ETHERNET 10/100 TRANSCEIVER SERIES DL221/DL221A
Contents
1. L221 XYZ Transceiver 9dB 6km Multimode 2 fibers DL221 SM XYZ Transceiver 9dB 25km Singlemode 2 fibers DL221 SMHP XYZ Transceiver 18dB 50km Singlemode 2 fibers DL221 SMSP XYZ Transceiver 28db 80km Singlemode 2 fibers DL221 SMUP XY5 Transceiver 28db 110km Singlemode 2 fibers DL221A XYZ Transceiver 6db 2km Multimode 1 fiber DL221A SM XYZ Transceiver 9db 25km Singlemode 1 fiber DL221A SM2 XA3 Transceiver 18db 50km Singlemode 1 fiber DL221A SMHP XYZ Transceiver 18db 50km Singlemode 1 fiber DL221A SMSP XYZ Transceiver 28db 80km Singlemode 1 fiber Note Specify X packaging of the unit U 1U rack mount M modular R card cage rack mount Specify Y connector type A SC APC E SC B FC Z FC APC D ST Specify Z wavelength Multimode 8 850nm 2 1300nm Singlemode 3 1310nm 5 1550nm Add M for SNMP management Add 48 for 48VDC power For higher optical budgets and distances CWDM and DWDM systems contact factory Radiant Communications Corporation P O BOX 867 e 5001 Hadley Road e South Plainfield NJ 07080 800 969 3428 e Fax 908 757 7666 E mail sales rccfiber com e www rccfiber com RADIANT COMMUNICATIONS CORP DL221 REV B4 3 7 042. SERIES DL221 10 100 ETHERNET TRANSCEIVER USER MANUAL Radiant Communications Corporation P O BOX 867 e 5001 Hadley Road e South Plainfield NJ 07080 800 969 3427 Fax 908 757 7666 E mail sales rccfiber com e www rccfiber com RADIANT COMMUNICATIONS CORP DL221 REV B4 3 7 04 ETHERNET 10 100 TRANSCEIVER SERIES DL221 DL221A REV B4 3 FOR AC INPUT FRONT PANEL INDICATORS POWER ON WHEN UNIT HAS POWER 100M ON WHEN TWISTED PAIR IS WORKING 100Mbs OFF WHEN TWISTED PAIR IS WORKING AT 10Mbs LINK FX ON WHEN FIBER OPTIC LINK PRESENT TP ON WHEN TWISTED PAIR LINK PRESENT FDX FULL DUPLEX BOTH ARE LIT WHEN FIBER OPTIC LINK AND TWISTED PAIR ARE OPERATING AT FULL DUPLEX NOTE FIBER OPTIC LINK IS ALWAYS OPERATING AT FULL DUPLEX POWER 100M LINK FX TP FDX 10 100 BASE TX 100BASE TX PORT RJ 45 CONNECTOR HALF FULL DUPLEX SUPPORT VIA AUTO NEGOTIATION OR MANUAL 100m OVER UTP STP 100ohm CAT 5 CABLE X II MDI II MDI X SELECTION X CROSS OVER CABLE II STRAIGHT CABLE RADIANT COMMUNICATIONS CORP DL221 REV B4 3 1 04 2 MODE SETUP NOTE SWITCH 4 MUST BE IN THE ON UP POSITION FOR UNIT TO OPERATE AFTER CONFIGURATION OF UNIT POWER MUST BE RESET THIS CAN BE DONE BY REMOVING POWER TO UNIT OR TOGGLE SWITCH 4 DOWN THEN UP SETTINGS AUTO NEGOTIATION SW 1 SW 2 SW DOWN OFF 10M HALF DUPLEX SW 1 UP ON SW 2 SW DOWN OFF 10M FULL DUPLEX SW 1 UP ON SW 2 DOWN OFF
