3M™ Littmann® Electronic Stethoscope Model 3200
Contents
1. To select auto off power management Select the AUTO OFF option in the SETUP menu Use the and buttons to scroll through the list of options Press and release the M button to select The factory default is ENABLE SETUP eee BACKLITE FILTERS s i ENABLE MV DISABLE Two different settings work together to influence the length of time the Model 3200 is on full power The AUTO OFF setting ENABLE vs DISABLE and the POWER setting HIGH MEDIUM and LOW HIGH setting uses more battery power LOW setting uses less battery power To increase battery life ENABLE the AUTO OFF feature and select the LOW power setting When the AUTO OFF feature is enabled the stethoscope will enter standby mode after a period of time determined by the POWER setting if there is no contact detected on the diaphragm AND the buttons are not activated When the AUTO OFF feature is disabled the stethoscope will enter standby mode after a period of time determined by the POWER setting from the last button activation In addition when the AUTO OFF feature is disabled there will be an audible alert 10 seconds prior to entering standby mode After entering standby mode the Model 3200 will be powered on when contact is detected on the diaphragm or by button activation Otherwise the Model 3200 will completely power off after the period of time determined by the POWER setting see below With AUTO OFF feature ENABLED Remains on full power for 30 seconds bef2. Consult application software for details on initiating real time transfer the process may vary by computer platform utilized m 5 3 MAIN DISCONN H 123 When connected by a Bluetooth link external Bluetooth enabled devices may take control of the display and keypad of the Model 3200 stethoscope The external device may also transfer audio playback or other information through the Model 3200 headset When the external device transfers audio playback back to the stethoscope the sounds will be preceded by a beep A Bluetooth connection with the stethoscope will automatically be ended if no data transfers occur in a 90 second period Alternatively the connection can be manually ended using the DISCONN disconnect option of the Main menu If you are listening to the Model 3200 electronic stethoscope using its Bluetooth feature and you exceed the maximum communication range of approximately 10 meters you may hear a rapid series of beeps Should this occur shorten the physical distance between your Model 3200 and the Bluetooth equipped device MAIN CONNECT DOISCONH RECORD i 2 D Li 11 Using Onboard Recording Onboard recording provides a means to acquire and play an auscultation sound track for a maximum of 29 seconds This track can be uploaded to an external device using the Bluetooth link and the software accompanying the Model 3200 How to record a sound track 1 Enter the recording mode Depress and
3. The diaphragm can easily be cleaned by using an alcohol wipe If however it is necessary to remove the diaphragm carefully follow the instructions below e Diaphragm Removal With diaphragm side up using a thumbnail lift the underside portion of the diaphragm out of its designated groove and peel it off of the chestpiece The groove that holds the diaphragm in place can be cleaned by sliding the edge of an alcohol swab around the groove All parts of the chestpiece can be wiped down with alcohol IMPORTANT The stethoscope should not be immersed in any solution Excess liquid used in the cleaning process may result in moisture getting into the internal components e Diaphragm Reassembly Once the diaphragm is completely dry insert the diaphragm into the groove of the rim starting at one point and run your finger around the diaphragm until it is seated back in the groove 17 Cleaning Other Parts of the Stethoscope APPENDIX Eartips eartubes plastic tubing and chestpiece can be wiped clean with alcohol Eartips may be removed for a more s thorough cleaning Declaration Electromagnetic Emissions NOTIGE Do not immerse the stethoscope in any liquid or subject it to any sterilization process The 3M Littmann Electronic Stethoscope Model 3200 is intended for use in the electromagnetic environment Service amp Warranty Program specified below The customer or the user of the Model 3200 should assure that it is used in such an envi
