Home

NX-4 Manual

1. aFae ac AC input Connect to a 16 5V 25 40 or 50 VA Class Ui approved transformer Connect negative lead of low current device relay LED install 1K Q resistor in series with LED etc Connect positive lead of device to KEYPAD Current is limited to 250mA when output is negative and 2504A when output is positive If used as a siren output default the speaker rating should be 15 watt at 8 or 16 ohm or 30 40 watt at 4 8 or 16 ohms If voltage output is selected in location 37 this output becomes voltage output 12VDC 1 Amp maximum load NOTE A 3 3K O resistor may be required across the bell terminals when a 12 VDC siren is used If no resistor is used you may experience voltage leakage into the siren which will cause these devices to output a small signal COM Connect negative wire of siren speaker or voltage output devices SMOKE Smoke detector power 12VDC 250 mA maximum For those jurisdictions which allow the Priority zone to be used with smoke detectors Connect negative lead of low current device relay LED install 1K Q resistor in series with LED etc Connect positive lead of device to KEYPAD Current is limited to 250mA when output is negative and 2504A when output is positive KEYPAD DATA Connect to the data terminal on the keypads and the expanders MAXIMUM 8 keypads 1 other device COM AUX PWR Connect to the Common terminal on the keypads expanders and other power devices
2. 3 Quick Arm LED extinguish enable Open Close Re Exit Require user code for bypassing zones Bypass Auto Bypass Bypass sounder alert Restore Silent Panic AC power low battery sounder alert Trouble Audible Panic Enables bypass toggle Tamper Auxiliary 1 Enables silent auto arm Cancel Auxiliary 2 Enables automatic instant Recent Closing Multi Keypress Tamper Reserved Exit Error 24 17 ENTRY EXIT TIMERS Cc oU L ON P x OD OY Ui UW o N OU QON P D sw QU P ONP Um a7 zones 1 8 ZONE TYPES macnn eeeseeez DAY ZONE RESERVED 24 HOUR AUDIBLE INTERIOR FOLLOWER W CROSS ZONE ENTRY EXIT DELAY 1 INSTANT ENTRY GUARD FOLLOWER W AUTO BYPASS DISABLED ENTRY EXIT DELAY 1 W GROUP BYPASS INTERIOR FOLLOWER W AUTO BYPASS INTERIOR FOLLOWER W GROUP BYPASS INSTANT INSTANT W GROUP BYPASS 24 HOUR SILENT ENTRY EXIT DELAY 1 W TAMPER FIRE INTERIOR FOLLOWER W TAMPER amp AUTO BYPASS ENTRY EXIT DELAY 2 INSTANT W TAMPER 24 HOUR SILENT SUPERVISED ENTRY EXIT DELAY 2 W TAMPER Standard Detault Zone Types Pg 25 Booxounarumwe e Page 27 LOC PG DESCRIPTION DEFAULT DATA SIREN AND SYSTEM SUPERVISION Segment 1 Circle numbers to program c NOUS ON P Reserved Reserved Siren blast at arming Siren blast at exit delay expiration Siren blast at closing kissoff Siren sounds during a cross zone verification time Siren sounds for a tamper Siren blast one time for wireless arming two times for
3. The NX 4 can be programmed to perform a bell and or communicator test when 4 is entered while the system is in the disarmed state Loc 37 page 17 On Board Zone Disable The four zones on the NX 4 panel can be disabled in order to have a completely wireless alarm system Loc 37 page 17 Program Code The factory default for the Go To Program code is 9 7 1 3 when using a 4 digit code or if the 6 digit option is used the default is 9 7 1 3 0 0 The program code can also be used as an Arm Disarm code If used as an Arm Disarm code and open close reports are sent the user code will be 255 Loc 43 page 19 Quick Arm Feature The NX 4 has a one button Quick Arm feature which can be used to arm the system by pressing the Exit key or the Stay key If closing reports are sent the user code will be 98 Loc 23 page 16 Recent Closing If enabled the NX 4 will send a Recent Closing Report to the central station if an alarm occurs within 2 minutes after the panel is armed The user number that armed the system will also be sent Loc 23 page 16 The NX 4 has the ability to restart the exit delay for a quick exit without disarming the system by pressing the Exit key while the system is armed Loc 23 page 16 This mode will cause the keypads to turn off all LED s except the Power LED and not accept keypresses Loc 21 page 16 Siren Blast For Arming The NX 4 can be programmed to give
4. 5 6 7 8 R R Page 14 LOCATION 12 PROGRAMMING PHONE 3 20 segments numerical data Phone 3 is programmed in location 12 A 14 indicates the end of the phone number Delays of four seconds can be programmed at any point in the phone number by programming a 13 in the appropriate segment If tone dialing is desired program a 15 in the segment where tone dialing should begin If the entire number should be tone dialing program a 15 in the first segment Program an 11 for a and a 12 fora Caution A call waiting cancel on a non call waiting line will prevent successful connection to the central station LOCATION 13 ACCOUNT CODE FOR PHONE 3 6 segments numerical data The account code sent when Phone 3 is dialed is programmed in location 13 Program a 10 in the segment immediately after the last digit of the account code If the account code is 6 digits long program all 6 segments If location 6 is left unprogrammed account code 1 will be used when the Phone 3 is dialed LOCATION 14 COMMUNICATOR FORMAT FOR PHONE 3 1 segment numerical data Location 14 contains the communicator format used to transmit to the receiver connected to phone 3 Consult the instruction manual for your central station receiver to determine which format is compatible and select from the 15 formats listed on page 13 If you require a format other than those listed review the override options described in Location 18 t
5. Box Tamper feature is enabled in location 37 Segment 1 contains the tens digit of the Box Tamper Segment 2 contains the ones digit of the Box Tamper Segment 3 contains the tens digit of the Box Tamper Restore Segment 4 contains the ones digit of the Box Tamper Restore Page 22 LOCATION 68 AC FAIL AC FAIL RESTORE CODES 4 segments numerical data Location 68 contains the tens and ones digits for a 4 2 format that will be sent if AC Fail Reporting is enabled Segment 1 contains the tens digit of the AC Fail Reporting Segment 2 contains the ones digit of the AC Fail Reporting Segment 3 contains the tens digit of the AC Fail Restore Segment 4 contains the ones digit of the AC Fail Restore LOCATION 69 LOW BATTERY LOW BATTERY RESTORE CODES 4 segments numerical data Location 69 contains the tens and ones digits for a 4 2 format that will be sent if Low Battery Reporting is enabled Segment 1 contains the tens digit of the Low Battery Reporting Segment 2 contains the ones digit of the Low Battery Reporting Segment 3 contains the tens digit of the Low Battery Restore Segment 4 contains the ones digit of the Low Battery Restore LOCATION 70 AUX POWER OVER CURRENT AUX POWER OVER CURRENT RESTORE CODES 4 segments numerical data Location 70 contains the tens and ones digits for a 4 2 format that will be sent if Aux Power Over current Reporting is enabled Segment 1 contains the tens digit
6. 01 requirements Minimum System Requirements 1 control panel 2 keypads Remote arming shall NOT be enabled in SIA classified installations Off premise transmission must be in the SIA format The Abort window and Entry Delay must not exceed 1 minute CAUTION A call waiting cancel on a non call waiting line will prevent successful connection to the central station CP 01 Feature Feature Description Program Seg Opt Factory CP 01 Required Description as shown in manual Loc Default Setting Exit Time Exit 1 Delay 24 2 60 45 240 sec Exit 2 Delay 24 4 60 45 240 sec Progress Annuncation Disable Silent Keypad Option 93 2 All annunciators enabled Allowed for Silent Exit individual keypads may be disabled Exit Time Restart This feature is non programmable in the panel Enabled Auto Stay Arm on Unvacated Auto Bypass 23 1 3 Enabled Enabled Premises Exit Time and Progress This feature is non programmable in the panel Exit time and progress are always Enabled may be disabled for remote arming Annunciation Disable enabled for Remote Arm Entry Delay s Entry 1 Delay 24 1 30 30 240 sec NOTE Entry 2 Delay 24 3 30 30 240 sec Ped Abort Window Dialer Delay 40 8 30 Enabled window and for Non Fire Zones may be disabled by zone zone Entry Delay type must not exceed 1 Abort Window Time Dialer Delay 40 8 30 15 45 sec minute
7. A VALID USER CODE MAY BE REQUIRED AFTER 9 9 IF ENABLED IN LOCATION 41 PAGE 19 Page 9 PROGRAMMING THE NX 4 CONTROL ENTERING THE PROGRAM MODE To enter the Program Mode press 8 At this time the five function LEDs Stay Chime Exit Bypass amp Cancel will begin to flash Next enter the Go To Program Code FACTORY DEFAULT IS 9 7 1 3 If the Go To Program Code is valid the Service LED will flash and the five function LEDs will illuminate steady You are now in the Program Mode and ready to select the module to program SELECTING THE MODULE TO PROGRAM Since all modules connected to the NX 4 are programmed through the keypad the module you are programming should be the first entry To program the NX 4 Control Panel enter 0 The 0 is the module number of the control and the is the entry key Other module entry numbers can be found in their corresponding manuals PROGRAMMING A LOCATION Once the number of the module to be programmed has been entered the Armed LED will illuminate indicating it is waiting for a programming location to be entered Any location can be accessed by directly entering the desired programming location followed by the pound key If the location entered is a valid location the Armed LED will extinguish the Ready LED will illuminate and the binary data for the first segment of this location will be shown by the zone LED s While entering new data the Ready LED
8. CUSTOMIZING ZONE TYPES Configuration Groups NOTE Locations 110 149 are used to change the zone types configurations as listed in the table on page 25 These locations are considered advanced programming and should only be changed with a thorough understanding of the operation of each bit GROUP CHARACTERISTIC SELECTIONS Fire turn on if this is a fire zone 24 hour turn on for non fire 24 hour zones Reserved Follower turn on for burglary zones that are Instant during non entry times Delay 1 zone follows timer 1 entry and exit times Delay 2 zone follows timer 2 entry and exit times Interior turn on if zone should Automatically Bypass or Bypass for Stay Arming Local only turn on if this zone should not be reported will beep the keypad for alarm will sound the yelping siren for alarm will sound the temporal siren for alarm will chime will bypass will include in the group shunt is force armable is entry guard RESERVED On enables Double End Of Line Tamper zone Mainly used for tamper on wireless zones On enables Trouble Reporting zone Day zone and Fire zones On enables Cross Zoning On enables Dialer Delay zone See location 40 page 18 On enables swinger shutdown See location 38 page 18 7 On enables Restore reporting 8 On enables Listen In See location 40 page 18 LOCATION 110 GROUP 1 ALARM EVENT CODE 1 segment numerical data Location 110 contains the ev
9. POS AUX PWR Connect to the Positive terminal on the keypads expanders and other power devices This terminal is limited to 1 amp total current ZONE 4 Connect to one side of zone 4 loop Connect the other side to com Terminal Open or short causes alarm com common C terminal forzonesss4 O ZONES Connect to one side of zone 3 loop Connect the other side to com terminal Open or short causes alarm ZONE 2 Connect to one side of zone 2 loop Connect the other side to com terminal Open or short causes alarm com Common temmeorznesl amp 2 OOOO ZONE 1 Connectto one side of zone 1 loop Connect the other side to com terminal Open or short causes alarm E IMPORTANT 1 If separate power supplies are necessary to accommodate additional devices safety standards require that each power supply be prominently marked with adequate instructions for removing all power from the unit 2 Dispose of used batteries according to the manufacturer s instructions and or local government authorities 3 Installation personnel should thoroughly read and understand the installation instructions and the users manuals for the panel and all the accessories to be included with the system before attempting to install a security system Tv WARNING Replace only with Panasonic LC12V4BP or Yuasa NP4 12 battery Observe polarity when installing a new battery Installing the battery backwards may cause damage to the panel There is a risk of exp
10. Trouble and Trouble Restores Power Fail Low Battery Power Restore and Low Battery Restore Bell Cut Bell Cut Restore Test Reports Start and End programming Download complete Segment 2 Zone and Box Tamper and Tamper Restore Auxiliary Power Over current and Restore Wireless Sensor Missing and Restore Wireless Sensor Low Battery and Restore Expander Trouble and Restore Fail To Communicate Reserved Reserved 5 6 7 8 1 2 3 4 5 6 7 8 Page 13 LOCATION 6 PROGRAMMING PHONE 2 20 segments numerical data Phone 2 is programmed in location 6 A 14 indicates the end of the phone number Delays of four seconds can be programmed at any point in the phone number by programming a 13 in the appropriate segment If tone dialing is desired program a 15 in the segment where tone dialing should begin If the entire number should be tone dialing program a 15 in the first segment Program an 11 for a k and a 12 for a Caution A call waiting cancel on a non call waiting line will prevent successful connection to the central station LOCATION 7 ACCOUNT CODE FOR THE PHONE 2 6 segments of numerical data The account code sent when Phone 2 is dialed is programmed in location 7 Program a 10 in the segment immediately after the last digit of the account code If the account code is 6 digits long program all 6 segments If this location is left unprogrammed account code 1 will be used when the se
