Ilumipod Inground IP Series User Manual Rev. 4
Contents
1. If you still experience technical problems after trying the solutions in the Troubleshooting Guide contact ILUMINARC Technical Support Product Maintenance To maintain optimum performance and minimize wear the user should clean the Ilumipod Inground IP products frequently Usage and environment are contributing factors in determining the cleaning frequency As a rule the user should clean the products at least twice a month Dust and grime build up on the glass surface reduces light output performance To clean an Ilumipod Inground IP product follow the below recommendations 1 Disconnect the power to the product 2 Wait until the product is cold 3 Loosen the Allen bolts on the stainless steel collar by turning them CCW not more than a turn or two enough to release the aluminum latch from its locked position 4 Pull the product out of the installation sleeve making sure that you are not pulling the signal or AC power cables 5 Use a wet vacuum cleaner to remove any liquid inside the installation sleeve and around the product s housing Inspect the cables and the gland nuts for signs of deterioration Clean or unclog the water drainage Replace the product in the installation sleeve ODZEW A Reattach the product to the installation sleeve by turning the Allen bolts CW You should only need a turn or two to have the stainless steel collar firmly attached 10 Clean the glass surface with a mild solu2. Green 3 Data Red m L LUN maaa ann 7 777 _____ poe signal Juicios cian a u box Conduit or DBC box llumipod Inground IP Series User Manual Rev 4 ILUMINARC If you have not configured the DMX starting address and DMX mode for each product they will all use their default values This means that all products will operate in unison Refer to the D Operation chapter to learn how to enable the Ilumipod Inground IP products to operate with the ILUMICON controller llumipod Inground IP Series User Manual Rev 4 Controllers The products in the Ilumipod Inground IP Series can operate with a standard DMX controller the ILUMICON controller or the Ilumicode controller The sections below will show you how to connect these products to the corresponding controllers The instructions to operate these products with each of the above controllers are in the Operation chapter of this manual DMX Controller The Ilumipod Inground IP products can work with a standard DMX controller The channel assignments will depend on the chosen personality see the corresponding Menu Map on pages 11 and 12 and the DMX address assigned to each product see Programming on page 13 The figure below illustrates how to connect the DMX controller to the Ilumipod Inground IP products To OOOOOOOO th C uns DMX512 A Controller ILUMICON The Ilumipod Inground IP Tri a
3. lenses Product order code 11036010 30 lenses Product order code 11036008 llumipod Inground 36 IP RGB Features Operating modes 1 channel Dimmer 3 channel RGB control 4 channel RGB dimmer 6 channel RGB per module 7 channel RGB dimmer macro strobe dimming speed High power I W 750 mA Red Green and Blue LEDs Blackout static dimmer strobe pulse Installed non changeable optical system 15 lenses Product order code 11036009 30 lenses Product order code 11036007 llumipod Inground Tri 12 IP Features Operating modes 1 channel Dimmer 3 channel RGB control 4 channel RGB dimmer 6 channel RGB per module 7 channel RGB dimmer macro strobe dimming speed High power 3 W 1 050 mA tri color LEDs Blackout static dimmer strobe pulse Installed non changeable optical system 16 lenses Product order code 11012001 Product Description ILUMINARG Product Dimensions All Ilumipod Inground IP Series models 4 llumipod Inground IP Series User Manual Rev 4 ILUIMIINABHC 3 Installation Always keep the power cables away from the signal cables by running them in different conduits and using separate distribution boxes The llumipod Inground IP products can support a distributed load of up to 3 000 kg 6 614 lbs when properly installed llumipod Inground IP Series User Manual Rev 4 Installation Notes The Ilumipod Inground IP products consist o
4. Goto SETTINGS gt COLOR 2 Select the color method OFF RGBTOW or UC Color Description When the RGB faders are all at 255 the output is at its maximum When the RGB faders are all at 255 the output is the OFF BERTO W selected white color see Color Calibration When the RGB faders are all at 255 the output matches the UC same color output of previous versions of this product Reset Only for 36 IP RGB and Tri 12 IP 1 Goto SETTINGS gt RESET TO FACTORY SETTINGS 2 Select an option YES NO llumipod Inground IP Series User Manual Rev 4 j IF LIE 1 i Lo A Tus DMX Values ARC 1 Channel Function Value Percent Setting 1 Red 0006 255 0 100 2 Green 0000 255 0 100 3 Blue 000 U 255 0 100 ARC 1 D Channel Function Value Percent Setting 1 Dimmer 1000 255 0 100 2 Red 0000 25510 100 3 Gren 000 25510 100 4 Blue 000 U 255 0 100 ARC FULL Channel Function Value Percent Setting 1 Dimmer 1000 255 0 100 2 Red 0000 25510 100 3 Gren 0000 25510 100 4 Bue 0000 25510 100 Green Up Green 100 Green 100 Green Down U 110 Red Up Green 0 130 Red 100 Green 0 150 Red 100 Green Up Green Down Green 100 205 White 1 3 200 K 206 U 210 White 2 3 400 K 211 215 White 3 4 200 K 216 220 White 4 4 900 K 221 U 225 White 5 5 600 K 226 U 230 White 6 5 900 K 231 U 235 White 7 6 500
5. 12 Cool White and 24 Warm White Construction FIOUSTIEO patadas acacia Cast aluminum body and stainless steel outer ring A A O O E ika Black body and silver outer ring LE COVEI TNA Impact resistant drive over rated Ingress Droteckon IP 131 nen FAO IP67 Photometrics IH La I ee ee ee 15 A en T TEE 13 1 BSS PR TP 28 0 MIGMINANCE oco oc JO on O O III 226 75 fc 6 ft Thermal Maximum ambient temperature eii ertet OE UO A LEPEGO 113 F 45 C ofe LILO EEEE EA Natural convection Control amp Programming Add y AE A O O LR Ilumicode DA PU PROPRE ne ee Terminal strip in sealed junction box Data piti configuration u a Pin I shield pin 2 pin 3 TOTO COS NN RT ee OE OE USITT DMX512 A DMA CHMOD ar EA taa 1 2 0r3 Ordering Information Ilumipod Inground 36 IP Optic 19 VW een ea 11036010 Ilumipod Inground 36 IP Optic 30 VW oo occcccnnncccuauanocononnnnncnnnnnnonononononnnnoncnnnnnnnananononnnnnoss 11036008 Warranty Information YY EI APEE I PE ATB W M 2 year limited warranty WERTE CONFORMS TO y UL STD 1573 CERTIFIED TO 5 US CSASTD C22 2 LiSTEO No 166 3144482 llumipod Inground IP Series User Manual Rev 4 27 i I Technical Information I LUMINARC llumipod Inground 36 IP RGB Weight amp Dimensions BOZE ZEP ANNC 12 6 in 320 mm Ei Na sacri NN 5 7 in 146 mm bI WERE aa WRACAC ORA OOOO 17 6 lbs 8 kg Power A O 100 240 VAC 50 60 Hz Power consumpHon T20 V ua its 38 W 0 6 A Power
