Home

manual

1. 21 century world of ISDN R N IPAC 2AB 2 0 FIGURE 1 THE BIPAC 2AB 2 0 ISDN A B ADAPTOR Package Contents The BIPAC 2AB 2 0 package comes with the following accessories 1 The BIPAC 2AB 2 0 external ISDN a b adaptor 2 One RJ 45 cable Chapter 1 Introduction 3 One AC to DC power adaptor 4 This User s Manual BIPAC 2AB 2 0 Features The BIPAC 2AB 2 0 supports many standard and enhanced features that allow you to make full use of ISDN services with your existing analog devices including the following Caller ID Individual phone number MSN for each analog port Password protected for configurations Inter call Call waiting Call hold retrieve Internal call transfer Internal call forwarding Call suspend resume Supports keypad protocol for supplementary services Speed dialing Call filter Do not disturb Distinct ring pattern for different MSN Chapter 2 Before Connecting Make sure that you have all you need to connect the BIPAC 2AB 2 0 ISDN a b adaptor You should have the following 1 Atleastone analog telephone or other analog device 2 A power outlet that supplies 220 240 volts AC 3 An ISDN basic rate S interface released by PTT Post Telephone and Telegraph administration Connecting the BIPAC 2AB 2 0 Please refer to the following instructions and figures for installation procedures 1 Connect one or two analog telephones or other analog devices to the RJ 11
2. support billion com tw WWW http www billion com tw 13
3. the setting Id 1 4 Number Length lt 4 If Length 0 Clear the setting Id 1 4 Number Length lt 20 If Length 0 Clear the setting Restricted Number Number ial BIPAC 2AB 2 0 User s Manual 2 0 User s Manual 83 Pass Func Id Parameter Func Id 0 Ring unit parameter 01 99 0 15s Default is 10 1s Func Id 5 Hold Notice Parameter 00 99 Ring unit Default is 0 Func Id 1 3 MSN1 3 Func Id 4 Default Ring Pattern Func Id 6 Internal Ring Pattern Parameter x x2 1 lt x x lt 9 Ring Unit xj ring on x ring off Default is x1 1 x 4 Pass Func Id Flag Func Id 1 CLIR Flag 0 or null Disable Flag 1 Enable one time Flag 2 Enable always Func Id 2 No Call Waiting Func Id 3 Authority Setup Func Id 4 Call Filter Func Id 5 Internal Call Forwarding Flag 0 or null Disable Flag 1 Enable 81 Pass Funcld Flag Func Id 1 MIC Volume Flag 0 low 5 high Func Id 2 Speaker Volume Flag 0 low 4 high Shaded area can be ignored if the password is disabled The factory default password is 0000 Using the Telephone Functions With an analog telephone connected to the phone port of the ISDN TA you can avail of the following functions by using the number keys 0 9 the pound key and the star key Chapter 2 Using BIPAC 2AB 2 0 kl e External To make an external phone call dial the number as you would Calling with a regular phone system In
4. Artikel 3 1 b EN 55022 1998 Class B EN 61000 3 2 A12 1996 EN 61000 3 3 1995 IEC 61000 4 2 1995 IEC 61000 4 3 1995 LEC 61000 4 4 1995 LEC 61000 4 5 1995 IEC 61000 4 6 1996 IEC 61000 4 11 1994 Interface specification Termination point of a public telecom Network specification Schnittstellenspezifikation Netzabschluss eines ffentlichen TK Netzes Spezifikation TBR3 11 95 TBR3 A1 12 97 part of Ets 300 047 3 08 92 This declaration is issued by Diese Erkl rung wird verantwortlich abgegeben durch Place General Manager Billion Deutschland Table of Contents CHAPTER 1 1 Iniroduchons sneiai 1 An Overview of the BIPAC 2AB 2 0 i l Packape Contents aula lola 2 BIPAC 2AB 2 0 Features ele 3 CHAPTER 2 4 Using BIPAC 2AB 2 0 ira 4 Before Connecting sirena eu 4 Connecting the BIPAC 2AB 2 0 i 4 The Pront Panel EEDs uses es sang 5 Programming the BIPAC 2AB 2 0 Functions 6 Using the Telephone Functions carla ea 8 CHAPTER 3 12 Troubleshoo0tmg ira 12 Troubleshooting Procedures 12 Chapter 1 An Overview of the BIPAC 2AB 2 0 What is ISDN ISDN is an abbreviation for Integrated Services Digital Network ISDN transfers information digitally and integrates all telecommunication services such as telephone teletext videotex etc into a single network Using ISDN you can transfer text voice data files im