11. can only be viewed from the keypad and must be changed through downloading LOCATION 22 DOWNLOAD CALL BACK NUMBER 20 segments numerical data If a telephone number is programmed into this location and Require Callback is enabled in location 21 the control panel will hang up for approximately 36 seconds ensuring that the calling party has disconnected and then call back If tone dialing is desired program an 15 in the segment where tone dialing should begin If the entire number should be tone dialing program an A15 in the first segment Four second delays can be obtained anywhere in the sequence by programming a 13 in the appropriate delay location WARNING THE CALLBACK PHONE NUMBER SHOULD ALWAYS BE REVIEWED FOR ACCURACY BEFORE DISCONNECTING LOCATION 23 FEATURE AND REPORT SELECTIONS 3 segments feature selection data Location 23 is used to enable certain features that can be accessed or are visible to the user from the keypad of the system In addition certain communicator reports are enabled in location 23 This location contains 3 segments of 8 features each See Feature Definitions starting on page 3 Segment 1 1 On enables the Quick Arm feature 2 On enables the Re exit feature 3 On enables the Automatic Bypass feature Default is on 4 On enables the Silent Keypad Panic feature overrides the Audible Panic 5 On enables the Audible Keypad Panic feature Default is on 6 On enables the Keypad Aux
12. enabled the control panel can automatically bypass interior follower zones if an exit is not detected during the exit delay time Entry delay zones can also be made instant Loc 23 segments 1 amp 3 page 16 Auto Cancel Abort If enabled Cancel and or Abort features will be automatic means pressing the Cancel button is not required The Cancel Abort features in Locations 23 and 40 respectively must be enabled to permit this Auto feature to work For proper operation of these features Dialer Delay must be enabled in Characteristic Select of Locations 110 149 Zone Configuration Groups Loc 41 page 19 Auto Test This feature will cause the panel to call the central station to report a communicator test at a specified interval m Fe A Q wn o a D 3 a O ul E t a o 7 t i a N o Ke Auxiliary Outputs The NX 4 has two programmable outputs that can be used to activate relays LED s etc See the terminal description on page 37 and locations 45 50 pages 19 20 Auxiliary Power Over current The NX 4 will illuminate the Service LED on the keypad whenever too much current is drawn from any device powered by the system This condition can be reported to the central station Power down the system to clear Loc 37 page 17 Box Tamper The NX 4 has an input for a normally closed tamper switch see terminal drawing The Box Tamper can be programmed to report
13. for Non Fire Zones Abort Annunciation This feature is non programmable in the panel Flashing Cancel LED goes off when Enabled disarming Cancel Annunciation Cancel 23 3 6 Enabled Enabled Duress Feature Duress 44 Disabled Disabled Cross Zoning 2 Trips on Cross Zone 37 5 4 Disabled Required Keypad sounds on Cross Zone trip 39 5 Disabled Zone Type Characteristic 111 3 4 Disabled Programmable Cross Zoning Time Cross Zone Time 40 6 5 minutes Allowed Swinger Shutdown Swinger Shutdown Count 38 n a Enabled for 1 trip For all non fire zones shut down at 1 2 trips Swinger Shutdown Disable Swinger Shutdown Count 38 n a Enabled for 1 trip Allowed Fire Alarm Verification Fire Alarm Verification Time 40 9 Disabled Required depends on panel amp sensors Call Waiting Cancel Must be programmed as part of 0 n a n a Required depends on user phone line the phone number Default Changes from prior Recent Closing 23 3 7 Enabled versions Exit Error 23 3 8 Enabled Power Up Delay 40 3 60 sec SPECIFICATIONS OPERATING POWER AUXILIARY POWER w 25 VA Transformer w 40 or 50 VA Transformer LOOP RESISTANCE Standard Loop BUILT IN SIREN DRIVER LOOP RESPONSE OPERATING TEMPERATURE LED KEYPAD Current Draw Zones Normal w o Sounder Dimensions NX 148E LCD KEYPAD Current Draw w o Sounder Dimensions METAL ENCLOSURE DIMENSION SHIPPING WEIGHT 16 5 VAC 25 40 or 50 VA Transformer 12 VDC Regulated 500 mA 12 VDC Regulated
14. in 50mS 1 20th second increments from 0 12 seconds 0 follows zone 255 latched Segment 8 Dial delay in seconds 15 255 seconds Default is 30 seconds Segment 9 Fire Alarm Verification time in seconds 120 255 seconds Default is 0 no verification Segment 10 Listen In time in seconds 0 255 Default is 0 no Listen In time IMPORTANT NOTES 1 The Listen In feature cannot be enabled for UL Listed systems The Dynamic Battery Test feature cannot exceed four 4 hours The dial delay shall be set to O 2 For household systems the Fire Alarm Verification feature is NOT approved for use in California This feature shall not be programmed into the control unit Page 18 LOCATION 41 CODE REQUIREMENTS 1 segment feature data Segment 1 1 On enables the 6 digit code option If 6 digit option is enabled all arm disarm codes and the Go To Program Code must be 6 digits If this option is enabled the default user 1 code is 1 2 3 4 5 6 NOTE IF YOU ENABLE THIS OPTION VERIFY THAT THE GO TO PROGRAM CODE IS A SIX DIGIT CODE BEFORE EXITING PROGRAMMING 2 On requires code entry for 9 8 perform call back download and 9 9 answer incoming call for download functions Enable Auto Cancel Abort Refer to definitions beginning on page 3 Enable Walk Test Mode Refer to definitions beginning on page 3 8 Reserved LOCATION 42 GO TO PROGRAM CODE 6 segments numerical dat
15. installations 38 18 SWINGER SHUTDOWN COUNT 1 Page 28 LOC PG DESCRIPTION DEFAULT DATA lli Tl KEYPAD SOUNDER CONTROL Segment 1 Circle numbers to program Reserved Reserved Keypad sounds upon AC Power Failure Keypad sounds upon Low Battery Detection Keypad sounds during Cross Zone Trip Time Keypad sounds for Tamper Alarm Reserved Keypad sounds for expander trouble requi SYSTEM TIMERS Segment 1 Dynamic Battery Test duration 0 255 min Segment 2 AC Failure report delay 0 255 minutes Segment 3 Power Up Delay 0 60 seconds Segment 4 Siren Time 1 255 minutes Segment 5 Reserved Segment 6 Cross Zone Time 0 255 minutes Segment 27 Chime Time in 50 mS increments 0 255 Segment 8 Dialer delay 15 255 seconds Segment 9 Fire Alarm Verification Time 120 255 sec Segment 10 Listen In Time 0 255 seconds USER CODE REQUIREMENTS seaman 1 Circle numbers to program Enables six digit code option All arm disarm Go To Program codes require six digits Requires valid user code entry for 9 8 and 9 9 functions to work Enables Auto Cancel Abort Enables Walk Test mode Reserved GO TO PROGRAM CODE GO TO PROGRAM CODE AND AUTHORIZATION Segment 1 Circle numbers to program Reserved Enables Go To Program Code as an arm only code Enables Go To Program Code as an arm only after closing Enables Go To Program Code as a master arm disarm code can change
16. is selected for this segment press the key This will enter the data and automatically advance to the next segment of the location When you are in the last segment of a location and press the to enter the data you will exit that location This will now turn the Ready LED off and the Armed LED on As before you are now ready to enter another programming location LOADING FACTORY DEFAULTS To load the factory defaults enter the program mode using the procedure on page 10 then type 9 1 0 The keypad will beep 3 times indicating that the loading is in progress The loading takes about 6 seconds ENROLLING MODULES AND KEYPADS For supervision purposes the NX 4 has the ability to automatically find and store in its memory the presence of all keypads zone expanders wireless receivers and any other module connected to the data terminal This allows these modules to be supervised by the control panel To enroll the modules enter the Program Mode of the NX 4 control panel as described on page 10 When the Program Mode is exited the NX 4 control will automatically enroll the devices The enrolling process takes about 12 seconds during which time the Service LED will illuminate User codes will not be accepted during the enrolling process Once a module is enrolled if it is not detected by the control the Service LED will illuminate CONTROL PANEL PROGRAMMING LOCATIONS Note Various locations have been intentionally om
17. must be programmed in location 2 in addition to the entries in location 18 in order to create a special format If this location contains a 0 the built in communicator will be disabled and the NX 4 will function as a local only control LOCATION 3 DIAL ATTEMPTS BACKUP CONTROL FOR PHONE 1 2 segments numerical data Segment 1 Dial attempts Location 3 Segment 1 is used to enter the number of dial attempts 1 to 15 Attempts the communicator will make to Phone 1 before ending the notification process Factory default is 8 and the communicator will make eight 8 attempts to the first number Segment 2 Phone 1 Backup Control Programming a 0 in Segment 2 of this location will cause the NX 4 to make the designated number of attempts to Phone 2 before setting the Fail To Communicate condition and stop reporting Programming a 1 in this segment will cause the NX 4 to stop trying to communicate after the designated number of attempts have been made to Phone 1 If a 2 is programmed in this segment it will cause the NX 4 to make the dial attempts in increments of two The first two attempts will be made to Phone 1 the next two attempts to Phone 2 then repeating until the total number of attempts designated in Segment 1 is completed Page 12 FORMAT SELECTIONS DATA FORMAT DESCRIPTION Universal 442 Two digit event code 1800hz transmit 2300hz handshake double round parity 40pps EX 341 fast or 4 1 One digit event code 1
18. of the Aux Power Over current Reporting Segment 2 contains the ones digit of the Aux Power Over current Reporting Segment 3 contains the tens digit of the Aux Power Over current Restore Segment 4 contains the ones digit of the Aux Power Over current Restore LOCATION 71 BELL TAMPER BELL TAMPER RESTORE CODE 4 segments numerical data Location 71 contains the tens and ones digits for a 4 2 format that will be sent if siren supervision reporting is enabled Segment 1 contains the tens digit of the Bell Tamper Reporting Segment 2 contains the ones digit of the Bell Tamper Reporting Segment 3 contains the tens digit of the Bell Tamper Restore Segment 4 contains the ones digit of the Bell Tamper Restore LOCATION 74 EXPANDER TROUBLE EXPANDER TROUBLE RESTORE CODE 4 segments numerical data Location 74 contains the tens and ones digits for a 4 2 format that will be sent if Expander Trouble Reporting is enabled Segment 1 contains the tens digit of the Expander Trouble Reporting Segment 2 contains the ones digit of the Expander Trouble Reporting Segment 3 contains the tens digit of the Expander Trouble Restore Segment 4 contains the ones digit of the Expander Trouble Restore LOCATION 75 FAIL TO COMMUNICATE CODE 2 segments numerical data Location 75 contains the tens and ones digits for a 4 2 format that will be sent if the Fail To Communicate Reporting is enabled Segment 1 contains the tens dig
19. user codes Enables Go To Program Code as an arm disarm code Enables Go To Program Code to bypass zones Enables Go To Program Code opening and closing reports m O QUI ON P E puRSSCODE i CODE AUXILIARY OUTPUTS 1 amp 2 SPECIAL TIMING Segments Auxiliary output timed in minutes Auxiliary output to latch Auxiliary output to stop timing upon user code entry Auxiliary output to activate only between closing and opening time Auxiliary output to activate only between opening and closing time Invert auxiliary output 0 volts going to 12 volts when activated Reserved Reserved Page 29 DESCRIPTION DEFAULT DATA 19 AUXILIARY OUTPUT 1 EVENT amp TIME Segment 1 Program the event number for output 1 O Burglary alarm o Segment 2 Program the timing for output 1 here 10secods AUXILIARY OUTPUT 2 EVENT amp TIME Segment 1 Program the event number for output 2 1 Firealmrm Segment 2 Program the timing for output 2 here 10secods 20 AUTOTESTCONTROL CONTROL Segment 1 Program a 1 Bu e the interval is hours a O if in days Add a 2 to suppress the daily test or a 3 to suppress the hourly test Segment 2 Program the autotest interval from 1 255 days or hours Segment 3 Program the autotest report in 24 hour time format Segment 4 Program the autotest report time minutes after the hour OPENING TIME Segment 1 Program the hour of the opening
20. wireless disarming Note Must be disabled for SIA CP 01 installations Segment 2 Circle numbers to program ONAURWNE Segment 3 Circle numbers to program ONDUBRWNE Segment 4 Circle numbers to program c oU L ON Segment 5 Circle numbers to program ONU L ON Convert siren driver to voltage out Siren sounds for expander trouble required for U L Immediate Restore by Zone Dynamic battery test performed upon arming Battery missing test performed every 12 seconds Manual bell test performed during 4 test function Manual communicator test performed during 4 test function Box tamper enabled Box Tamper report enabled AC Fail report enabled Low Battery report enabled Auxiliary power over current report enabled Siren supervision report enabled Reserved Reserved Expander trouble report enabled Failure To Communicate report enabled Log Full report enabled Autotest report enabled Start and End Programming report enabled End Download report enabled Sensor Low Battery report enabled Sensor Missing report enabled Reserved Lost Clock service LED enable Zone Doubling enable Requires additional devices see page 7 Disable on board four zones Enables two trips on the same cross zone to activate the alarm Disables bypass reports for force armed zones Reserved Clock uses internal crystal Disable Temporal Siren on Fire Do NOT disable for UL
21. 1 AMP 300 Ohms Maximum 2 tone Temporal and Yelp 500mS 32 to 120 degrees F 130 mA max 55 mA 6 4 Wide 4 0 High 1 1 Deep 110 mA max 75 mA 6 4 Wide 5 3 High 1 0 Deep 9 25 Wide 8 25 High 3 50 Deep 9 Ibs 1420 N MAIN STREET GLADEWATER TEXAS 75647 Main 800 727 2339 Technical Support 800 727 2339 Outside the US 903 845 6941 Tech Support Fax 903 845 8409 Main Fax 903 845 6811 Sales amp Literature 800 547 2556 Web www caddx com www ge security com UL approved NX 4 INSTALLATION MANUAL for ANSI SIA NX4IM04 REV M AUG 2004 CP 01 2000