6. IP67 rating when fully adjusted AC Power Input Voltage and Frequency The products in the Ilumipod Inground IP Series have an auto ranging power supply with an input voltage range of 100 240 VAC 50 60 Hz Power Consumption To determine the power requirements for any of the Ilumipod Inground IP products see the label affixed to the side of the product Alternatively you may refer to the corresponding specifications chart in the Technical Information chapter of this manual Junction Box Wiring The Ilumipod Inground IP products have an IP67 rated junction box where the power and signal cables come into the unit The cables access the junction box through individual signal and power IP67 rated stainless steel gland nuts Make sure that the junction seal is clean before placing the cover back on In addition tighten the gland nuts and the junction cover to prevent water from entering the junction box and causing a short The figure below shows the connections in the junction box Data GND Live Black Black Data Ground Green Green Data Neutral Red White Power Wiring To provide AC power for any of the Ilumipod Inground IP products you must run a single SJTW rated 3 conductor cable AWG18 3 6 8 mm external diameter from the power distribution box into the installation sleeve and the product s junction box gt Strip the end of the AC power cable that will connect to the junction box as indica
7. K 236 U 240 White 8 7 200 K 241 U 245 White 9 8 000 K 246 U 250 White 10 8 500 K 251 255 White 11 10 000 K 005 U 255 0 20 Hz 000 009 Dimmer is set by Ilumicode 010 U 029 OFF Dimmer is linear 030 U 069 DIMI Fastest dimmer curve 070 U 129 DIM2 130U 189 DIM3 190 U 255 DIM4 Slowest dimmer curve 5 Color Macro White Balance 7 Dimming Speed llumipod Inground IP Series User Manual Rev 4 Operation Blue 0 Blue 0 Blue Up Blue 100 Blue 100 Blue Down Blue Up Blue 100 Blue 100 q i 1 m ra j HA NE em I F E 3 t R fi ta i j 4 F Y 74 LV d m I E AJ if A u Bu E Operation ILUIVIII SPECIAL 1 Channel Function Value Percent Setting 1 Module 1 Red 000 U 25510 100 2 Module 1 Green 000 U 25510 100 3 Module 1 Blue 000 U 25510 100 4 Module 2 Red 000 U 25510 100 5 Module 2 Green 000 U 25510 100 6 Module 2 Blue 000 U 25510 100 VW Channel Function Value Percent Setting 1 WarmWhite 000 255 0 100 2 Cool White 000 U 25510 100 VW D Channel Function Value Percent Setting 1 Dimmer 0000 255 0 100 2 WarmWhite 000 255 0 100 3 Cool White 000 U 25510 100 SOLID Channel Function Value Percent Setting 1 Dimmer 000 U 25510 100 16 llumipod Inground IP Series User Manual Rev 4 ARG Technical Information 5 Technical Information Always dry the optic surfaces carefully after cleaning them
8. below Replace the glass and then re silicone the seal to insure a watertight seal Replace the stainless steel collar making sure to align it with the Allen screws and while keeping the glass surface flush with the collar Replace all six nuts and adjust them manually until they touch the housing Tighten the nuts uniformly by alternating between opposite nuts Reattach the product to the installation sleeve by turning the Allen bolts CW You should only need a turn or two to have the stainless steel collar firmly attached llumipod Inground IP Series User Manual Rev 4 LUMINARC Make sure to AN connect the llumipod Inground IP product to a power line with the proper voltage and frequency as per the specifications in this manual or on the product s sticker The listed current rating indicates the maximum current draw during normal operation Always connect the llumipod Inground IP products to protected circuits CB or fuse with an appropriate electrical ground to avoid the risk of electrocution or fire Never connect an llumipod Inground IP product to a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel serves only as a 0 to 100 switch Make sure to use power and signal cables with the indicated outer diameters to ensure that the corresponding gland nut makes full contact with the cable s external insulation This is required to keep the product s
9. distribution modification or printing of this manual or its content for any other purpose without its written consent Document Printing For better results print this document in color on letter size paper 8 5 x 11 inches double sided If using A4 paper 210 x 297 mm configure your printer to scale the content of this document to A4 paper Intended Audience Any person in charge of installing operating and or maintaining any of these products should read the Guide that shipped with it and this manual in their entirety before installing operating or maintaining the product Disclaimer ILUMINARC believes that the information contained in this manual is accurate in all respects However ILUMINARC assumes no responsibility for any error or omissions in this document ILUMINARC reserves the right to revise this document and to make changes from time to time in the content hereof without obligation of ILUMINARC to notify any person or company of such revision or changes This does not constitute in any way a commitment by ILUMINARC to make such changes ILUMINARC may issue a revision of this manual or a new edition of it to incorporate such changes Document Revision The llumipod Inground IP Series User Manual Rev 4 supersedes all previous versions of this manual Please discard any older versions of this manual you may have whether in printed or electronic format and replace them with this version llumipod Inground I
