User`s manual
Contents
1. It allows activating or deactivating the output of the second unit Note This option is available only in devices with a serial number higher than a 075511441882 J TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl T Program management 8 Set Output Services This option allows making the selection of the services that you wish to include in the output multiplex New program This option allows creating a program with the current configuration of a module or group of modules Load program lt allows loading a previously created program on a module or group of modules Delete program It allows deleting a program Device to process Current The creation or loading of a program will be applied only in the module that is currently connected All The creation or loading of a program will be applied to the whole group of connected modules Working disk With this option we have the possibility of choosing if we want to work into the internal disk or in the external storage device USB 2 0 Once the option is selected a dialog box will appear and we will be able to choose among three different options Auto The Meter decides where the data will be stored If there is external memory connected the Meter will store the data in it If not it will use the internal memory USB The Meter always will try to use the external memory connected to the USB port If this memory has not been connect2. Blinking Green Completing the initial sequence at the moment when the module gets initialized the led will turn into one of the states the operating mode Red Phase of initializing the module 2 Operative Mode Green The system is working properly Orange At least one critical event has been recorded in the module The led will only change into green when the registration of events has been read by the programmer Red Error or alert detected in the running of the device the led will be on only as long as the error alert is present Once the error or the alert disappears the led will change into orange because the error alert is stored in the registration of events 3 Programming mode When the module detects an external programmer the led will blink in the next sequence green orange red Once you leave the programming mode the led will turn into the corresponding operating mode 9 TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl Stages of transmodulator TSF 310 Cl 950 MHz DVB S QPSK DVB S2 8PSK QPSK 2150 MHz Selection of a tuned satellite transponder Transmodulation Models with a serial number lower than a 075511441882 Service 1 SERVICES Service 3 FTA FILTERING Service 4 Service 8 The tuned channels of the transponder are modulated according to the DVB T rules If the transponder has encoded channels in order to distribute them freely you have to install the
3. Bandwidth BW Diseqc Tx Mode FFT Mode Symbol rate auto FEC DVB Mode Mode 2 Auto This option allows saving and loading the configuration of the module in the PRO 201 programmer Read from module It stores the current configuration of the module in the memory of the programmer The steps to make a correct reading of the headend are specified below 1 Select the option Read from 2 Select the position of CFG 3 A window will appear and it will let module through Up Down buttons memory where you wish to save the you know that the reading made has Press OK to continue current configuration of the module been correct 12 TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl Write to module It loads in the module one of the configurations previously saved in the memory of the programmer The steps to make a correct configuration of the headend are specified below 1 Select the option Write to module 2 Select the position of the CFG 3 A window will appear and it will let through Up Down buttons Press OK memory that you wish to copy in the you know that the configuration made to continue module Please verify that the data of has been correct the selected memory correspond to the channel that you wish to copy 3 Contig In Contig option the information concerning the transmodulator is given Read log It allows reading the registered events in the mod
4. System option the information concerning the transmodulator is given EE 1 SW version info Z Date Time 3 Read LOG file 4 Delete LOG file SW version info It allows you to visualize the basic information of the module model firmware version etc Date Time Setting of the date and time of transmodulator It is appropriate to maintain these parameters set in order to have the registration of errors linked to the current time and date TSF310C1 Read LOG file It allows reading the registered events in the module Read LOG file System N 00000 04 07 14 System Ok Stakus s 00 13249228 1 SW version info 2 Date Time 3 Read LOG file 4 Delete LOG file ok SOC 1 or sven 1 Select the option Read LOG file through Up Down buttons Press OK to continue 2 A new window will appear It will show the information about the registered events in the module Press the following keys in order to scroll up and down the screen up down Delete LOG file It allows deleting all events stored until this moment Update FW It allows carrying out the firmware update from the programmer Global Update It allows carrying out the update of all the modules that are interconnected at the same time Factory default This option restores the values by default of the transmodulator 3 SD Backup This option allows saving and loading the configuration of the module in the PRO 300 programmer Rea
5. DiseqC In this option you can set the DisegC configuration A B C D and None Auto SR Auto Symbol Rate You will be able to select if the detection of the Symbol Rate is going to be Automatic On or Manual Off In Manual mode Off the value of the Symbol Rate should be fixed by the user based on the provider s information In Automatic mode On the meter will automatically identify the SR when a Satellite carrier is tuned This feature is very useful when the provider s information is unknown The SR value found will appear in the field of selection of the SR menu This value found by the meter could not correspond exactly to the real broadcast SR but to a very close value Note The Automatic Symbol Rate feature does not work when the carrier quality is very poor or and with a very low Power Level Mode This option allows selecting the standard DVB of the transponder that you want to tune Options DVB S1 DVB S2 and auto 11 TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl Terrestrial modulation Out Terr These options allow configuring the DVB T DVB H modulator of the device Modulation Output modulation format 4 QAM 16 QAM 64 QAM Invert Spectrum inversion Activate or deactivate the spectrum reverse in the modulation Gl Guard interval Allows selecting the guard interval of the modulation 1 4 1 8 1716 and 1732 BW Bandwidth Selection of the Bandwidth of the modula