22. 1 feature FIRE 7 On enables the Keypad Aux 2 feature MEDICAL 8 On enables the Keypad Multiple Code Attempt Tamper feature Page 16 Segment 2 1 On enables the LED Extinguish feature 2 On enables the Require Code for Bypassing feature 3 On enables the Zone Bypassed Sounder Alert feature 4 On enables the AC Power Low Battery Sounder Alert feature Default is on 5 On enables Bypass toggle 6 On enables Silent Auto Arm 7 On enables the Automatic Instant feature 8 Reserved Segment 3 1 On enables Opening and Closing reports 2 On enables Zone Bypass reporting 3 On enables Zone Restore reporting 4 On enables Zone Trouble reporting 5 On enables Zone Tamper reporting 6 On enables the Cancel reporting Default is on 7 On enables the Recent Closing report Default is on 8 On enables the Exit Error report Default is on LOCATION 24 ENTRY EXIT TIMERS 4 segments numerical data Location 24 is used to program the Entry Exit times There are 2 separate Entry Exit times Segment 1 Entry time 1 This is the entry time that will be used when a delay 1 zone type initiates an entry delay Valid entries are 30 255 seconds Segment 2 Exit time 1 This is the exit time that will be used for all zones designated as delay 1 Valid entries are 45 255 seconds Segment 3 Entry time 2 This is the entry time that will be used when a delay 2 zone type initiates an entry delay Vali
23. 126 127 128 129 130 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 Page 32 APPENDIX 1 REPORTING FIXED CODES IN CONTACT ID AND SIA The table below list the event codes sent for the following reports if enabled when using CONTACT ID or SIA formats REPORT CONTACT ID SIA MANUAL TEST 601 RX AUTOTEST 602 RP OPEN user number 401 OP CLOSE user number 401 CL CANCEL user number 406 OC DOWNLOAD COMPLETE 412 RS START PROGRAM 627 LB END PROGRAM 628 LX RECENT CLOSE user number 401 CR EXIT ERROR user number 457 EE EVENT LOG FULL 605 JL FAIL TO COMMUNICATE 354 RT EXPANDER TROUBLE device number 333 ET EXPANDER RESTORE device number 333 ER SIREN TAMPER device number 321 YA SIREN RESTORE device number 321 YH AUX POWER OVER CURRENT device number 312 YP AUX POWER RESTORE device number 312 YQ LOW BATTERY device number 309 YT LOW BATTERY RESTORE device number 309 YR AC FAIL device number 301 AT AC RESTORE device number 301 AR BOX TAMPER device number 137 TA BOX TAMPER RESTORE device number 137 TR KEYPAD TAMPER 137 TA KEYPAD PANIC audible 120 PA KEYPAD PANIC silent 121 HA DURESS 121 HA KEYPAD AUXILIARY 1 110 FA KEYPAD AUXILIARY 2 100 MA RF SENSOR LOST zone number 381 T RF SENSOR RESTORE zone number 381 R SENSOR LOW BATTERY zone number 384 XT SENSOR BATTERY RESTORE zone number 384 XR ZONE TROUBLE zone number 380 T ZONE TROUBLE RESTORE zone number 3
24. 220FBI 13 and Ademco 685 2 11 12 and 13 For burglary installations cross zoned detectors shall overlap 100 percent in the area of coverage and similar coverage areas must be used For example interior protection is cross zoned with interior protection etc Expander trouble must activate the siren Loc 37 Segment 2 LED 2 For UL 1637 expander trouble must activate keypad sounder Loc 39 Segment 1 LED 8 The keypad used with wireless receivers and hardwire expansion must be able to display all zones in a system For Canadian installations the Class II transformer secure tab shall not be employed MINIMUM SYSTEM CONFIGURATIONS FOR UL INSTALLATIONS Residential Fire Residential Burglary Commercial Burglary The NetworX NX 4 panel is necessary to initiate Residential and Commercial installations At least one compatible keypad is needed for all applications At least one bell fixture is required for all applications except Grade C Central Station For Grade A Local the AD10 12 bell and Grade A bell housing shall be used Commercial UL applications require NX 003 C metal enclosure Supplied screws to be used A minimum of two 2 keypads are required for Home Health applications and each keypad must be set to a unique address The wireless devices are only UL listed for residential applications The DACT shall be enabled for all commercial burglary applications Page 40 SIA SYSTEM REQUIREMENTS ANSI SIA CP 01 To meet SIA CP
25. 4 14 14 14 1 12 PHONE 1 ACCOUNT CODE 10 10 10 10 10 10 AM ii KAMMER MUS CERE 3 12 PHONE 1 DIAL ATTEMPTS BACKUP CONTROL 13 IPHONE 1 SELECTING EVENTS TO REPORT TO PHONE 1 Segment 1 Circle Numbers To Program Segment 2 Circle Numbers To Program Alarms and Restores Tampers Short Circuit Sensor Lost Sensor Low Battery Power Trouble AC Failure or Low Battery Siren Test Reports Program Download amp Log Full Expander Trouble Failure To Communicate Reserved Reserved ONAUAWNE Ens PHONE 2 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 PHONE 2 DIAL ATTEMPTS BACKUP CONTROL 14 PHONE 2 SELECTING EVENTS TO REPORT TO PHONE 2 Segment 1 Circle Numbers To Program Segment 2 Circle Numbers To Program 1 Alarms and Restores 1 Tampers 2 Open Close 2 Short Circuit 3 Bypass 3 Sensor Lost 4 Zone Trouble 4 Sensor Low Battery 5 Power Trouble AC Failure or Low Battery 5 Expander Trouble 6 Siren 6 Failure To Communicate 4 Test Reports 7 Reserved Program Download amp Log Full 8 Reserved 12 15 PHONE 3 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 PHONE 3 ACCOUNT CODE 10 10 10 10 10 10 15 15 PHONE 3 DIAL ATTEMPTS BACKUP CONTROL 16 15 PHONE 3 SELECTING EVENTS TO REPORT TO PHONE 3 Segnen 1 Circle Numbers To Program Seg pen 2 Circle Numbers To P
26. 80 R ZONE TAMPER zone number 137 TA ZONE TAMPER RESTORE zone number 137 TR ZONE BYPASS zone number 570 B BYPASS RESTORE zone number 570 U THE NUMBER IN PARENTHESES FOLLOWING THE EVENT IS THE NUMBER THAT WILL BE REPORTED AS THE ZONE NUMBER IF THERE ARE NO PARENTHESES THE ZONE WILL BE 0 SEE PAGE 35 FOR THE DEVICE NUMBERS The character transmitted in this slot will be the first character from the event code of the zone that is bypassed or in trouble See locations 110 141 Page 33 APPENDIX 2 REPORTING ZONE CODES IN SIA OR CONTACT ID The NX 4 has the ability to report SIA level 1 transmissions to either or both phone numbers Each report in SIA consists of an Event Code and a Zone or User ID The Zone ID will be the zone number that is in alarm The event code will come from the chart below and be programmed in the configuration group event code Programmed Event Code SIA Code Description 0 HA Holdup Alarm 1 FA Fire Alarm 2 PA Panic alarm 3 BA Burglary Alarm 4 BA Burglary Alarm 5 BA Burglary Alarm 6 UA Untyped Alarm 7 BA Burglary Alarm 8 BA Burglary Alarm 9 UA Untyped Alarm 10 HA Holdup Alarm 11 MA Medical Alarm 12 PA Panic alarm 13 TA Tamper Alarm 14 RP Periodic Test 15 GA Gas Alarm 16 KA Heat Alarm 17 WA Water Alarm 18 QA Emergency Alarm 19 SA Sprinkler Alarm 20 ZA Freeze Alarm The NX 4 has the ability to report Ademco Contact ID transmissions Each report in Contact ID consists of an Event Code and a Zon
27. 900Hz transmit 1400Hz handshake double round parity 20pps 3 Jee Reeve 4 Pager gt dit event code DTME transmission _ s _ 3 4 oF 4 1 slow 1800hz transmit 2300h handshake double round party 20 pps hex capably e Jet slow 1800hz transmit 1400hz handshake double round party 20 ee hex capably e Jett 1800hz transmit 1400hz handshake double round party 40 p s hex capably 3 1 or 4 1 fast with 1800hz transmit 2300hz handshake single round w parity 40 p p s hex capability parity EG 3 1 or 4 1 fast with 1800hz transmit 1400hz handshake single round w parity 40 p p s hex capability parity 11 4 2express 2 digit event code DTMF transmission ELE S Two digit event code 1900hz transmit 1400hz handshake double round parity 20 p p s i13 Ademco Contact ID DTMF see pages 33 34 REPORTING EVENTS TO PHONE NUMBER 1 Location 4 is used to select which events are reported to Phone 1 If dual or split reporting is not desired location 4 should be used to select all events to Phone 1 If dual or split reporting is desired location 4 should be used to select only those events that should be reported to Phone 1 If no events should be reported to Phone 1 location 4 should be programmed as 0 disabled LOCATION 4 EVENTS REPORTED TO PHONE 1 2 segments feature selection data Segment 1 1 Alarms and Alarm Restores 2 Opening and Closings 3 Zone Bypass and Bypass Restores 4 Zone
28. CONNECTION REQUIREMENTS Except for telephone company provided ringers all connections to the telephone network shall be made through standard plugs and standard telephone company provided jacks or equivalent in such a manner as to allow for immediate disconnection of the terminal equipment Standard jacks shall be so arranged that if the plug connected thereto is withdrawn no interference to the operation of the equipment at the customers premises which remains connected to the telephone network shall occur by reason of such withdrawal INCIDENCE OF HARM Should terminal equipment or protective circuitry cause harm to the telephone network the telephone company shall where practical notify the customer that temporary discontinuance of service may be required However where prior notice is not practical the telephone company may temporarily discontinue service if such action is deemed reasonable in the circumstances In the case of such temporary discontinuance the telephone company shall promptly notify the customer who will be given the opportunity to correct the situation The customer also has the right to bring a complaint to the FCC if he feels the disconnection is not warranted CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES The telephone company may make changes in its communications facilities equipment operations or procedures where such action is reasonably required and proper in its business Should any such change rende
29. FAULTS LISTED IN THE ODD NUMBERED LOCATIONS BELOW REPRESENT THE THREE SEGMENTS OF EACH OF THOSE LOCATIONS USE THE THREE SEGMENT CHARTS FROM LOCATION 111 TO UNDERSTAND THESE DEFAULTS ur m wowixawEWenE z T ous 25 GROUP2 cHaRACTERISTIC SELECT zsa Loue rou saamevenrcooes Z Oo o ns s ooanamevenrcoos s T Fus 25 GROUPS ALARMEveNT cope s 119 GROUP 5 CHARACTERISTIC SELECT GROUP 6 ALARM EVENT CODE i awk 4 GROUP 6 CHARACTERISTIC SELECT GROUP 7 ALARM EVENT CODE EE NEMPE 5 GROUP 7 CHARACTERISTIC SELECT 2 08 GROUP 8 ALARM EVENT CODE SES Jd oz cu GROUP 8 CHARACTERISTIC SELECT 1 13 378 GROUP 9 ALARM EVENT CODE ill ce GROUP 9 CHARACTERISTIC SELECT 6 1245 5678 croup omarm evercoss 2 o 5 5 2 2 25 2 2 2 25 25 25 25 GROUP 10 CHARACTERISTIC SELECT 24 5 78 HE BENE 2 GROUP 12 ALARM EVENT CODE GROUP 12 CHARACTERISTIC SELECT 457 125 45678 GROUP 13 ALARM EVENT CODE GROUP 13 CHARACTERISTIC SELECT GROUP 14 ALARM EVENT CODE GROUP 14 CHARACTERISTIC SELECT 5 12456 5678 GROUP 15 ALARM EVENT CODE Dale GROUP 15 CHARACTERISTIC SELECT 457 1256 5678 GROUP 16 ALARM EVENT CODE WE od uw GROUP 16 CHARACTERISTIC SELECT 0 12456 5678 EREECHEN EELER GROUP 19 ALARM EVENT CODE plc 25 GROUP20 ALARM EvENTcODE O 7 Oooo o 25 GROUP 20 CHARACTERISTIC SELECT 6324525678 131 N ul 120 121 122 123 124 125
30. LOCATION 38 SWINGER SHUTDOWN COUNT Location 38 contains the number of trips on a zone before that zone is bypassed automatically Refer to the feature definitions beginning on page 3 Factory default is 1 LOCATION 39 KEYPAD SOUNDER CONTROL 1 segment feature selection data Segment 1 1 amp 2 Reserved 3 On if keypad sounds upon AC Power Failure 4 On if keypad sounds when a Low Battery is detected 5 On if keypad sounds during Cross Zone trip time 6 On if keypad sounds for zone and box tampers 7 Reserved 8 On if keypad sounds for expander trouble required for UL installations LOCATION 40 SYSTEM TIMERS 10 segments numerical data Location 40 contains the duration of various system timing functions Example If you desire the duration of the Dynamic Battery Test to be 30 minutes you should program 3 0 in segment 1 of this location The 3 0 is the number of minutes and the stores the data and moves to the next segment of this location Segment 1 Dynamic Battery Test duration in minutes 0 255 minutes Default is 0 no test Segment 2 AC Fail report delay in minutes 0 255 minutes Default is 5 minutes Segment 3 Power Up Delay in seconds 0 60 seconds 0 no power up delay Default is 60 seconds Segment 4 Siren Time in minutes 1 255 minutes Default is 8 minutes Segment 5 Reserved Segment 6 Cross Zone time in minutes 0 255 0 no cross zoning Default is 5 minutes Segment 7 Chime time
31. N 380ZL XN 340NS OL 3PZL XN 3911 XN 380i XN 3012313 340NS 33M P Wo9 FIHVd GVdA33 XHOMISN n n z 39IA3G 33H10 ONY m e SQVdA3 8 SI S39IA3 NOD Mir cen GaSIANaUNS UV SLNdNI INOZ TIY gt 38IM 1V101 XV xn 301A30 Jud xn Sod NOISNVdX3 ONY SOVdA3 amd xny WO2 WNOILLIGOY OL viva ipte pde SITOA SZ 6 IN Sdhiil NOSN3S S3SS3I0Ud zxnv 3univa4 Z ees wawo4zssvi TTT oL ON SI meest een 340NS LE MOUNT WOH UV SLINY TIV vu 0S2 OL G31INI1 LNIYYNI SI TWNIWYAL 340WS p s uadng S yawuossnval Qvo1MWHO VASZ V HLIM Vigor dida xnv 91 HO r Su3yVads HONG HLuva UM 0 HO SI NO WAOS 10 OF V HLIM VU 004 7TVNIWH31 YIAN N3MIS NI DI G339X3 LON Sr OL IVA OZH 83H13901 0200 123NNO2 Ru N3HM M ld XNY ION Od WAINIXYIN div SZ ONY SOd QVdA3x ov OL G3LINIT INIYYNI IONS S1VNIWH3L e HOH NMVYG 1N3aino XVN ASONYLS TY A IYIM 39nv9 EL WRWININ 3SN Sa dW Sc RS m ONO7 0 OL 9 QOY TV13W Sede AN er S Q31v2I03Q V HO 3dld u31VM 7H09 A8 Q3T10H1NOO SI YYOMLIN 0109 Q3l3hi3 V O1 G3l1 38 OV AZ 1VH1 319V1d3238 02131 OL mu OTNOHS NOLL23NNO2 QNnONS JHL AT3A1193343 MYOM OL VOL LOSNNOD WHO 009 4 NOILO31ONd ONINIHOM 04 10N OG TI SSVT9 1v 1060 9688 1300 kak q30Nno9 H1MV3 38 1S0W VADO UC NN LANHLGPGXN N3N3O3SNVMHL 800000S1 LS TANVd 1031N02 JHL Gish HS ONINIHOT 194 N3NHOJSNVSL uogejs jegue 2 g sapeo pue jun2es eur 3iseg YM JIBUUOD 2llod je07 y PLI9 aguas uueje 1e Bung eru Buymoyjoy y sapiAoJd osje y
32. NetworX NetworX Series NX 4 Control Panel Installation and Startup UL approved for ANSI SIA CP 01 2000 2004 GE Security All rights reserved Printed in the USA These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to be met during installation operation and maintenance If further information is desired or if particular problems arise that are not covered sufficiently for the purchaser s purpose the matter should be referred to GE Security Gladewater Texas USA This document contains proprietary information of GE Security USA and is furnished to its customer solely to assist that customer in the installation testing operations and or maintenance of the equipment described This document shall not be reproduced in whole or in part nor shall its contents be disclosed to any third party without the written approval of GE Security Please refer to the current GE Security product catalog for detailed warranty information Main 800 727 2339 Technical Support 800 727 2339 Outside the US 903 845 6941 Tech Support Fax 903 845 8409 Main Fax 903 845 681 1 Sales amp Literature 800 547 2556 www caddx com www ge interlogix com NetworX is a trademark of the GE Security companies NetworX NX 4 Control Communicator Installation Manual Page General DeSCriptiOnis uyo EET 2 Ordering Informations svc uice eger n usus mi ra xa en xg EEN 2 Board Install
33. Phone 3 If dual or split reporting is not desired location 16 should be left at the factory default of 0 If multi reporting or split reporting is desired and the split is based on the event type such as alarm open close etc then location 16 should be used to select only those events that should be reported to Phone 3 If no events should be reported to Phone 3 location 16 should be 0 LOCATION 16 EVENTS REPORTED TO PHONE 3 2 segments feature selection data Segment 1 1 Alarms and Alarm Restores 2 Opening and Closings 3 Zone Bypass and Bypass Restores 4 Zone Trouble and Trouble Restores 5 Power Fail Low Battery Power Restore and Low Battery Restore 6 Bell Cut Bell Cut Restore 7 Test Reports 8 Start and End programming Download complete Segment 2 one and Box Tamper and Tamper Restore uxiliary Power Over current and Restore ensor Missing and Restore ensor Low Battery and Restore Expander Trouble and Restore Fail To Communicate eserved eserved Z A S S R R Page 15 LOCATION 18 CUSTOM COMMUNICATOR FORMAT See locations 2 8 amp 14 Segment 1 1 On for 1800hz transmit Off for 1900hz 2 2 On for 2300hz handshake Off for 1400hz 3 On for cksum parity Off for double round parity 4 On for 2 digit event code Off for 1 digit event code 5 amp 6 Reserved 7 On for 20 p p s Off for 10 or 40 p p s 8 On for 10 p p s Off for 20 or 40 p p
34. a Location 42 contains the Go To Program Code This location contains either a 4 or 6 digit code If the 6 digit code option is enabled in Location 41 this code must contain six 6 digits If this option is not enabled in location 41 the last 2 segments digits will be ignored With the NX 4 disarmed the Go To Program Code can be used to enter the Program Mode LOCATION 43 GO TO PROGRAM CODE AND AUTHORIZATION 1 segment feature selection data The Go To Program Code can be used as a standard arm disarm code When using the code to arm or disarm the user ID is 255 This code may not be changed in the Run Mode Segment 1 1 Reserved 2 On enables Go To Program Code as an arm only code 3 On enables Go To Program Code as an arm only after closing 4 On enables Go To Program Code as a master arm disarm code can change user codes 5 On enables Go To Program Code as an arm disarm code 6 On enables Go To Program Code to bypass zones 7 On enables Go To Program Code opening and closing reports 8 Reserved LOCATION 44 DURESS CODE 6 segments numerical data Location 44 contains the Duress code This location contains either 4 or 6 digits If the 6 digit code option is enabled in Location 41 this code must contain six 6 digits If the 6 digit option is not enabled in location 41 the last 2 digits will be ignored LOCATION 46 AUXILIARY OUTPUT SPECIAL TIMING 2 segments feature selecti
35. a 2 is programmed in this segment it will cause the NX 4 to make the dial attempts in increments of two The first two attempts will be made to Phone 2 the next two attempts to Phone 1 then repeating until the total number of attempts designated in Segment 1 is completed REPORTING EVENTS TO PHONE NUMBER 2 Phone 2 can be used to back up Phone 1 or for a second receiver to multi report or split report events Location 10 is used to select which events are reported to Phone 2 If dual or split reporting is not desired location 10 should be left at the factory default of 0 If multi reporting or split reporting is desired location 10 should be used to select only those events that should be reported to Phone 2 If no events should be reported to Phone 2 location 10 should be 0 LOCATION 10 EVENTS REPORTED TO PHONE Z2 2 segments of feature selection data Segment 1 1 Alarms and Alarm Restores 2 Opening and Closings 3 Zone Bypass and Bypass Restores 4 Zone Trouble and Trouble Restores Power Fail Low Battery Power Restore and Low Battery Restore Bell Cut Bell Cut Restore Test Reports Start and End programming Download complete Segment 2 one and Box Tamper and Tamper Restore uxiliary Power Over current and Restore ensor Missing and Restore ensor Low Battery and Restore Expander Trouble and Restore Fail To Communicate eserved eserved 5 6 7 8 1 Z 2 A 3 S 4 S
36. a one second siren blast when the panel is armed at the end of the exit delay or when the central station receiver acknowledges the closing report It can also give one blast for wireless arming and two blasts for wireless disarming Loc 37 page 17 Siren Supervision The NX 4 has a Siren Supervision circuit that will constantly monitor the siren on the NX 4 and can be programmed to report if the wires are cut Loc 37 page 17 Silent Exit Option The exit delay can be silenced by pressing Exit before arming the control panel or when using the re exit feature Start End Programming and End Downloading A report can be sent when local programming is started and ended A report can also be sent when a download session ends Loc 37 page 17 Page 6 Swinger Shutdown This feature allows a zone s to be automatically bypassed after a specified number of alarms When a zone is tripped the alarm counter reflects 1 in memory If a new first alarm is detected in a different zone the counter remains at 1 If an alarm is detected on a previously tripped zone the count increments to 2 The counter will increment each time an alarm is detected on a zone with multiple trips Bypassing will occur on the zone that causes the count to equal the number programmed in location 38 the counter will reset to zero 0 and begin a new trip count where the next alarm will set the counter to 1 If immediate rest
37. am each code to be reported Loc 56 83 and 111 149 pages 22 25 Configuration Groups The NX 4 has 20 programmable configuration groups that determine how each zone will function and report The default configuration groups Zone Types are listed on page 25 Loc 111 149 pages 24 25 This feature requires two or more trips on a zone or zones programmed as cross zones within a specified time before reporting an alarm During the time between trips the NX 4 can be programmed to sound the keypad and or the siren The NX 4 can also be programmed to report an alarm after two or more trips on the same zone Loc 37 39 40 and 110 149 pages 17 18 24 25 Dual Split Multiple Reports The NX 4 can send communication reports to three different phone numbers for dual split or multiple reports selectable by event Loc 4 10 and 16 pages 13 15 Duress Code If a duress code is programmed the NX 4 will send a duress signal whenever the panel is armed or disarmed with this code If open close reports are sent the user code will be 254 Loc 44 page 19 Dynamic Battery Test The NX 4 can be programmed to perform a Dynamic Battery Test for a selected duration the first time the panel is armed or disarmed every day as well as by pressing 4 Test Function The NX 4 can also be programmed to perform a missing battery test every 12 seconds Loc 37 and 40 pages 17 and 18 Entry Guard This unique low level arming mode has been d
38. and or sound the siren and or the keypad These terminals can be enabled or disabled in programming Loc 37 and 39 page 17 Page 3 Built In Siren Driver The NX 4 has a built in 112db siren driver When desired this built in driver can be easily converted to a 1 amp voltage output through programming Loc 37 page 17 Bypass Toggle This feature will enable the end user to toggle turn on or off the bypass of an interior zone with the system armed by pressing the Bypass key Loc 23 page 16 Call Back When enabled the control will use the call back phone number to call the download computer before beginning a download Loc 21 page 16 If enabled the NX 4 will send a Cancel report if when the system is disarmed and the Cancel button is pressed within 5 minutes of an alarm Once the Cancel key is pressed the Cancel LED will illuminate until the central station acknowledges the Cancel report Dialer Delay must be enabled in the Characteristic Select of Loc 110 149 Loc 23 page 16 Code Required Options The NX 4 can be programmed to require a code for bypassing zones and or initiating a download using the 9 8 or 9 9 function Loc 23 and 41 pages 16 and 19 Communication Formats The NX 4 can report in multiple formats It is recommended that you use Contact ID or SIA formats if possible If you wish to report to a pager or in a 4 2 format to a central station you must progr
39. at disarming See loc 40 5 On if Battery Missing Test is performed every 12 seconds 6 On if Manual Bell Test performed during 4 test function 7 On if Manual Communicator Test performed during 4 test function 8 On if Box Tamper terminals on the control panel are enabled Segment 3 1 On if Box Tamper report enabled 2 On if AC Fail reporting enabled 3 On if Low Battery reporting enabled 4 On if Aux Power Over current report enabled 5 On if Siren Supervision report enabled 6 amp 7 Reserved 8 On if Expander Trouble reporting enabled Page 17 Segment 4 1 On if Fail To Communicate report enabled 2 On if Log Full report enabled 3 On if Autotest report enabled 4 On if Start End programming report enabled 5 On if End Download report enabled 6 On if Sensor Low Battery report enabled 7 On if Sensor Missing report enabled 8 Reserved Segment 5 1 On enable Lost Clock service light 2 On enables Zone Doubling Must have extra devices added to basic system to enable refer to page 7 NX 200 Zone Doubling Kit required On disables On Board 4 zones On will allow two trips on same cross zone to activate an alarm On will not allow zones that are force armed to report bypass Reserved 7 Use internal crystal for clock 8 Disable Temporal Siren on Fire NOTE For UL installations do NOT disable Refer to the feature definitions beginning on page 3 3 4 5 6
40. ation irre etr ERENNERT 2 Feature Definitioris eee reote nr ene ee ENER xxix x nd de EX SR Ex nn 3 Programming the LED KeypadS r rrrsrrrnrssrrsnsssa 8 Programming the NA 10 Types of Programming Data 10 Enrolling the Modules amp Kevpade mmm nnns 12 Communicator el EC 13 Reporting Events to Phone 1 2 amp 3 nennen 13 15 Zone Doublirig ne 18 Programming the Outputs r rrrrrsrrsrsrssrrsrsrsnsnrrsssssssa 19 20 Standard Zone Types Configurations 25 Programming Worksheets r rr emen meme 26 32 SIA and Contact ID Formats u S Qp eene enne 33 34 Expander Trouble Reporting Information 35 Wirirnig el Lee ln RTE 36 Terminal De scription y a ENEE EEN ENEE O A DI S A EID eee hd 37 Telephone Interface Information 39 Underwriters Laboratories Information 39 SIA ANSI CP 01 Reouirements 41 Specifications 5 x cu uay N eA ae Back Page GE Security 1 800 727 2339 GENERAL DESCRIPTION The NetworX NX 4 represents a new approach to security systems design Drawing on our experience in the world market as the largest exporter of USA manufactured controls we have developed the most flexible durable and user friendly control ever seen in our industry Featuring sophisticated software which allows up to 8 users to interface with 8 zones and a host of integrated fire access verification and input output modules all reported with the most comprehensive and fa
41. ce last autotest 1 Enter 9 5 program code The Service LED will flash 2 Enter 100 s digit 3 Enter 10 s digit 4 Enter 1 s digit 5 Press to save and exit 9 6 Set system date 1 Enter 9 6 master code The Service LED will flash 2 Enter day of week 1 Sun 3 Enter month 10 s digit 4 Enter month 1 s digit 5 Enter day 10 s digit 6 Enter day 1 s digit 7 Enter year 10 s digit 8 Enter year 1 s digit fee 7 Set system clock Enter 9 7 master code The Service LED will flash Enter hour 10 s digit Enter hour 1 s digit Enter minutes 10 s digit Enter minutes 1 s digit H bur Page 8 CHANGING USER CODES 1 Enter 5 master code The Ready LED will flash 2 Enter the 2 digit user number always 2 digits such as 03 for user 3 The Ready LED will illuminate steady 3 Enter the new user code designated for that individual The Ready LED will flash indicating that the code was accepted If it rejects the code the sounder will beep 3 times Note for NX1300 Series LED Keypad The zone lights will illuminate specifying the first digit of the user code Lights 1 8 on code is blank lights 1 8 off 0 lights 1 and 8 9 Use the up and down scroll keys to view the next digit or enter a new 4 or 6 digit user code While using the scroll keys you can change any digit by entering a new digit This will advance you to the next dig
42. code or 1 2 3 4 5 6 for a 6 digit code The factory default for the Go To Program code is 9 7 1 3 for a 4 digit code or 9 7 1 3 0 0 for a 6 digit code 9 3 Set keypad options 1 Enter 9 3 program code The Service LED will flash 2 LEDs 1 8 can now be toggled on off to enable disable the following functions 3 After enabling disabling the desired functions press un KEPADFEATREENAMED Enable Keypress Silence option silences the pulsing keypad sounder for 5 seconds when a key is pressed 5 Enable Armed Status Suppression will not allow the keypad to display faulted or bypassed zones when the system is armed Enable Panic Fire Medical Beeptone will sound a short beep to verify that the keypress was accepted Suppresses the Service LED will not allow the Service LED to illuminate for any reason If there is a system trouble pressing 2 will still show the service menu NOTE For UL installations the Service LED shall not be suppressed po RESERVED This LED should always be OFF 9 4 Set keypad number 1 Enter 9 4 program code The Service LED and the Instant LED will flash 2 Enter the keypad number 1 8 3 Press x The Instant LED will illuminate steady and the Service LED will remain flashing 4 Enter 1 The keypad will automatically exit this mode at this time 9 5 Set elapsed increments sin
