WEEP-MASTER - Dilling
Contents
1. then it will show the lowest temperature for 1 second and then show the highest temperature for 1 second then back to current temperature The high and low temperature can be reset by pushing the button on the control board or by cycling the power to the Weep Master When reset the display will only show the current temperature until there is a temperature change for it to record and report This feature cannot be turned off Temperature Probe The Weep Master only requires one probe to operate Additional probe connections are supplied on the control board Adding another probe can be useful but the system will only read the lowest temperature of all probes used An example of using 2 probes would be having 1 probe on opposite sides of a building That way if one probe was in the sun or near something warmed by the sun the other would detect the lower temperature NOTICE ONLY use temperature probes supplied by Dilling Harris Dip Switches Number and function for each Factory Dip Switch Setting All Switches OFF Dip Switch number 1 Temperature at which the system starts to cycle Off position starts at 35 On position starts at 40 2 amp 3 They are combined to set up the cycle length in seconds 2 amp 3 Off 60 seconds cycle 2 Off 3 On 30 seconds cycle 2 On 3 Off 90 seconds cycle 2 On 3 On 120 seconds cycle 4 amp 5 They are combined to set up Zone area 4 amp 5 Off Zone 1 4 Off 5 Zone 2 42. ECTIONS DIP SWITCHES 24v HOT 24v COMMON 10 FUSE 0000000000 l TEMPERATURE PROBE OPTIONAL TEMPERATURE PROBE WEEP VALVE N O AUXILIARY OUTPUT OPTIONAL TEMPERATURE PROBE
3. EMPETURE RANGE FLOW ON SEC FLOW OFF SEC 100 14 AND UNDER CONTINUOUS 0 ZONE 2 DIP SWITCH 4 OFF 5 ON FLOW TEMPETURE RANGE FLOW ON SEC FLOW ZONE 3 DIP SWITCH 4 ON 5 OFF FLOW TEMPETURE RANGE FLOW ON SEC FLOW OFF SEC 15 CONTINUOUS 0 __100 14 ANDUNDER CONTINUOUS 0 ZONE 4 DIP SWITCH 4 ON 5 ON FLOW RANGE FLOW ON SEC FLOW OFF SEC 100 20 16 CONTINUOUS 0 15 CONTINUOUS 100 14 AND UNDER CONTINUOUS O WEEP CYCLE CHART AT 60 SECOND CYCLE 35 START TEMP DIP SWITCH 1 2 3 OFF FACTORY SETTING ALL DIP SWITCHES OFF ZONE 1 DIP SWITCH 4 OFF 5 OFF FLOW TEMPETURE RANGE FLOW ON SEC FLOW OFF SEC 100 14 AND UNDER CONTINUOUS 0 ZONE 2 DIP SWITCH 4 OFF 5 ON FLOW TEMPETURE RANGE FLOW a FLOW OFF SEC CONTINUOUS ZONE 3 DIP SWITCH 4 ON 5 OFF FLOW TEMPETURE RANGE FLOW ON SEC FLOW OFF SEC 15 CONTINUOUS 0 100 14 ANDUNDER CONTINUOUS 0 ZONE 4 DIP SWITCH 4 ON 5 ON FLOW RANGE FLOW ON SEC FLOW OFF SEC 100 20 16 CONTINUOUS 0 15 CONTINUOUS 100 14 AND UNDER CONTINUOUS O WEEP CYCLE CHART AT 90 SECOND CYCLE 35 START TEMP DIP SWITCH 1 OFF 2 ON 3 OFF ZONE 1 DIP SWITCH 4 OFF 5 OFF FLOW TEMPETURE RANGE FLOW ON SEC FLOW OFF SEC 100 14 AND UNDER CONTINUOUS 0 ZONE 2 DIP SWITCH 4 OFF 5 ON FLOW