10. IFIED TO B US CSASTD C222 LISTED No 166 3144482 28 llumipod Inground IP Series User Manual Rev 4 gt u F1 n FIN A m s LUMINARC Technical Information llumipod Inground Tri 12 IP Weight amp Dimensions GENSAT T OOO GORACO 12 6 in 320 mm uie OU cad T 5 7 in 146 mm NU a kz ANO O O DR DECRETA 17 6 lbs 8 kg Power AUTO TANSINS 20s esee beet nee 100 240 V AC 50 60 Hz Power CONSUINPIION 120V tao 38 W 0 6 A Power consumption a 230 Noo dase tern do oO 40 W 0 3 A Tnrush eurrent suse rot e imu ve Loa ER cap E ree oo OE ceases 0 1 A 120 V 0 3 A 230 V Power Connectors zo AA a Terminal strip in sealed junction box Light Source TYPE aa aaa AA 3 W 1 050 mA 50 000 hrs Tri color LEDs CONO tad dosis 12 Tri color LEDs Construction La SAA ee Cast aluminum body and stainless steel outer ring Col P Black body and silver outer ring LenS COV CL AA een Impact resistant drive over rated Ingress protection IP tatii aaa a LI a IP67 Photometrics IN 21 Weed ODIO S ee entre O 16 Beam anole ZR ZYTA 18 3 Field ALN nn nen eier 33 1 MAA JdX qv 225 lx 5m Thermal Maximum ambient temperature cccccncncccnnnnnnnnnonnnnnnnnnnnnnnnnnnonononnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnos 113 F 45 C A R a Mery went ee re neh erence rere ee Natural convection Control amp Programming AU ai ia OO psc han Sa uaa ad EO OWE DAEWOO Ilumicode Data Put unseren Terminal strip in sealed
11. Ilumipod Inground IP Series User Manual llumipod Inground 36 IP VW llumipod Inground 36 IP RGB llumipod Inground Tri 12 IP Edition Notes R FA In AI A Pape IVINARCG ILUMINI Edition Notes The llumipod Inground IP Series User Manual Rev 4 covers the description safety precautions installation programming operation and maintenance of the llumipod Inground 36 IP RGB Ilumipod Inground 36 IP VW and llumipod Inground Tri 12 IP products ILUMINARC released this edition of the Ilumipod Inground IP Series User Manual Rev 4 in May 2015 Trademarks The ILUMINARC logo the ILUMINARC name and all other trademarks in this document related to services or products by ILUMINARC are trademarks owned or licensed by ILUMINARC its affiliates or subsidiaries Any other product names logos brands company names or trademarks featured or referred to within this document are the property of their respective trademark holders Copyright Notice The entire content of this document except where applicable and unless otherwise noted is solely owned by ILUMINARC a wholly owned trademark of Chauvet amp Sons Inc Copyright 2015 ILUMINARC All rights reserved Electronically published by ILUMINARC in the United States of America Manual Usage ILUMINARC authorizes its customers to download and print this manual for professional information purposes only ILUMINARC expressly prohibits the usage copy storage
12. Ilumipod Inground IP products 1 Goto DIMMER 2 Select a dimmer curve OFF or DIM1 4 DIMMER Description OFF Dimmer curve is linear with fader DIM1 Non linear fastest DIM2 Non linear fast DIM3 Non linear slow DIM4 Non linear slowest llumipod Inground IP Series User Manual Rev 4 13 Operation Do not connect D any other controller to the product s when using the ILUMICON controller WHITE 1 11 define the white color shown when selecting a value 201 255 in channel 5 for the ARC FULL personality RGBTOW 22 defines the white A color shown when the COLOR value is set to RGBTOW 3 i IA mi 7 D gr h ILUMINARE A VIII WZAE BL ILUMICON Control Only for 36 IP RGB and Tri 12 IP 1 Goto PERSON 2 Select the REMOTE personality Static Color Only for 36 IP RGB and Tri 12 IP 1 GotoSTATIC 2 Select a color RED GREN or BLUE 3 Select a color value 000 255 4 Select STRB 5 Select a strobe frequency 0 20 Only for 36 IP VW 1 Goto STATIC 2 Select a color COOL or WARM 3 Select a color value 000 255 Color Calibration Only for 36 IP RGB and Tri 12 IP 1 Goto CALIB 2 Select a white color WHITE 1 11 or RGBTOW 3 Select an RGB color RED GREN or BLUE 4 Select a color value 0 255 5 Repeat steps 3 and 4 for the other RGB colors to obtain a white color 6 Repeat steps 2 to 5 for the other white colors Color Only for 36 IP RGB and Tri 12 IP 1
13. P Series User Manual i IV AIL A T irme ILUMINARG Table of Contents Table of Contents 1 INIrOQUCLONn a en 1 Wats IH te PA o mU ehe 1 Unpacking Instructions ccccccoonnccnnccccnnconnconnnncnnnnononnnnnonononnnnnnnnnnnrnnnonnnnnrnnnnnnnnnrancnnnnns 1 IE CONVENIOS E m T T T t 1 oalet NOIE S PP e sabe nce IN TEE 2 Personah Galely dO EEE A O OWE 2 MOURUBO GIG INSIallalon 22 2 4 deos tuuc so Coda iuo Da i buda Coda da Bep aes hse duas ose 2 POWER QAO MINO aa 2 OPEN ea cet tits OO ico 2 2 PFOQUCE DESERIPLON a aa 3 Common Feallies nn 3 llumipod Inground 36 IP VW Features eiiis agar anna a 3 Humipod Inground 36 IP RGB Features i teri vot beta tn ia dad be hoses 3 fi umipod Inground Tri 12 1P Fealures ae o A A ua eoa ea 3 Product Dimensions ccccecccceececseeeeceeeeeceeeeeceeeeesacessuueesaueeeseeeeesaeessaueesseeessneeesaaees 4 3 rris i 5 Installation IN OLS P Em 5 Installation Sleeve Orientation eose aiee e E E E EEA R 5 Installation Sleeve SOU Eb rer A einen wee 5 BEAM ANGIE AQLUSIMERE ne een 6 AC POW A ee ee see ee ensure 7 Input Voltage and ELFO QUEEN CV tas ee 7 POWERCORSUMIDNOMN se an een AEO OOO A AA 7 JUNelON BOoX Wiringe news ee ea 7 POWER VINNI 2 T 7 SIGNAL 44101810 esi tb I cH EK ABA to EP 8 Extena VV ICING iodo asi 8 POWER ISTO Oli eo EE 8 A E 8 Controle rr eT 9 DMA CODIIOWOE aiw basate e EET dE 9 IEUMIG ON soca ee een i WWP ae A
14. P gt DOWN POWER Menu Map Function Exits from the current menu or function Enables the currently displayed menu or sets the currently selected value into the selected function Navigates upwards through the menu list and increases the numeric value when in a function Navigates downwards through the menu list and decreases the numeric value when in a function O Turns the unit on The unit will turn off automatically UP after 30 seconds of inactivity gt MENU ENTER DOWN The products in the Ilumipod Inground IP Series have distinct menu maps based on the colors they produce whether RGB or White The Ilumicode controller presents the functions for both types of products White Functions Menu Map Ilumipod Inground 36 IP VW This menu map shows you which parameters of the Ilumicode controller correspond to the Ilumipod Inground 36 IP VW product When you scroll through the menu options you will see many of them that do not correspond with this menu map Skip them as they do not work with the White output products DMX PERSON DIMMER STATIC If you scroll after STRB you will see the RED GREN BLUE and AMBE colors Just skip them as they do not work with the VW products llumipod Inground IP Series User Manual Rev 4 Main Level Programming Levels Description N A Sets the DMX starting address 3 channel SpectraWhite control N A 4 channel SpectraWhite contr