4. Model 3200 as F licitations et merci d avoir choisi le St thoscope lectronique 3M Littmann Mod le 3200 recommended below according to the maximum output of the communications equipment Le Mod le 3200 vous offre la technologie la plus avanc e en auscultation et en lectronique sans fil dans un format power of transmitter La combinaison du Mod le 3200 de la technologie de R duction du Bruit Ambiant les mat riaux de r duction du bruit de P W frottement l amplification lectronique modes diaphragme alarme conventionnelle plus un mode de gamme tendue d212NP le transfert de donn es par Bluetooth et une toute nouvelle interface utilisateur vous am nent un niveau sup rieur de performance et de facilit d utilisation Que vous auscultiez des nourrissons des enfants ou des adultes dans des environnements sonores calmes ou bruyants ou que vous cherchiez entendre les bruits du coeur ou autres sons du corps difficilement perceptibles vous appr cierez toute la technologie mise au point dans cette derni re version du St thoscope lectronique de la marque Littmann Ne manquez aucune occasion de saisir tous les sons que vous d sirez entendre INFORMATIONS DE SECURITE Veuillez prendre connaissance et suivre toutes les consignes de s curit contenues dans ces instructions avant d utiliser cet appareil Conserver ces instructions afin de vous y r f rer ult rieurement For transmitters rated at a maximum output po
5. protocols used by the Model 3200 IMPORTANT The Model 3200 uses a Class 2 Bluetooth link with a maximum range of 10m The Bluetooth range will be reduced when objects walls furniture people etc are in between the Model 3200 and the external device To improve Bluetooth communication reduce the distance and or allow a line of sight between the Model 3200 and the external device 13 i 2 D LLi In order to transfer data between two Bluetooth devices they must first be paired electronically Pairing is a discovery and authentication process that allows your Bluetooth equipped Model 3200 to communicate with another Bluetooth equipped device and establishes the link between these two devices as a trusted pair The pairing process requires user operations to be performed on both the Model 3200 and the external device While the Model 3200 can remember trusted pairing with up to eight different Bluetooth devices it will only communicate with one paired device at a time In addition you cannot pair a Model 3200 with a second Model 3200 How to pair the Model 3200 with an external device 1 Initiate pairing process On the Model 3200 depress and release the M button The MAIN menu will be displayed Use the button to scroll down to the PAIR option Select this option by pressing and releasing the M button The LCD screen will signal that pairing is in progress with the following animated display During the pairing p
6. Littmann Brand Electronic Stethoscope MODEL 3200 Featuring 4 On Board Recording Ambient Noise Reduction Bluetooth Technology Bluetooth Made in Denmark for 3M Health Care St Paul MN 55144 U S A 1 800 228 3957 e Fax 651 736 2803 Visit our web site http www 3M com Littmann 0086 BH 3M Health Care Guer ses D 41453 Neuss Germany instructions for use 3M is a trademark of 3M Littmann is a registered trademark of 3M 34 8703 7468 2 3M 2009 All rights reserved Register your stethoscope at www littmann com SUE pp 1 22 AUS Le pp 23 44 Deutsch pp 45 66 D lia NERO ae de E T pp 67 88 tS Espafi0 RERO RR RR A A E E pp 89 110 QD Nederlands esses nennen nennen nnne nennen nnns pp 111 133 SE SY S K NNI IE I I TT pp 134 155 PEU SENE RET UTE pp 156 176 FD DOME RTE eege pp 177 197 NM SM pp 198 219 Portug s eerren iken kkn a n n an aE AE AE EE E nns pp 220 243 VUO S S m pp 244 265 3M Littmann Electronic Stethoscope Model 3200 With Ambient Noise Reduction Introduction Congratulations and thank you for choosing the 3M Littmann Electronic Stethoscope Model 3200 The Model 3200 brings you the very latest in advanced auscultation and wireless electronics technology in a highly ergonometric and easy to use format The Model 3200 s combination of Ambient Noise Reduction technology frictional noise dampening materials electronic ampli
7. d buttons to scroll through the The Model 3200 has several operational settings that can be changed using its configuration menu system Within this menu list of power settings Press and release the M button to select a setting system the and buttons are used for scrolling and the M button is used for selecting options The Filter button acts as an escape key used for returning to the previous menu or to the operating mode of the stethoscope To access the Main menu Depress and release the M button The Main menu will be displayed NOTE Only 3 options will be visible at a time All options can be viewed in sequence upon scrolling with either the or buttons m 3 i 2 D Li CONNECT EXIT DIZzCONMM gt CONHECT DIZCOHMM PECORD PLAY The power settings provide different degrees of power consumption In general the longer the stethoscope remains in PAIE an active mode the greater its power consumption The factory default is the MEDIUM level NOTE The Auto Off power SETUP management feature is further described below EXIT To select the battery type Select the BATTERY option in the Setup menu Use the and buttons to scroll through the To enter the Setup Menu Use the button to scroll down the list of Special Functions until SETUP is highlighted Select the list of battery types The LITHIUM battery is a non rechargeable cell especially recommended for low temperat
