Home

POWER BACKUP CHARGE RATE TESTER USER MANUAL

1. Limited Warranty This product carries a 1 year limited warranty to the original purchaser on manufacturing faults The 12Volt lead acid battery located inside the unit carries a 3 month limited warranty The receipt proofing date of purchase and the product must be returned to a ONTARIO IMPORT AND EXPORT CC representative The warranty is void if the unit casing has been opened by any one else The warranty is also void when handled carelessly ONTARIO IMPORT AND EXPORT CC will not be held responsible for any damages on other products nor personal injury when using our products All Product and Printing detail CopyrightO Protected 2012 Page 5 Ordering Product Ordering Code Automotive power backup unit with build in alternator ONTCEPS12 charge rate testing feature Carbon Graphite 6000Watt ONTLT6000 12V Lead Acid Battery Load Tester Trolley for ONTLT6000 Load Tester ONTTROO1 www ontarioza com Page 6 All Product and Printing detail Copyright Protected 2012 Manufacturer Declaration Designer ONTARIO Designs a division of ONTARIO IMPORT AND EXPORT CC Manufacturer ONTARIO IMPORT AND EXPORT CC South Africa This product has been designed by a team with years experience in the lead acid battery retail and wholesale industry including electronic engineering The product is engineered to be robust and accurate for professional customer service The manufacturer tests calibrat
2. A division of ONTARIO IMPORT AND EXPORT CC Automotive POWER BACKUP and CHARGE RATE TESTER ONTCEPS12 Series USER MANUAL Website www ontarioza com All Product and Printing detail CopyrightO Protected 2012 Content Introduction rarnannvnnnanavnvnnnenannvnenenaveneenenene 1 Features end 1 Power Backup Procedures rrararnanarnanennr 2 Alternator Charge Rate Test Procedure 4 Trouble Shooting rrarrannnnrnnnnnvannannnnnarnnener 4 Maintenance x icsccnsntarneceneaeeaesicy eeenarnasatanaeeens 4 Safety Instructions rrarrnrnrrnarnrvnrvnrnernennere 4 Technical Specifications rrrrarrnnnrrnvnerevnnrn 5 Limited Warranty cccccecscceeeeeeeeeeeeeeees D Ordering EE 6 Manufacturer Declaration cecceeeeees 14 Support and Contact Information T All Product and Printing detail Copyright Protected 2012 Introduction With the advances on the electronic systems for automotive vehicles it is a precautionary measure to back up vehicle power when performing battery fitments and replacements Failure to perform this procedure may cause the vehicle to have electronic memory loss including radio setup window position calibration and alarm program The ONTCEPS12 series is used to back up automotive vehicle power when performing battery installations It also functions as an alternator charge rate tester Features 1 Handy Box Unit with Isola
3. 2 All Product and Printing detail Copyright Protected 2012 Clamp Connections on Battery Terminals JER Black Switch the unit power switch to the Off position before connecting Failure to perform this procedure may cause an electric spark Clean the terminals on the vehicle battery Place the positive red clamp jaw around the back side of the positive terminal allowing access to loosen the terminal nut Place the negative black clamp jaw around the back side of the negative terminal allowing access to loosen the terminal nut The negative black clamp jaw can also be clamped on the chassis The standard Backup procedure can now be performed as stipulated in point 2 below 2 Backup Switch off the vehicle ignition and lights With the clamps connected refer Clamp Connections the needle on the Voltage panel meter should indicate a positive voltage detected from the battery to be replaced If not check the clamp connections Dirt can be cleared with scratching back and forth motions to the clamps Check the protection fuse on the unit If blown replace with 10 15 amp blade fuse Switch the unit power switch to the ON position The unit will now backup the vehicle power Discontent the automotive battery terminals Note1 The needle on the Voltage panel should stay above 10Volt If not the unit was not switched on Note2 The positive automotive battery terminal must not touch any neg
4. ative chassis point of the vehicle during this procedure Remove the automotive battery from the vehicle and fit replacement battery Connect the battery terminals on the replacement battery again Switch the unit power switch to the Off position as the process is complete If required the Alternator Charge Rate Test Procedure can be done refer Alternator Charge Rate Test Procedure If not disconnect the clamps Page 3 All Product and Printing detail Copyright Protected 2012 Alternator Charge Rate Test Procedure With the clamps connected refer Clamp Connections on Battery Terminals and the unit power switch to the Off position start the vehicle Increase the revolutions to 2000 r p m The needle on the Alternator panel meter should stay between 13 8 Volt and 14 2 Volt Repeat test with vehicle main lights switched on Note A bottom buffer on the Alternator graph has been added for alternators with lower performance A top buffer on the Alternator graph has been added for new calcium calcium high charging specifications alternators that charge up to 14 5V Use own discretion Trouble shooting e Voltage panel meters do not detect any voltage 1 Check protection fuse on unit If blown replace with 10 15 amp blade fuse 2 Clean the automotive battery terminals and the units clamps Check the clamp connections Dirt can also be cleared with scratching back and forth motions when the clamps are co