15. R A 9 lumi COO PORZE RENEE 10 4 ODETAUO a E 11 WUTC OGG Peer c TM 11 Humicode Panel Desorption Z eoa teo o ed teo ouam e ee ae 11 MENU B Ir lo wadi die aha T O PM rM THEE 11 White F nctions Menpu MAD ae ad GE EI dias 11 RGB FURCTONS MENU Map enio A tecto Heer 12 Programimi een can tud a ot da 13 DMA PEISONANY m T M 13 DMX Starting Address seien 13 Bess Mcr 13 ILUMIGON CONTOU ziei E 14 Ac ENER 14 Selle eile ci Di A Dia 14 Bom cc 14 acd P C uH Emp 14 BUS m REN 15 A iO 15 AR Tu eut EEE uU LUE opt dE p LI UN 15 ARCRULL z e 15 SPECAG T estos toch x Beggs eed See weak case ae 16 llumipod Inground IP Series User Manual Rev 4 i Table of Contents LUMINARC Year ea ae M P 16 Va Daci t een ae PRECZ Acid ME 16 GAP M a 16 95 Technical INTORMANON pee 17 Pr dLiCEMainienancowa ak oda dba 17 Product REDAS GG GiG aaa 17 Troubleshooting Gulden E 18 Exploded VIEW Pic 19 PNOIOMEINES rain 20 Humipod Inground 36 IP 15 VW ae a debane 20 fipmipod Inground S6 IFSOP VW een td it as 21 llumipod Inground 36 IP TOS RGB s ue anne ua 22 Numipod Inground 86 17 30 RGB acea a 23 HUMIBOA INGIOURG THAT D 1O EE 24 LEDIDISCGAIMEN a T US 25 IUE PORE SN E 25 PN TREES 25 Color Rendering Index CHI tinea id a cau
16. SET NO YES Resets unit to factory default settings 12 llumipod Inground IP Series User Manual Rev 4 Operation Programming Carry out all the programming procedures indicated below from Ilumicode s panel Refer to the corresponding Menu Map pages 11 and 12 to learn how the menu options relate to each other depending on the type of product Make curas Use lt ENTER gt and lt MENU gt to change levels in the Menu Map This is equivalent to moving D press ENTER rght and left respectively Use UP and DOWN to move forward and backwards after selecting an respectively within the Menu Map options option Otherwise the product will not save the Press ENTER to accept the selected value for an option This will send that value to the new setting In this case product s the llumicode s display will show SEND DMX Personality All Ilumipod Inground IP products 1 Goto PERSON and select any DMX personality that matches the product with which you are working ignore any other options 36 IP RGB amp Tri 12 IP 36 IP VW ARCI ARC D ARC FULL SOLID SOLID SPECIALI VW VW D 2 Make sure to arrange the DMX addresses of all products in the current DMX universe to avoid address overlapping The DMX Starting Address setting DMX Starting Address works with all but the REMOTE personality All Ilumipod Inground IP products 1 Goto DMX 2 Select a starting DMX address 001 512 Dimmer All
17. UMINARC Ilumipod Inground Tri 12 IP Optic 16 RGB 12 Tri color 1 lamp s rated Lumens lamp 1380 5 633 6 at Horizontal 0 Vertical O 17 6 Point 2009 ALL Iluminarc R amp D Optics Laboratory Type B Direct Full Cutoff Polar Candela Distribution 180 170 160 1507 14 5 700 4 750 3 800 tod 1102 350 100 CD 0 350 1 900 2 850 3 800 4 750 5 700 M 07H M 90H zmia m TE a WA DP Li 180 H Lu 270 H u 45 H 10 20 30 m Lumens Vertical Spread 34 2 Horizontal Spread Beam 50 Total 49 2 679 1 18 4 Illuminance at a Distance Distance Center Beam Vertical Beam Width Horizontal Beam Width ft fc ft ft Photometrics 3 625 96 I 0 Pro 1 3 2 6 156 49 1 9 2008 by 9 69 55 2 9 2 9 jSolutions Inc 12 39 12 3 9 Reported data calculated 15 25 04 4 8 from manufacturer s data file based on IES 18 17 39 5 8 recommended methods Vertical Spread 18 4 Horizontal Spread 18 3 24 llumipod Inground IP Series User Manual Rev 4 i m mot rf A ge l pl a m gl il m 1 p m ILUIVIII NAF Lo Technical Information LED Disclaimer LED Life ILUMINARC rates LED lifetime based on lumen depreciation of 70 of the original output with data provided by the manufacturer of the LED Data from the manufacturer of the LED are not independently verified or measured by ILUMINARC When the product is operating in optimal environmental conditions the LED li
18. VW Filename Manufacturer Luminaire Lamp Lamp Output Max Candela Input Wattage Luminous Opening Test Test Lab Photometry CIE Class Cutoff Class Ilumipod Inground 36 IP Optic 30 VW 100 ALL ILUMINARC Ilumipod Inground 36 IP Optic 30 VW 24 Warm White 12 Cool White 1 lamp s rated Lumens lamp 3000 3 534 3 at Horizontal 0 Vertical O 46 5 Point 2009 ALL Iluminarc R amp D Optics Laboratory Type B Direct Full Cutoff Polar Candela Distribution 2 600 150 170 160 1509 1409 13P 1 800 1 200 2109 LD O 8 gge 1 200 1 500 2 400 2 000 3 600 JU nm Vie 10 ar XP a E 45 H Flood Summary Efficiency Lumens Horizontal Spread Vertical Spread Field 10 27 3 819 3 322 52 7 Beam 50 13 8 413 5 26 6 Total 32 8 985 2 Illuminance at a Distance Distance Center Beam Vertical Beam Width Horizontal Beam Width ft fc ft ft Prolomelv s 3 392 70 1 4 1 4 Pro 1 3 2 6 98 18 2 8 2008 by 9 43 63 4 2 4 2 jSolutions Inc Reported data calculated from manufacturer s data file based on IES recommended methods 12 24 54 5 6 15 15 71 7 1 18 10 91 8 5 Vertical Spread 26 6 Horizontal Spread 26 5 llumipod Inground IP Series User Manual Rev 4 21 Technical Information EFA ILUMINARC llumipod Inground 36 IP 15 RGB Filename Manufacturer Luminaire Lamp Lamp Output Max Candela Input Wattage Luminous Opening Te
19. c Two or more LEDs do not work Faulty LED module Return for service to Iluminarc on a single module Faulty LED driver Return for service to Iluminarc The wrong LEDs light up when Change the personality using DMX Change the DMX address Circuit breaker fuse keeps Excessive circuit load Check total load on electrical circuit tripping blowing Check for a short in the electrical wiring Change DMX address Damaged DMX cables Check DMX cables Check polarity switch settings on the al does not respond to Wrong polarity on the controller sonde Loose DMX cables Check cable connections Faulty DMX interface Return for service to Iluminarc Faulty Display Main board Non DMX cables Use only DMX compatible cables Unstable control signals Install terminator as suggested ass babe Here Install an optically coupled DMX splitter DMX signal problems S 8 right after the product with the strong signal Install an optically coupled DMX splitter Too many products after unit 32 or before Keep DMX cables separated from power Interference from AC wires cables or fluorescent black lights 18 llumipod Inground IP Series User Manual Rev 4 Exploded View Reference Description Inner housing Installation sleeve 1 Stainless steel cover 2 15 mm tempered glass BE SOOD S 3 Diaphragm See eae e zm 4 LED lens panels Im T 5 LED boards m 6 Heat sink 7 Power supply 8 Control board 9 10 11 Dustproof board llumi