8. entre 3M Canada Inc 80 Enterprise Drive South London Ontario Canada N6N1C2 1 800 563 2921 Outside of the U S A and Canada contact your local 3M office for maintenance and repair information 18 19 GB English Declaration electromagnetic immunity The 3M Littmann Electronic Stethoscope Model 3200 is intended for use in the electromagnetic environment specified below The customer or the user of Model 3200 should assure that it is used in such an environment Immunity test IEC 60601 test level Compliance level Electromagnetic environment guidance Electrostatic discharge 6 kV contact 6 kV contact Floors should be wood concrete or ESD IEC 61000 4 2 8 kV air 8 kV air ceramic tile If floors are covered with synthetic material the relative humidity should be at least 30 Electrical fast transient 2 kV for supply lines Not applicable burst IEC 61000 4 4 1 kV for input output lines Surge IEC 61000 4 5 1 kV differential mode Not applicable 2 kV common mode Power frequency 50 60 3 A m 3 A m Power frequency magnetic fields Hz magnetic field IEC should be at levels characteristic of a 61000 4 8 typical location in a typical commercial magnetic field or hospital environment Voltage dips short lt 5 UT Not applicable interruptions and gt 95 dip in UT for 0 5 voltage variations on cycle power supply lines IEC 40 UT 61000 4 11 60 dip in UT for 5 cycle 70 UT 30 dip in UT fo
9. fication conventional bell diaphragm modes plus an extended range mode Bluetooth data transfer and an all new user interface takes you to the next level of performance and ease of use Whether you are auscultating infant pediatric or adult patients in quiet or noisy environments or picking up difficult to hear heart and body sounds you ll appreciate the technology that s been built into this latest electronic stethoscope bearing the Littmann brand Don t miss the sounds you need to hear SAFETY INFORMATION Please read understand and follow all safety information contained in these instructions prior to using this electronic stethoscope Retain these instructions for future reference U S A ONLY Caution Federal law restricts this device to sale by or on the order of a physician Explanation of Safety Related Labels and Symbols o Indicates Type B Equipment The equipment provides protection against electrical shock and electrical current leakage Applied parts are considered to be the complete chestpiece with diaphragm and binaural Consult instructions for use IPX4 Protected against splashing liquid chestpiece only This product contains electrical and electronic components and must not be disposed of using standard refuse collection Please consult local directives for disposal of electrical and electronic equipment This product and packaging does not contain natural rubber latex Indicates Category AP Eq
10. ilter Mode Mode Button Icon Icon d ls Extended i Range Mode Icon 6 Adjust Sound Amplification Level The Model 3200 sound level can be amplified in 8 increments up to 24X amplification of a non electronic cardiology level stethoscope Level 1 is equal to a non electronic stethoscope Level 9 is equal to 24X amplification of a non electronic stethoscope The greater the amplification the more bars you will see A default start up amplification level can be set using the instructions provided in the Custom Configuration section below The default setting is marked by the box on the vertical bar shown in the volume icon in the LCD display The illustration shows a default amplification setting at Level 3 pae e Increase Amplification Press button until desired amplification level is achieved e Decrease Amplification Press button until desired amplification level is achieved 6 7 Monitor Patient Heart Rate The Model 3200 detects and displays an acoustic based heart rate when presented with consistent heart sounds heart rate variation lt 10 It takes five seconds to compute the initial heart rate and updates are provided every two seconds The heart rate will then be displayed for 10 seconds after removal of the chestpiece from the patient Prior to the initial reading the display shows two dashes For heart rates outside a range of 30 199 bpm the display will also show two dashes The acoustic based heart