5. Billion BIPAC 2AB 2 0 ISDN a b Adaptor User s Manual Declaration of Conformity Konformit tserkl rung in accordance with the Radio and Telecommunications Terminal Equipment Act FTEG and Directive 1999 5 EC R amp TTE Directive gem dem Gesetz ber Funkanlagen und Telekommunikationsendeinrichtungen FTEG und der Richtlinie 1999 5 EG R amp TTE The Manufacturer Billion Electric Co Ltd Hersteller 8F No 192 Sec 2 Chung Hsing Rd Hsin Tien City Taipei Hsien Taiwan R 0 C declares that the product BIPAC 2AB V2 0 erklart dass das Produkt Telecommunications terminal equipment Telekommunikations Tk endeinrichtung Intended purpose ISDN a b Adaptor Verwendungszweck complies with the essential requirements of 3 and the other relevant provisions of the FTEG Article 3 of the R amp TTE Directive when used for its intended purpose bei bestimmungsgem er Verwendung den grundlegenden Anforderungen des 3 und den brigen einschl gigen Bestimmungen des FTEG Artikel 3 der R amp TTE entspricht Harmonised standards Health and Safety requirements contained in 3 1 1 Article 3 1 a Harmonisierte Normen Gesundheit und Sicherheit gem 3 1 1 Artikel 3 1 a EN 60950 1992 A1 1993 A2 1993 A3 1995 A4 1997 A11 1997 Harmonised standards Protection requirements with respect to EMC 3 1 2 Article 3 1 b Harmonisierte Normen Schutzanforderungen in Bezug auf die EMV 3 1 2
6. ages and even video Before the use of ISDN telecommunications operated using analog devices which limited the quality of telecommunication transfers With ISDN technology the telephone lines can transmit data digitally with much greater speed and clarity of transmission than with analog transmissions The ISDN is capable of transmitting all kinds of information at greatly accelerated rates A typical modem transmission has a rate of 56Kbps kilobits per second or thousand bits per second ISDN digital technology allows transfer rates of up to 128Kbps Because ISDN transmits data digitally the data is virtually error free and the transmission is much clearer with fewer interruptions and slowdowns in facsimile transmissions With ISDN devices implemented throughout the world a truly digital network will emerge allowing everyone fast and casy access to the global information highway BIPAC 2AB 2 0 User s Manual The BIPAC 2AB 2 0 ISDN a b Adaptor The BIPAC 2AB 2 0 ISDN a b adaptor allows you to make the transition from analog to digital without having to discard all your present analog devices The BIPAC 2AB 2 0 provides an interface between your ISDN line and present analog devices such as your telephone With a full array of convenient functions such as call waiting call holding call transfer call forwarding and speed dialing among others your BIPAC 2AB 2 0 will help you step from the world of analog communications right into the
7. e telephone number keys 0 9 the pound key and the star key NOTE You should hear 2 short tones if the programming is successful otherwise you will hear more than 6 tones indicating failure of programming Function k Second k Third Name Field Field y y Password Old New Pass 7 Setup Pass Password 97 Pass Flag SEEE disable password Enabling Flag 1 enable password Factory Pass Id 0 or null default setting Default 95 Pass Funcld Flag Func Id 1 PCM Law Flag 0 or null A Law Flag 1 u Law Func Id 2 Bearer capability Flag 0 or null 3 1kHz audio Flag 1 speech Flag 2 G3 Fax Func Id 3 Ring Signal Flag 0 or null 25Hz Flag 1 16Hz Flag 2 50 Hz Func Id 4 Not check in band tone Flag 0 or null disable Flag 1 enable Chapter 2 Using BIPAC 2AB 2 0 2 Using BIPAC 2AB 2 0 Parameter Func Id 0 Enabling Flag 0 or null disable Flag 1 enable Func Id 1 Caller ID Type Parameter 0 4 Func Id 2 Caller ID Country Parameter 0 99 Func Id 3 Date and Time Func Id 4 Call waiting Speed i 1 4 Func Id 5 Insert zero number Flag 0 or null disable Flag 1 enable Id 1 3 MSN1 MSN3 Number Length lt 20 If Length 0 Clear the setting Flag 0 or null Listen to all MSNs Flag 1 Listen to a specified MSNs Flag 2 Do not disturb Number Length lt 20 If Length 0 Clear the setting Dialing Number Length lt 24 Number If Length 0 Clear
8. jacks labeled a b 1 or a b 2 on the back of the BIPAC 2AB 2 0 Refer to Figure 2 2 Connect your ISDN line to the RJ 45 jack labeled ISDN So on the back of the BIPAC 2AB 2 0 Refer to Figure 2 3 Plug the power adaptor into the power outlet The POWER LED will illuminate on the front panel Chapter 2 Using BIPAC 2AB 2 0 ISDN So Power jack RJ 45 jack Phone ports FIGURE 2 CONNECTING THE BIPAC 2AB 2 0 4 The BIPAC 2AB 2 0 ISDN a b adaptor will run a Power On self diagnostic test The LEDs on the front panel will blink on and off one by one and the connected analog telephones will ring The Front Panel LEDs The following illustration and table describe the front panel LEDs FIGURE 3 THE FRONT PANEL LEDS LED Meaning e When lit it indicates AC power is connected RUN Flashes periodically to indicate that the BIPAC 2AB 2 0 is working properly BI B2 4 ISDN When lit it indicates that the ISDN SO bus is activated When lit it indicates that the ISDN B1 channel is being accessed It will flash during data transfer i When lit it indicates that the ISDN B2 channel is being accessed It will flash during data transfer E lr the Phone 1 port is in use When lit it indicates that the analog device connected to the Phone 2 port is in use BIPAC 2AB 2 0 User s Manual Programming the BIPAC 2AB 2 0 Functions The functions of BIPAC 2AB 2 0 are programmed by the use of th