4. INUOUS 0 20 CONTINUOUS 100 19 AND UNDER CONTINUOUS O WEEP CYCLE CHART AT 120 SECOND CYCLE 40 START TEMP DIP SWITCH 1 ON 2 ON 3 ON ZONE 1 DIP SWITCH 4 OFF 5 OFF FLOW TEMPETURE RANGE FLOW ON SEC FLOW OFF SEC 100 19 AND UNDER CONTINUOUS 0 ZONE 2 DIP SWITCH 4 OFF 5 ON FLOW TEMPETURE RANGE FLOW FLOW OFF SEC CONTINUOUS ZONE 3 DIP SWITCH 4 ON 5 OFF FLOW TEMPETURE RANGE FLOW ON SEC FLOW OFF SEC 20 CONTINUOUS 0 100 19 ANDUNDER CONTINUOUS O ZONE 4 DIP SWITCH 4 ON 5 ON FLOW RANGE FLOW ON SEC FLOW OFF 5 100 25 21 CONTINUOUS 0 20 CONTINUOUS 100 19 AND UNDER CONTINUOUS O Temperature Probe Adjustment The Temperature Probe should not need adjustment If you find that the temperature is off by a degree or two you can fine tune it Instructions 1 Disconnect power to the Weep Master 2 Find the row of DIP switches on the Weep Master control board Change the 11 dip switch to the position Restore power the display will show 0 0 There are 9 possible correction off sets available Using the yellow push button on the back of the Weep Master s control board you can toggle through the off sets Display 0 5 Repeats back to 0 0 3 After an off set is selected cut power change the 11 dip switch back to the off position Restore power 14 WEEP MASTER CONN
5. NUOUS 0 __100 19 ANDUNDER CONTINUOUS O ZONE 4 DIP SWITCH 4 ON 5 ON FLOW RANGE FLOW ON SEC FLOW OFF 5 100 25 21 CONTINUOUS 0 20 CONTINUOUS 100 19 AND UNDER CONTINUOUS O WEEP CYCLE CHART AT 60 SECOND CYCLE 40 START TEMP DIP SWITCH 1 ON 2 OFF 3 OFF ZONE 1 DIP SWITCH 4 OFF 5 OFF FLOW TEMPETURE RANGE FLOW ON SEC FLOW OFF SEC 100 19 AND UNDER CONTINUOUS 0 ZONE 2 DIP SWITCH 4 OFF 5 ON FLOW TEMPETURE RANGE FLOW a FLOW OFF SEC CONTINUOUS ZONE 3 DIP SWITCH 4 ON 5 OFF FLOW TEMPETURE RANGE FLOW ON SEC FLOW OFF SEC 20 CONTINUOUS 0 100 19 ANDUNDER CONTINUOUS O ZONE 4 DIP SWITCH 4 ON 5 ON FLOW RANGE FLOW ON SEC FLOW OFF 5 100 25 21 CONTINUOUS 0 20 CONTINUOUS 100 19 AND UNDER CONTINUOUS O WEEP CYCLE CHART AT 90 SECOND CYCLE 40 START TEMP SWITCH 1 ON 2 ON OFF ZONE 1 DIP SWITCH 4 OFF 5 OFF FLOW TEMPETURE RANGE FLOW ON SEC FLOW OFF SEC 100 19 AND UNDER CONTINUOUS 0 ZONE 2 DIP SWITCH 4 OFF 5 ON FLOW TEMPETURE RANGE FLOW FLOW 2 ZONE 3 DIP SWITCH 4 ON 5 OFF FLOW TEMPETURE RANGE FLOW ON SEC FLOW OFF SEC 20 CONTINUOUS 0 __100 19 ANDUNDER CONTINUOUS O ZONE 4 DIP SWITCH 4 ON 5 ON FLOW RANGE FLOW ON SEC FLOW OFF 5 100 25 21 CONT
6. On 5 Zone 4On 5On Zone 4 See WEEP CYCLE CHARTS for more information 6 amp 7 They are combined to turn on the Auxiliary Output Low temperature activation Ex Close automatic bay doors 6 amp 7 Off On at 35 and below 6 Off 7On at 40 and below 6 On 7 Off at 45 and below 6 On 7 On On at 50 and below 8 9 amp 10 They are combined to turn on the Auxiliary Output High Temperature activation Ex Open automatic bay doors 8 9 amp 10 Off No activation 8 Off 9 Off 10 On 55 and above 8 Off 9 10 Off 60 and above 8 9 10 On 65 and above 8 On 9 Off 10 Off 70 and above 8 On 9 Off 10 On 75 and above 8 On 9 On 10 Off 80 and above 8 9 amp 10 On 90 and above 11 Mode Switch 11 Off normal run mode 11 On Probe Calibration mode 12 Temperature in F or 12 Off 12 C WEEP MASTER ZONE CHART FIND THE ZONE FOR YOUR LOCATION AND CHOOSE SETTINGS FROM THE LIST BELOW WITH 35 START TEMP SETTING WITH 40 START TEMP SETTING ZONE 1 ALL SW OFF STANDARD SW 1 ON ZONE 2 SW 5 ON SW 1 5 ON ZONE 3B SW 4 ON SW 1 4 ON ZONE 4 SW 4 5 ON SW 1 4 5 ON ZONE 3 WITH A START TEMP OF 40 WILL ALSO BE GOOD FOR ZONE 4 WEEP CYCLE CHART AT 30 SECOND CYCLE 35 START TEMP DIP SWITCH 1 OFF 2 OFF 3 ON ZONE 1 DIP SWITCH 4 OFF 5 OFF FLOW T