6. In order to guarantee the right running of the different equipments of the installation we recommend you to provide the inputs and outputs which are not used with a 754 load OUT Accessories Programmer Field strength meter Mod PRO 201 Code 2003123 KEE Be AN Mod PRO 300 Code 2003127 20 TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl Wide band amplifier 4 7 862MHz Mod AMP 310 P Code 2003520 Parabolic antenna Chapter 2 Technical features f 1 2 2 3 3 4 5 6 7 8 8 9 9 10 1 4 1 3 1 5 2 5 3 5 4 5 DVB RS 204 188 Mode DVB T 2k 8k DVB H 2k 4k 8k PREF SOE Output channels C2 C69 Mux 1 C2 C69 Mux 2 Consecutive channel to mux 1 PRO 201 PRO 300 media Max EVO and media Max MINI Weight Note This option is available only in devices with a serial number higher than a 075511441882 Chapter 3 Declaration of conformity CONFORMITY DECLARATION WE FTE MAXIMAL DECLARE THAT THE PRODUCT TSF 310 Cl IS IN CONFORMITY WITH FOLLOWING DIRECTIVES Low Voltage Directive 2006 95 EC EMC Directive 2004 108 EC If you wish a copy of the conformity declaration please contact to the company 91 TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl ATACHMENT Depending on the configured parameters we are going to obtain one particular channel capacity output useful bit rate In order to make an estimation of this output bits rate we have to ta
7. 3 3 4 4 354 5 806 6 532 7 207 7 62 8 709 11 612 13 063 14 515 15 24 13 063 17 418 19 595 4 838 6 451 7 257 8 064 8 467 9 676 12 902 14 515 16 127 16 934 14 515 19 353 21 772 Guard Interval 5 123 6 83 7 684 8 538 8 965 10 246 13 661 15 369 17 076 17 93 15 369 20 491 23 053 23 751 5 6 7 8 21 772 22 861 24 191 25 401 25 614 26 895 26 39 27 71 Useful channel capacity 6 MHz Modulation FEC codification QPSK 1 2 2 3 Guard Interval 1 4 3 732 4 976 1 8 4 147 5 529 1 16 4 391 5 855 1 32 4 524 3 4 5 6 7 8 5 599 6 221 6 532 6 221 6 912 7 257 6 587 7 318 7 684 6 032 6 786 64 QAM Useful channel capacit Modulation 1 2 2 3 3 4 5 6 7 8 1 2 2 3 3 4 5 6 7 8 5 MHz Codificaci n FEC 7 465 9 953 11 197 12 441 13 063 11 197 14 929 16 796 18 662 19 595 1 4 8 294 11 059 12 441 13 824 14 515 12 441 16 588 18 662 20 735 21 772 1 8 Guard Interval 8 782 11 709 13 173 14 637 15 369 13 173 17 564 19 76 21 955 23 053 1 16 9 048 20358 23 751 QPSK 1 2 3 4 3 110 4 665 3 456 5 184 3 659 5 489 1 32 3 770 2 3 4 147 4 608 4 879 5 027 5 6 7 8 1 2 5 184 5 443 6 221 5 760 6 048 6 912 6 099 6 404 7 318 5 655 6 283 6 598 2 3 3 4 5 6 8 294 9 331 10 368 9 216 10 368 11 520 9 758
8. Fle TSF 310 Cl USER S MANUAL User s manual TSF 310 Cl NOTE This user s guide is adapted to software version v 0 1 47 of TSF 310 Cl dated 09 04 2014 For future software updates you can download the users guide from the following website http www ftemaximal com Chapter 1 Installation 1 1 Safety Measures 1 Never place the device next to hot sources 2 Never undergo the device to temperatures that exceed its level of operation 3 Never expose the device to leaking nor spattering 4 Never place objects that contain liquids over the device 5 Respect the ventilation slots of the device do not cover them with any kind of object 6 The space around the device must be free of objects in a minimum radius of 40cm 7 Avoid locations with possibilities of spilling liquids on the inside of the device and with important changes of temperature 8 Never open the device by yourself due to electric risk ln case of problems go always to qualified technicians 9 Never under no circumstances open the device when connected to the electrical net 10 During the handling it is better to disconnect the device from the electrical net 11 Obey the electricity security rules during the assembling Use materials that obey the current law 12 The connecting plug must be accessible in a fast and simple way to have a fast disconnection 13 Never touch the plug with wet hands Also disconnect always the device before handl
9. In the first line you have to select the high definition service and in the second line you have to select the same service but in standard definition Change in Service ID From this position you can change the PID Number of the chosen service Next it is attached the identification table NID ONID of the main satellites You will be able to find more information in the law ETSI TR 101 162 v1 2 1 Hotbird 13 E Eutelsat 13 E Astra 23 E 3 25 3 25 Astra n n 1 23 D Nilesat 7 2048 2048 Nilesat 101 Hispasat 30 W 33 33 Hispasat Network 1 9 Common Interface This option allows checking the information and configuring the parameters regarding the conditional access Cl Menu From here you can reach the menu of the card inserted in the CAM Decryption From this option you can add or remove manually the services that are being decoded by the card Remove all decrypt services From this option you can remove all the services that are decoding the conditional access card Reset CAM It allows making a reset in the CAM Watchdog CAM In cases where the encoded services stop working you can use one of the following options Deactivate No actions will me made in the CAM Update When it is detected that the decryption of the CAM has been lost the rights will be sent systematically until the decryption gets back Reset As soon as the loss of decryption of the CAM is detected a reset will be made Both Once
10. of the device Deactivate output H allows activating or deactivating the output of transmodulator Switch output to CW It allows activating or deactivating the DVB T DVB H modulation allowing visualizing the carrier without modulation in the selected frequency 6 System This option provides information of the transmodulator System logfile In this field are indicated the registered events in the module Read log It allows reading the registered events in the module Clear log It allows deleting all events stored until this moment Export log to USB It allows you to export all events registered to the connected USB device 6 TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl NM low Limit dB An event of error will be recorded when the value of Noise Margin is lower than the set value NM high limit dB Once the event of error is recorded Noise Margin lt Limit Lower NM this will be Noise Margin value that will have to be exceed so the module stops being in error Clear log all devices It allows deleting the events report of all the interconnected modules Factory default This option restores the values by default of the transmodulator System information It allows you to visualize the basic information of the module model no of series firmware version etc Settings This option allows saving and loading the configuration of the module carrying out firmware updat