20. consumption 230 Virada 40 W 0 3 A as A II eingehen ee 0 1 A 120 V 0 3 AQ 230 V Power COMIC CHO rise Terminal strip in sealed junction box Light Source Aj 0 A CAN A 1 W 350 mA 50 000 hrs LEDs CO IEMANOR arado 36 LEDs 12 Red 12 Green and 12 Blue Construction EIGUSIRE arcade Cast aluminum body and stainless steel outer ring COIDE wata ee ee Black body and silver outer ring Lens COUPE is Impact resistant drive over rated Ingress protechon IP TAE aio uto cobre Eam OLE RAEE LO GA ON RENE GR IP67 Photometrics sled ODIOS m e diate 15 Bonm Eu io MEME NT 13 1 FCN AMS AWR 40 3 MOMANT AAA A PER pel Odes CE 226 75 fc 6 ft Thermal Maxima ambient TOR pe PAU Ca da nee 113 F 45 C oeil NRI Natural convection Control amp Programming SPR SS TIT ETE CONO TT TT TUO Ilumicode A S Terminal strip in sealed junction box Data pin configuration oooncccccnnnnncnnnnnnnnnononnnnnnnnnnnnnnnnnnnnnnonnnnnaninenennos Pin 1 shield pin 2 pin 3 Pro MN A USITT DMX512 A DMA BIS NR 1 3 4 6 or 7 Ordering Information Ilumipod Inground 36 IP Optic 15 RGB cccccnnnnonananononanonononcnonnnnnnnnnonnnnnnnnccnnnnnnanannn nro 11036009 Ilumipod Inground 36 IP Optic 30 RGB oocccnnnnnnnncncnnnononononnnnnonononnnnnnonononononannccnnnnnnnnnnnos 11036007 Warranty Information VY AU EUROS NEP T ETT 2 year limited warranty WERTE CONFORMS TO UL STD 1573 CERT
21. f two parts the product housing and the concrete installation sleeve The product housing is IP67 rated but the installation sleeve is not Please pay close attention to the installation instructions for the concrete installation sleeve regarding leveling and drainage You will have to run the AC power and signal cables into the concrete installation sleeve and the product s housing Do not use the product s junction box to extend the power or signal cables to other units because it may compromise the IP rating of the junction box Instead use individual cables from the product to the corresponding distribution boxes Installation Sleeve Orientation Orient the installation sleeve to allow the signal cable to enter the sleeve using one of the four cable inlets and the power cable to use the opposite inlet as seen in the figure This will reduce the stress to the signal and power cables when setting down the product while keeping them separated under the product s housing Signal Cable To power distribution box To signal distribution box Installation Sleeve Setup When setting up the installation sleeve make sure that any water that may have entered it can drain out of the sleeve on its own Locate the installation sleeve above the normal drainage level so the product is never under more than m of water IP67 during heavy rain In addition make sure that the installation sleeve and the stainless steel collar are h
22. fetime is rated to be 50 000 to 70 000 hours by the LED manufacturer LED Binning LED manufacturers sort LEDs into bins based on variances in color output intensity and the frequency at which the semiconductor operates ILUMINARC strives to hold its LED manufacturers to the highest standards of binning to optimize consistency in output from product to product However the availability of a single bin cannot be guaranteed With that in mind ILUMINARC has developed a rigorous control system to seek the best achievable consistency in color and output Color Rendering Index CRI CRI is an industry standard method to compare properties of different types of light sources There are known limitations and inconsistencies related to CRI Results may vary depending on the environmental factors involved For this reason the US Department of Energy DOE states that CRI should be considered as one point of reference among others in evaluating white LED products and systems The following is an excerpt of recommendations from the DOE 1 Identify the visual tasks to be performed under the light source If color fidelity under different light sources is critically important for example in a space where color or fabric comparisons are made under both daylight and electric lighting CRI values may be a useful metric for rating LED products 2 CRI may be compared only for light sources of equal CCT This applies to all light sources not o
23. he carton shows signs of mishandling see the Claims section in the Technical Information chapter Text Conventions Convention Meaning 1 512 A range of values in the text 50 60 A set of mutually exclusive values in the text ILUMICON UM The name of another publication or manual lt SET gt A button on the product s control panel SETTINGS A product function or a menu option MENU gt SETTINGS A sequence of menu options 1 10 A range of menu values from which to choose in a menu Yes No A set of two mutually exclusive menu options in a menu ON A unique value to enter or select in a menu llumipod Inground IP Series User Manual Rev 4 1 ntroduction There are no user serviceable parts inside this product Any reference to servicing it you may find from now on in this User Manual will only apply to properly ILUMINARC authorized technicians Do not open the housing or attempt any repairs unless you are certified to do so Please refer to all applicable local codes and regulations for the proper installation of this product Keep this manual for future consultation If you sell this product to Safety Notes Please read all the following safety notes carefully because they include important information on how to install use and maintain this product safely Personal Safety Avoid direct eye exposure to the light source while the product is on Always disconnect the Ilumipod Inground IP product from its p