11. interference and 2 this device must accept any interference received including interference that may cause undesirable operation NO MODIFICATION Modifications to this device shall not be made without the written consent of the 3M Company Unauthorized modifications may void the authority granted under Federal Communications Commission rules permitting the operation of this device Industry Canada radio frequency rules and regulations IC 458A IPD3200 This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme a la norme NMB 003 du Canada EMC compliance Europe This equipment complies with the EMC requirements of the IEC 60601 1 2 Intended Use The 3M Littmann Electronic Stethoscope Model 3200 is intended for medical diagnostic purposes only It may be used for the detection and amplification of sounds from the heart lungs arteries veins and other internal organs with the use of selective frequency ranges It can be used on any person undergoing a physical assessment Operator Profile The 3M Littmann Electronic Stethoscope Model 3200 is designed to be used by anyone who wishes to listen to sounds as described in the Intended Use section above This manual provides complete information on how to operate the Model 3200 so that no additional operating training is required Functional Description The 3M Littmann Electronic Stethoscope Model 3200 picks up sounds s
12. into your ear canals When ear tips are properly positioned diaphragm will face towards your body a very comfortable acoustically sealed fit It comes with two sizes of eartips to assure a perfect fit The large eartips are pre installed Smaller eartips are included in package Please choose the set that is most comfortable for you To remove eartips pull eartips firmly away from eartube To apply new eartips push eartip firmly onto eartube to secure Remove Apply E a E a 4 3 Adjust Headset for Comfort To reduce spring tension in the headset hold each eartube at the bend near the eartips and gradually pull apart until fully extended 180 degrees m 3 To increase spring tension grasp the headset with one hand where the metal eartubes enter the plastic tubing and squeeze until the plastic tubing on one eartube touches the other Repeat as necessary AN Increase Tension 4 Turn On Off This stethoscope comes equipped with an advanced power management system NN Power Button e Manual Turn On Depress and release power button LCD display will activate indicating stethoscope is on e Manual Turn Off Depress and hold power button for two seconds LCD display will shut off indicating stethoscope is off e Auto Off with Standby Feature After manual turn on stethoscope will stay on during use but switch to a power saving standby mode after 20 seconds of inactivity LCD display wil
13. k is complete the Bluetooth link to the external device can be disconnected and the Model 3200 will return to its previous operating mode m 5 3 12 Other Operating Considerations Operating range is 22 to 104 F 30 to 40 C 15 to 93 relative humidity Storage and transport range is 40 to 131 F 40 to 55 C 15 to 93 relative humidity To extend the life of your stethoscope avoid extreme heat cold solvents and oils Remove the battery whenever the stethoscope will not be used for several months If you plan to use the stethoscope below 0 F 18 C you should use a lithium battery to insure proper function Failure to follow care and maintenance recommendations could result in damage to the internal components of the 3M Littmann Electronic Stethoscope Model 3200 Internal damage could cause malfunction of the product ranging from a slight decrease in auditory response to complete failure of the product If you experience any problems with the electronic stethoscope do not attempt to repair it yourself Please notify our 3M Health Care Service Center for directions on shipping and receiving 13 U S A Only Caution Federal law restricts this device to sale by or on the order of a physician 14 MAINTENANCE amp WARRANTY Cleaning Cleaning of stethoscope should be done between each patient use Cleaning the Chestpiece Under normal conditions it is unnecessary to remove the diaphragm for cleaning