11. the loss of decryption of the CAM is detected the rights will be sent several times until the decryption gets back In cases where it does not get back the module will make a reset of the CAM CAM Reset after It makes a reset of the CAM alter a set period of time Options 0 5 min 10 min 15 min Cl daily reset time Time when the CAM is resetting when this option is enabled Activated slots This option decides the number of slots used Options 1 only and 1 and 2 10 TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl PRO 201 f Note From PRO 201 programmer you can only carry out the programming of a single module in order to carry out the programming of several modules at the same time you have to use a mediaMAX EVO or mediaMAX MINI series field strength meter When you connect the PRO 201 programmer it will proceed to recognize the module and to show the main menu In the main menu are shown the different options for configuring the transmodulator We have to use the Up and Down buttons of the keyboard in order to move to the different options and to get into the submenus we have to press OK button 1 Manual Inside the manual menu there are specified the different options for setting up the input output and modulation parameters Nota If you have a module with a serial number higher than 075511441882 it will allow you to choose between two units with an only device conn
12. you want to delete with the Left Right keys Then press OK over Rem in order to remove it or press OK over All in order to delete all the services Press OK to finish 19 TSF 310 CI version_en_3 0 FTE maximal User s manual TSF 310 Cl Cl menu From this option the access to the CAM menu is allowed select the slot is necessary Reset CAM This option allows the CAM initialization select the slot is necessary 1 5 Accessories and example of installation Example of installation Models with a serial number lower than a 075511441882 Models with a serial number higher than a 075511441882 OS 100 OS 100 B B d 4 1NC544 M pa 1NC544 RE NS a lt A SPS 310 SPS 310 TSF 310 Cl 47 MHz 47 MHz TSF 310 Cl Installation that consist of 6 TSF 310 Cl and that will allow tuning channels up to 6 different transponders and to distribute them through a TV network in DVB T The new models TSF 310 Cl with twin output allow distributing up to 12 multiplex in the installation The distributed channels need a terrestrial receiver in order to be decoded The number of modules TSF 310 Cl that can be fed by the power supply SPS 310 will depend on the number of CAM s and their consumptions Ifthe total amount of modules that are connected to the power supply have two CAM s inserted the SPS will be able to feed only 5 modules In any other case the power supply will be able to feed 6 modules
13. 00 programmer it will proceed to recognize Main menu the module and to show the main menu In the main menu are shown the different options for configuring the 2 System transmodulator 3 5D Backup We have to use the Up and Down buttons of the keyboard in order to 4 CAM move to the different options and to get into the submenus we have to press OK button TSFS10CI 1 I O configuration Inside the I O configuration menu there are specified the different options 1 0 configuration for setting up the input output and modulation parameters In order to move around the different options we have to use the Up and Down buttons of the keyboard Click on OK to edit the 2 0ut Terr selected parameter and Right Left for changing it Once it is Zeie TY configured press Cancel A Services Contigo TSFSLOCI Every time an option is selected the output Mux that we want to Puse configure should be selected 2 Mies 1 TSFSLOCI Satellite input Input Sat In these options you will be able to configure the input parameters of the Input Sat satellite signal 1 LO Freq 2 Freq LO freq Local oscillator Selection of the local oscillator that you wish to 3 symbol Rate use Fl KU C K9750 K10000 K10600 K10700 K10750 K11250 4 antenna K11300 and K11325 Freq Input Frequency MHz Transponder frequency that you wish to tune In order to introduce the frequency press the OK bu
14. 10 978 12 197 7 540 10 053 11 310 7 8 1 2 2 3 3 4 5 6 7 8 10 886 9 331 12 441 13 996 15 551 16 329 Note Only applicable for DVB H 93 12 096 10 368 13 824 15 551 17 279 18 143 TSF 310 Cl 12 807 10 978 14 637 16 466 18 296 19 211 version_en_3 0 13 195 FTE maxima ESPANA Corrals Nous 77 Pol Industrial Can Roqueta 08202 Sabadell Barcelona Espa a Tel 34 93 729 27 00 Fax 34 93 729 30 73 infofOftemaximal com www ftemaximal com DEUTSCHLAND Zweigniederlassung Deutschland Furstenhof 68 59368 Werne Amtsgericht Dortmund HRB 21674 Ust ID Nr DE243384161 Tel 49 2389 92419 0 Fax 49 2389 92419 25 info ftemaximal de www ftemaximal com FRANCE Fte maximal France SAS 7 avenue du Pont de Tasset 74960 MEYTHET Tel 33 4 50 68 80 17 Fax 33 4 50 68 84 68 fte ftemaximal fr www ftemaximal com PORTUGAL Rua Jos Carlos Ary dos Santos A das Lebres Loures 2660 173 Santo Ant o do Tojal Tel 00 351 21 983 87 00 Fax 00 351 21 983 87 09 ftemaximal ftemaximal pt www ftemaximal com Fle maximal ITALIA Via Edison 29 42040 Calerno di Sant llario d Enza RE Tel 00 39 05 22 90 97 01 Fax 00 39 05 22 90 97 48 infoOfte it www ftemaximal com UNITED ARAB EMIRATES P O Box 262442 BOUTIQUE VILLA 06 2nd Floor BEHIND KNOWLEDGE VILLAGE MEDIA CITY Dubai UAE Tel 00 971 4 4385509 Fax 00 971 4 4385508 info ftemaximal com w
