Security GSM Alarm System USER MANUAL - Sunsky
Contents
1. effective under the normal defense area which is suitable when hosts at home because indoor infrared alarm function is canceled while the gate magnetisms on the door and window are still in a state of monitoring Multi checked defense area Under the situation of defense or intelligent defense if two or more detectors that set up multi checked are all triggered within 30 seconds the main engine will give an alarm Therefore based on this pattern none of the infrared detectors will misinform the events Note Set up two or more than two defense areas to be multi checked and they should be set up respectively Delay alarm defense area When the defense area is triggered and need alarm the main engine can delay the alarm the concrete delay time is determined by the Setting up alarm delay moreover the warning behavior can be canceled during delayed time Delete defense area It means delete selected defense areas only for wireless defense areas Note when you input 8 99 6 all of the wireless defense areas will be deleted Repeat triggered defense areas When the detector is triggered once the system will not alarm immediately Only when it is triggered again within 5 30 seconds after the first trigger the system will alarm Doorbell Either in the conditions of setting or cancelling fortification the area is just used as the doorbell rather than alarming fortification area Pager Either in the conditions of setti2. state Normally close In the state of no trigger the port is short connected with ground negative and brake is the trigger condition Normally open In the state of no trigger the port is disconnected with ground negative and short connection is the trigger condition Trigger when it is against normal Under these special conditions the connection status when the main engine turns from cancel defense into setting up defense is not triggered while once the status is changed it is the triggered situation set up the control of 12V power output 80 0 9 0 9 stands for the control state of 12 power supply and selections as below Q not output 12V 1 output 12V in the state of CF while close output under other states 2 output 12V in the state of SF while keeping outputting after alarm 3 output 12V in the state of SF while close output after alarm 4 output 12V in the state of bF while keeping outputting after alarm 5 output 12V in the state of bF while close output after alarm 6 output 12V in the state of SF or bF while keeping outputting after alarm 7 output 12V in the state of SF or bF while close output after alarm 8 output 12V in the state of alarming 9 keep outputting 12V Set the system time 07 Hour Minute the hour and minute are both 2 digits The hour is 24 hour clock For example if setting the time to be 9 18 enter
3. 07 09 18 Set the fortification time in due time 07 Hour Minute 0 9 are the hour and the minute The time format is the same as setting the system time format In 0 9 0 means deleting all timing fortification settings You can set 9 groups of timing fortification time in which the first five are long term ones periodic i e executing every day The sixth to ninth ones are one off fortification settings The system will delete this setting in due time For example setting fortification at 17 30 for the host every day and storing it in Group 2 the command is 0717302 If needing to set one off fortification at 12 00 temporarily enter 0712007 If removing all of the timing fortification settings enter 0700000 08 Set the time of canceling fortification in due time 08 Hour Minute 0 9 the detailed description for use is similar with the setting of timing fortification time Time broadcasting 09 Hour Minute 0 9 the detailed description for use is similar with the setting of timing fortification time The host will broadcast the time in due time alerting for 30 seconds GSM part of the instruction Station Indication of GSM part F4 means GSM is unavailable F5 turn on GSM F6 access the network The indicator lamp flashes every 3 seconds in normal condition If it can not access the network for a long time or shows F4 please turn off the power c
4. 2V programmable output drive current of 1A 12V fixed output power external electrical supply power Diagram is as follows ojqewwergoId Ajddns 1amog megaphone
5. Delete all the selected group telephone numbers Set up alarm delay 7 22 set up delay warning time in the delay mode zone in seconds Here stands for the number of seconds within the range between 0 to 99 Alarm ringing time 9 The alarm ringing time without human intervention after warning Here the range of is between 0 and 30 minutes Inquiry alarm defense area 0 9 Directly press 0 9 to inquiry the 10 latest alarm events and display alarm defense area O means the latest one The state of setting up defense area 8 0 9 Here stands for the serial number from 0 to 99 0 9 designates the setting mode of selected defense area 0 not use 1 common defense area 2 intelligent defense area 3 emergency defense area 4 multi checked defense area 5 delay alarm defense area 7 repeat triggered defense area 8 Doorbell 9 Pager For example press 8 2 2 then you can set up defense area 2 as the intelligent area Note When you input 99 it means all the wireless defense area will work according to this mode Emergency defense area No matter under the defended or undefended situations once triggered it will report to the police immediately which is suitable for the gas reaction smog reaction safe emergency accesses and other special occasions Intelligent defense area After selecting an area as intelligent defense one the defense area is not effective it is still
