured values and binary inputs will be displayed too The response message example data logger Sxxxx or Rxxxx Logger Store_13 Temp 24 7C 19 0 26 0 Hum 45 5 RH 0 0 50 0 DP 12 1C 0 0 10 0 The response message example data logger Gxxxx Logger Store_13 Temp 24 7C 19 0 26 0 1m Temp2 25 0C 10 0 24 0 2m Binl OFF 1m Bin2 ON 10m values The command for reading of the current values and their alarm settings 12345678 1 24 7C 19 0 26 0 2 The current values and their alarm 45 5 RH 0 0 50 0 6 12 1C 0 0 10 0 settings from the data logger Sxxxx or RXXXX 12345678 1 24 7C 19 0 26 0 1m 2 The current values and their alarm 25 0C 10 0 24 0 2m 3 OFF 1m 4 ON settings from the data logger 10m GXXXX The logger is switched off A query can t be processed because the data logger is switched off An error occurred during communication A query can t be processed because with the logger a communication error between the modem and the data logger has occurred Data logger type detecting is still in A query can t be processed because progress please try it lat
45. y connected with negative pole of power supply Therefore it cannot be conductively connected with a vehicle chassis ground TE GPR LP040 07 4 Quick installation 4 1 Check of accessories Make sure you have available all accessories needed to operation the SIM card the GSM antenna the power supply adapter and the COM adapter IP65 or the connection cable kit according to the data logger the data logger the pay version of program for data loggers and access to the M2MTalk server service 1f you want to use it 4 2 Software installation Install the paid version of program for data loggers minimally the version 2 2 18 0 see also the page 7 on the computer from what you want to have access to the device The latest program version 1s available on www cometsystem cz Please follow instructions of the installer during installation process If you have activated GPRS data services you will use the GPRS connection for setting of the modem In this case installation of any others drivers is not needed If you want to set up the modem by using the setting cable via RS232 interface for example when you have not activated GPRS data services you must also install driver for GPRS modem configuration which is available on above web address too 4 3 The modem assembling 4 3 1 The SIM card You must have activated a GPRS data services if you want to communicate with the data logger remotely via GPRS If the modem and the data
46. y sending SMS message gsmstatus to the modem phone number A response delivery time is generally dependent on a momentary cellular network load and state If the modem works correctly it will send back SMS message with its state information If you don t receive the response to this SMS message please check your SIM card settings power supply connection and aerial connection If communication with the modem via cellular network is impossible you can try to find a problem with the program for data loggers In this case you must interconnect the modem and the computer via the setting cable see the chapter The setting cable QMS2901 on page amp 4 5 Setting up the modem If you don t intend to use remote communication with the data logger via GPRS you can go to the chapter Setting of the other parameters on page 15 4 5 1 Setting of GPRS connection parameters If you didn t specify the GPRS connection parameters before ordering the modem you must set it up now To do it you can send a special SMS message to the modem phone number The first word of the message must always be gprs After this keyword parameter values for an actual setting follows in specific order see below gprs apn user password dns If the trailing parameter values are not entered they will be deleted Don t enter the square brackets in the SMS message Individual items of the message must be separated by spaces For more detailed information about s

LP040 The instruction manual

Contents

Download Pdf Manuals

Related Search

Related Contents