15. 4 5 6 y 7 8 For example in a FEC 2 3 relation we will find 2 information bits and 1 redundant bit Modulation Output modulation format 4 QPSK 16 16 QAM 64 64 QAM Advanced settings Mode Selection of the modulation standard DVB T and DVB H codification and modulation In the Attachment you will find all the information related to the resulting useful Note The output useful bits rate will depend on the following parameters Bandwidth guard interval FEC bit rate in each configuration 5 Set Output channel In this option you can configure the different parameters of the cable signal Channel standard H allows you to select the channelling of the cable signal standards Options BG BG PAL BG IT LL M NTSC PAL M PAL N PAL DK PAL BB_AU DK PAL L PAL Channel Output channel of the cable modulation When you select the output channel the field Frequency MHz will be modified automatically adapting itself to the selected channel Options C2 C69 Frequency MHz Output frequency of cable modulation When you modify this field the field Channel will be also modified indicating the channel equivalent to the selected frequency in the case that this frequency corresponds to the frequency of a channel Options 47 862 MHz Level Regulation of the output level of the modulated signal Options 0 15dB Calibration Allows the realization of two tests in order to verify the correct running
16. M of it A feature of this equipment is its modulator in Vestigial Side Band or VSB This modulation can be used to distribute adjacent channels in one distribution without any interference problem Each module has one Loop connector to cascade several modules at input and a Mix connector to do same in output channels The output channel is selectable between C2 and C69 All parameters are programmed by the means of PRO 201 PRO 300 or the EVO or MINI series of field strength meter and they are monitored in the display of programmer or in the screen of field strength meter TSF 310 Cl has two Common Interface slots TSF 310 Cl 1 Two colored led It indicates the different states of the device 2 Cl Common Interface 3 OUT This connector supplies the modulated channel according to the selected standard in the module and mixes it with all the signals that it receives through the MIX connector z 4 MIX Input of mixing of the module 5 LNC IN To connect to the LNC or to the LOOP OUT output of the previous module 2 g 6 LOOP OUT To connect to the ANT IN input of the next module 7 RS 232 Ethernet connector to cascade modules with the RCM 310 telecontrol unit with the RJ45 RJ45 cable provided 8 PRO 201 Ethernet connector to make the programming with the programmer A 9 DC connectors lt has two connectors for connecting between modules 3 4 States of two colored leds 1 Initialization mode Green main application charged
17. PCMCIA subscriber card in the Common Interface slot Models with a serial number higher than a 075511441882 Service 1 Service 3 Service 5 Service 7 Service 8 Service 1 Service 2 Service 3 Service 4 Service 5 Service 6 Service 7 Service 8 Service 9 The tuned channels of the transponder are modulated according to the DVB T rules in two multiplex In cases where the transponder has encoded channels if you wish to distribute them freely you will have to link a PCMCIA subscriber card to each one of the two outputs of the multiplex Models with a serial number lower than a 075511441882 Models with a serial number higher than a 075511441882 DVB T COFDM DVB T COFDM 882 MHz 862 MHz Contiguration of the channel and the output parameters of the multiplex The channel of the second multiple will be set by default as the consecutive channel of the one in the first multiplex Contiguration of the channels and output parameters 1 4 Programming TSF 310 Cl has two ethernet connectors In order to make the programming of the module you have to connect the corresponding programmer to PRO 201 connector You can make the programming through the PRO 201 PRO 300 programmers and also through the mediaMAX EVO and mediaMAX MINI field strength meter 1 4 1 Programming modes Through PRO 201 or PRO 300 the programming is made module by module With mediaMAX EVO mediaMAX MINI field strength meter you can carry ou
18. ameters of the terrestrial out py signal E 1 RF Channel 474000 RF Channel MHz Output frequency of terrestrial modulation In order to 2 RF Level 013 introduce the frequency press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value TSF310CI Options 47 862 MHz RF Level Regulation of the output level of the modulated signal Options O 15dB Summary table Satellite input Terrestrial output TV output LO frequency Modulation RF Channel Input Frequency Invert Spectrum Inversion RF Level Symbol Rate Guard Interval Gl Antenna Bandwidth BW Diseqc Tx Mode FFT Mode Symbol rate auto FEC DVB Mode Mode Services configuration This option allows configuring the features of the output services Services config Output services This option allows making the selection of the services that 5 Output serv Name you wish to include in the output multiplex 3 LCN Once you have tuned a transponder and you have selected the DVB T DVB H modulator configuration you can make the assignment of the services that are going to be included in the output multiplex TSF310C1 4 Network options 16 TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl Adding Services Output services 1 Add services 2 Delete ser
19. cting the standard DVB of the transponder that you want to tune Options DVB S1 DVB S2 and AUTO 15 TSF 310 Cl version_en_3 0 FTE maxima User s manual TSF 310 Cl Terrestrial modulation Out Terr These options allow configuring the DVB T DVB H modulator of the device Our tere Modulation Output modulation format 4 QAM 16 QAM 64 QAM Invert Spectrum inversion Activate or deactivate the spectrum reverse in 1 Modulation the modulation 2 invert Gl Guard interval Allows selecting the guard interval of the modulation 3 GI 1 4 1 8 1 16 and 1 32 4 Bandwith BW Bandwidth Selection of the Bandwidth of the modulated signal 8MHz 7MHz 6 MHz and SMHz The BMHz option is only supported by DVB H standard Tx Mode FFT Mode 8K 4K and 2k The 4k option is only supported by DVB H standard FEC Indicates the relationship between the redundant bits and the transmitted information bits 1 2 2 3 3 4 5 6 and 7 8 For example in a FEC 2 3 relation we will find 2 information bits and 1 redundant bit Mode Selection of the modulation standard DVB T and DVB H TSFSLOCI codification and modulation In the Attachment you will find all the information related to the resulting useful bit Note The output useful bits rate will depend on the following parameters Bandwidth guard interval FEC rate in each configuration Output configuration Out TV In these options you can configure the output par
20. d from module It stores the current configuration of the module in the memory of the programmer The steps to make a correct reading of the headend are specified below SD Backup 1 Read from module 2 Write to module Read from module Read from module Mux 3 0 Freq 10992 CUTIT CFG 00 Sr22 1500 Freq 474000 Operation finish GSD SOO TSFSLOCI ABS Ss OKO IE 1 Select the option Read from module through Up Down buttons Press OK to continue 2 Select the position of CFG memory where you wish to save the current configuration of the module 3 A window will appear and it will let you know that the reading made has been correct 18 TSF 310 CI version_en_3 0 FTE maximal User s manual TSF 310 Cl Write to module It loads in the module one of the configurations previously saved in the memory of the programmer The steps to make a correct configuration of the headend are specified below SDE 1 Read from module 2 Write to module TSFJLOCI 1 Select the option Write to module through Up Down buttons Press OK Write to module CFG 00 EE 1500 Fregq 474000 Max s 18 Freq 10992 Output TSFSLOCI 2 Select the position of the CFG memory that you wish to copy in the Write to module Operacion rinish TSFSLOCI 3 A window will appear and it will let you know that the configuration made to continue module Please verify that the data of has been correct the selecte
21. d memory correspond to the channel that you wish to copy 4 CAM This option allows selecting which services are decrypted and enabling the access to the CAM parameters CAM 1 Decrypt services 2 C menu 3 Reset CAM ons oer Decrypt services From this option you can add or remove manually the services that are being decoded by the card Adding services Decrypt services Decrypt services Decrypt services 1 Add services 2 Delete services PID 200500 1 Add ee ek 1 Mux 0 S5lot 0 NEOX 2 Mux 1 Slot 1 TSFJLOCI TSFSLOCI TSFSLOCI 1 Select the Mux and Slot option where the services will be added through Up Down buttons Press OK to continue 2 Select the option Add services through Up Down buttons Press OK to continue 3 Select one of the multiplex services you want to add through Left Right keys and select the Add button to include the service in the multiplex Or select All in order to add all the services Press OK to finish Deleting services Decrypt services Decrypt services Decrypt services PID 300500 2 All 1 Add services NEOX 2 Delete services l Mux O0 Slor 0 2 Mux 1 Slot 1 TSESLOCI TSE SLOCI Mux 1 TSFSLOCI 1 Select the Mux and Slot option where the services will be deleted through Up Down buttons Press OK to continue 2 Select the option Delete services through Up Down buttons Press OK to continue 3 Select the service
22. de 2 3 FEC 1 4 guard intervals 64QAM constellation for an 8 MHz channel and using the previous formula you will get the following channel useful capacity Tb 19 905 Mbps util Note As you select a configuration with a higher output channel capacity the protection grade against mistakes gets proportionally decreased Next it is shown the channel capacity for systems without hierarchy in all the cases of constellation guard interval and codification relation for transmissions of 8MHz 7MHz 6MHz y 5MHz DVB H The useful capacity channel is identical for modes 2k 4k DVB H and 8k 99 TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 C Useful channel capacity 8 MHz Modulation QPSK 16 QAM 64 QAM FEC codification 172 2 3 3 4 5 6 7 8 1 2 2 3 3 4 5 6 1 4 4 976 6 635 7 465 8 294 8 709 9 953 13 271 14 929 16 588 1 8 5 529 7 373 8 294 9 216 9 676 11 059 14 745 16 588 18 431 Guard Interval 1 16 5 855 7 806 8 782 9 758 10 246 11 709 15 612 17 564 19 516 7 8 1 2 2 3 17 418 14 929 19 906 19 353 16 588 22 118 20 491 17 564 23 419 20 107 21 112 18 096 24 128 3 4 5 6 7 8 Useful channel capacity 7 MHz 22 394 24 882 26 126 24 882 27 647 29 029 26 346 29 273 30 737 27 144 31 668 Modulation QPSK 16 QAM FEC codification 1 2 2 3 3 4 5 6 7 8 1 2 2 3 3 4 5 6 7 8 1 2 2
23. e or making an adjustment of the time and date of the module Clock Alias Set Date and time Setting of the date and time of transmodulator It is appropriate to maintain these parameters set in order to have the registration of errors linked to the current time and date Set date time all devices Loading the current date and time of the module in the rest of interconnected modules Write alias It allows you to assign a name alias to the module you are programming Option only available when the Alias Auto option is configures as none manual mode Auto Alias It allows configuring the name alias of the modules automatically Options Channel Frequency Service None Upgrade Send Firmware from USB It allows carrying out the firmware update from the USB device Send firmware to all It allows carrying out the update of all the modules that are interconnected at the same time Configure all devices Input values to all devices It allows copying the current input configuration in all the interconnected modules Modulator values to all devices It allows copying the configuration of the current modulator in all the interconnected modules Output values to all devices It allows copying the current output configuration in all the interconnected modules Factory default to all devices It allows making values by default to all the interconnected modules Activate next output
24. ected to the programmer Unit 1 Mux O or Unit 2 Mux 1 1 This field shows the type of parameter that is selected at the moment Options Input Sat Out Terr Out TV 2 This field shows the parameter that is selected In order to move around the different options we have to use the Up and Down buttons of the keyboard Click on OK to edit the selected parameter and Right Left for changing it Once it is configured press OK N Satellite input Input Sat In these options you will be able to configure the input parameters of the satellite signal LO freq Local oscillator Selection of the local oscillator that you wish to use Fl KU C K9750 K10000 K10600 K10700 K10750 K11250 K11300 and K11325 Freq Input Frequency MHz Transponder frequency that you wish to tune In order to introduce the frequency press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Symbol Rate Symbol speed required by the transponder In order to introduce the symbol rate press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Antenna Feeding tone towards the LNC Options OV 13V 18V 22kHz 18V 18V 22KHz 13V AUT 18V AUT