6. Security GSM Alarm System USER MANUAL System installation Brief introduction of system This alarm consists of main engine of alarm and various wireless connected accessories When people enter the defense region illegally the main engine will give sound of sirens and call the hosts so hosts can return home or inform neighboring relatives to cope with the instantly Also they can monitor the sound on the spot Alarm installation Insert the plug of telephone outside line into LINE2 of the main engine and connect LINE1 of the main engine with telephone using attached telephone wire of alarm Then joint up the power source and warning signal meanwhile the main engine will give a sound of B and light of the power source goes on which means the main engine starts working Gate magnetism installation Use the random equipped double side tape to stick a magnetic stripe on the door and affix the gate magnetic emission box on the doorframe Pay attention to put the magnetic strip close to the side with indicator lights of the emission box during installation assuring proper alignment and the smaller distance the better gate magnetic switch Launches the indicating lamp to owe presses the indicating lamp Infrared detector installation The principle of infrared detectors is to sense people s movement through sensing infrared signals generated by bodies and the detection range is usually 5 12 meters In
7. automatically and if it is correct you can have remote control of the system Please press after accomplish all operations then you can implement other operations and hang up telephone Press 1 to monitor the scene Press 2 to ring alarms Press 3 to close arisen Press 4 to set up defenses Press 5 to cancel defenses Press 6 to play records Press 7 to output 12V electric power Press 8 to close 12V output Press 9 to Open propaganda Press 0 to Close propaganda Press to affirm and hang up If the password is wrong or no any operations within 20 seconds it will hang up automatically Press 1 button once you can listen for 20 seconds 7 Processing method after receiving alarm In case of emergency main machine will dial the setup telephone numbers automatically and give alarm rings based on settings If the host s phone is in use or not able to connect the system will dial next alarm phone until it is dialed and hosts confirm It will play records after receiving alarm phone and the operation methods are similar to remote setup 8 Hosts cover wiring diagram SP SP connected loudspeaker speaker Which SP connect the power ground GND Cable zone wiring Lland L2 is the wired connection port zone zone one of a wired line to a common ground another wire signals the host access port host port is not wired to provide power but signal acquisition OUT is 1
8. e telephone above the setting times it will connect remote server automatically Here is the setting ring times while 0 means no remote setup Modify passwords 7 new password 4 numbers new password 4 numbers Use it when keyboard is locked and you forget password at the same time Recover factory settings 8 password The system will recover factory settings Clear telephone numbers vocal alarm alarm sounds cancel alarm delayed setting defense close the function of detecting disconnected telephone lines alarm ring time last for 5 minutes The instruction can not delete remote controller and defense area Set up alarm voice record 0 password It starts to record sounds at the place where 20 centimeters away from the main engine after correspond operations and the digital tube begin to countdown It will quit automatically and the main engine gives a long sound which means the record is successful Play audio tape 9 Raise the fixed line telephone connected with the main engine and then you can listen to the recording contents Press any button it will quit the play Open wired defense area 0 6 1 close wired defense area 0 6 0 Set up wired defense area 9 101 102 O 2 101 102 is the number for wired defense area 0 2 means state O normally close 1 normally open 2 trigger when it is against normal and 109 means all the wired defense areas are established based on this
9. eans all telephone are notified SMS direction after alarming in fortification area 03 1 9 refers to the area number 1 9 is the serial number of message One fortification area sends the text message of the specified series number after alarming For example set Alarm Area 12 to send the text message of Group 8 after alarming 03128 Brightness Adjustment of Digital Display 08 0 7 0 7 is 8 level brightness adjustment in which 8 is the brightest Operating the host by SMS use SMS to achieve set and unset functions query etc The command of setting fortification is SF the command of cancelling fortification is CF Brainpower Fortification BF Querying status STATUS Programmable 12V power command of outputting and closing the output ON and OFF Format password command For example use SMS to control the cancelling of fortification edit 0000 CF to the phone number of SIM card in the host and reply the message after the success All the above host commands can be operated by editing text message with the format of password the content of command If it sets the first phone number of 87654321 by SMS edit 0000 187654321 and send it to the host Application of alarm system 1 Set up defenses Press button on remote controller or Set up defenses button on panel and the main engine will give a sound of B then the main engine enter the d
10. efense situation or delayed defense state 2 Cancel defenses Press m button on remote controller or Cancel defenses button on panel and the main engine will give two sounds of B then the indicator lamp dies out so the main engine is in a state of no defenses 3 Emergency alarm Press button on remote controller or Alarm button on panel main engine will enter the state of emergency alarm instantly calling automatically and siren going off Press button on remote controller once is silent alarm while long press or two presses will open the siren 4 Intelligent defenses Press button on remote controller or Intelligent button on panel then main engine will enter the state of intelligent defense or delayed defense 5 Status indication of main engine digital tube Indicate SF for defense CF for no defense 99 for emergency alarm bF for intelligent defense F1 for alarm when telephone lines disconnect F3 means there is no learning defense area 1 98 means wireless defense area L1 L2 means wired defense area 6 Operation methods of remote setup You can use any telephone to dial the numbers of main engine and it will put on automatically after system detecting the ring times you have been setup When you hear the beep input passwords two sounds when the password is wrong while when the wrong time is above 3 the phone will hang up