43. cond phone number is dialed LOCATION 8 COMMUNICATOR FORMAT FOR PHONE 2 1 segment numerical data Location 8 contains the communicator format used to transmit to the receiver connected to Phone 2 Consult the instruction manual for your central station receiver to determine which format is compatible and select from the 15 formats listed on page 13 If you require a format other than those listed review the override options described in Location 18 to build the appropriate format A 15 must be programmed in location 8 in addition to the entries in location 18 in order to create a special format If this location contains a 0 format 1 will be used when Phone 2 is dialed LOCATION 9 DIAL ATTEMPTS BACKUP CONTROL FOR PHONE 2 2 segments numerical data Segment 1 Dial attempts Segment 1 of Location 9 is used to enter the number of dial attempts 1 to 15 attempts the communicator will make to Phone 2 before ending the notification process Factory default is 8 and the communicator will make the same number of attempts as those programmed in location 3 Segment 2 Phone 2 Backup Control Programming a 0 in Segment 2 of this location will cause the NX 4 to make the designated number of attempts to Phone 1 before setting the Fail To Communicate condition and stop reporting Programming a 1 in this segment will cause the NX 4 to stop trying to communicate after the designated number of attempts have been made to Phone 2 If
44. d entries are 30 255 seconds Segment 4 Exit time 2 This is the exit time that will be used for all zones designated as delay 2 Valid entries are 45 255 seconds LOCATION 25 ZONES 1 8 ZONE TYPES 8 segments numerical data Location 25 contains the Zone Type Configuration Group for zones 1 8 Segment 1 is for zone 1 and Segment 8 is for zone 8 Default zone types are found in Table 2 1 on page 25 Refer also to the programming worksheets To customize a Zone Configuration Group refer to Locations 110 149 starting on page 24 LOCATION 37 SIREN AND SYSTEM SUPERVISION 5 segments feature selection data Location 37 is used to enable various system feature and reporting options Refer to the feature definitions Segment 1 1 amp 2 Reserved 3 On if siren blast at arming 4 On if siren blast at exit expiration 5 On if siren blast at closing kissoff 6 On if siren sounds during a Cross Zone verification time 7 On if siren sounds for a Zone or Box Tamper 8 On if siren blasts 1 time for wireless arming 2 times for wireless disarming Note Must be disabled for SIA CP 01 installations Segment 2 1 On if siren driver should be a voltage output Off if on board siren driver enabled 2 On if siren sounds for expander trouble required for UL installations 3 On for zones to immediately restore Off for zones to restore only when siren is off 4 On if Dynamic Battery Test performed at arming Off if performed
45. e ID The zone ID is the zone that created the alarm The event code will come from the chart below and be programmed in the configuration group event code Programmed Event Code Contact ID Code Description 0 122 Silent Panic 1 110 Fire Alarm 2 120 Panic alarm 3 130 Burglary Alarm 4 131 Perimeter Alarm 5 132 Interior Alarm 6 133 24 Hour Burglary 7 134 Entry Alarm 8 135 Day Night Alarm 9 150 Non Burglary 24 Hour 10 121 Duress Alarm 11 100 Medical Alarm 12 123 Audible Panic Alarm 13 137 Tamper Alarm 14 602 Periodic Test 15 151 Gas Detected 16 158 High Temp 17 154 Water Leakage 18 140 General Alarm 19 140 General Alarm 20 159 Low Temp Page 34 APPENDIX 3 EXPANDER NUMBERS FOR REPORTING EXPANDER TROUBLE The tables below list the device numbers that will be reported for trouble conditions Device Device reported NX 4 Control Panel See pages 33 34 for possible report codes NX 534E Two Way Listen In 64 NX 540E Operator NX 582E AES Interface NX 591E Cellemetry Interface KEYPADS Keypad 1 2 3 4 5 6 7 8 REMOTE POWER SUPPLY NX 320E OUTPUT MODULE NX 508E Address amp Dip Switch Setting Address amp Dip Switch Setting 28 Switch 1 2 83 on 29 All switches off WIRELESS RECEIVER NX 448E reported KEYPAD MAXIMUM WIRE RUN Note These numbers are for one keypad at the end of the wire When connecting more than one keypad to the end of the wire a higher gauge wi
46. ent code sent for a Contact ID or SIA report The desired event code should be chosen from the list on page 34 The zone ID will be that zone that is in alarm If 4 2 format is being used the number programmed in this location will be sent as the tens digit When using 4 2 the digit in location 110 should be from 1 15 The zone ID for 4 2 formats will be the ones digit of the zone that is in alarm LOCATION 111 GROUP 1 CHARACTERISTIC SELECT 3 segments feature selection data Use Table 1 1 Group Characteristic Selection above to program this location Page 24 LOCATIONS 112 THRU 149 contain the remaining 19 Customized Zone Group information The even numbered locations reflect the Group Alarm Event Code and the odd numbered locations designate the Group Characteristics Locations 112 and 113 correspond to Group 2 Locations 148 and 149 correspond to Group 20 Use the description found in Location 110 for programming the Alarm Event Codes and use Table 1 1 shown on page 24 to select the Group Characteristics Refer also to the Programming Worksheets Table 2 1 STANDARD ZONE TYPES Default Configurations Zones can be programmed to be one of twenty different zone types configurations Zone types 17 20 can be used for wireless or hardwired zones using European double EOL configuration The default zone types are listed below If none of the following zone types meet your needs these configurations can be customized by programming locat
47. erating the system for at least 24 hours battery standby in the normal condition and followed by not less than 4 minutes of alarm as required by code APPROVAL Listed as household fire alarm control unit for use with separately listed compatible initiating and indicating devices The control unit can generate the three pulse temporal code pattern fire alarm signal for total evacuation as required per NFPA 72 1996 Edition Page 39 UNDERWRITERS LABORATORIES INFORMATION The NetworX NX 4 holds the following listings from Underwriters Laboratories US and Canada Household Burglary UL1023 ORD C1023 1974 Household Fire UL985 CAN ULC S545 M89 Local Grade A Mercantile Police Station Connect with Basic Line Security UL609 requires NX 003 C enclosure CAN ULC S303 M91 Grade B amp C Central Station Burglar Alarm Unit UL1610 CAN ULC S304 M88 Home Health Care Signaling UL1637 When installing an NX 4 in compliance with Underwriters Laboratories the following instructions must be observed Initiating and indicating devices must be rated at 11 5 to 12 4 V DC residential 12 0 V DC commercial Force Arming and Auto Arming shall not be enabled For residential fire applications the indicating devices shall be a Wheelock 34T 12 or equivalent The Listen In feature shall not be enabled The Siren Bell Test shall be enabled The auxiliary outputs controlling the audible device require a minimum cutoff time of 15 minutes f
48. eveloped to reduce the most common source of false alarms When armed with the Instant light on the opening of any zones designated as Entry Guard zone will initiate the keypad sounder and start the entry delay before creating an alarm All other zones will function as normal This arming mode will encourage system owners to use their system more frequently when the premise is occupied Loc 111 149 pages 24 25 NOTE For UL installations this feature shall be disabled Page 4 If enabled the NX 4 will send an Exit Error Report if an entry exit zone is faulted at the instant the exit delay expires This report will be sent along with the user number that armed the system if the panel is not disarmed before the entry delay expires The alarm report will also be sent Even if this feature is not enabled the siren will sound if any entry exit zone is faulted at the instant the exit delay expires Loc 23 page 16 Expander Trouble The NX 4 will report expander trouble to the central station if enabled This condition will illuminate the Service LED on the keypad even if not reported NOTE The keypads are considered expanders The number of the expansion devices reported can be found on page 35 Loc 37 page 17 Fail to Communicate The NX 4 will illuminate the Service LED if a report fails to reach the central station If enabled when the next report is successfully communicated a Fail to Communicate code will be reported Loc 37
49. eypad The LED s for Zone 2 and Zone 7 will become illuminated indicating 66 is in that location 2 64 66 See this example on page 10 Once the data is programmed press the key to enter the data and advance to the next segment of that location After the last segment of a location is programmed pressing the key will exit that location turn the Ready LED off and the Armed LED on As before you are now ready to enter another programming location If an attempt is made to program a number too large for a particular segment the keypad sounder will emit a triple beep indicating an error and remain in that segment awaiting a valid entry On the LCD keypad the number in the location will be displayed For locations with a maximum of 15 the hexidecimal equivalent will be displayed in parenthesis Example 11 B or 14 E Page 10 PROGRAMMING EXAMPLE FIGURE 1 Numerical Data BEE ree Fi o 5 o a 9 10 11 12 Zone 1 LED 1 Zone 2 LED 2 Data 9 j Data Zone 7 LED 64 Data 66 Zone 4 LED 8 To change data ina segment enter the data followed by k Pressing will exit a location without changing the data in the current segment 13 14 15 16 17 18 19 20 21 22 23 24 Enters the previous Returns to the location just Advances to the next programming location programmed programming location PROGRAMMING EXAMPLE FIGURE 2 Feature Select
50. g with the date and time of the event These events can later be viewed through downloading or on the LCD keypad All reportable events report to the log Keypad Activated Panics The NX 4 has three keypad activated panics that will send reports to the central station Auxiliary 1 Fire Auxiliary 2 Medical and Keypad Panic Auxiliary 1 will activate the steady Fire siren Auxiliary 2 will sound the keypad and the Keypad Panic can be programmed to be silent or audible sound siren Loc 23 page 16 Keypad Sounder Control The NX 4 can be programmed to sound the keypad sounder for certain events Loc 39 page 18 Keypad Tamper If enabled the NX 4 will disable the keypad for 60 seconds and communicate a tamper signal to the central station if 30 keypresses are entered without producing a valid code Loc 23 page 16 This feature will extinguish all LED s on the keypad except the Power LED after 60 seconds without a keypress Pressing any numeric key will illuminate all LED s Loc 23 page 16 Page 5 Local Programming Lockout This feature will disable programming of all locations or specified locations from the keypad Loc 21 page 16 Log Full Report A report can be sent to the central station when the event log is full Loc 37 page 17 Lost Clock Service Light The NX 4 can be programmed to illuminate the Service LED when the internal clock has an invalid time due to power loss Loc 37 page 17 Manual Test
51. ion Data Location 23 Segment 1 1 Quick Arm 2 Re Exit 3 Auto Bypass 4 Silent Keypad Panic 5 Audible Keypad Panic 6 Keypad Auxiliary 1 7 Keypad Auxiliary 2 8 Multi Keypad Tamper Press the key on the numeric keypad that corresponds to the feature you wish to enable disable When an LED is on a feature is enabled when off the feature is disabled For example With the 1 5 amp 7 LEDs on Quick Arm Audible Keypad Panic and Keypad Auxiliary 2 are enabled Page 11 FEATURE SELECTION DATA Feature selection data will display the current condition on or off of eight features associated with the programming location and segment selected Pressing a button on the touchpad 1 thru 8 that corresponds to the feature number within a segment will toggle on off that feature Pressing any numeric key between 1 and 8 for selection of a feature will make the corresponding LED illuminate feature ON Press the number again and the LED will extinguish feature OFF You will see that numerous features can be selected from within one segment For instance if all eight features of a segment are desired pressing 1 2 3 4 5 6 7 8 will turn on LED s 1 thru 8 as you press the keys indicating that those features are enabled LCD Keypad Users Note The numbers of the enabled features will be displayed However the features not enabled will display a hyphen After the desired setting of features
52. ions 110 149 DATA DESCRIPTION OF STANDARD ZONE TYPES 1 DAY ZONE Instant when system is armed trouble zone when system is disarmed 24 HOUR AUDIBLE Creates an instant yelping siren alarm regardless of the armed state of the panel ENTRY EXIT DELAY 1 A trip will start entry delay 1 The lack of a trip during exit delay will enable the Automatic Bypass or Instant mode if so programmed FOLLOWER WITH AUTO BYPASS DISABLED This zone will be instant when the system is armed and no entry or exit delays are being timed It is delayed during entry and exit delay times This zone will not automatically bypass even if enabled in Segment 1 of Location 23 INTERIOR FOLLOWER WITH AUTO BYPASS ENABLED This zone will be instant when the system is armed and no entry or exit delay is being timed It is delayed during entry and exit delay times This zone will automatically bypass if enabled in Segment 1 of Location 23 INSTANT This zone creates an instant alarm whenever it is tripped and the Armed LED is on 7g 24 HOUR SILENT Creates an instant silent alarm regardless of the armed state of the control panel It will not display on the keypad FIRE This zone will light the Fire LED and sound the temporal siren each time the zone is shorted It will also rapidly flash the Fire LED indicating a trouble if the zone is open ENTRY EXIT DELAY 2 A trip will start entry delay 2 The lack of a trip during exit delay will enable the Automatic B