7. TEMPETURE RANGE FLOW FLOW 2 ZONE 3 DIP SWITCH 4 ON 5 OFF FLOW TEMPETURE RANGE FLOW ON SEC FLOW OFF SEC 15 CONTINUOUS 0 __100 14 ANDUNDER CONTINUOUS 0 ZONE 4 DIP SWITCH 4 ON 5 ON FLOW RANGE FLOW ON SEC FLOW OFF SEC 100 20 16 CONTINUOUS 0 15 CONTINUOUS 100 14 AND UNDER CONTINUOUS O WEEP CYCLE CHART AT 120 SECOND CYCLE 35 START TEMP DIP SWITCH 1 OFF 2 ON 3 ON ZONE 1 DIP SWITCH 4 OFF 5 OFF FLOW TEMPETURE RANGE FLOW ON SEC FLOW OFF SEC 100 14 AND UNDER CONTINUOUS 0 ZONE 2 DIP SWITCH 4 OFF 5 ON FLOW TEMPETURE RANGE FLOW FLOW OFF SEC CONTINUOUS ZONE 3 DIP SWITCH 4 ON 5 OFF FLOW TEMPETURE RANGE FLOW ON SEC FLOW OFF SEC 15 CONTINUOUS 0 100 14 ANDUNDER CONTINUOUS 0 ZONE 4 DIP SWITCH 4 ON 5 ON FLOW RANGE FLOW ON SEC FLOW OFF SEC 100 20 16 CONTINUOUS 0 15 CONTINUOUS 100 14 AND UNDER CONTINUOUS O WEEP CYCLE CHART AT 30 SECOND CYCLE 40 START TEMP DIP SWITCH 1 ON 2 OFF 3 ON ZONE 1 DIP SWITCH 4 OFF 5 OFF FLOW TEMPETURE RANGE FLOW ON SEC FLOW OFF SEC 100 19 AND UNDER CONTINUOUS 0 ZONE 2 DIP SWITCH 4 OFF 5 ON FLOW TEMPETURE RANGE FLOW ON SEC FLOW ZONE 3 DIP SWITCH 4 ON 5 OFF FLOW TEMPETURE RANGE FLOW ON SEC FLOW OFF SEC 20 CONTI
8. WEEP MASTER USER S MANUAL Grant Dilling Harris Inc 1701 Capital Ave Plano TX 75074 972 424 3531 800 767 3531 Contents Weep Master Display information 3 Temperature Probe information 3 Dip Switch information 4 Weep Master Zone Chart 5 Weep Cycle Chart 30 sec 35 Start Temp 6 Weep Cycle Chart 60 sec 35 Start Temp 7 Weep Cycle Chart 90 sec 35 Start Temp 8 Weep Cycle Chart 120 sec 35 Start Temp 9 Weep Cycle Chart 30 sec 40 Start Temp 10 Weep Cycle Chart 60 sec 40 Start Temp 11 Weep Cycle Chart 90 sec 40 Start Temp 12 Weep Cycle Chart 120 sec 40 Start Temp 13 Temperature Probe Adjustment 14 Wiring Connections 15 Weep Master Default Settings The Weep Master is shipped with all the dip switches in the off position The default parameters are 1 the system will start to cycle the weep solenoid 35 2 the cycle length will be 60 seconds 3 itis set for Zone 1 4 auxiliary output low temperature activation is set for 35 5 auxiliary output high temperature activation is set for no activation 6 set for normal run mode 7 temperature display set for F Weep Master Display The Weep Master display has 3 automatic functions 1 Current outside temperature 2 Lowest outside temperature since last re set 3 Highest outside temperature since last re set The display has rotating information displayed it will show the current outside temperature for 10 seconds
Download Pdf Manuals
Related Search