5. es and approves all products to high standards Support and Contact Information ONTARIO IMPORT AND EXPORT CC offers professional customer support www ontarioza com gt Y ONTARIO Import and Export Director Petrus Jacobus Nel Electronic Engineer B Eng ONTARIO IMPORT AND EXPORT CC Page 7 All Product and Printing detail CopyrightO Protected 2012
6. n the Off position before making connections e Do not perform replace a hot automotive battery with a hissing sound from excessive gassing e A unit with damaged cables should not be used Repairs should be performed by a ONTARIO IMPORT AND EXPORT CC representative e Always use protective gear including safety glasses when working with lead acid batteries e Batteries emit explosive gas Never smoke or allow open sparks near the vicinity of the battery e Lead acid battery acid is corrosive If acid come into contact with eyes rinse with fresh water and seek immediate medical advice e Allow sufficient ventilation when using the unit e This product should not be used by children Page 4 All Product and Printing detail Copyright Protected 2012 Technical Specirications Model ONTCEPS12 Rated Input Voltage 0 15Vdc 20Vdc max for 20 seconds Rated Reverse Voltage Do not operate in this mode 15Vdc for 5 seconds Alternator test resolution 0 1V Internal Battery Type 12Volt 7Amp Hour valve regulated lead acid Internal Battery Rated Charge 14 5Volt max 2 2Amp max Dimensions on casing 158mm x 116mm x 148mm LxWxH Indicators Panel Meters Analogue wide view Dimension on Panel Meter View Area 69mm x 34mm LxH Clamp Cable length 1 Meters Clamp Grasp Displacement 24 mm Protection Fuse 10 15Amp blade Weight Including internal Battery 3 2 Kg
7. nnected to the battery terminals If problem persists send product to nearest sales representative for repairs e Voltage panel meter needle shifts to the incorrect left negative side Reverse polarity e Panel meter needles not on zero point Send product to nearest sales representative Maintenance e Keep the 12Volt lead acid battery located inside the unit charged The charge state can be checked by switching the unit power switch to the ON position The Voltage panel meter red bar indicates that charging is required Connect a 12Volt lead acid battery chargers clamps directly to the units clamps on and on Switch the unit power switch to the ON position to initiate charging The Alternator panel meter will indicate the charge voltage e Replace the 12Volt lead acid battery located inside the unit every 2 to 3 years or when faulty A nearest sales representative may perform repairs if soldering skills are required The clamps on the unit should be kept clean with a solution of hot water and bicarbonate of soda Do not let the inner components come into contact with water The casing and panel meters may be cleaned with a soft damp cloth Do not drop the unit onto hard services or let it fall This may cause damage and void the warranty Sarety Instructions e The ONTCEPS12 is designed for 12Volt automotive vehicles Do dot use the unit for any other purpose e Always make sure the units power switch is i
8. ted Clamping Points and Rubber Base With the non slip rubber base the unit can be placed on any surface including the engine bay Isolated clamping points provides safe storage for clamps Isolated Clamp in _ Rubber Base 2 Flush Panel Meters The panel meters fit flush into the unit This minimizes damage to the meters 3 Clear Wide View Self Explanatory Graphs Two Copyright protected graphs ensures reliability backups and accurate alternator charge rate tests 5 70 35 14 7 iden 0 man 9 AS 4 il I N s Bren 7 NS amp Ss v Ae V ONTARIO V ONTARIO DESIGNS DESIGNS O a O O O Page 1 All Product and Printing detail Copyright Protected 2012 Power Backup Procedures 1 Clamp Connections Note Do not use cigarette power points on vehicles as a backup access points These connections may have protective circuitry that will prevent reversed inputs Clamp Connections on Jump Start Points Switch the unit power switch to the Off position before connecting Failure to perform this procedure may cause an electric spark Clean the jump start points on the vehicle Place the red clamp jaw around positive jump start point Place the negative black clamp jaw around the negative jump Start point or the chassis The standard Backup procedure can now be performed as stipulated in point 2 below Red Black Page

POWER BACKUP CHARGE RATE TESTER USER MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents