Users Manual - Audio General Inc.
Contents
1. Computer gt on ESE You can use a USB extension cable for Z computers with SE The USB port SS will be marked difficult to reach N with a logo USB ports or to reposition the receiver Page 5 Installing the Batteries Step 1 Take out the USB receiver or plug Remove receiver or plug prior to installing batteries Cover can not be removed when inserted Step 2 Open Remote Turn theremote upside down and push on the eject slider to release the outer cover Step 3 Remove Cover Separate the outer cover from the remote by gently pulling on the top and bottom in opposite directions Once separated turn the remote over Page 6 Step 4 Add Batteries Open the battery compartment by pressing down on the latch Insert the batteries per the diagram on the remote Step 5 Set the Clock Set the clock by pressing the clock set button The hour will start blinking Use the following keys to set the time A Increase value Decrease value Move to next digit Done For PC users there is a Clock Setting Utility available at http www interlinkelectronics com support downloads html Page 7 Step 6 Reassemble Reassemble your remote by closing the battery door and sliding the outer cover over the remote until it clicks into place Presenting A Next Slide Advance to the next slide W Previous Slide Return to the previous slide Start Presentation Pres2. Users Manual RemotePoint Onyx INTERLINK ELECTRONICS Page 1 THANK You Thank you for purchasing a RemotePoint Onyx Presentation Remote We know you had other choices and we appreciate that you chose Interlink Electronics for your wireless needs So that we may better serve you in the future please register online at www interlinkelec com register Sincerely EMI E Michael Thoben President Chairman and CEO Interlink Electronics Inc WARRANTY 30 Day Money Back Guarantee 2 Year Limited Warranty Page 2 FCC Certification This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a CLASS B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation This equipment generates uses can radiate radio frequency energy and if not installed and used in accordance with the instruction guide may cause harmful interference to radio communications However there is no guarantee that this radio interference will not occur in a particular installation If this equipment does cause harm
3. When removing the receiver from the remote the indicator LED flashes red repeatly Solution The batteries in the remote have reached a low voltage level and need to be replaced The unit may continue to operate but for a limited time Page 10 For Product Support Please Contact 546 Flynn Road Camarillo CA 93012 USA TEL 888 696 3500 FAX 805 484 5997 INTERLINKELECTRONICS COM P N 94 01441 Rev P2 Page 11
4. ful interference to radio or television reception which can be determined by turning the equipment on and off the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiving antenna Increase the separation between the equipment and the receiver Consult the dealer or an experienced Radio TV technician for help Page 3 Notice Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Extension cables are not recommended if used they must be shielded in order to comply with the emission limits IC Certification The term IC before the certification registration number only signifies that the Industry Canada technical specifications were met Declaration of conformity Manufacturer Interlink Electronics Inc 546 Flynn Road Camarillo CA 93012 We declare under our sole responsibility that the VP4700 conforms to the following directives and norms CAUTION Directive 89 336 EEC Amended by 93 68 Wa STARE INTO BEAM EEC VMAX OUTPUT lt imi EMI EN 55022 1992 Class B c GLASS II LASER PRODUCT l EMC EN 50082 1 1992 Directive 73 23 EEC Amended bv 93 68 EEC Safetv EN 60950 2000 Page 4 Connecting the USB Receiver e Remove the USB receiver from the remote e Insert the USB receiver into any available USB port on the computer
5. s this to start your presentation Starts from your current posi tion IM Blank Screen Use the blank screen button to hide your presentation while you make a key point Press again to reveal the presen tation Page 8 Using the Laser Pointer Press the button on the front of the remote to activate the laser pointer The CAUTION aser pointer can be used to i highlight important points on Mtsorte slides and graphs c GLASS II LASER PRODUCT J Using with a Macintosh The remote control has three different compatibility modes The light on the USB receiver will blink one to three times every second or so to tell you which mode your receiver is currently set to Mode 1 Windows computers running Microsoft PowerPoint Mode 2 Macintosh P running Keynote Mode 3 Macintosh computers running Microsoft PowerPoint Page 9 To switch modes you will need a pointy object such as a paper clip While the receiver is plugged into a USB port press down on the recessed button on the receiver Each time you press the button it will move to the next mode Once set the mode is remembered for next time Troubleshooting Problem When you plug the receiver into the remote the light on the next slide button blinks repeatedly for several minutes Solution The remote and the receiver are unable to pair Unplug the receiver and try again If this continues please contact support Problem
Download Pdf Manuals
Related Search