24. iciency 48 7 Field 10 Beam 50 Total 25 6 352 8 56 8 Ilumipod Inground 36 IP Optic 30 RGB 100 ALL ILUMINARC Ilumipod Inground 36 IP Optic 30 RGB 12 Red 12 Green 12 Blue 1 lamp s rated Lumens lamp 1380 2 520 5 at Horizontal 0 Vertical 3 43 3 Point 2009 ALL Iluminarc R amp D Optics Laboratory Type B Direct Full Cutoff Polar Candela Distribution Bea 180 170 160 150 140 2 167 130 1 733 B57 433 100 CD D 307 86 1 300 1733 a m 2 167 2 600 B 07H M 90 H WA DP Li 180 H Li 270 H B 45 H 10 207 3p p Vertical Spread 55 2 28 8 Horizontal Spread 55 4 Lumens 672 7 784 4 Illuminance at a Distance Distance Center Beam Vertical Beam Width Horizontal Beam Width ft fc ft ft Photometrics 3 277 84 1 5 1 5 copyright 2003 6 69 46 3 1 3 0 2008 by 9 30 87 43 jSolutions Inc Reported data calculated from manufacturer s data file based on IES recommended methods 12 17 36 6 0 15 11 11 7 6 18 9 1 Vertical Spread 28 4 Horizontal Spread 29 3 llumipod Inground IP Series User Manual Rev 4 23 Technical Information llumipod Inground Tri 12 IP 16 Filename Manufacturer Luminaire Lamp Lamp Output Max Candela Input Wattage Luminous Opening Test Test Lab Photometry CIE Class Cutoff Class Flood Summary Efficiency Field 10 Ilumipod Inground Tri 12 IP Optic 16 RGB 100 ALL IL
25. junction box Data pubcomntreut non ee Pin 1 shield pin 2 pin 3 A A ae REITEN USITT DMX512 A DMX Channels Z Nee betwee 1 3 4 6 or 7 Ordering Information Nunupod Insround Tria 2 IP Opie ES ee ee a aha 11012001 Warranty Information WY ACUI em o PDT 2 year limited warranty UL 1573 8 CSAC22 2 No 166 C US E113093 llumipod Inground IP Series User Manual Rev 4 29 LUMINARC ILUMINARC
26. mber RMA ILUMINARC will refuse any product returned without the RMA Once you receive the RMA please include the following information on a piece of paper inside the box Your name Your address Your phone number The RMA A brief description of the problem Be sure to pack the product properly Any shipping damage resulting from inadequate packaging will be the customer s responsibility As a suggestion proper FedEx packing or double boxing is the shipping method ILUMINARC recommends Claims The carrier is responsible for any damage incurred during shipping Therefore if the received merchandise appears to have damages caused during shipping the customer must submit the damage report and any related claims with the carrier not ILUMINARC The customer must submit the report upon reception of the damaged merchandise Failure to do so in a timely manner may invalidate the customer s claim with the carrier For other issues such as missing components or parts damage not related to shipping or concealed damage the customer must make claims to ILUMINARC within seven 7 days of receiving the merchandise WORLD HEADQUARTERS ILUMINARC General Information Technical Support Address 5200 NW 108th Avenue Voice 800 762 1074 Sunrise FL 33351 Email support iluminarc com Voice 954 923 3680 Fax 800 544 4898 World Wide Web www iluminarc com UNITED KINGDOM AND IRELAND Chauvet Europe Ltd General Informatio
27. n Technical Support Address Unit 1C Email uktech iluminarc com Brookhill Road Industrial Estate Pinxton Nottingham UK World Wide Web www chauvetlighting co uk NG16 6NT Voice 44 0 1773 511115 Fax 44 0 1773 511110 MEXICO Chauvet Mexico General Information Technical Support Address Av Santa Ana 30 Email servicio iluminarc com mx Parque Industrial Lerma Lerma Mexico C P 52000 World Wide Web www chauvet com mx Voice 52 728 285 5000 CHAUVET EUROPE Chauvet Europe BVBA General Information Technical Support Address Stokstraat 18 Email Eutech chauvetlighting eu 9770 Kruishoutem Belgium World Wide Web www chauvetlighting eu Voice 329 388 93 97 Outside the U S United Kingdom Ireland Mexico or Benelux contact the dealer of record Follow their instructions to request support or to return a product Visit our website for contact details llumipod Inground IP Series User Manual Rev 4 LUMINARC Technical Information Technical Specifications llumipod Inground 36 IP VW Weight amp Dimensions MYNME sates ted SP ete sth S 12 6 in 320 mm A OZONE NOA 5 7 in 146 mm PPP A 17 6 lbs 8 kg Power IO A e E 100 240 VAC 50 60 Hz Power consumption 120 V ren ee cited 38 W 0 6 A Power consumption 230 nn 40 W 0 3 A ruh e aaia ai 0 1 A 120 V 0 3 A 230 V Power conne IT asian Terminal strip in sealed junction box Light Source HE EC OCENE 1 W 350 mA 50 000 hrs LEDs A 36 LEDs
28. nd RGB products can also work with the ILUMICON controller instead of a standard DMX controller Please refer to the ILUMICON User Manual to learn how to use this controller with the Ilumipod Inground IP products The figure below illustrates how to connect the ILUMICON controller to the Ilumipod Inground IP Tr and RGB products other fixtures ILUMICON Controller Installation Installation To assign individual DMX addresses to each product you must connect the llumicode controller to each product individually ILUMINARC suggests that you connect no more than 20 products in this mode and keep the total distance to less than 60 m 197 ft Otherwise you might need to use an optically isolated signal amplifier LUMINARC llumicode The diagram below shows how to connect the Ilumicode to this product Note that this connection will control multiple products at the same time all having the same DMX address To other fixtures 1 Gnd 1 Gnd Black clip 2 Data 2 Data Green clip 3 Data 3 Data Red clip DMX Output Signal Connector llumipod Inground IP Series User Manual Rev 4 A m NA LUMINARC 4 Operation llumicode Operation The products in the Ilumipod Inground IP Series lack a control panel Therefore they need an external controller the Ilumicode device to change their configuration llumicode Panel Description Button lt MENU gt lt ENTER gt lt U
29. nly to LEDs Also differences in CRI values of less than five points are not significant e g light sources with 80 and 84 CRI are essentially the same 3 If color appearance is more important than color fidelity do not exclude white light LEDs solely on the basis of relatively low CRI values Some LED products with CRIs as low as 25 still produce visually pleasing white light 4 Evaluate LED systems in person and if possible on site when color fidelity or color appearance are important issues Source DOE publication PNNL SA 56891 January 2008 llumipod Inground IP Series User Manual Rev 4 25 Technical Information IL UJI DO NOT write the RMA directly on the box Instead write it on a properly affixed label ILUMINARC reserves the LA right to use its own discretion to repair or replace returned product s Always keep the original box and all packaging material as you will need those to ship the unit back to ILUMINARC Contact Us 26 Returns Procedure The user must send the merchandise prepaid in the original box and with its original packing and accessories ILUMINARC will not issue call tags Call ILUMINARC and request a Return Merchandise Authorization Number RMA before shipping the product Be prepared to provide the model number serial number and a brief description of the cause for the return The user must clearly label the package with a Return Merchandise Authorization Nu