53. is the ones digit of the user who closed If it is required to report Recent Closings and Exit Errors for more than 9 users Contact ID or SIA format must be used Page 23 LOCATION 81 START PROGRAM AND END PROGRAM CODES 4 segments numerical data Location 81 contains the tens and ones digits for a 4 2 format that will be sent if Start End Programming Reporting is enabled Segment 1 contains the tens digit of the Start Program Reporting Segment 2 contains the ones digit of the Start Program Reporting Segment 3 contains the tens digit of the End Program Reporting Segment 4 contains the ones digit of the End Program Reporting LOCATION 82 END DOWNLOAD CODE 4 segments numerical data Location 82 contains the tens and ones digits for a 4 2 format that will be sent if End Downloading Reporting is enabled Segment 1 and 2 are reserved Segment 3 contains the tens digit of the End Download Reporting Segment 4 contains the ones digit of the End Download Reporting Note A start download report will be sent to the internal event log LOCATION 83 CANCEL CODE 1 segment numerical data Location 83 contains the tens digit for a 4 2 format that will be sent if Cancel Reporting is enabled Segment 1 contains the tens digit for the Cancel Communicator Reporting The ones digit is the ones digit of the user who canceled If it is required to report Cancels for more than 9 users Contact ID or SIA format must be used
54. it 4 If another user code needs to be programmed return to step 2 5 Press while the Ready LED is flashing to exit the User Code Programming Mode ASSIGNING AUTHORITY LEVEL 1 Enter 6 master code The Ready LED will flash 2 Enter 2 digit user number always 2 digit such as 03 for user 3 The Ready LED will illuminate steady and the Instant LED will flash 3 Refer to this chart for the description of each LED Turn the LED on for the features that you desire 3 famon 3 arm only ater Close Window A Master armvdisarm can program other codes s In LS Lenger amp Allowed to bypass zones see cation 23 Ka If this LED is on LEDs 1 7 will use the chart to the f this LED is off LEDs 1 7 use the chart to the right 4 Enter k k This step returns you back to step 2 above At this point you may enter another user number to assign attributes for You may continue this procedure until you have assigned authority levels to all user numbers or you may press key to exit the Assigning Authority Level Program m s p 9 8 Pressing 9 8 while the system is disarmed will cause the control to do a callback for a download NOTE A VALID USER CODE MAY BE REQUIRED AFTER 9 8 IF ENABLED IN LOCATION 41 PAGE 19 9 9 Pressing 9 9 while the system is disarmed will cause the control panel to seize the phone line for a download NOTE
55. it segment 2 contains the ones digit LOCATION 76 LOG FULL CODE 2 segments numerical data Location 76 contains the tens and ones digits for a 4 2 format if the Log Full Reporting is enabled Segment 1 contains the tens digit segment 2 contains the ones digit LOCATION 77 OPENING CODE 1 segment numerical data Location 77 contains the tens digit of a 4 2 format if the Opening Reporting is enabled The ones digit is the ones digit of the user number that did the opening If the user is greater than 9 the numbers will begin repeating LOCATION 78 CLOSING CODE 1 segment numerical data Location 78 contains the tens digit of a 4 2 format if the Closing Reporting is enabled The ones digit is the ones digit of the user number that did the closing If the user is greater than 9 the numbers will begin repeating LOCATION 79 AUTOTEST CODE 2 segments numerical data Location 79 contains the tens and ones digits for a 4 2 format that will be sent if the Autotest or Manual Test is enabled Segment 1 contains the tens digit segment 2 contains the ones digit LOCATION 80 RECENT CLOSING AND EXIT ERROR CODE 2 segments numerical data Location 80 contains the tens digit for a 4 2 format that will be sent if Recent Closing and or Exit Error Reporting is enabled Segment 1 contains the tens digit for the Recent Closing Reporting Segment 2 contains the digit for the Exit Error Reporting The ones digit
56. itted Any attempts to access these locations will be followed by an error Deep LOCATION 0 PHONE NUMBER 1 20 segments numerical data The first telephone number is programmed in location 0 A 14 indicates the end of the phone number Delays of four seconds can be programmed at any point in the phone number by programming a 13 in the appropriate segment If tone dialing is desired program a 15 in the segment where tone dialing should begin If the entire number should be tone dialing program a 15 in the first segment Program an 11 for a and a 12 for a Caution A call waiting cancel on a non call waiting line will prevent successful connection to the central station LOCATION 1 ACCOUNT CODE FOR THE PHONE 1 6 segments numerical data The account code sent when Phone 1 is dialed is programmed in location 1 Program a 10 in the segment immediately after the last digit of the account code If the account code is 6 digits long program all 6 segments LOCATION 2 COMMUNICATOR FORMAT FOR PHONE 1 1 segment numerical data Location 2 contains the communicator format used to transmit to the receiver connected to Phone 1 Consult the instructions for your central station receiver to determine which format is compatible Select a format from the list on the following page If you require a format other than those listed review the override options described in location 18 to build the appropriate format A 15
57. key will exit this programming level and go to the Select a Module To Program level If no additional modules are to be programmed pressing the Exit key again will exit the program mode If there is a module to be programmed it may be selected by entering its address followed by the key see Selecting the Module To Program above The procedure for programming these devices is the same as for the control panel except the locations will be for the module selected PROGRAMMING DATA Programming data is always one of two types One type of data is numerical and can take on values from 0 15 or 0 255 depending on the location s segment The other type of data is a feature selection type Feature selection data is used to turn features on or off Use the following procedures when working with these two data types NUMERICAL DATA Numerical data is programmed by entering a number from 0 255 on the numeric keys of the system keypad To view the data in a location a binary process is used With this process the LED s for zones 1 through 8 are utilized and the numeric equivalents of their illuminated LED s are added together to determine the data in a programming location The numeric equivalents of these LED s are as follows Zone 1 LED 1 Zone 2 LED 2 Zone 3 LED 4 Zone 4 LED 8 Zone 5 LED 16 Zone 6 LED 32 Zone 7 LED 64 Zone 8 LED 128 Example If the numerical data to be programmed in a location is 66 press 6 6 on the k
58. larm 35 Irak 30 open eriod 31 Closed Period 32 fisem _ _ 33 line ewe sa Ground Stare 35 rail To Communicate 36 used OOOO Ca 49 a Ca as 44 4s 46 J Tamper Alarm 5 Yelping Siren Burglary 6 Temporal Siren Fire 7 Any Siren 8 Any Bypass 9 AC Fail 10 Low Battery Panic Keypad Zone Short Circuit Over current EC 16 d Autotest 17 Any Open 7 8 37 Alarm Memory Fire k nil Notes When Event 48 is programmed it is possible to program a user code s authorization to select which output s a particular code will activate When LED 8 is on for an authorization then LEDs 1 2 correspond to that code activating outputs 1 amp 2 respectively See programming the LED keypads on page 8 Events 49 amp 50 require NX 408E NX 416E or NX 448E wireless receivers to operate V If set to follow condition these events will be 1 second LOCATION 51 AUTOTEST CONTROL 4 segments numerical data Segment 1 Program a 1 if the interval is to be in hours Program a 0 if in days Add a 2 to suppress the daily test or a 3 to suppress the hourly test if any report has been sent Segment 2 Program the Autotest interval from 1 255 hours days Segment 3 Program the Autotest report hour in 24 hour format if the interval is in hours this segment is ignored Segment 4 Program the Autotest report time number
59. losion if the battery is replaced with an incorrect type NOTE Electrical codes will vary depending upon the country and city where the system is installed It is the installer s responsibility to ensure that the electrical installation is safe and conforms to all applicable codes laws or regulations Only qualified persons should connect this device to the mains supply Page 37 Notices Applies to products which have the CE mark attached DECLARATION OF CONFORMITY Manufacturer s Name Caddx Controls Manufacturer s Address 1420 N Main Street EU Representative Product Identification Product Model Brand Gladewater TX 75647 Interlogix Europe NetworX NX 4 CADDX R amp TTE Directive See EMC and LVD tests below EMC Directive EN50081 1 EN50130 4 EN55022 EN60950 EN61000 3 2 EN61000 3 3 LVD Directive EN 60950 1999 4 3rd edition Means of Conformity We declare under our sole responsibility that this product is in conformity with Directive 1999 5 EC R amp TTE Directive 73 23 EEC LVD and Directive 89 336 EEC EMC and based on test results using non harmonized standards in accordance with the Directives mentioned Additional Tests This equipment has been tested and found to comply with the following standards which are no longer required for compliance Page 38 Network Compatibility Declaration We declare under our sole responsibility that this product is designed to
60. nd or Low Battery conditions to the central station It can also be programmed to sound the keypad immediately upon detection of the condition The AC failure report warning can be delayed Loc 37 and 39 page 17 18 AC Power Low Battery Sounder Alert If enabled the NX 4 will beep the keypad sounder upon arming or disarming if the AC power is missing or a low battery has been detected Loc 23 page 16 Arm Disarm Codes The NX 4 can have 8 four digit codes OR 8 six digit codes to arm disarm the control All codes must have the same number of digits The factory default for User 1 is 1 2 3 4 when using a 4 digit code or 1 2 3 4 5 6 for a 6 digit code This code can then be used to enter the new arm disarm codes Loc 41 page 19 Automatic Arming If programmed the NX 4 will Auto Arm at the time specified in location 53 At that time the keypad will beep for 50 seconds before the panel arms The arming process will be stopped if a code is entered on the keypad The NX 4 will attempt to arm after every 45 minutes of inactivity until the next opening time loc 52 or until the system is armed The 45 minute timer will be extended when there is activity in the building causing the Ready LED to turn off and on If closing reports are sent the user code will be 97 Loc 23 and 52 55 pages 16 and 21 NOTE For UL installations this feature shall be disabled Automatic Bypass Instant Arming When
61. ns the event code for a zone Bypass for a 4 2 format The digit programmed in this location will be sent as the tens digit The zone ID will always be reported as the ones digit of the zone number i e 3 for zone 3 LOCATION 58 TAMPER CODE 1 segment numerical data Location 58 contains the event code for a zone Tamper for a 4 2 format The digit programmed in this location will be sent as the tens digit The zone ID will always be reported as the zone number i e 3 for zone 3 LOCATION 59 TROUBLE CODE 1 segment numerical data Location 59 contains the event code for a zone Trouble for a 4 2 format The digit programmed in this location will be sent as the tens digit The zone ID will always be reported as the zone number i e 3 for zone 3 LOCATION 60 SENSOR LOW BATTERY CODE 1 segment numerical data Location 60 contains the event code for a zone Sensor Low Battery for a 4 2 format The digit programmed in this location will be sent as the tens digit The zone ID will always be reported as the zone number i e 3 for zone 3 LOCATION 61 SENSOR MISSING CODE 1 segment numerical data Location 61 contains the event code for a zone Sensor Missing for a 4 2 format The digit programmed in this location will be sent as the tens digit The zone ID will always be reported as the zone number i e 3 for zone 3 LOCATION 62 DURESS CODE 2 segments numerical data Location 62 contains the tens and ones digi
62. o build the appropriate format A 15 must be programmed in location 14 in addition to the entries in location 18 in order to create a special format If this location contains a 0 format 1 will be used when Phone 3 is dialed LOCATION 15 DIAL ATTEMPTS BACKUP CONTROL FOR PHONE 3 2 segments numerical data Segment 1 Dial Attempts Segment 1 of Location 15 is used to enter the number of dial attempts 1 to 15 attempts the communicator will try to Phone 3 before ending the notification process Factory default is 8 and the communicator will make the same number of attempts as those programmed in location 3 Segment 2 Phone 3 Backup Control Programming a 0 in Segment 2 of this location will cause the NX 4 to make the designated number of attempts to Phone 2 before setting the Fail To Communicate condition and stop reporting Programming a 1 in this segment will cause the NX 4 to stop trying to communicate after the designated number of attempts have been made to Phone 3 If a 2 is programmed in this segment it will cause the NX 4 to make the dial attempts in increments of two The first two attempts will be made to Phone 3 the next two attempts to Phone 2 then repeating until the total number of attempts designated in Segment 1 is completed REPORTING EVENTS TO PHONE NUMBER 3 Phone 3 can be used for a third receiver to multi report or split report events Location 16 is used to select which events are reported to