14. l display the Littmann logo during standby mode When stethoscope diaphragm or any button is pressed LCD display settings will reappear and stethoscope will be ready to use After two hours of non use the stethoscope will leave standby mode and fully power off You may customize on time and off time to meet your own personal needs See Custom Configuration section below e LCD Display Backlight Backlight options are available for use at low ambient light levels By default depressing and releasing the power button at any time will illuminate the LCD display for 5 seconds i 2 D LLi 5 Select Filter This electronic stethoscope allows the user to select between three different digital frequency filters to better emphasize the specific patient sounds of interest e The Bellmode amplifies sounds from 20 1000Hz but emphasizes lower frequency sounds between 20 200Hz e The Diaphragm mode amplifies sounds from 20 2000Hz but emphasizes the sounds between 100 500Hz e The Extended Range mode amplifies sounds from 20 2000Hz similar to the Diaphragm Mode but provides more low frequency response between 50 500Hz The default setting is the Diaphragm filter Instructions for changing the default filter setting are given in the Custom Configuration section below To select filter Depress and release filter button as shown in diagram until desired filter mode appears on the LCD display e E Bell E E Diaphragm F
15. l situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people SISTERS Field strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the Model 3200 is used exceeds the applicable RF compliance level above the Model 3200 should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as re orienting or relocating the Model 3200 Over the frequency range 150 kHz to 80 MHz field strengths should be less than 3 V m 21 Recommended Separation Distances Between Portable and Mobile RF Communications Equipment and the Stethoscope Electronique 3M Littmann 3M Littmann Electronic Stethoscope Model 3200 Modele 3200 The Model 3200 is intended for use in an electromagnetic environment in which radiated RF disturbances are Avec r duction des bruits ambiants controlled The customer or the user of the Model 3200 can help prevent electromagnetic interference by maintaining a Introduction minimum distance between portable and mobile RF communications equipment transmitters and the
16. ociated with an electrical shock do not use the stethoscope on patients without the stethoscope s diaphragm cover in place The Model E3200 Electronic Stethoscope contains a Bluetooth Class 2 wireless data link This radio frequency data link operates at a frequency of 2 4 GHz using GFSK modulation and with a maximum transmit power of 2 5 mW 0 00250 watts The maximum radio frequency field strength generated by the stethoscope is below three volts per meter a level that is considered safe to use with other medical devices However if electromagnetic interference is encountered due to the Bluetooth wireless data link immediately move the stethoscope away from that device and or turn the Bluetooth feature OFF To reduce the risks associated with environmental contamination follow applicable regulations when disposing of this stethoscope Properly dispose of or recycle spent batteries No modification of this equipment is allowed Use only authorized 3M service personnel to repair this stethoscope Read understand and follow all the safety information on the battery package EMC Compliance FCC Intentional Radiator Certification 3M Littmann Electronic Stethoscope Model 3200 FCC ID DGFIPD3200 This equipment contains an intentional radiator approved by the FCC under the FCC ID numbers shown above This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful
17. ore entering standby Remains in standby for 5 hours before powering off Backlight remains lit for 5 seconds after pressing the power button MEDIUM Remains on full power for 20 seconds before entering standby Remains in standby for 2 hours before powering off Backlight remains lit for 5 seconds after pressing the power button Remains on full power for 10 seconds before entering standby Remains in standby for 30 minutes before powering off Backlight remains lit for 3 seconds after pressing power button 11 m 3 i 2 D LLi With AUTO OFF feature DISABLED Remains on full power for 7 minutes before entering standby Remains in standby for 5 hours before powering off Backlight remains lit for 5 seconds after pressing power button Remains on full power for 5 minutes before entering standby Remains in standby for 2 hours before powering off Backlight remains lit 5 seconds after pressing power button Remains on full power for 3 minutes before entering standby Remains in standby for 30 minutes before powering off Backlight remains lit 3 seconds after pressing power button To select the number of filter modes Select the FILTERS option in the SETUP menu Use the and buttons to scroll through the list of options With option 2 the FILTER button cycles between two filters modes bell and diaphragm With option 3 the FILTER button cycles through three filter mode