3. SW UP ON 100M HALF DUPLEX SW 1 UP ON SW 2 UP ON SW DOWN OFF 100M FULL DUPLEX SW 1 UP ON SW 2 UP ON SW 3 UP ON TROUBLESHOOTING POWER LED NOT LIT CHECK POWER SUPPLY CABLE TO MAIN POWER SUPPLY CHECK AC INPUT SOURCE CHECK SW 4 MUST BE UP ON POSITION LINK FX LED NOT LIT CHECK LIGHT LEVEL IN AND OUT OF UNIT REFER TO THE SPEC LABEL FOR PROPER LEVEL TP LED NOT LIT CHECK SETTING FOR STRAIGHT X OVER CABLE RESET POWER RADIANT COMMUNICATIONS CORP DL221 REV B4 3 7 04 3 FOR 5VDC INPUT FRONT PANEL INDICATORS RWR ON WHEN UNIT HAS POWER R ON WHEN TWISTED PAIR IS WORKING AT 100Mbs OFF WHEN TWISTED PAIR IS WORKING AT 10Mbs L ON WHEN FIBER OPTIC LINK PRESENT A ON WHEN TWISTED PAIR LINK PRESENT FX TX FDX FULL DUPLEX LIT WHEN FIBER OPTIC LINK AND TWISTED PAIR ARE OPERATING AT FULL DUPLEX NOTE FIBER OPTIC LINK IS ALWAYS OPERATING AT FULL DUPLEX RWR R L A FDX FX TX 10 100 BASE TX 100BASE TX PORT RJ 45 CONNECTOR HALF FULL DUPLEX SUPPORT VIA AUTO NEGOTIATION OR MANUAL 100m OVER UTP STP 100ohm CAT 5 CABLE NODE HUB MDI II MDI X SELECTION NODE CROSS OVER CABLE HUB STRAIGHT CABLE RADIANT COMMUNICATIONS CORP DL221 REV B4 3 7 04 SETTINGS AUTO NEGOTIATION SW 1 SW 2 SW DOWN OFF 10M HALF DUPLEX SW 1 UP ON SW 2 SW DOWN OFF 10M FULL DUPLEX SW 1 UP ON SW 2 DOWN OFF SW UP ON 100M HALF DUPLEX SW 1 UP ON SW 2 UP ON SW DOWN OFF 100M F
4. ULL DUPLEX SW 1 UP ON SW 2 UP ON SW 3 UP ON NOTE AFTER CONFIGURATION OF UNIT POWER MUST BE RECYCLED TROUBLESHOOTING RWR LED NOT LIT CHECK POWER SUPPLY ENSURE OUTPUT SVDC L LED NOT LIT CHECK LIGHT LEVEL IN AND OUT OF UNIT REFER TO THE SPEC LABEL FOR PROPER LEVEL A LED NOT LIT CHECK TWISTED PAIR CONNECTIONS RADIANT COMMUNICATIONS CORP DL221 REV B4 3 7 04 5 SPECIFICATIONS Standard Compliance IEEE802 3u 100BaseTx 100BaseFx 10BaseT 100BaseTx Port RJ 45 connector Half full duplex support via auto negotiation or manual 100m over UTP STP 100 ohm cat 5 cable Auto polarity correction MDI II MDI X selection 10BaseT switch selected 100BaseFx Port 1300nm SC connectors Optional Single Fiber DL221A Distance gt 100 km DL221 SMSP Full half duplex switch selected Diagnostics Per Channel Full duplex Link Activity 100BaseFx side Per System Power dual if redundant PS present Controls Fiber side FDX HDX Copper side 10 100 Mbps FDX HDX Auto sensing disable enable Environmental Physical Power supply 100 240 VAC 50 60 Hz 5VDC wall Power consumption 5 W max Operating temperature 0 45 C 32 113 F Storage temperature 30 65 C 22 149 F Humidity 10 90 non condensing NOTE Specifications subject to change without prior notice RADIANT COMMUNICATIONS CORP DL221 REV B4 3 7 04 PART NUMBER DESCRIPTION ATTEN MAX DISTANCE D
Download Pdf Manuals
Related Search