63. of minutes after the hour Page 20 LOCATION 52 OPENING TIME 2 segments numerical data Location 52 contains the time in 24 hour format the NX 4 enables codes designated as arm only after closing This time is only valid on those days programmed in location 54 NOTE Opening time must be earlier than closing time for Auto Arm Aux Outputs or Code Authorization to function properly Segment 1 Program the hour of the opening time Segment 2 Program the minutes after the hour of the opening time LOCATION 53 CLOSING TIME AUTOMATIC ARMING TIME 2 segments numerical data Location 53 contains the time in 24 hour format the NX 4 disables the disarm capability for codes designated as arm only after closing This is also the time the Automatic Arming sequence will begin if enabled in location 55 NOTE Opening time must be earlier than closing time for Auto Arm Auxiliary Outputs or Code Authorization to function properly Segment 1 Program the hour of the closing auto arm time Segment 2 Program the minutes after the hour of the closing auto arm time LOCATION 54 DAYS OF THE WEEK SYSTEM IS OPEN 1 segment feature selection data Location 54 selects which days of the week system is open On these days arm only after close window codes will be able to arm and disarm during open window NOTE If system is not programmed to be opened and is programmed to Auto Arm Location 55 the NX 4 will try to arm every 45 minutes f
64. on data Location 46 contains special timing feature activation for the two auxiliary outputs Segment 1 corresponds to output 1 Segment 2 corresponds to output 2 Segments 1 2 1 On if output should be timed in minutes Off if timed in seconds 2 On if output should latch Off if output should be timed 3 On if output should stop timing upon code entry Off if the output should continue to time upon code entry 4 On if output should only activate between the closing and opening time in loc 52 and 53 5 On if output should only activate between the opening and closing time in loc 52 and 53 6 On if output should be inverted 0 volts going to 12 volts when activated 7 Reserved 8 Reserved LOCATION 47 AUXILIARY OUTPUT 1 EVENT AND TIME 2 segments numerical data Segment 1 Use the chart on page 20 to select the event that will activate Auxiliary Output 1 Segment 2 Program the timing from 0 255 minutes or seconds depending on data programmed in Segment 1 Location 46 Programming a 0 makes the output follow the event LOCATION 48 AUXILIARY OUTPUT 2 EVENT AND TIME 2 segments numerical data Segment 1 Use the chart on page 20 to select the event that will activate Auxiliary Output 2 Segment 2 Program the timing from 0 255 minutes or seconds depending on data programmed in Segment 2 Location 46 Programming a 0 makes the output follow the event Page 19 AUXILIARY OUTPUT EVENT SELECTION Burglary A
65. or commercial burglary 4 minutes for residential applications or 30 minutes for commercial burglary for Canada For residential fire installations the Dynamic Battery Test time cannot exceed four 4 hours Ringback shall be enabled on UL commercial burglary installations On commercial burglary installations the fire initiating circuits shall not be connected The Entry Guard feature shall be disabled Group Bypassing shall be disabled Delay before dial seizure shall be set to O Total current draw from aux power connections at terminal positions POS AUX PWR and SMOKE PWR must not exceed 400 mA Remote Downloading shall not be used on UL listed systems For residential burglary applications the maximum entry and exit delay times shall be 45 and 60 seconds respectively The exit delay time shall not exceed 60 seconds for commercial burglar alarm applications The keyswitch option shall not be used The telephone line monitor shall be enabled The Telephone Line Cut delay shall not exceed 90 seconds 24 hour communicator test transmission is required For 24 hours of standby power using a 7 0 AH battery limit auxiliary power load to 140 mA For 24 hours of standby power using a 17 2 AH battery limit auxiliary power load to 400 mA The silent keypad option shall not be enabled UL has only verified compatibility with the following listed DACRs and formats Sure Gard SG MLR2 DG 2 9 10 12 13 14 Silent Knight 9000 2 12 FBI CP
66. or the duration of the closed period On days not selected here arm only after close window codes will not disarm See locations 52 and 53 for the opening and closing times for the open days Segment 1 1 Open on Sunday 2 Open on Monday 3 Open on Tuesday 4 Open on Wednesday 5 Open on Thursday 6 Open on Friday 7 Open on Saturday 8 Reserved LOCATION 55 DAYS OF THE WEEK FOR AUTO ARMING 1 segment feature selection data Location 55 selects which days the system will auto arm If a zone is faulted when the panel tries to auto arm the zone will be bypassed Segment 1 1 Auto Arming on Sunday 2 Auto Arming on Monday 3 Auto Arming on Tuesday 4 Auto Arming on Wednesday 5 Auto Arming on Thursday 6 Auto Arming on Friday 7 Auto Arming on Saturday 8 Reserved Page 21 COMMUNICATOR CODES FOR SLOW FORMATS ONLY LOCATIONS 56 83 ARE ONLY USED WHEN REPORTING EVENTS TO A PAGER OR USING A SLOW FORMAT SUCH AS 4 2 WHEN USING CONTACT ID OR SIA THERE IS NO NEED TO PROGRAM THESE LOCATIONS LOCATION 56 RESTORE CODE 1 segment numerical data Location 56 contains the event code for any zone Restore for a 4 2 format The digit programmed in this location will be sent as the tens digit in place of the alarm event code The zone ID will always be reported as the ones digit of the zone number i e 3 for zone 3 LOCATION 57 BYPASS CODE 1 segment numerical data Location 57 contai
67. ore is enabled in location 37 the alarms and restores if enabled will be sent as they occur If immediate restore is not enabled a second or subsequent alarm will not be sent until the siren times out Factory default is 1 Loc 37 and 38 page 17 Temporal Siren Disable If disabled the Fire Siren will be steady and Fire Voltage Out will be the same as Burglary continuous Otherwise the Fire Siren will be temporal Loc 37 page 18 NOTE For UL installations do NOT disable Two Call Answering Machine Defeat If enabled to defeat an answering machine two telephone calls must be made to the premises On the first call let the phone ring one or two times The control panel will detect these rings and start a 45 second timer during which the control panel will answer the next call on the first ring This is not recommended for commercial applications Loc 21 page 16 Walk Test Mode Chime If enabled entering Chime followed by a user code will allow a walk through zone test where all zones become silent and local non reporting Each time a zone is faulted the zone light on the LED keypad will illuminate and the chime will sound The number of the faulted zone s will be displayed on the LCD keypad It will also be entered into alarm memory and the internal log To exit at any time during this mode enter a user code Otherwise the Walk Test Mode will automatically exit after 15 minutes Loc 41 page 19 Wireles
68. page 17 Fire Alarm Verification When enabled the NX 4 will verify a Fire alarm by requiring more than one trip on a smoke detector within a specified time before creating an alarm NOTE For household systems the Fire Alarm Verification feature is NOT approved for use in California This feature shall not be programmed into the control unit Loc 40 page 18 Force Arming When enabled the NX 4 can be Force Armed with zones violated Under this condition if a force armable zone is not secure the Ready LED will flash At the end of the exit delay these zones will become bypassed If these zones become secured any time during the arming cycle they will be unbypassed and active in the system If Bypass Report is enabled the force arming zones can be programmed to report bypass when they are Force Armed default or to not report bypass even if Bypass Report is enabled Loc 37 and 111 149 pages 17 amp 24 25 NOTE For UL installations this feature shall be disabled Group Bypass A designated group of zones can be programmed to bypass by pressing Bypass 0 Bypass Bypass prior to arming Loc 111 149 pages 24 25 NOTE For UL installations this feature shall be disabled Immediate Restore By Zone The NX 4 can be programmed to send alarm and restore reports as soon as they occur or wait until the siren time has expired Loc 37 page 17 Internal Event Log Up to 185 events can be stored in memory alon
69. r the customers terminal equipment incompatible with the telephone company facilities the customer shall be given adequate notice to make modifications to maintain uninterrupted service GENERAL The FCC prohibits customer provided terminal equipment be connected to party lines IMPORTANCE OF THE RINGER EQUIVALENCE NUMBER The Ringer Equivalence Number REN of this device is 0 1B This number is a representation of the electrical load that it applies to your telephone line MALFUNCTION OF THE EQUIPMENT In the event that the device should fail to operate properly the customer shall disconnect the equipment from the telephone line to determine if it is the customer s equipment that is not functioning properly If the problem is with the device the customer shall discontinue use until it is repaired EQUIPMENT INFORMATION MANUFACTURER OF CONNECTING EQUIPMENT CADDX CONTROLS INC FCC REGISTRATION NUMBER GCQUSA 33408 AL E RINGER EQUIVALENCE 0 1 B CALIFORNIA STATE FIRE MARSHAL LISTING LISTING No 7167 1249 105 CATEGORY Control Unit Household DESIGN Model NX 4 combination household fire and burglary alarm control units RATING 120 VAC primary 16 5 VAC secondary 12 VDC standby INSTALLATION In accordance with listee s printed installation instructions NFPA 72 applicable codes amp ordinances and in a manner acceptable to the authority having jurisdiction The system must have the secondary power supply capable of op
70. re will be required WHEN CONNECTED TO NX 4 WHEN CONNECTED TO NX 320E Page 35 borod shee ee MOLSIS3H 103 HLIM LOVLNOD Q035012 ATIVIWHON L ON LOVLNOD N3dO ATIVW3ON L 103 WEE SNId 3S3H1 OL HOLIMS Q03S012 ATWWHON V 193NNOO E NOLLWIO1 NI Q318VN3 SI Madiivi XO8 3l WIRING DIAGRAM YOLSISSY TO3 HLIM 19V1NOO 038019 yee ATIVWYON Z ONY o YOLSISSY T03 19V1NO2 N3dO HLM LOVINOD S ATIW3ONZ qaso12 ATTVINON Gag moo KC res yee asn suajs s 1n 104 TOS 3NOZ 319NIS 7VNIWH31 TVNIWH3I Tyna ew WOO ANY 3NOZANY WO2ANV 3NOZANY 3NOZ 3313 V Sv q3sn NOILVYNSISNOD 3NOZ d318nod MOILSIS3N T03 HLIM LOVINOO 8 3NOZ N3dO ATIVW3ON Toa Tana 703 Wit NEE 940 LO A NYS Nea 7TVNIWN31 NSL TL TVNIWH3L 1 S3N02 WODANY 3NOZANV WO2ANV 3NOZANY Toa nanoa 318VSn LON SI 8 3NOZ H9IH FHL 3NOZ J la V SV G3SN SI 3NOZ 1318000 V dl ss 703 KO SYOLSISSY E 8 6 S3NOZ 304 SI NOLSISM 969 3H1 P L S3NOZ 304 SI YOISISTY WE IHL NOLVHR9IHNOO 3Noz a318noa NOLLVENDISNOD TOI 318noa Nv3do3n3 12V1NOO ET OC WE wee IVNWW831 NIWH3L TNW WOOANV 3NOZANY WODANV TNL 3NOZ ANY NOLSIS3H 40103130 10393 TO a EE pert Luvd asn Saa S19V1NO2 391430 33H10 L quayeainb3 Ly WV ONY SQVdA3M 8 XVIN 10 yp0Z 1S3 pon M Av 138 EA NOMWWOO OL 39GI XN 38051 XN NOISIA3dhs V 3PC L XN 391 LXN 380 LXN TO3Qgaisn Tn IVNIW331 39Pl XN 38PZI X
71. rogram Open Close Alarms and Restores Tampers Bypass Short Circuit Sensor Lost Zone Trouble Sensor Low Battery Power Trouble AC Failure or Low Battery Siren Test Reports Program Download amp Log Full Expander Trouble Failure To Communicate Reserved Reserved D N ONU L ON P co N ON UI T QON P Page Page 26 Loc pG DESCRIPTION DEFAULT DATA 18 16 FORMAT OVERRIDE seg pent 1 Circle Numbers To Program Segment 2 Circle Numbers To Program On 1800hz transmit Off 1900hz On pager format no handshake required On 2300hz handshake Off 1400hz _ On 1400 2300 handshake On cksum parity Off double round parity Reserved On 2 digit event code Off 1 digit code Reserved Reserved On Contact ID Reserved On SIA On 20 p p s Off 10 or 40 p p s On Contact ID or 4 3 On 10 p p s Off 20 or 40 p p s On DTMF Segments 3 amp 4 RESERVED 19 DOWNLOAD ACCESS CODE 8 4 8 0 0 0 0 0 21 GE CONTROL Segment 1 Circle Numbers To Program 1 Circle Numbers To Program Enables two call answering machine defeat 2 Reserved Requires callback before downloading Shutdown control panel Lock out local programming Lock out communicator programming Lock out download section Enables callback at autotest interval 22 16 CALLBACK PHONE NUMBER 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 23 16 FEATURE SELECTION Segment 1 Segment 2 Segment
72. s Segment 2 1 On for pager format no handshake required 2 On for 1400 2300 handshake 3 amp 4 Reserved 5 On for Contact ID 6 On for SIA 7 On for Contact ID or 443 8 On for DTMF Segment 3 amp 4 Reserved LOCATION 19 DOWNLOAD ACCESS CODE 8 segments numerical data Location 19 contains the eight digit access code the NX 4 must receive from the downloading software before the panel will permit downloading to occur The factory default code is 84800000 LOCATION 20 NUMBER OF RINGS TO ANSWER 1 segment numerical data Location 20 contains the number of rings to answer for a download Enter a number from 0 disabled to 15 Factory default is 8 and the NX 4 will answer on 8 rings LOCATION 21 DOWNLOAD CONTROL 1 segment feature selection data Location 21 contains the feature selections for the controlling of download sessions The following features can be enabled or disabled using this location See Feature Definitions starting on page 3 Segment 1 1 On enables two call answering machine defeat 2 Reserved 3 Onrequires call back before download session 4 Shutdown 5 gt Onlocks all local programming 6 gt Onlocks programming of all locations associated with the communicator 7 gt Onlocks out download section If On locations 19 22 cannot be viewed from the keypad can only be viewed from the keypad when Off 8 On enables call back at auto test interval gt These selections
73. s Sensor Missing Low Battery The NX 4 will send a report to the central station when a wireless sensor has detected a low battery or has not reported to the receiver The Service LED will illuminate when either condition exists Loc 37 page 17 Zone Bypassed Sounder Alert If this feature is enabled the NX 4 will beep the keypad sounder upon arming if a zone is bypassed Loc 23 page 16 Zone Doubling Requires additional devices Zone doubling can only be enabled when at least one other device is added to the basic system consisting of the main control panel and one keypad Additional devices can include wireless receivers extra keypads etc If enabled this feature allows you to use the four zones on the panel as eight normally closed zones When this feature is used European double E O L configuration cannot be used THIS FEATURE DOES NOT INCREASE THE TOTAL NUMBER OF AVAILABLE ZONES BEYOND 8 If one of the eight zones must be a fire zone it must be one of Zones 1 4 The corresponding upper zone will become unavailable For example if Zone 4 is a fire zone then Zone 8 will not be available Loc 37 page 17 Page 7 PROGRAMMING THE LED KEYPADS This section describes how to program the address of each keypad as well as the options that are available The address of the keypad is important because this is how the panel supervises the keypads The factory default for the Master code is 1 2 3 4 when using a 4 digit