25. ed an error message will be shown reminding that there was an error storing the data and it will be not stored Internal Always the internal memory is used to store the data Load programs from USB This option allows importing programs from a USB memory to the field strength meter Before using this option you must connect a USB memory Save programs to USB This option allows copying the programs stored in the external USB 2 0 storage device Write Alias It allows saving the alias of the module in the program Options Yes No Add Remove services It allows adding the services to the multiplex and also removing the ones previously included The lower bar informs about the available space in the output multiplex As you add more services the space available will decrease Once you have tuned a transponder in the Input Set Up section and you have selected the DVB T DVB H modulator configuration in the Modulator Set Up section you can make the assignment of the services that are going to be included in the output multiplex Adding Removing services Adding services 1 Select Service to add option 2 Select one of the transponder 3 Once you have chosen the services you want to add service select the Add Rem button to include the service in the multiplex A Note It is not recommended to exceed the 85 of the maximum capacity of the multiplex due to the possible variability of the bits
26. edition mode is on placing the cursor over the digit the value could be changed by means the bottoms Up Down One time finished the changes are saved pressing OK LCN The LCN function allows assigning automatically a predetermined position to each one of the services of the multiplex This function will allow the users who have a receiver with LCN support to make the ordination of channels automatically Select a channel through Left Right buttons and introduce the position Press the OK button and the cursor will be placed over the number With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the changes A 00000 Rai Movie TSF310 Note If in the existing installation there are already services that have LCN system you will have to configure the position of the module services in order to avoid conflicts with other net services ES TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl Network Option This option allows adjusting the identification parameters of multiplex Network name Associated name to the network TSID Identification value of Transport Stream Give a different value of TSID for each output multiplex configured is recommended Network options 1 Network name PS ED SINE 4 ONID NID Identification value of the network ONID Original identification value of the network TSE310CI 2 System In
27. eter will automatically identify the SR when a Satellite carrier is tuned This feature is very useful when the provider s information is unknown The SR value found will appear in the field of selection of the SR menu This value found by the meter could not correspond exactly to the real broadcast SR but to a very close value Note The Automatic Symbol Rate feature does not work when the carrier quality is very poor or and with a very low Power Level DVB This option allows selecting the standard DVB of the transponder that you want to tune Options DVB S1 DVB S2 and AUTO LNB Supply In this option you can set the parameters concerning the LNB RF IN Voltage 13V 18V and Off 22 kHz Tone Off On and Auto 5 TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl DisegC Switch A B C D and Off 4 Modulator Set Up This option allows configuring the DVB T DVB H modulator of the device Bandwidth Selection of the Bandwidth of the modulated signal 8MHz 7MHz 6MHz and SMHz The 5MHz option is only supported by DVB H standard FFT Mode 8K 4K and 2k The 4k option is only supported by DVB H standard Spectrum inversion Activate or deactivate the spectrum reverse in the modulation Guard interval Allows selecting the guard interval of the modulation 1 4 1 8 1 16 and 1 32 FEC Indicates the relationship between the redundant bits and the transmitted information bits 1 2 2 3 3
28. ing the connections 14 Never put any heavy object over the device since it could get damaged 15 If the device is going to remain some time without use it is recommendable to disconnect it from the electrical net 16 The repairmen and the maintenance of the device must be done by TV and radio specialised technicians 1 2 Box content 9 x Link F male F male DC Cable TSF 310 Cl Cable 12 cm PIN to PIN RJ45 RJ45 Stopper 1 TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl The models with a serial number higher than 075511441882 will be provided with a double DVB T output that will allow distributing the channels of the tuned transponder in two consecutive multiplex In order to configure the device we will have two selectable modules The configuration of the input transponder is the same for both modules all the other options of configuration are independent With the following exceptions The output channel of the second module will be set automatically as the consecutive channel after the one configured in the first module The output level of the multiplex will be set by the output level configured in the first module 1 3 Description and connections The module TSF 310 Cl is used for the reception of free channels that obey the DVB S DVB S2 standards Each module allows the reception of a complete transponder in DVB S QPSK DVB S2 QPSK 8PSK and the subsequent modulation in DVB T COFD
29. ke into account the following parameters Symbol duration Ts For signals of 8 MHz Mode 8K 6817 carrier 4K 3409 carrier 2K 1705 carrier Symbol duration 224 us us For signals of 7 MHz 8K 6817 carrier 4K 3409 carrier 2K 1705 carrier Symbol duration 1024 us 512 us 256 us Guard Interval 1716 1 32 1 4 1 16 1 32 1 4 1716 1 32 Duration 256us 128us 64us 32us 128us 64us 32us 16us 64us 32us 16us 8us For signals of 6 MHz Mode 8K 6817 carrier 4K 3409 carrier 2K 1705 carrier For signals of 5 MHz 8K 6817 carrier 4K 3409 carrier 2K 1705 carrier Symbol duration 1433 6 us 597 3 us 298 6 us p08 Gus Modulation Modulation QPSK 16 QAM 64 QAM Number of bits per symbol 2 4 6 FFT Mode 2K Data carriers 6048 3024 1512 Total carriers 6817 3409 1705 Bits rate calculation total Tb orai fs b L Where Fs Symbols frequency symbols sec fs 1 Ts Ts Symbol duration Symbol Time Guard Interval time b Number of bits per symbol depending on the modulation L Number of data carriers depending of FFT mode Bits rate calculation useful Tb vit In Codif zc i Codif re ed Salomon FEC Cod FEC Codification 1 2 2 3 3 4 5 6 7 8 Reed Salomon Cod Codification made by the means of Reed Salomon algorithm 188 204 Case study example For example in the case of a DVB T transmission in Spain the configured parameters would be the following 8k mo