30. o not operate this product at a higher temperature In case of a serious operating problem stop using this product immediately llumipod Inground IP Series User Manual Rev 4 m j in HE AR 4 i zg LIMIT ARG Product Description Rams 2 Product Description The Ilumipod Inground IP Series encompasses three products Ilumipod Inground 36 IP RGB Ilumipod Inground 36 IP VW and Ilumipod Inground Tri 12 IP X i b a gt A Common Features Other than their LED configuration and programming features these three products share the same dimensions as well as the installation wiring and troubleshooting procedures The lenses in these three products are non changeable Therefore make sure to use the right product order code for the desired lens angle llumipod Inground IP Series User Manual Rev 4 Remotely addressable DMX 512 LED inground wash light IP67 ingress protection IP67 stainless steel gland nuts for cable entry Adjustable module angle Cast aluminum and stainless steel housing Impact resistant tempered glass lens cover drive over rated Polished stainless steel mounting ring Ilumicode compatible llumipod Inground 36 IP VW Features Operating modes 1 channel Dimmer 2 channel Warm white cool white 3 channel Warm white cool white dimmer High power 1 W 750 mA Warm White and Cool White LEDs Installed non changeable optical system 15
31. ol dimmer 1 channel dimmer OFF Dimmer work in linear mode N A Dimmer works in non linear mode from fast to slow 0 255 Configures the static color and effect WARM 11 Operation ILLU RGB Functions Menu Map Ilumipod Inground 36 IP RGB and llumipod Inground Tri 12 IP Main Level Programming Levels Description DMX 001 512 N A Sets the DMX starting address When you scroll ARC 1 3 channel RGB control through the menu options ARC 1 D 4 channel RGB control dimmer you will see ARC FULL 7 channel RGB control dimmer color macro strobe many of in ied do not PERSON N A dimmer speed correspond with this menu REMOTE map Skip them as they REMOTE Allows using the ILUMICON unit do not work with the RGB SPECIALI 6 channel RGB control per module only output products SOLID 1 channel dimmer WHITE 1 11 RED Determines the white balance for the color macros CALIB GREN 0 255 RGBTOW BLUE Determines the white balance when RGBTOW is active Dimmer work in linear mode DIM 1 DIMMER DIM 2 N A Dimmer works in non linear mode from fast to slow DIM 3 DIM 4 RED STATIC OREN 0 255 Configures the static color and effect BLUE If you scroll after STRB lt STRB you will i SS see the AMBE OFF Maximum output unbalanced white COOL and COLOR RGBTOW White output is as per CALIB gt RGBTOW settings WARM colors Just skip SETTINGS them as they do not work Output matches that of product s previous versions with the RGB products RE
32. orizontal and even with the ground surface This helps to distribute the load uniformly over the product s surface and avoids creating dangerous bumps lt Collar Concrete Drainpipe Hardpan Installation Installation Make sure to disconnect the power to the product before opening it Be careful when opening and closing the product s housing as it may compromise the products IP67 rating LUMINARC Beam Angle Adjustment The Ilumipod Inground IP products have two LED modules each You can adjust the angle of each of these modules to spread or narrow the product s beam To do so follow these steps L 10 11 12 13 Loosen the Allen bolts on the stainless steel collar by turning them CCW not more than a turn or two enough to release the aluminum latch from its locked position Lift the product from the installation sleeve making sure not to stretch the power and signal cables Loosen four of the six nuts that hold the collar to the housing leaving untouched any two adjacent nuts Wait a few seconds for the seal to expand This lowers the possibility of damaging the seal Complete the removal of the two remaining nuts Remove the stainless steel collar Carefully lift and remove the protective glass and the seal attached to it making sure not to reverse the glass Using only your hands push on the sides of each module to adjust its angle as shown in the figure
33. ower source before servicing CAUTION When transferring product from extreme temperature environments e g cold truck to warm humid ballroom condensation may form on the internal electronics of the product To avoid causing a failure allow product to fully acclimate to the surrounding environment before connecting it to power Always connect the Ilumipod Inground IP product to a grounded circuit to avoid the risk of electrocution Mounting and Installation The Ilumipod Inground IP products are for outdoor use and they can work while submerged in up to I m of water IP67 However do not submerge it deeper than 1m for more than 30 thirty minutes Observe the installation instructions regarding drainage to ensure that the water level is never higher than 1 m for more than 30 thirty minutes to comply with the IP67 rating another user make sure that they also receive this Power and Wiring manual Always make sure that you are connecting this product to the proper voltage as per the specifications in this manual or on the product s sticker In the unlikely Never connect this product to a dimmer pack D o PSR Make sure that the power cable is not cracked crimped or damaged Inground IP product may Make sure that the sealed cover is properly adjusted to avoid water entering the unit require service please contact ILUMINARC Operation Technical Support The maximum ambient temperature Ta is 113 F 45 C D