74. s an instant alarm whenever it is tripped and the Armed LED is on This zone will bypass when the Group Bypass command is entered at the keypad ENTRY EXIT DELAY 1 WITH TAMPER ENABLED A trip will start entry delay 1 The lack of a trip during exit delay will 17 enable the Automatic Bypass or Instant mode if so programmed This configuration group can be used to enable tamper on a wireless transmitter INTERIOR FOLLOWER WITH TAMPER AND AUTO BYPASS ENABLED This zone will be instant when the system is armed and no entry or exit delay is being timed It is delayed during entry and exit delay times This zone will automatically bypass if enabled in Segment 1 of Location 23 This configuration group can be used to enable tamper on a wireless transmitter INSTANT WITH TAMPER ENABLED This zone creates an instant alarm whenever it is tripped and the Armed LED is on This configuration group can be used to enable tamper on a wireless transmitter ENTRY EXIT DELAY 2 WITH TAMPER ENABLED A trip will start entry delay 2 The lack of a trip during exit delay will enable the Automatic Bypass or Instant mode if so programmed This configuration group can be used to enable tamper on a wireless transmitter Page 25 PROGRAMMING WORKSHEETS Factory defaults for segments are in bold italics text Some locations are reserved and have been intentionally omitted PIEINEECCOONM NEIN NO IR E dul 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 1
75. sT communicator cope KK 80 23 RECENT CLOSINGANDexITERROR Si 24 START PROGRAMMING 7 END PROGRAMMING LI oooo 92 24 ENDDOWNORD 7 0909 5 zmwmcowmuwcwoRcog e T CUSTOMIZING ZONE TYPES GROUPS These locations are considered advanced programming and should only be changed with a thorough understanding of the operation of each bit These locations are used to design or customize zones when the Standard Zones Types in Table 2 1 on page 25 do not fit your needs GROUP 1 ALARM EVENT CODE DI pm 111 24 GROUP 1 CHARACTERISTIC SELECT Segment 1 Circle numbers to program Fire enable for fire zone Delay 1 zone enable to follow Timer 1 Entry Exit 24 Hour enable for non fire 24 hour times zone Delay 2 zone enable to follow Timer 1 Entry Exit Reserved times Follower enable for burg zones that are Interior Enable for auto bypass or stay arming instant during non entry times Local Only enable if zone is not to be reported Segment 2 Circle numbers to program AW Ne o uo On 1 Keypad audible on alarm Bypassable 2 Yelping siren on alarm 3 Temporal siren on alarm 4 Chime Segment 3 Circle numbers to program RESERVED Double End of Line Tamper zone Group Shunt Force Armable Entry Guard eo o0 Ul Dialer Delay zone Swinger zone Restore reporting Listen In Trouble zone Day zone Cross Zone WNe ONAN Page 31 THE DE
76. st SIA and Contact ID formats The NetworX design allows a fully loaded system to be housed in one single metal enclosure establishing for the first time a logical solution and design response to modular systems A maximum of 8 keypads and 1 other module excluding hardwire can be added to expand the capabilities of the NX 4 unit For warranty information please refer to the current GE Security Product Catalog ORDERING INFORMATION PART DESCRIPTION PART DESCRIPTION NX 4 KIT NX 4 Control NX 108E LED Keypad amp NX 108E 8 Zone LED Keypad 16 5V 40VA Transformer NX 4 NX 4 Control Only NX 116E 16 Zone LED Keypad NX 200 Zone Doubling Kit Includes 100 3 74k NX 124E 24 Zone LED Keypad and 100 6 98k resistors NX 320E Smart Power Supply and Buss Extender NX 148E Alphanumeric LCD Keypad NX 408E 8 Zone Wireless Expansion Module NX 1192E 192 Zone LCD Keypad UL LISTED PART 60 904 NX 416E 16 Zone Wireless Expansion Module NX 1208E 8 Zone LED Keypad UL LISTED PART 60 904 NX 448E 48 Zone Wireless Expansion Module NX 1248E 48 Zone LCD Keypad UL LISTED PART 60 904 NX 508E Eight Output Module NX 1308E 8 Zone LED Door Design Keypad NX 534E Two Way Listen In Module NX 1316E 16 Zone LED Door Design Keypad NX 540E Operator II Telephone Interface Module NX 1324E 24 Zone LED Door Design Keypad NX 591E Cellemetry Interface NX 1448E 48 Zone Fixed Language Icon Keypad These products have not been tested and approved b
77. time Segment 2 Program the minutes after the hour of the opening time CLOSING TIME AUTO ARMING TIME Segment 1 Program the hour of the closing time auto arming time Segment 2 Program the minutes after hour of closing auto arming time DAYS OF THE WEEK SYSTEM IS OPEN 1 Sunday Thursday Monday Friday Tuesday Saturday Wednesday Reserved 21 DAYS OF THE WEEK AUTO ARMING WILL OCCUR Sunday Thursday Monday Friday Tuesday Saturday Wednesday Reserved LOC 56 83 COMMUNICATOR CODES FOR SLOW SPEED FORMATS ONLY DESCRIPTION DEFAULT DATA 22 RESTORE COMMUNICATOR CODE 14 _ 22 BYPASS COMMUNICATOR CODE 0 22 TAMPER COMMUNICATOR CODE 0 _ 22 TROUBLE COMMUNICATOR CODE Ln 22 SENSOR MISSING COMMUNICATOR CODE EXE iE E e zwmumyi EE Page 30 oc e mmm mam mm BN 22 AUXILIARY 2 PE ete pa or Ls 2 aao MULTE CODE BURY TAPER S 67 22 BOXTAWPER BOXTAMPERRESTORE OOOO es 23 ACPAL ACRESTORE 6 75 LOWBATIERY lOWBATTERYRESTORE 02 90 70 25 POWER SHORT POWER SHORT RESTORE 009 0 IL 7 25 BELL TAMPER BELL TAMPER RESTORE 99 98 74 23 EXPANDER TROUBLE EXPANDER TROUBLE RESTORE 0 0 0 0 75 FAILURE TO CommuNTATE T L eo 76 23 ocru communicator cope oo 77 z wewmccoorcowwUMCHDORCOD 34 7s 25 CLOSING COMMUNICATOR CODE Jo o oe o o 79 auToTe
78. ts that will be sent for a 4 2 format if the Duress code is enabled in location 44 Segment 1 contains the tens digit segment 2 contains the ones digit LOCATION 63 KEYPAD AUXILIARY 1 CODE 2 segments numerical data Location 63 contains the tens and ones digits that will be sent for a 4 2 format if the keypad Auxiliary 1 FIRE is enabled in location 23 Segment 1 contains the tens digit segment 2 contains the ones digit LOCATION 64 KEYPAD AUXILIARY 2 CODE 2 segments numerical data Location 64 contains the tens and ones digits that will be sent for a 4 2 format if the keypad Auxiliary 2 MEDICAL is enabled in location 23 Segment 1 contains the tens digit segment 2 contains the ones digit LOCATION 65 KEYPAD PANIC CODE 2 segments numerical data Location 65 contains the tens and ones digits that will be sent for a 4 2 format if the keypad Panic is enabled in location 23 Segment 1 contains the tens digit segment 2 contains the ones digit LOCATION 66 KEYPAD MULTIPLE CODE ENTRY TAMPER CODE 2 segments numerical data Location 66 contains the tens and ones digits that will be sent for a 4 2 format if the keypad Multiple Code Entry Tamper is enabled in location 23 Segment 1 contains the tens digit segment 2 contains the ones digit LOCATION 67 BOX TAMPER BOX TAMPER RESTORE CODES 4 segments numerical data Location 67 contains the tens and ones digits that will be sent for a 4 2 format if the
79. un sup ensoj2us 2 E00 XN eui ui uorounfuoo uj 3 AJ s uueje Je Bung Jenuepisey y epeJo9 sepiAoud yun si 69220 VW un ed yosew Uayeg uonel5ossy uon2ajo4d 84I4 IeuoneN 661 24 VdJN ISNV oi Bujp4o22e pajjejsul uauM 3 AJ S uueje au jepuepisas sepiAoud jun Siu f SVX31 331v Maav19 FAN XYOMLAN SJOJONPUOD Jaujo JJe tuoJj 1eujeq e nonpuoo uou Jo Buigni e nonpuoo uou Aq JO uui JO unuululu e pajejedas aq Jsnw el qe5 eu puoKaq Buipusyxe SJO onpuoo JINDJIO Wee as pajuur ieod pue SSEID d SSe an pue 02 Vd3N ISNV 9D0O e2132e 3 jeuoneN Aq peyiuued ajqeo mnsqns J0 d 19 10 8E1O 19 Buisn Catia aq en syinoJi uueje asy pajuui je od pue Sse Z SSEID SY SNOLLVTIVISNI T dvi Olanv ZtrdMg sen Jo d8rAZIHOWE ASQNVIS NI Vu09 Sean 7I3NVd 1O81NO5 SunoH r 1SV311V ABQNVIS A9N3983W3 303 ALIDVdV9 Au311v8 ONIDIANAS OL YOId SNM 3NOHd3131 3H1 193NNOOSIG SAVMTV 420HS 7V21412313 40 NSH 1N3A3Hd OL SNINSVM KINO Nouvi3do LINDID YIJdOYd 403 SIG31SIH1 d Lss 586 Wd4N HLIM 39NVG3O22V NI G3TIV1SNI 3801 SI 1N3WdInO3 YIJAWNN A9N3933 3 39r10d V O1 Q31LINSNY1 38 LON TIVHS TWNOIS WV TI NV7193n8 JHL NOILOIGSIunr SNIAVH ALIMOHLNY 1V201 3H1 3O TVAONddV 3H1 HLIM AINO G311IW33d 38 TTVHS NOLLWLS WULN3D MO Su31uvnoQv3H WHY Tv 3314 v OL IVNSIS WHV1V 3313 IHL 30 NOISSINSNVM L Page 36 TERMINAL DESCRIPTIONS mi house Telephone Ring s m Telephone Ring Red
80. will begin flashing to indicate a data change in process The flashing will continue until the new data is stored by pressing the x key Upon pressing the key the keypad will advance to the next segment and display its data This procedure is repeated until the last segment is reached Pressing the key will exit from this location and the Armed LED will illuminate again waiting for a new programming location to be entered If the desired location is the next sequential location press the POLICE key If the previous location is desired press the FIRE key If the same location is desired press the MEDIC key To review the data in a location repeat the above procedure pressing the key without any numeric data entry Each time the key is pressed the programming data of the next segment will be displayed for review EXITING A LOCATION After the last segment of a location is programmed pressing k will save the data exit that location turn the Ready LED off and the Armed LED on To exit before the last segment press As before you are now ready to enter another programming location If an attempt is made to program an invalid entry for a particular segment the keypad sounder will emit a triple error beep beep beep beep and remain in that segment awaiting a valid entry EXITING THE PROGRAM MODE When all the desired changes in programming have been made it is time to exit the program mode Pressing the Exit
81. work with the networks in the countries marked with a check v and may have interworking problems with the countries that are not checked Due to the inherent differences in the individual PSTNs certain software settings may need to be adjusted on a country to country basis If it is desired to use this equipment on a network other than the one on which it was originally installed you should contact your equipment supplier Austria _ Liechtenstein v Belgium v Luxembourg v Denmark v Netherlands v Finland v Norway v France v Poland v Germany v Portugal v Greece Y Spain Iceland v Sweden Ireland Y Switzerland Y Italy v United Kingdom Telecom Approval Notice This equipment has been approved in accordance with the Council Decision 98 482 EC for pan European single terminal connection to the public switched telephone network PSTN However due to the differences between the individual PSTNs provided in different countries the approval does not of itself give an unconditional assurance of successful operation on every PSTN network termination point In the event of problems you should contact your equipment supplier in the first instance Electrical Requirements This device automatically adjusts to voltages within the range of 230 V 50 60 Hz Fuse Type T 200mA 250 VAC LOCAL TELEPHONE COMPANY INTERFACE INFORMATION TELEPHONE
82. y Underwriters Laboratories Inc These wireless devices are only UL listed for residential applications IMPORTANT NOTES 1 The maximum number of zones available is 8 regardless of devices added Information regarding Zone Doubling is located on page 7 2 The NX 4 control panel will send an Expander Trouble once each hour if it senses that no devices have been enrolled This report will show Expander Trouble device zero 0 e lt E Sc BOARD INSTALLATION The metal enclosure should be installed with the door opening from top to bottom Refer to the diagram on the right ge Inside the can there are four slots for board insertion two on the top and two on the bottom of the can These allow the PC board to be xi 3 positioned vertically as shown in the diagram When you slide the Z q board between the grooves of the slots make sure the terminal strip is a H toward the front for wire connections Page 2 FEATURE DEFINITIONS If enabled the NX 4 will wait the programmed number of seconds in location 40 prior to sending an alarm During this delay time the Cancel LED will flash To abort the report type in a code and press the Cancel key The LED will extinguish If the report is not aborted within the allotted time the LED will extinguish when the report is sent Loc 40 and 110 149 pages 18 and 24 AC Fail Low Battery Report Warning The NX 4 can be programmed to report AC failure a
83. ypass or Instant mode if so programmed 24 HOUR SILENT SUPERVISED Creates an instant silent alarm regardless of the armed state of the control panel It will display on the keypad 11 RESERVED INTERIOR FOLLOWER WITH CROSS ZONE ENABLED This zone will be instant when the system is armed and no entry or exit delay is being timed It is delayed during entry and exit delay times If a Cross Zone is not being timed it will start a Cross Zone timer If a Cross Zone is being timed it will create an instant alarm This zone will automatically bypass when enabled in Segment 1 of Location 23 INSTANT ENTRY GUARD This zone creates an instant alarm whenever it is tripped and the Stay LED is off It will start an entry delay time 2 if it is tripped and the system is armed and the Stay LED is on ENTRY EXIT DELAY 1 WITH GROUP BYPASS ENABLED A trip will start entry delay 1 This zone will bypass when the Group Bypass command is entered at the keypad The lack of a trip during exit delay will enable the Automatic Bypass or Instant mode if so programmed INTERIOR FOLLOWER WITH GROUP BYPASS ENABLED This zone will be instant when the system is armed and no entry or exit delays are being timed It is delayed during entry exit delay times This zone will bypass when the Group Bypass command is entered at the keypad This zone will automatically bypass if enabled in Segment 1 of Location 23 INSTANT WITH GROUP BYPASS ENABLED This zone create

NX-4 Manual

Contents

Download Pdf Manuals

Related Search

Related Contents