11. frared sensor should be installed about 2 2 meters away from ground Aim straight at the detection ranges Moreover the infrared detector can be only installed in the room without facing the sunshine windows and other places where temperature is easy to change because the installed location may influence the detection range and accuracy Jau ZZ 1 4 W ZT S GSM Card Installation Pull SIM card cover behind the host press SIM card socket with your fingers and push backward then open the cover of card socket insert SIM card into the cover based on the notch keep the notched corner of SIM card in direction of that on board depress the cover and move forward to lock SIM card Function settings All the settings can be carried out under the undefended situation with a long ring for all the proper operations while two short sounds for wrong settings Adjust the volume of alarm siren 0 0 99 Adjust the volume when the alarm siren Choose between 0 to 99 0 is silent 99 is the loudest Silent alarm 00 no alarm whistle for warning Set up common alarm telephone numbers 1 5 set 1 5 groups telephone number 1 5 is the ordinal of the telephone number stands for telephone numbers Set up emergency phone numbers 6 2 The same method as above press alarm button of the main engine and the remote alarm button will call this group number Delete telephone numbers 1 6
12. heck the machine and then turn on again The following instructions are assumed that the password of host is 0000 If the password is changed please replace 0000 with the new password Set 9 groups of self editing short messages format password 1 9 SMS content 1 9 is the group number Group 9 is a message for emergency alert For example set Group 9 as This is an alarm in emergent fortification area You can edit 00009 This is an alarm in emergent fortification area no space by a mobile phone and send it to the phone number of SIM card in the host Query the contents of self editing short messages format password 1 9 1 9 is the serial number of stored messages For example if querying the content of Group 2 edit 00002 by a mobile phone and send it to the phone number of SIM card in the host Reply the message of Group 2 after success Set the types of alarm call 1 6 2 4 1 6 is the group number of telephone and 2 4 is the type 2 is to give a call only after alarming 3 is to send the text message only after alarming 4 is to send the message and give a call as well after alarming For example if setting Group 2 is to give a call and send the message as well enter 24 Set the change notification of external power status 05 0 to 7 external power on and off notifications In 0 7 0 is to close the function 1 6 is the group number of the telephone 7 m
13. ll of the wireless defense areas will be deleted Learn wireless keypad 03 learning methods and learning remote control wireless keyboard you can completely replace the panel keyboard Siren sound when using the remote control 21 on the remote control to turn on the siren sound Siren sound when using the remote control off 20 Use the remote control off the siren sound enable buzzer sound Open crack proof function 3 1 Open this function then none of the wireless remote controllers can cancel defense except for the cancel defense button of the main engine Close crack proof function 3 0 Close this function then remote controller of main engine can cancel defense normally Delayed time of setting up defense Inputting 4 can start the delayed time of setting up defense which means the formal defense will begin after seconds when you press the button Here the range of is between 0 and 99 Although it is in the state of delayed defense it can enter defense situation immediately if you repress the defense button Open the alarm function when telephone lines disconnect si When phone lines disconnect or failure it will give alarm rings to inform Close the alarm function when telephone lines disconnect 5 0 means main engine will not detect telephone lines disconnection or fault Remote setup telephone ringing times 6 If the ring times calling local fixed lin
14. ng or cancelling fortification the area is for pager use only rather than alarming fortification area The selection of common defense area and intelligent defense area has no influence of choosing Mode 4 5 7 8 9 so you choose intelligent or common defense area while selecting anyone of Mode 4 5 7 8 9 at the same time However The zone is set to emergency mode to another mode if you want to set the zone to zone please do not use patterns and then set the mode Input password password The designing password is 0000 which can be changed to another four numbers as the password Learning remote controller 0 The intelligent learning remote controller of main engine begin to count down 10 seconds When the remote or detector is triggered in 10 seconds the main engine can distinguish automatically and give a long sound presenting the location of remove memory which means successful study All of the code learning method is the same Learning detector 01 the intelligent learning remote controller of main engine Learning method is same as above Designated serial learning detector 8 Connect learning detector to the designated defense area number and is the defense number For example if you want to designate a detector to Defense Area 16 only input 8 16 Delete all of the remote controllers 0 2 means delete all of the remote controllers Note when you input 8 99 6 a
Download Pdf Manuals
Related Search