30. oid conflicts with other net services Decrypt services From this option you can add or remove manually the services that are being decoded by the card Delete services Add services Reset CAM It allows making a reset in the selected CAM Cl menu From this option the access to the CAM menu is allowed select the slot is necessary Date Time Setting of the date and time of transmodulator It is appropriate to maintain these parameters set in order to have the registration of errors linked to the current time and date SW version info It allows you to visualize the basic information of the module model firmware version etc Num Muxes Slots It configures the number of output multiplex Options 1 or 2 Global Update It allows carrying out the update of all the modules that are interconnected at the same time Note If the serial number of the device is higher than 075511441882 you have to select in which one of the two modules you want to make the configuration in each case This option is available only in devices with a serial number higher than a 075511441882 14 TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl PRO 300 out the programming of several modules at the same time you have to use a mediaMAX EVO or mediaMAX Note From PRO 300 programmer you can only carry out the programming of a single module in order to carry MINI series field strength meter When you connect the PRO 3
31. p Down buttons Press OK services you want to add through you know that the operation made has to continue Left Right keys and select the Add been correct button to include the service in the multiplex Delete Services 1 Select the option Delete services 2 Select the service you want to 3 A window will appear and it will let through Up Down buttons Press OK delete with the Left Right keys Then you know that the operation made has to continue press OK over Rem in order to been correct remove it or press OK over AT in order to delete all the services of the multiplex Note It is not recommended to exceed the 85 of the maximum capacity of the multiplex due to the possible variability of the bits rate of the inputs services LCN The LCN function allows assigning automatically a predetermined position to each one of the services of the multiplex This function will allow the users who have a receiver with LCN support to make the ordination of channels automatically Select a channel through Left Right buttons and introduce the position Press the OK button and the cursor will be placed over the number With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the changes Note If in the existing installation there are already services that have LCN system you will have to configure the position of the module services in order to av
32. rate of the inputs services 8 TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl Excessive capacity It is recommended to remove services Recomendad capacity lower to 85 Removing services 1 Select the Service to remove 2 Select one of the transponder 3 Once you have chosen the service option services you want to remove select the Add Rem button to remove the service in the multiplex Remove all services It allows removing all the services included in the multiplex Modity LCN The LCN function allows assigning automatically a predetermined position to each one of the services of the multiplex This function will allow the users who have a receiver with LCN support to make the ordination of channels automatically Note If in the existing installation there are already services that have LCN system you will have to configure the position of the module services in order to avoid conflicts with other net services Bandwidth limitation It allows selecting the of the capacity of the output channel Auto service addition On It selects the services automatically when an input carrier is tuned and when the list of selected services is empty The receiver will have this state by default Always It selects the services automatically every time a new input carrier is tuned This state is only recommended to be used for making test in the module Off The automatic mode i
33. s deactivated the services have to be manually selected Advanced settings Network It allows making the adjustment of the identification parameters of the multiplex TS ID Transport Stream identification value It is recommended to configure a value different from TS ID for each one of the output multiplex configured Net ID Net identification value Original Net ID Original net identification value Network Name Name associated with the net Tables It allows modifying the value of the following information tables of the DVB NIT SDT and PAT Services 9 TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl Services Change service name It allows changing the name of the service manually In order to do so please choose the service in the first line and then write the new name in the second line Then you have to press modify in order to save the changes HDSimulCast In cases where we receive in an installation the same channel in high definition and in standard definition the HD Simulcast function allows to exchange the position of the LNC of both channels If the user has a device compatible to HD Simulcast and the module has been correctly configured when tuning the standard definition channel it will move to its position in high definition automatically This option allows modifying manually the position of the LCN exchanging the standard position into the high definition position
34. t the programming of all the modules consecutively as long as they are interconnected with each other through the RJ 45 cable supplied with each unit TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl 1 4 2 Programming Below you will find the steps to follow in order to make the programming both from corresponding EVO and MINI field strength meter as well as from PRO 201and PRO 300 mediaMAX EVO mediaMAX MINI In order to start programming the TSF 310 Cl transmodulator you will have to go to Tools option through the key 8 of your field strength meter and to select the Transmodulator Prog option Then it will proceed to recognize the module and to show the main menu In the Transmodulator Prog are shown the different configuration options that this tool offers 1 Select Device The field strength meter allows carrying out the programming of one or several transmodulators from an only transmodulator Without interconnection of modules An only module connected Interconnection of several modules you can select which module you wish to program 4 TSF 310 Cl version_en_3 0 FTE maximal 2 Device Status In the option Device Status are specified the main parameters of the module at this moment 3 Set Front End In this option you will be able to configure the input parameters of the satellite signal A User s manual TSF 310 CI If you have a module wi