34. pod Inground IP Series User Manual Rev 4 19 Technical Information Photometrics llumipod Inground 36 IP 15 VW Filename Manufacturer Luminaire Lamp Lamp Output Max Candela Input Wattage Luminous Opening Test Test Lab Photometry CIE Class Cutoff Class Flood Summary Field 10 Ilumipod Inground 36 IP Optic 15 RGB 100 ALL ILUMINARC Ilumipod Inground 36 IP Optic 15 RGB 12 Red 12 Green 12 Blue 1 lamp s rated Lumens lamp 1380 8 753 5 at Horizontal 180 Vertical 3 43 1 Point 2009 ALL Iluminarc R amp D Optics Laboratory Type B Direct Full Cutoff Polar Candela Distribution me 180 170 160 1509 140 7 313 1302 5 867 1208 4 400 2 933 110 1 467 1002 CD D 90 1 467 son 2 933 p 4 400 5D 5 867 7 333 52 8 800 Photometrics Pro 1 3 2 copyright 2003 2008 by jSolutions Inc Reported data calculated from manufacturer s data file based on IES recommended methods 20 Efficiency Lumens Horizontal Spread Vertical Spread 40 3 556 6 28 17 7 244 3 13 4 Beam 50 Total 768 1 55 7 Illuminance at a Distance Distance Center Beam Vertical Beam Width Horizontal Beam Width ft fc ft ft 3 0 7 6 1 4 9 2 1 12 2 8 15 3 4 18 4 1 Vertical Spread 13 42 Horizontal Spread 13 1 llumipod Inground IP Series User Manual Rev 4 re ILUMINAR r 1 UT Technical Information llumipod Inground 36 IP 30
35. ssae data dos 25 Returns Procedure otc ae lass 26 d i mec H na age 26 Technical Speeificallonsen u ans is 27 NEIIBOA SIHGFOUNG SEHIF VW 2222 eur ra 27 Humipod Inground 36 IF HGB iius o m EE bos Maa ts hae eed 28 NOUMIDOGAKGFOUKA T I 2 rc EP 29 i llumipod Inground IP Series User Manual Rev 4 a E El T Il LJIVII V ome M t p d 2 Y i y gt MI U j Mi 1 Introduct This icon indicates useful although non critical information This icon indicates important installation or configuration information Failure to comply with this information may prevent the product from functioning correctly This icon indicates critical installation configuration or operation information Failure to comply with this information may render the product partially or completely inoperative damage third party equipment or cause harm to the user _ The term DMX A used throughout this document refers to the USITT DMX512 A transmission protocol Ee Introduction on What is in the Box One Ilumipod Inground IP product 36 IP RGB 36 IP VW or Tri 12 IP Warranty Card Quick Reference Guide Unpacking Instructions Immediately upon receiving a product from ILUMINARCO carefully unpack the carton Check the contents of the box to ensure that all parts are present and that they are in good condition If any part appears damaged from shipping or if t
36. st Test Lab Photometry CIE Class Cutoff Class Ilumipod Inground 36 IP Optic 15 RGB 100 ALL ILUMINARC Ilumipod Inground 36 IP Optic 15 RGB 12 Red 12 Green 12 Blue 1 lamp s rated Lumens lamp 1380 8 753 5 at Horizontal 180 Vertical 3 43 1 Point 2009 ALL Iluminarc R amp D Optics Laboratory Type B Direct Full Cutoff Polar Candela Distribution 1507 17 07 1609 150 140 8 800 7 333 5 867 4 400 2 933 110 1 467 CD 0 1 467 2 933 4 400 5 867 7 333 8 800 2938838 _ VAI 107 2p 30 Ea B 0H C 180 H M 90 H L 270 H B 45 H Flood Summary Efficiency Lumens Horizontal Spread Vertical Spread Field 10 28 Beam 50 13 4 55 7 Total 768 1 Illuminance at a Distance Distance Center Beam Vertical Beam Width Horizontal Beam Width ft fc ft ft 3 907 01 0 7 6 226 75 1 4 Photometrics Pro 9 100 78 21 LA 2003 2008 by 12 56 69 2 8 2 8 jSolutions Inc 15 36 28 34 Reported data calculated 18 25 19 4 1 from manufacturer s data SE file based on IES Vertical Spread 13 4 Horizontal Spread 13 1 recommended methods 22 llumipod Inground IP Series User Manual Rev 4 re ILUMINAR r 1 UT Technical Information llumipod Inground 36 IP 30 RGB Filename Manufacturer Luminaire Lamp Lamp Output Max Candela Input Wattage Luminous Opening Test Test Lab Photometry CIE Class Cutoff Class Flood Summary Eff
37. ted in the figure on the right Connection Wire US Wire Europe Live Brown Neutral Blue Ground Green Yellow Green Yellow AC Power Input Wiring llumipod Inground IP Series User Manual Rev 4 Installation Installation The signal cable must match or exceed the electrical characteristics of the Belden 9841 cable for EIA RS 485 applications If you choose to D bury the power or signal distribution boxes make sure that they are IP67 rated ILUIMINABHC Signal Wiring To provide signal for any of the Ilumipod Inground IP products you must run a single IP67 rated DMX signal cable shielded 2 conductor AWG24 2 6 5 mm external diameter 120 ohm typical impedance from the signal distribution box into the installation sleeve and the product s junction box External Wiring You must run AC power and signal wires from the respective AC and signal distribution boxes into each of the Ilumipod Inground IP products Power Distribution Connect the bare ended power cable from the product to a power distribution box as indicated below igl al L Black Z From Hn AS D eme 1 Ss panel i Seem y 1 1 boxes Du MEER HE peer d LT 7 1____r gt Distribution Conduit or Distribution Box pec Box Signal Distribution E Connect the bare ended signal cable from the product to a signal distribution box as indicated Nall al 1 Common Black below 2 Data
38. tion of glass cleaner or isopropyl alcohol and a soft lint free cotton cloth or a lens cleaning tissue to remove grease or grime 11 Apply the solution directly to the cloth or tissue and drag any dirt and grime to the outside of the lens 12 Gently polish the external glass surface until it is free of haze and lint Product Repairs ILUMINARC strongly advises you against attempting any repairs to this product unless you are an authorized ILUMINARC technician ILUMINARC presents the information contained in the Troubleshooting Table as a guide only In most cases opening the product s housing will invalidate its warranty unless there is a written indication to the contrary llumipod Inground IP Series User Manual Rev 4 17 Technical Information IL LJIVII Troubleshooting Guide Symptom Cause s Action s Dimmer fader set to 0 Increase the value of the dimmer channel All color faders set to 0 Increase the value of the color channels All colors in STATIC are set to 0 Increase the values of the colors Product does not light up Unit is being configured with Ilumicode Complete the configuration process Verify external power circuit and wiring Faulty internal power supply Return for service to Iluminarc Faulty main control board Return for service to Iluminarc Faulty LED E Return for service to Iluminarc One LEDs does not work Faulty LED module Faulty LED driver Return for service to Iluminar
Download Pdf Manuals
Related Search