18. r 25 cycle lt 5 UT gt 95 dip in UT for 5 sec 20 Declaration electromagnetic immunity continued The 3M Littmann Electronic Stethoscope Model 3200 is intended for use in the electromagnetic environment specified below The customer or the user of Model 3200 should assure that it is used in such an environment Immunity test IEC 60601 test level Compliance level Electromagnetic environment guidance Portable and mobile RF communications equipment should be used no closer to any part of the Model 3200 including cables than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter Recommended separation distance Conducted RF 3 Vrms Not applicable d 1 2VP IEC 61000 4 6 150 kHz to 80 MHz Radiated RF 3 V m 3 V m d 1 2 V P 80 MHz to 800 MHz IEC 61000 4 3 80 MHz to 2 5 GHz 80 MHz to 2 5 GHz d 2 3 N P 800 MHz to 2 5 GHz where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer and d is the recommended separation distance in meters m Field strengths from fixed RF transmitters as determined by an electromagnetic site survey should be less than the compliance level in each frequency range Interference may occur in the vicinity of Co equipment marked with the following symbol A NOTE 1 At 80 MHz and 800 MHz the higher frequency range applies NOTE 2 These guidelines may not apply in al
19. rate display functions best when the Model 3200 is placed near the apex of the patient s heart and can be monitored while using any filter mode and or volume level If the heart rate changes from consistent to inconsistent or if there is excessive ambient noise patient movement or lung sounds during auscultation the heart rate display number will display two dashes m 5 3 EH 8 Monitor Battery Life Battery life is indicated by an icon in the LCD display m 123 The Model 3200 comes with a AA Alkaline battery Battery will provide approximately 50 60 hours of continuous use depending on the frequency of Bluetooth data transfers In a typical clinical setting this represents about three months of use PES 50 100 battery life As the battery life depletes the icon will change as follows 25 5096 battery life 5 10 25 battery life 0 10 battery life The battery icon begins to blink when only a few hours of battery capacity remains A CAUTION When the battery is completely depleted the scope becomes inoperable No sound will be transmitted without a functioning battery IMPORTANT NiMH rechargeable and Lithium batteries may also be used in the Model 3200 However battery type must be specified to ensure a reliable battery life indication see Custom Configuration section below 9 Custom Configuration To select the power setting Select the POWER option in the SETUP menu Use the an
20. release the M button The MAIN menu will be displayed Use the button to scroll to the RECORD option 2 Begin the recording Depress and release the M button The stethoscope will start recording and the LCD screen will show a recording icon ih HD 3 End the recording Depress and release the M button The stethoscope will stop recording and the recording icon will disappear from the LCD display If the time between the beginning and ending of the recording session is greater than 29 seconds only the last 29 seconds will be saved How to play back a sound track 1 Enter the playback mode Depress and release the M button The MAIN menu will be displayed Use the button to scroll to the PLAY option Select this option by pressing and releasing the M button The LCD screen will show a play icon and the sound track will loop continuously 2 End playback Depress and release the M button The stethoscope will stop playing the sound track and will return to its previous operational mode Uploading a sound track to an external device 1 Prepare the external device to receive the sound file Start the software program on the external device Consult application software for details 2 Initiate a Bluetooth connection with the Model 3200 Use the same procedure as described above for initiating real time data transfers to an external device 3 Return to operating mode When transmission of the sound trac