35. ted signal 8 MHz 7 MHz and 6 MHz and 5MHz The 5 MHz option is only supported by DVB H standard Tx Mode FFT Mode 8K 4K and 2k The 4k option is only supported by DVB H standard FEC Indicates the relationship between the redundant bits and the transmitted information bits 1 2 2 3 3 4 5 6 y 7 8 For example in a FEC 2 3 relation we will find 2 information bits and 1 redundant bit Mode Selection of the modulation standard DVB T and DVB H codification and modulation In the Attachment you will find all the information related to the resulting useful bit i Note The output useful bits rate will depend on the following parameters Bandwidth guard interval FEC rate in each configuration Output configuration TV output In these options you can configure the output parameters of the terrestrial signal RE Channel MHz Output frequency of terrestrial modulation In order to introduce the frequency press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Options 47 862 MHz RF Level Regulation of the output level of the modulated signal Options O 15dB Summary table Satellite input Terrestrial output TV output LO frequency Modulation RF Channel Input Frequency Invert Spectrum Inversion RF Level Symbol Rate Guard Interval Gl Antenna
36. th a serial number higher than 075511441882 it will allow you to choose between two units with an only device connected to the programmer Unit 1 or Unit 2 Front End It indicates whether the module is hooked or without signal Input bit rate Transfers of data in the satellite tuner input Output bit rate Transfer of data in the module output BER before and after Viterbi H indicates the error rate of bits of the input signal before and after the correction produced by Viterbi algorithm MER Parameter that indicates the quality of the input modulated digital signal expressed in dB Noise Margin It indicates the difference between the value of current C N and the value of C N at the point of pixilation of the signal that is the quantity of dB of C N measure that are needed to lose the input signal Temperature lt indicates the current temperature of the module in degrees Local oscillator Selection of the local oscillator that you wish to use Fl KU C K9750 K10000 K10600 K10700 K10 750 K11250 K11300 and K11325 Frequency MHz Transponder frequency that you wish to tune Symbol speed Symbol speed required by the transponder Auto symbol rate You will be able to select if the detection of the Symbol Rate is going to be Automatic On or Manual Off In Manual mode Off the value of the Symbol Rate should be fixed by the user based on the provider s information In Automatic mode On the m
37. tton and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Symbol Rate Symbol speed required by the transponder In order to introduce the symbol rate press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Antenna Feeding tone towards the LNC Options OV 13V 18V 22kHz 18V 18V 22KHz 13V AUT 18V AUT DiseqC In this option you can set the DisegC configuration A B C D and None Auto SR Auto Symbol Rate You will be able to select if the detection of the Symbol Rate is going to be Automatic On or Manual Off In Manual mode Off the value of the Symbol Rate should be fixed by the user based on the provider s information In Automatic mode On the meter will automatically identify the SR when a Satellite carrier is tuned This feature is very useful when the provider s information is unknown The SR value found will appear in the field of selection of the SR menu This value found by the meter could not correspond exactly to the real broadcast SR but to a very close value TSESILO Mux 0 Note The Automatic Symbol Rate feature does not work when the carrier quality is very poor or and with a very low Power Level Mode This option allows sele
38. ule 1 Select the option Read LOG file 2 Press OK again to show the log file 3 A new window will appear It will through Up Down buttons Press OK show the information about the to continue registered events in the module Press the following keys in order to scroll up and down the screen up down Delete LOG file It allows deleting all events stored until this moment Factory default This option restores the values by default of the transmodulator Update FW It allows carrying out the firmware update from the programmer Net name Name associated to the net TSID Identification value of Transport Stream Give a different value of TSID for each output multiplex configured is recommended NID Net identification value ONID Original Net identification value Output services This option allows making the selection of the services that you wish to include in the output multiplex Once you have tuned a transponder and you have selected the DVB T DVB H modulator configuration you can make the assignment of the services that are going to be included in the output multiplex Adding Removing services For this is necessary to select the Mux where the services will be added or removed 13 TSF 310 Cl version_en_3 0 FTE maximal User s manual TSF 310 Cl Add Services 1 Select the option Add services 2 Select one of the transponder 3 A window will appear and it will let through U
39. vices BW usage IESSE 1 Select the option Add services through Up Down buttons Press OK to continue Deleting Services Output services 1 Add services 2 Delete services BW usage ESESIOET 1 Select the option Delete services through Up Down buttons Press OK to continue A Output services PID 201105 1 Add RAI 2 BW usage 072 TSESLOCLI Mux 0 2 Select one of the multiplex services you want to add through Left Right keys and select the Add button to include the service in the multiplex Output services PID 00900 RAI MOVIE 2 Ad E BW usage 072 TSESLOCI Mux 0 2 Select the service you want to delete with the Left Right keys Then press OK over Rem in order to remove it or press OK over All in order to delete all the services of the multiplex Output services Operation finish Lops VOCE 3 A window will appear and it will let you know that the operation made has been correct Output services Operation mina isla Hehehe 3 A window will appear and it will let you know that the operation made has been correct Note It is not recommended to exceed the 85 of the maximum capacity of the multiplex due to the possible variability of the bits rate of the inputs services Output service name This option allows editing the services name and changing it By means the bottoms Left Right the service to edit is selected pressing OK the
40. ww ftemaximal com
Download Pdf Manuals
Related Search