9. l with the following command After you put the telephone handset on hook hang up the call will be transferred to the other port For two or more ISDN devices for example one ISDN a b adaptor and one ISDN phone connected to your ISDN line you can suspend a call on one device ISDN a b adaptor and resume the call on the other ISDN phone To suspend a call with the analog telephone connected to the ISDN a b adaptor enter this command xx Call ID Call ID is not required or any number up to 8 digits You can resume the suspended call when you use the command with the same Call ID Example If you receive a call in the living room and want to continue it in another room use this combination xx 12345 in the living room and hang up Go to the other room and enter the command again xx 12345 your call is resumed Chapter 2 Using BIPAC 2AB 2 0 Some telephone companies ISDN systems are using Keypad Protocol for activating deactivating some supplementary services such as external call forwarding To let the ISDN a b adaptor enter Keypad mode you can press 00 Then all the following keys and numbers will be sent out using Keypad Protocol Example If your telephone company give you a keypad command of 21 number to activate the external call forwarding function you can press 00 21 number to send out 2 number with Keypad Protocol After the keypad command is sen
10. t out all the incoming calls will be forwarded to the number 11 Chapter 3 Troubleshooting Procedures Possible Cause Remedy The B1 LED is The RAM is Consult your dealer always lit after defective power up The B2 LED is The ISDN chip is Consult your dealer always lit after defective power up No dial tone from 1 Can not 1 Ensure that the ISDN switch or activate So ISDN Sc line is PABX securely connected to the RJ 45 jack 2 No B channel Ensure no other available device is on the same Sc line and occupying the B channel Can not receive incoming call Can not have call waiting function Appendix A Product Support Possible Cause Incoming call s phone number does not match any a b port s phone number Do Not Disturb function has been enabled Call Forwarding function has been enabled Telephone company does not support this function Do Not Disturb function has been enabled Ensure that the phone number for each a b port is correctly configured Disable Do Not Disturb Disable Call Forwarding Check with your telephone company to see if it supports call waiting Disable Do Not Disturb If you continue to have problems you should contact the dealer where you bought this BIPAC 2AB 2 0 If you have any other questions you can contact Billion Electric Co Ltd directly at the following addresses Email
11. ter call or To make a call to the other analog port of the ISDN a b adaptor Internal you can press Calling Speed To dial any of the Speed Dialing numbers that you have Dialing programmed in use the following command x SID where ID is a number from 1 to 4 Example If the 4 speed dialing number is 5551113 the following combination 54 dials a call with the number 5551113 Redial To redial a number use the following command 01 Pick Up To answer an incoming call that is designated to the other analog port you can press 02 Make a New To disconnect an active call and then have the dial tone for Call making a new call to you can press 03 Hold To put an active call on hold use the following command line Retrieve e To retrieve a call that s been put on hold press the star key and pound key Disconnect To disconnect an active call and then retrieve a call that has been and then put on hold use the following command line Retrieve x0 BIPAC 2AB 2 0 User s Manual 10 Call Waiting Internal Call Transfer Suspend Resume If you have an active call and the Call Waiting function is enabled you will hear two tones when there is another incoming call You can switch between the two calls by using the Hold Retrieve function To transfer a call to the other analog port of the ISDN TA you can first put the call on hold by pressing x Then make an internal cal

manual

Contents

Download Pdf Manuals

Related Search

Related Contents