21. rocess the Model 3200 will make itself discoverable to other Bluetooth equipped devices Note The Personal Identification Number PIN for Bluetooth pairing is displayed in the lower left hand corner of the LCD screen 2 Select Model 3200 on external Bluetooth device Follow the pairing instructions found with your Bluetooth equipped device In general you will need to make sure that the Bluetooth mode is enabled on the device and once the Model 3200 has indicated the external device has been found you may need to confirm the connection on the external device Please remember that the distance between the Model 3200 and the Bluetooth device is limited to no more than 10 meters If pairing is successful the LCD display of the Model 3200 will show a flashing Bluetooth icon and the stethoscope will be ready for wireless operations Once the Model 3200 is connected to the external device the Bluetooth icon will stop flashing and be displayed continuously If the Bluetooth connection with the external device is subsequently lost or times out the Bluetooth icon will disappear from the LCD display 14 How to transfer real time data to an external device 1 Ensure the Model 3200 is paired with the external device 2 Depress and release the M button Select the CONNECT option by again pressing and releasing the M button The LCD screen will signal that the Bluetooth link is active The stethoscope will automatically return to operational status
22. ronment Your 3M Littmann Electronic Stethoscope Model 3200 comes with the finest service and warranty policy in the industry Emissonstest Compliane Electromagnetic environment guidance The 3M Littmann Electronic Stethoscope Model 3200 is warranted against any defects in material and manufacture for a period of two years If a material or manufacturing defect is discovered during the warranty period repairs will be made RF emissions CISPR 11 Model 3200 must emit electromagnetic energy without charge upon the return of the instrument to 3M except in cases of obvious abuse or accidental damage in order to perform its intended function Nearby For Maintenance or Repair Services electronic equipment may be affected Please include your name physical address e mail address and phone number inside with your stethoscope RF emissions CISPR 11 Model 3200 is suitable for use in all H issions IEC 61000 3 2 Not anplieabi establishments including domestic establishments UDP hd Ut appicadig and those directly connected to the public BEEN OS A voltage fluctuations flicker emissions Not applicable low voltage power supply network that supplies IEC 61000 3 3 buildings used for domestic purposes 3M Health Care Service Center 3M Bldg 502 1W 01 3350 Granada Ave N Suite 200 Oakdale MN 55128 1 800 292 6298 m 3 i In D LLi In Canada send your stethoscope directly to 3M Health Care Service C
23. s bell diaphragm and extended range Press and release the M button to select The factory default is 3 filters SETUP AUTO OFF gt FILTERS 12 To specify Bluetooth mode Select the BT COMM option in the SETUP menu Use the and buttons to scroll through the list of options The MANUAL option means that the Bluetooth link can be used for data transfers but requires user activation The AUTO option means that the Bluetooth link is continuously powered and ready to connect to an external device which it has been previously paired Press and release the M button to select an option The factory default is MANUAL SETUP T MANUAL ID AUTO m 3 To obtain model and software version information Select the ID option in the SETUP menu Use the and buttons to scroll through the list of reference numbers Press M to return to the operating mode of the stethoscope SERIAL BS04000 Boge E SW WER 22 11 05 MODEL 3t To leave the Main menu Press the Filter button or press the M button to select the EXIT option This will return the stethoscope to its normal operating state 10 Using the Bluetooth Interface The Bluetooth interface provides a means of exchanging audio data with external devices such as a Bluetooth enabled PC Audio data can be sent in near real time permitting their visual presentation recording and analysis by applications software complying with communication
24. uch as heart and lung sounds from a patient s body After amplification and filtering the sounds are sent to the user through a binaural headset The stethoscope chestpiece is designed for use with adult pediatric and infant patients The user interface for the stethoscope includes a 5 button keypad and an LCD display Sound processing is carried out with the aid of a digital signal processor Stethoscope power is provided by a single AA battery in the chestpiece A power management system is included to prolong battery life Using its Bluetooth wireless link the stethoscope can exchange audio data with an external device such as a personal computer PC rm 3 i 2 D Li Serial Number Each 3M Littmann Electronic Stethoscope Model 3200 comes with a unique serial number on the chestpiece for easy identification Please record your serial number in this manual for future reference INSTRUCTIONS FOR USE 1 Insert Battery Insert AA battery provided in package into Stethoscope Hold chestpiece in one hand while slightly twisting the battery cap approximately 25 counter clockwise Remove battery cap Insert new battery with positive end out plus sign will be visible in the battery compartment Remount battery cap twisting cap approximately 25 clockwise until locked Make sure the two marks are aligned 2 Position Headset Eartips should point in a forward direction as you insert them
25. uipment Tested for use with flammable anesthetic mixture with air 1 m 3 GB English Explanation of Signal Word Consequences A CAUTION Indicates a hazardous situation which if not avoided could result in minor injury and or property damage NOTICE Indicates a hazardous situation which if not avoided may result in property damage A CAUTION To reduce the risks associated with infection follow all cleaning and disinfecting instructions included in this manual Establish and follow a cleaning and disinfecting schedule To reduce the risks associated with very strong electromagnetic fields avoid using the stethoscope near strong radio frequency signals or portable and or mobile RF devices If you hear sudden or unexpected sounds move away from any radio transmitting antennas To reduce the risks associated with sharp edges make sure that the soft sealing eartips are snapped firmly into position as shown in this manual Use only Littmann replaceable eartips To reduce the risks associated with an incorrect result store and operate this stethoscope only as instructed in this manual As there is no acoustic non amplified mode available with this stethoscope replace the battery within two hours of the battery life icon beginning to flash in the LCD display Replace battery with only type AA Also do not immerse the stethoscope in a liquid or subject it to any sterilization processes To reduce the risk ass
26. ure operation SETUP option by pressing and releasing the M button This will display the following menu of the stethoscope The NIMH battery is rechargeable external charger required Press and release the M button to select a setting The factory default is the ALKALINE battery POWER BATTERY SET MOL SET FLTR EBCHKLITE ALKALINE LITHIUM AUTO OFF FILTERS i 2 D LLi To specify the preset default volume level Select the SET VOL option in the SETUP menu Press and release the M button to select the current volume level as default The factory default is level 3 To specify the preset default filter setting Select the SET FLTR option in the SETUP menu Press and release the M button to select the current filter as default The factory default is the diaphragm filter SETUP SET VOL gt SET FLTR BACKLITE To select the backlight setting Select the BACKLITE option in the SETUP menu Use the and buttons to scroll through the list of options Press and release the M button to select The factory default is ALWAYS The ALWAYS option will illuminate the backlight at all times at a reduced level while the stethoscope is powered on and not in standby mode The ON DMND option will illuminate the backlight for five seconds by depressing and releasing the power button The DISABLE option disables the backlight at all times and will conserve power _ t ON DHHD SC ALWAYS DISABLE 10
27. wer not listed above the recommended separation distance d in meters ETATS UNIS D AM RIQUE SEULEMENT m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output Attention La loi f d rale am ricaine limite la vente de cet instrument par et sur ordre d un m decin power rating of the transmitter in watts W according to the transmitter manufacturer NOTE 1 At 80 MHz and 800 MHz the separation distance for the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people m zr e e E a B English Explication des Etiquettes et symboles en rapport avec la s curit Appareil dit de type B cet appareil est quip d une protection contre les chocs lectriques et les coupures de courant lectrique Le pavillon complet avec diaphragme et biauriculaires sont consid r s comme tant des pi ces sous tension Consultez le mode d emploi Protection contre les claboussures de liquide pavillon uniquement Ce produit contient des composants lectriques et lectroniques et ne doit pas tre mis au rebut avec les d chets standard Veuillez consulter la r glementation locale pour la mise au rebut des quipements lectroniques et lectroniques Aucune trace de latex naturel dans le produit ni dans l emballage Appareil dit de t
28. ype AP Test pour tre utilis avec le m lange anesth sique inflammable air 22
Download Pdf Manuals
Related Search